I-O DATA WN-DX2033GR is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based on
MT7621A.
Specification:
- SoC : MediaTek MT7621A
- RAM : DDR3 128 MiB
- Flash : Raw NAND 128 MiB (Macronix MX30LF1G18AC-TI)
- WLAN : 2.4/5 GHz
- 2.4 GHz : 2T2R, MediaTek MT7603E
- 5 GHz : 4T4R, MediaTek MT7615
- Ethernet : 5x 10/100/1000 Mbps
- Switch : MediaTek MT7530 (SoC)
- LEDs/Keys : 2x/3x (2x buttons, 1x slide-switch)
- UART : through-hole on PCB
- J5: 3.3V, TX, RX, NC, GND from triangle mark
- 57600n8
- Power : 12 VDC, 1 A
Flash instruction using initramfs image:
1. Boot WN-DX2033GR normally
2. Access to "http://192.168.0.1/" and open firmware update page
("ファームウェア")
3. Select the OpenWrt initramfs image and click update ("更新") button
to perform firmware update
4. On the initramfs image, download the sysupgrade.bin image to the
device and perform sysupgrade with it
5. Wait ~120 seconds to complete flashing
Notes:
- The hardware of WN-DX2033GR and WN-AX2033GR are almost the same, and
it is certified under the same radio-wave related regulations in Japan
- The last 0x80000 (512 KiB) in NAND flash is not used on stock firmware
- stock firmware requires "customized uImage header" (called as "combo
image") by MSTC (MitraStar Technology Corp.), but U-Boot doesn't
- uImage magic ( 0x0 - 0x3 ) : 0x434F4D42 ("COMB")
- header crc32 ( 0x4 - 0x7 ) : with "data length" and "data crc32"
- image name (0x20 - 0x37) : model ID and firmware versions
- data length (0x38 - 0x3b) : kernel + rootfs
- data crc32 (0x3c - 0x3f) : kernel + rootfs
- There are 2x important flags in the flash:
- bootnum : select os partition for booting (persist, 0x4)
- 0x01: firmware
- 0x02: firmware_2
- debugflag : allow interrupt kernel loader, it's named as "Z-LOADER"
(Factory, 0xFE75)
- 0x00: disable debug
- 0x01: enable debug
MAC addresses:
LAN : 50:41:B9:xx:xx:90 (Factory, 0xE000 (hex) / Ubootenv, ethaddr (text))
WAN : 50:41:B9:xx:xx:92 (Factory, 0xE006 (hex))
2.4 GHz : 50:41:B9:xx:xx:90 (Factory, 0x4 (hex))
5 GHz : 50:41:B9:xx:xx:91 (Factory, 0x8004 (hex))
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
GPIOs > 31 require special handling. This patch fixes both the
initialisation and direction get/set operations.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Sander Vanheule <sander@svanheule.net>
Add additional header information required for newer
bootloaders found on DIR-2660-A1 & A2.
Also remove the MTD splitter compatible from the second firmware
partition, as OpenWrt only supports handling of the first one.
Signed-off-by: Alan Luck <luckyhome2008@gmail.com>
[rephrase commit message, remove removal of read-only flags]
Signed-off-by: David Bauer <mail@david-bauer.net>
The rockchip platform supports squashfs SD card images. However, the
resulting image is not padded to completely fill the rootfs partition.
Because of that, the f2fs overlay might not be erased, resulting in
uci-defaults not bing executed or the configuration not being erased,
even though drop config was selected.
Modify the image generation process so the image is padded to cover the
entire root filesystem partition.
Signed-off-by: David Bauer <mail@david-bauer.net>
Remove use of DEVICE_TITLE in favor of the
DEVICE_VENDOR and DEVICE_MODEL as used by
all other targets.
Signed-off-by: Moritz Warning <moritzwarning@web.de>
Remove use of DEVICE_TITLE in favor of the
DEVICE_VENDOR and DEVICE_MODEL as used by
all other targets.
Signed-off-by: Moritz Warning <moritzwarning@web.de>
Using `make info` show the current target, revision, default packages
and available profiles. This commits adds the used architecture.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Meraki wrote the ethernet MAC-address of the device
onto the eeprom (AT24C64) at the fixed location 0x66
to 0x6C. Let's fetch it from there.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
commit 5ec60cbe9d ("scripts: mkits.sh: replace @ with - in nodes")
broke support for Meraki MR32 and this patch makes the replacement
configurable allowing for specifying the @ or - or whatever character
that is desired to retain backwards compatibility with existing devices.
For example, this patch includes the fix for the Meraki MR32 in
target/linux/bcm53xx/image for meraki_mr32:
DEVICE_DTS_DELIMITER := @
DEVICE_DTS_CONFIG := config@1
Fixes: 5ec60cbe9d ("scripts: mkits.sh: replace @ with - in nodes")
Signed-off-by: Damien Mascord <tusker@tusker.org>
[Added tags, checkpatch.pl fixes, noted that this is for old stuff]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
With GCC11, memcpy doesn't work here as it assumes a size of 0. Use
ioremap to avoid it.
