I-O DATA WN-AC1600DGR is a 2.4/5 GHz band 11ac router, based on
Qualcomm Atheros QCA9557.
Specification:
- SoC: Qualcomm Atheros QCA9557
- RAM: 128 MB
- Flash: 16 MB
- WLAN: 2.4/5 GHz
- 2.4 GHz: 2T2R (SoC internal)
- 5 GHz: 3T3R (QCA9880)
- Ethernet: 5x 10/100/1000 Mbps
- Switch: QCA8337N
- LED/key: 6x/6x(4x buttons, 1x slide switch)
- UART: through-hole on PCB
- Vcc, GND, TX, RX from ethernet port side
- 115200n8
Flash instruction using factory image:
1. Connect the computer to the LAN port of WN-AC1600DGR
2. Connect power cable to WN-AC1600DGR and turn on it
3. Access to "http://192.168.0.1/" and open firmware update page
("ファームウェア")
4. Select the OpenWrt factory image and click update ("更新") button
5. Wait ~150 seconds to complete flashing
Alternative flash instruction using initramfs image:
1. Prepare a computer and TFTP server software with the IP address
"192.168.99.8" and renamed OpenWrt initramfs image
"uImageWN-AC1600DGR"
2. Connect between WN-AC1600DGR and the computer with UART
3. Connect power cable to WN-AC1600DGR, press "4" on the serial
console and enter the U-Boot console
4. execute "tftpboot" command on the console and download initramfs
image from the TFTP server
5. execute "bootm" command and boot OpenWrt
6. On initramfs image, download the sysupgrade image to the device
and perform sysupgrade with it
7. Wait ~150 seconds to complete flashing
This commit also removes unnecessary "qca,no-eeprom" property from
the ath10k wifi node.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Tested with a dual pci QCA9558 board (LibreRouter v1) in three
configurations: enabling pcie0 only, pcie1 only and both enabled.
Signed-off-by: Santiago Piccinini <spiccinini@altermundi.net>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [removed ML notice]
Datasheet states that both PCI ranges are of 0x2000000 size:
0x1000_0000-0x11FF_FFF and 0x1200_0000-0x13FF_0000.
Signed-off-by: Santiago Piccinini <spiccinini@altermundi.net>
Reviewed-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [removed ML notice]
SoC: Qualcomm IPQ4019 (Dakota) 717 MHz, 4 cores
RAM: 256 MiB (Nanya NT5CC128M16IP-DI)
FLASH: 128 MiB (Macronix NAND)
WiFi0: Qualcomm IPQ4019 b/g/n 2x2
WiFi1: Qualcomm IPQ4019 a/n/ac 2x2
WiFi2: Qualcomm Atheros QCA9886 a/n/ac
BT: Atheros AR3012
IN: WPS Button, Reset Button
OUT: RGB-LED via TI LP5523 9-channel Controller
UART: Front of Device - 115200 N-8
Pinout 3.3v - RX - TX - GND (Square is VCC)
Installation:
1. Transfer OpenWRT-initramfs image to the device via SSH to /tmp.
Login credentials are identical to the Web UI.
2. Login to the device via SSH.
3. Flash the initramfs image using
> mtd-write -d linux -i openwrt-image-file
4. Power-cycle the device and wait for OpenWRT to boot.
5. From there flash the OpenWRT-sysupgrade image.
Ethernet-Ports: Although labeled identically, the port next to
the power socket is the LAN port and the other one is WAN. This
is the same behavior as in the stock firmware.
Signed-off-by: Marius Genheimer <mail@f0wl.cc>
[Dropped setup_mac 02_network in favour of 05_set_iface_mac_ipq40xx.sh,
reorderd 02_network entries, added board.bin WA for the QCA9886 from ath79,
minor dts touchup, added rng to 4.19 dts]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Robert Marko made a big effort to enable the rng on all
ipq40xx for 4.19, so let's continue the quest.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This factory binary i supposed to actually be unzipped and
untarred by the user as part of the installation process
(this NAS boots from harddisk), so name it "bootpart.tar.gz"
and not "factory.bin" so it is helpful for users.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
OCEDO Panda was added in b368373f, but only for
4.14 config. This patch fix 4.19 build for generic
and p2020 subtarget.
