Commit Graph

37922 Commits

Author SHA1 Message Date
Felix Fietkau
39d03d9959 lantiq: fix broadcast packets leaking on the wrong vlan on xrx200
The ethernet driver uses a port map override via special tag to control
the ports on which multicast packets are sent. This was added to work
around an issue in the switch that was occasionally leaking packets onto
the wrong vlan.
Unfortunately the change had some leftover lines that were overwrting
the port map with a list of all ports, thus always leaking packets onto
the wront vlan.

Fix this by only enabling the override with the VLAN port map and only
if a matching VLAN port map was actually found

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-02-23 13:01:34 +01:00
Rafał Miłecki
5fed9ef842 kernel: move upstream accepted bcm47xxpart TRX cleanups
Use 0xx prefix for accepted patches.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2017-02-22 19:02:51 +01:00
Rafał Miłecki
5c1758d468 kernel: backport bcm47xxsflash support for reading 32 MiB flashes
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2017-02-22 19:01:50 +01:00
Stijn Tintel
349577adbf Revert "kernel: ar8327/ar8337: disable ARL access code to avoid lockups (FS#384)"
This reverts commit ec1a695daa.

Revert the workaround, the problem was properly fixed in
2374549916.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
(cherry picked from commit 5c49fecf72)
2017-02-22 12:07:30 +01:00
Günther Kelleter
7fd494d4b2 ar8216: flush ARL table during reset after init_globals
commit 33b72b8e0f
"ar8216: adjust ATU flushing in case of link changes"
introduced portwise flushing on link down events. Now the ARL table could
be in a chaotic state after boot where ar8xxx_sw_get_arl_table looped
forever (depending on the entries collected while booting).

Fixes FS#384.

Signed-off-by: Günther Kelleter <guenther.kelleter@devolo.de>
(cherry picked from commit 2374549916)
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2017-02-22 11:57:27 +01:00
Felix Fietkau
f6d94b0dd6 cmake: skip build system check on compile
cmake checks the build system and its variables on its own to detect if
the makefiles need to be regenerated.
Unfortunately this can invalidate overrides passed in the
Build/Configure step. On non-Linux systems this breaks the build when
switching between targets of the same package architecture.

Fix this by forcibly disabling the build system check and relying on the
LEDE build system to take care of these things

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-02-21 16:16:25 +01:00
Baptiste Jonglez
59508e309e dnsmasq: Add upstream patch fixing SERVFAIL issues with multiple servers
This fixes FS#391 for lede-17.01

Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
2017-02-20 18:13:44 +01:00
Jo-Philipp Wich
06f3b91902 kernel: update kernel 4.4 to version 4.4.50
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2017-02-20 16:02:54 +01:00
Stijn Tintel
5612114090 Revert "px5g-standalone: provide px5g via PROVIDES"
This reverts commit cc66f819b4.

This commit causes opkg to install px5g-standalone instead of px5g when
installing luci-ssl. As luci-ssl depends on mbedtls, using
px5g-standalone makes no sense. Next to that, it creates deprecated SHA1
certificates. Revert the commit to avoid pxg5-standalone to be
installed by accident.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
(cherry picked from commit ca8aee0c57)
2017-02-20 15:17:20 +01:00
Alberto Bursi
4d1ab84f1e uboot-kirkwood: fix goflexhome/net bootcommand
Goflexhome/net use uImage, and to boot an uImage the u-boot
must use bootm command, not bootz.

Fixes the "i cannot boot LEDE with this u-boot" issue that I
found out myself with my goflexnet.

Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
2017-02-19 21:00:19 +01:00
Thibaut VARENE
cdeb2322ea ar71xx: Remove images for rb-941-2nd
The code that generates this image is broken in many ways.

The new code currently in master generates images that will not be compatible
with the ones in 17.01. To avoid a migration nightmare, this patch removes
image generation for this device in 17.01

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-02-19 20:52:52 +01:00
Jo-Philipp Wich
f79926cb94 sdk: emit proper tag references for base URLs
Properly resolve symbolic tag names when constructing the base feed Git url
and avoid emitting "HEAD" references when building from detached commits.

Fixes #495, #501.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2017-02-19 20:50:24 +01:00
Mathias Kresin
0a26490fe4 lantiq: set the internet led interface according to wan interface
Use the nas0 interface for the netdev trigger as default. Use the ptm0
interface for xRX200 boards to match the default wan interface set in
02_network.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-02-18 16:52:05 +01:00
Mathias Kresin
6a6e3a4928 lantiq: introduce lantiq_is_vdsl_system
Move the code to check if the current system is a system with vdsl
support to a dedicate function to make it reusable.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-02-18 16:52:05 +01:00
Mathias Kresin
c5879b0676 lantiq: fix ARV7519RW22 switch port indexing
Fixes FS#454.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-02-18 16:52:05 +01:00
Felix Fietkau
c835c9ebe5 uhttpd: use sha256 when generating certificates with openssl (FS#512)
Patch from attachment to FS#512

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-02-17 14:43:11 +01:00
Stijn Tintel
6ebb8723a6 dropbear: bump PKG_RELEASE
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
(cherry picked from commit 27040dbf89)
2017-02-17 12:31:52 +01:00
Joseph C. Sible
f527436364 dropbear: enable SHA256 HMACs
The only HMACs currently available use MD5 and SHA1, both of which have known
weaknesses. We already compile in the SHA256 code since we use Curve25519
by default, so there's no significant size penalty to enabling this.

