* QCA IPQ4019
* 256 MB of RAM
* 32 MB of SPI NOR flash (s25fl256s1)
- 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=20,variant=OM-A62
* 2T2R 5 GHz (channel 36-64)
- QCA9888 hw2.0 (PCI)
- requires special BDF in QCA9888/hw2.0/board-2.bin
bus=pci,bmi-chip-id=0,bmi-board-id=16,variant=OM-A62
* 2T2R 5 GHz (channel 100-165)
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=21,variant=OM-A62
* multi-color LED (controlled via red/green/blue GPIOs)
* 1x button (reset; kmod-input-gpio-keys compatible)
* external watchdog
- triggered GPIO
* 1x USB (xHCI)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
- phy@mdio3:
+ Label: Ethernet 1
+ gmac0 (ethaddr) in original firmware
+ 802.3at POE+
- phy@mdio4:
+ Label: Ethernet 2
+ gmac1 (eth1addr) in original firmware
+ 18-24V passive POE (mode B)
* powered only via POE
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.
The initramfs image can be started using
setenv bootargs 'loglevel=8 earlycon=msm_serial_dm,0x78af000 console=ttyMSM0,115200 mtdparts=spi0.0:256k(0:SBL1),128k(0:MIBIB),384k(0:QSEE),64k(0:CDT),64k(0:DDRPARAMS),64k(0:APPSBLENV),512k(0:APPSBL),64k(0:ART),64k(0:custom),64k(0:KEYS),15552k(inactive),15552k(inactive2)'
tftpboot 0x84000000 openwrt-ipq40xx-openmesh_a62-initramfs-fit-uImage.itb
set fdt_high 0x85000000
bootm 0x84000000
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Fix multiple syntax errors in shelscripts (of packages only)
These errors were causing many conditions to not working properly
Signed-off-by: Lorenzo Santina <lorenzo.santina@edu.unito.it>
[increase PKG_RELEASE, drop command substitution from directip.sh]
Signed-off-by: Mathias Kresin <dev@kresin.em>
Future Open Mesh u-boot versions are changing the check of the image files
(vmlinux, rootfs) from md5 to sha256. Having both in them should be enough
to ensure backward and forward compatibility.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49140
The u-boot on Open Mesh devices checks the whole transfered image against a
md5sum. This is stored inside the option filemd5sum inside the
fwupgrade.cfg. The bootloader will not check it when this setting is
missing and could therefore write invalid images to the flash.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 46925
It will be used for non OM2P boards as well.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 34200