Signed-off-by: Pawel Dembicki <p.dembicki@wb.com.pl>
Buffalo WHR-G300N has a LED for power status indication, but it is not
connected to the GPIO and cannot be controlled by the kernel. So,
WHR-G300N uses "ROUTER" LED as the system status LED instead.
This commit changes it to use "DIAG" LED insted of "ROUTER" like
WHR-G301N in ath79 target.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
The R6120 has no 5GHz WLAN LED, the assigned GPIO in fact controls
the WAN LED.
Renames the LED accordingly in the device-tree.
Removes the 5GHz WLAN LED trigger.
Adds the correct WAN port LED trigger.
----
Currently, the MAC address for the Netgear R6120 is read from the NVRAM
partition. The offset for the MAC address however is not consistent
across devices or firmware versions.
Switch to using the factory partition like all other Netgear devices do.
----
The LAN ports of the R6120 are labled in reverse on the casing.
Adjust LuCI switchport numbering accordingly.
----
The WiFi eeprom offsets for the R6120 are currently wrong (5GHz offset
is bigger than the partition itself).
Fixes poor performance on 2.4 and 5 GHz.
Signed-off-by: David Bauer <mail@david-bauer.net>
The switch ports are seen one to one on the case.
Also remove unneeded secondary port numbers in this
case statement.
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
Change the ledtrig for LAN from netdev to switch.
Although eth1 comes out of the device at a single port,
this port is a switch-port and therefore the LED
must be triggered by that.
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
- Add the /etc/ssl/openssl.cnf as a separate package, to avoid breaking
the transitional mechanism, allowing libopenssl_1.0* and
libopenssl_1.1* to coexist.
- Remove the (selecting) dependency on @KERNEL_AIO
- Use global SOURCE_DATE_EPOCH
Signed-off-by: Eneas U de Queiroz <cote2004-github@yahoo.com>
Add a patch to enable the option to change the default ciphersuite list
ordering to prefer ChaCha20 over AES-GCM. This is used by default for
all platforms, except for x86_64 and aarch64. The assumption is that
only the latter have AES-specific CPU instructions and asm code that
uses them in openssl. Chacha20Poly1305 is 3x faster than AES-256 in
systems without AES instructions, with an equivalent strength.
Disable error messages by default except for devices with small flash or
RAM, to aid debugging.
Disable ASM by default on arm platform with small flash. Size
difference on mips and powerpc, the other platforms with small flash
devices, are not really relevant (using 100K as a threshold). All of
the affected platforms are source-only anyway.
Signed-off-by: Eneas U de Queiroz <cote2004-github@yahoo.com>
This version adds the following functionality:
* TLS 1.3
* AFALG engine support for hardware accelleration
* x25519 ECC curve support
* CRIME protection: disable use of compression by default
* Support for ChaCha20 and Poly1305
Patches fixing bugs in the /dev/crypto engine were applied, from
https://github.com/openssl/openssl/pull/7585
This increses the size of the ipk binray on MIPS32 by about 32%:
old:
693.941 bin/packages/mips_24kc/base/libopenssl1.0.0_1.0.2q-2_mips_24kc.ipk
193.827 bin/packages/mips_24kc/base/openssl-util_1.0.2q-2_mips_24kc.ipk
new:
912.493 bin/packages/mips_24kc/base/libopenssl1.1_1.1.1a-2_mips_24kc.ipk
239.316 bin/packages/mips_24kc/base/openssl-util_1.1.1a-2_mips_24kc.ipk
Signed-off-by: Eneas U de Queiroz <cote2004-github@yahoo.com>
Adds the following configuration options:
* using optimized assembler code (was always on before)
* use of x86 SSE2 instructions
* dyanic engine support
* include error messages
* Camellia, Gost, Idea, MDC2, Seed & Whirlpool algorithms
* RFC3779, CMS protocols
* VIA padlock hardware acceleration engine
Installs openssl.cnf with the library as it is used by engines
independent of the openssl util.
Fixes DTLS option that was innefective before.