Signed-off-by: Joseph C. Sible <josephcsible@users.noreply.github.com>
(cherry picked from commit 0bf85ef048)
2017-02-17 12:31:39 +01:00
Felix Fietkau
f88bd7cd0f ar71xx: fix ethernet PLL configuration for QCA956x
QCA956x is configured like AR934x, not like the older chips.
Should fix ethernet hangs when using the WAN port without SGMII

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-02-17 12:17:39 +01:00
David Woodhouse
828a024c81 x86: Set default baud rate on Geode images to 115200
Prior to commit 1496b95a0 ("x86: clean up default grub baudrate
settings") we had three different baud rates for the Geode targets:
19200 for net5501, 38400 for alix2, and 115200 for Geos.

It doesn't seem that there's a very good reason for varying from our
default 115200 baud, so let's make the Geode target do that instead.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2017-02-17 10:30:30 +01:00
David Woodhouse
63a8424702 x86: Add Geos profile for Geode subtarget
This makes the Geode images actually useful again. The Geos profile
should include the relevant hardware for that board, and the Default
profile adds the via-rhine adapter which seems to have been present in
the net5501 and alix targets killed in commit 9e0759ea26 ("x86: merge
all geode based subtargets into one").

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2017-02-17 10:30:30 +01:00
Chris Blake
808f6a500c x86: Add board configs for the PC Engines APU2
This adds the default LED and network settings for the PC Engines APU2
when running under the x86 target.

[dwmw2: Change Ethernet port setup]
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
2017-02-17 10:29:24 +01:00
David Woodhouse
6d6db65d82 x86: Enable DIAG LED on Geos
Based on a patch from Chris Blake <chrisrblake93@gmail.com>, except let's
do it by using the LED configuration instead of hard-coding it for each
board type. And try using /bin/board_detect to do the default behaviour,
on the first boot where the config hasn't yet been generated.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2017-02-17 10:28:52 +01:00
Chris Blake
bd5b5c749a x86: Move Traverse Geos configs into x86 base-files
This change moves the files in 657418d to the root of the x86 target.
This is done in preperation for adding more devices under other
subtargets.

CC: David Woodhouse <dwmw2@infradead.org>

Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
2017-02-17 10:28:45 +01:00
David Woodhouse
06e0c30336 x86: Add configuration back for Traverse Geos
When we merged all the Geode boards into one generic target, the default
network and LED configuration was lost. Put it back.

Fixes: 9e0759ea26 ("x86: merge all geode based subtargets into one")
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2017-02-17 10:28:39 +01:00
Rafał Miłecki
982dd01ac3 Mark targets using kernel 3.18 as source-only
We're past v17.01.0-rc2 phase and these few targets are stuck at 3.18
kernel. We obviously don't want to have targets like this built for the
release, especially with 3.18 being EOL.

It may be not too late for bringing these targets back for the next
minor release, so just mark them as source-only instead of dropping
completely.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2017-02-17 06:58:33 +01:00
Furong Xu
25b7295617 ramips: fix the number of uarts for MT7688
Same as MT7621 and MT7628, MT7688 allows up to 3 uarts

Signed-off-by: Furong Xu <xfr@outlook.com>
2017-02-16 09:54:30 +01:00
Furong Xu
71ea3b4814 ramips: fix PWM pin mux conflict in dtsi
GPIO18 and GPIO19 on OMEGA2(+) should be GPIO mode, enable PWM lead to a conflict

[    0.290633] rt2880-pinmux pinctrl: pin io18 already requested by pinctrl; cannot claim for 10005000.pwm
[    0.299722] rt2880-pinmux pinctrl: pin-18 (10005000.pwm) status -22
[    0.305729] rt2880-pinmux pinctrl: could not request pin 18 (io18) from group pwm0  on device rt2880-pinmux
[    0.315131] mtk-pwm 10005000.pwm: Error applying setting, reverse things back

Keep PWM disabled.

Signed-off-by: Furong Xu <xfr@outlook.com>
2017-02-16 09:54:17 +01:00
Cezary Jackiewicz
44aec27112 ugps: fix typo
Removing redundant spaces from the name of the option. Without fix:

root@LEDE:~# opkg install ugps
Installing ugps (2016-10-24-32a6b2b7-1) to root...
Downloading http://downloads.lede-project.org/releases/17.01-SNAPSHOT/packages/mips_24kc/base/ugps_2016-10-24-32a6b2b7-1_mips_24kc.ipk
Configuring ugps.
uci: Parse error (invalid character in name field) at line 3, byte 23
uci: Parse error (invalid character in name field) at line 3, byte 23
sh: out of range
root@LEDE:~# uci show gps
uci: Parse error (invalid character in name field) at line 3, byte 23

With this fix:

root@LEDE:~# uci show gps
gps.@gps[0]=gps
gps.@gps[0].tty='ttyACM0'
gps.@gps[0].adjust_time='1'

Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
2017-02-16 09:54:14 +01:00
Mirko Parthey
7efe538ac1 brcm47xx: fix button inversion for Asus WL-500W
The Asus WL-500W buttons are active high,
but the software treats them as active low.
Fix the inverted logic.