Disables insecure SSL3 protocol and SHA0.
Adds openwrt-specific targets to Configure script, including asm support
for i386, ppc and mips64.
Strips building dirs from CFLAGS shown in binary.
Skips the fuzz directory during build.
Removed include/crypto/devcrypto.h that was included here, to use the
cryptodev-linux package, now that it was been moved from the packages
feed to the main openwrt repository.
This decreses the size of the ipk binray on MIPS32 by about 3.3%:
old:
706.957 bin/packages/mips_24kc/base/libopenssl1.0.0_1.0.2q-2_mips_24kc.ipk
199.294 bin/packages/mips_24kc/base/openssl-util_1.0.2q-2_mips_24kc.ipk
new:
693.941 bin/packages/mips_24kc/base/libopenssl1.0.0_1.0.2q-2_mips_24kc.ipk
193.827 bin/packages/mips_24kc/base/openssl-util_1.0.2q-2_mips_24kc.ipk
Signed-off-by: Eneas U de Queiroz <cote2004-github@yahoo.com>
ucert needs to check the firmware part with metadata, but without the signature.
Use the new fwtool mode to extract that without altering the firmware image inside
the check
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This allows extracing the firmware + metadata from a signed firmware without
altering the original image file
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In the case of SHARED_LIBS=y, don't use -export-dynamic to place *all*
symbols into the dynamic symbol table. Instead, use --dynamic-list to
export a smaller set of symbols similar to that defined in static-syms.h
in the case of SHARED_LIBS=n, avoiding an 11 KB tc package size increase.
Also increment PKG_RELEASE.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
This enables using the tc module m_xt.so, which uses the act_ipt kernel
module to allow tc actions based on iptables targets. e.g.
tc filter add dev eth0 parent 1: prio 10 protocol ip \
u32 match u32 0 0 action xt -j DSCP --set-dscp-class BE
Make the SHARED_LIBS parameter configurable and based on tc package
selection.
Fix a problem using the tc m_xt.so plugin as also described in
https://bugs.debian.org/868059:
Sync include/xtables.h from iptables to make sure the right offset is
used when accessing structure members defined in libxtables. One could
get “Extension does not know id …” otherwise. (See also: #868059)
Patch to sync the included xtables.h with system iptables 1.6.x. This
continues to work with iptables 1.8.2.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Simplify build and runtime dependencies on libelf, which allows tc and ip
to load BPF and XDP object files respectively.
Preserve optionality of libelf by having configuration script follow the
HAVE_ELF environment variable, used similarly to the HAVE_MNL variable.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Replace the old 'tc' with a singleton package variant which will be used
to enable additional functionality and limit it only to tc. Non-variant
packages will only be installed during 'tiny' variant builds, hence will
be configured without extra features, thus preserving previously limited
functionality and reduced package sizes.
Also set ip-tiny as the default variant, and install 'tiny' versions of
development libraries.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Compile-based feature detection (e.g. xtables, ipset support) was broken
due to silent compilation errors in the configure script, caused by a
Makefile variable KERNEL_INCLUDE referring to kernel build headers. Use
userspace headers by setting the same "user_headers" kernel include path
as used for the iptables build.
Remove redundant or unused Build/Configure definitions from package
Makefile, including KERNEL_INCLUDE, LIBC_INCLUDE and DBM includes.
Don't pass LDFLAGS within MAKE_FLAGS as this interferes with LDFLAGS in
tc/Makefile and masks a link parameter ("-Wl,-export-dynamic"). Instead,
use standard TARGET_LDFLAGS.
Replace EXTRA_CCOPTS in MAKE_FLAGS with cleaner TARGET_CPPFLAGS, and also
drop now unneeded patch 150-extra-ccopts.patch.
Enable defining XT_LIB_DIR from Makefile, needed to set the iptables
modules directory to something other than /lib/xtables, and also add
libxtables dependency. Both are needed with working xtables detection.