Signed-off-by: Mirko Parthey <mirko.parthey@web.de>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2017-02-16 00:20:33 +01:00
Mirko Parthey
be007c580e brcm47xx: fix USB driver choice for Asus WL-500W
BCM4704 SoC has only USB 1.1 core:
ssb: Core 3 found: USB 1.1 Hostdev (cc 0x808, rev 0x03, vendor 0x4243)
but this device actually comes with two USB 2.0 ports.

It appears embedded controller isn't used but instead there are two PCI
attached controllers (next to the BCM4321 wireless card):
1106:3038 VT82xx/62xx UHCI USB 1.1 Controller
1106:3104 USB 2.0

Choose a set of USB drivers which actually support this hardware.

Signed-off-by: Mirko Parthey <mirko.parthey@web.de>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2017-02-15 23:54:36 +01:00
Felix Fietkau
dbb8e04472 qos-scripts: fix module load commands (FS#438)
fq_codel is built-in, and xt_CONNMARK is provided by the xt_connmark
module

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-02-15 14:02:04 +01:00
Felix Fietkau
853bad5af2 kernel: fix crashes on MIPS when loading kernel modules under memory pressure
When memory is tight, modules may need to be loaded into vmalloc()
space. The code then has to generate jump trampolines which enable
relocations between vmalloc space and physical address space.

The code had a bug that was freeing these trampolines even when the
module was successfully loaded.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-02-15 13:23:58 +01:00
Rafał Miłecki
df49e49bc7 mdns: update and rename package to the umdns
This update includes numerous small fixes for:
1) Interfaces setup
2) Packets parsing
3) Sending replies
Without this there were multiple problems with exchanging information
between (u)mdns and other implementations (including (u)mdns as well).

This also follows project rename to umdns which was required to avoid
confusion with Apple's mdnsd from mDNSResponder project.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2017-02-15 13:07:21 +01:00
Felix Fietkau
72d045b2a6
ar71xx: fix DEFAULT_PACKAGES for mikrotik devices
Include packages from the default profile for NAND devices

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-02-15 12:59:22 +01:00
Felix Fietkau
b8c9ded999 build: add buildbot specific config option for setting defaults
This can be used to tweak the buildbot behavior without having to change
buildbot's configuration.
It will also allow us to add more aggressive clean steps (e.g. on
toolchain changes), which would break developers' workflows if enable
by default.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-02-15 11:37:13 +01:00
Furong Xu
eea6df8255 tools: patch-image: fix file descriptor leak.
Maybe this is committed by mistake, fix it.

Signed-off-by: Furong Xu <xfr@outlook.com>
2017-02-15 09:37:15 +01:00
John Crispin
30a4966053 octeon: only copy sysupgrade file if present
this caused

'mv: can't rename '/mnt/sysupgrade.tgz': No such file or directory'

when running sysupgrade -n

Signed-off-by: John Crispin <john@phrozen.org>
2017-02-15 09:37:15 +01:00
Sven Eckelmann
152f57f509 ar71xx: Add missing device package om-watchdog for MR1750
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2017-02-15 09:35:56 +01:00
Sven Eckelmann
fcba5ee47a ar71xx: add OpenMesh A40 to OpenMesh A60 profile
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2017-02-15 09:35:55 +01:00
Sven Eckelmann
f30f25c33e ar71xx: extract ath10k wifi board.bin for the OpenMesh A40 board
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2017-02-15 09:35:55 +01:00
Sven Eckelmann
d6d9f256ff package/uboot-envtools: add OpenMesh A40 support
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2017-02-15 09:35:54 +01:00
Sven Eckelmann
e6057ed207 package/om-watchdog: add OpenMesh A40 support
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2017-02-15 09:35:53 +01:00
Sven Eckelmann
4a36180970 ar71xx: enable sysupgrade for the OpenMesh A40
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2017-02-15 09:35:52 +01:00
Sven Eckelmann
552bc355d1 ar71xx: add user-space support for the OpenMesh A40
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2017-02-15 09:35:52 +01:00
Sven Eckelmann
14add3f724 ar71xx: add kernel support for the OpenMesh A40 board
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2017-02-15 09:35:51 +01:00
Sven Eckelmann
b194b3d97f ar71xx: create profile and build image for the OpenMesh A60 board
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2017-02-15 09:35:50 +01:00
Sven Eckelmann
facbdec0b5 ar71xx: extract ath10k wifi board.bin for the OpenMesh A60 board
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2017-02-15 09:35:49 +01:00
Sven Eckelmann
8785ebc471 package/uboot-envtools: add OpenMesh a60 support
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2017-02-15 09:35:49 +01:00
Sven Eckelmann
eb383710e2 package/om-watchdog: add OpenMesh A60 support
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2017-02-15 09:35:48 +01:00