Note that libxtables is also pulled in by iptables, firewall or luci, so
this change has no size impact in most cases.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Since v4.13, iproute2 switched to a config.mk file with greater use of
pkg-config for library/feature detection. Replace the old Config patch
with one modifying the configure script but enabling the same changes:
- explicitly disable TC_CONFIG_ATM
- rely on feature detection for IP_CONFIG_SETNS and TC_CONFIG_XT
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Enable the built-in BPF JIT compiler for all 4.9, 4.14 and 4.19 kernels,
which should speed up cBPF and eBPF-based packet filtering (tc, iptables)
and packet sniffing (libpcap, tcpdump, fwknopd, etc).
This has minimal kernel size impact, increasing the size of uImage-lzma
(normally ~2 MB on mips_24kc or mips64el_mips64) by 5 KB for the MIPS32
arch cBPF JIT and by 9 KB for the MIPS64 arch eBPF JIT, on kernel 4.14.
With JIT enabled (cBPF only), the standard BPF test module (test_bpf.ko)
running on a DIR-835 (mips_24kc) used 33 CPU seconds, but 68 without JIT.
This change aligns with the notion of OpenWRT as the network go-to swiss
army knife for packet handling, especially on CPU-constrained platforms.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Add the test_bpf module that runs various test vectors against the BPF
interpreter or BPF JIT compiler. The module must be manually loaded, as
with the kmod-crypto-test module which serves a similar purpose.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Add em_ipset module to support tc filter classification by IP set. Build
as a standalone package to help avoid pulling in rest of kmod-sched and
isolate new dependency on kmod-ipt-ipset.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Add act_pedit, act_csum, act_gact and act_simple modules for additional
tc action support. Module act_simple helps with debug and logging, similar
to iptables LOG target, while act_gact provides common generic actions.
Modules act_pedit and act_csum support general packet mangling, and have
been the subject of feature requests and forum discussions (e.g. DSCP),
as well as being added to the Turris OS fork of OpenWrt ~2 years ago.
Also select dependency kmod-lib-crc32c to support act_csum.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
All tc ematch modules, including those in kmod-sched-core and kmod-sched,
use cls_basic as a core dependency. Relocate cls_basic from kmod-sched to
kmod-sched-core to avoid requiring kmod-sched unnecessarily.
This change is also backwards compatible since any past tc ematch users
will have had to install both kmod-sched-core and kmod-sched anyway.
Add the matchall kernel module cls_matchall introduced in kernel 4.8. The
matchall classifier matches every packet and allows the user to apply
actions on it. It is a simpler, more efficient replacement for the common
but cryptic tc classifier idiom "u32 match u32 0 0".
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Hardware
--------
CPU: Qualcomm Atheros QCA9561
RAM: 64M DDR2
FLASH: 16M SPI-NOR
ETH: 1x WAN - 2x LAN
WiFi: QCA9561 3T3R
BTN: 1x Reset - 1x WPS
LED: 1x Blue - 1x Red - 1x Yellow
UART: TX - GND - RX - VCC (From ethernet port)
115200n8 - 3.3V
Installation
------------
1. Connect to the device via UART.
2. Interrupt the U-Boot on power-on by pressing enter when prompted.
3. Connect you computer to one of the routers LAN ports.
Assign yourself the IP 192.168.31.10/24.
Copy the OpenWRT initramfs image to a tftp server root directory.
Rename the image to 'x4q.bin'.
4. Load the initramfs image to the router by executing following command
in U-Boot. The image will boot afterwards.
> tftpboot 0x81000000 x4q.bin; bootm
5. SCP the sysupgrade-image into '/tmp'.
Remember to assign yourself an IP in 192.168.1.0/24 for this step!
6. Install OpenWRT permanently by executing
> sysupgrade -n /tmp/<OpenWRT-sysupgrade-image>
Signed-off-by: David Bauer <mail@david-bauer.net>
Issues a wmi command to firmware when multicast rate change is received with the
new BSS_CHANGED_MCAST_RATE flag. Also fixes the incorrect fixed_rate setting
for CCK rates which got introduced with addition of ath10k_rates_rev2 enum.
By default the firmware uses 1Mbps and 6Mbps rate for management packets
in 2G and 5G bands respectively. But when the user selects different
basic rates from the userspace, we need to send the management
packets at the lowest basic rate selected by the user.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