Fixed parameter type to match board_get_mac_address.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
This fixes:
Distributed Switch Architecture (NET_DSA) [Y/n/m/?] y
Tag driver for Atheros AR9331 SoC with built-in switch (NET_DSA_TAG_AR9331) [N/m/y/?] n
Tag driver for Broadcom switches using in-frame headers (NET_DSA_TAG_BRCM) [N/m/y/?] n
Tag driver for Broadcom legacy switches using in-frame headers (NET_DSA_TAG_BRCM_LEGACY) [N/m/y/?] (NEW)
Error in reading or end of file.
Fixes: 8fa1b576bb ("linux: update b53 upstream driver")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Specifying serial in bootargs is not needed since the commit
ffeb37047e ("procd: update to git HEAD"). It's thanks to the procd
commit 2cfc26f8456a ("inittab: detect active console from kernel if no
console= specified").
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Build cortexa7 subtarget with DSA driver for MDIO-connected Broadcom
BCM53xxx switches. This is needed for the Lamobo R1 aka. BananaPi
BPi-R1 board which comes with such a switch IC.
Remove old swconfig driver from target kernel config as the only board
using it is now supported by the DSA driver.
No changes to device tree are needed as upstream DTS already got a
DSA switch definition and we are just using that upstream source.
Update default network config of the Lamobo R1 to create lan bridge
with all 4 lan ports.
Introduce DEVICE_COMPAT_VERSION for the board to inform users about
having the re-create their network configuration and add device alias
as Bananapi BPi-R1 while at it.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Changes from 5.4 to 5.10:
-------------------------
- patches from 5.4 are all upstream for 5.10 execpt for
0004-PCI-add-quirk-for-Gateworks-PLX-PEX860x-switch-with-.patch
- disable block device data integrity (DIF/DIX/T10) in default config
(CONFIG_BLK_DEV_INTEGRITY)
This feature is only supported by:
- Enterprise SAS/SCSI HBAs and Disks
- Software raid
- NVMEs with metadata capabilities (most don't have this)
None of which are part of any octeontx boards.
- arm64 TEXT_OFFSET (0x80000) has been removed after 5.4
This will break Uimages with kernel load addresses that aren't 2MiB
aligned any longer. Resulting in the kernel silently fail to boot.
For Gatworks newport boards for example, the uimage kernel load
and execute address is 0x20080000. These need to be changed to
0x20000000 when running kernels beyond 5.4.
Tested-on: Gateworks Newport GW64xx
Signed-off-by: Daniel Danzberger <daniel@dd-wrt.com>
Linksyses Audi EA3500 and Viper E4200/E4500 have too small kernel
partition size when kernel 5.10 is used. This patch change kernel
partition to maximum size allowed by u-boot.
Kernel size is overlapping rootfs now, like mvebu Linksyses and stock
partition table. It fix back to stock via sysupgrade, which was broken
since 18.06.
Fixes: 9808b9ae02 ("kirkwood: switch to kernel 4.9")
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
The ZyXEL GS1900-24HPv2 is a 24 port PoE switch with two SFP ports, similar to the other GS1900 switches.
Specifications
--------------
* Device: ZyXEL GS1900-24HPv2
* SoC: Realtek RTL8382M 500 MHz MIPS 4KEc
* Flash: 16 MiB
* RAM: W631GG8MB-12 128 MiB DDR3 SDRAM
(stock firmware is configured to use only 64 MiB)
* Ethernet: 24x 10/100/1000 Mbps, 2x SFP 100/1000 Mbps
* LEDs: 1 PWR LED (green, not configurable)
1 SYS LED (green, configurable)
24 ethernet port link/activity LEDs (green, SoC controlled)
24 ethernet port PoE status LEDs
2 SFP status/activity LEDs (green, SoC controlled)
* Buttons: 1 "RESTORE" button on front panel
1 "RESET" button on front panel
* Power 120-240V AC C13
* UART: 1 serial header (J41) with populated standard pin connector on
the left edge of the PCB, angled towards the side.
The casing has a rectangular cutout on the side that provides
external access to these pins.
Pinout (front to back):
+ GND
+ TX
+ RX
+ VCC
Serial connection parameters for both devices: 115200 8N1.
Installation
------------
OEM upgrade method:
(Possible on master once https://patchwork.ozlabs.org/project/openwrt/patch/20210624210408.19248-1-bjorn@mork.no/ is merged)
* Log in to OEM management web interface
* Navigate to Maintenance > Firmware > Management
* If "Active Image" has the first option selected, OpenWrt will need to be
flashed to the "Active" partition. If the second option is selected,
OpenWrt will need to be flashed to the "Backup" partition.
* Navigate to Maintenance > Firmware > Upload
* Upload the openwrt-realtek-generic-zyxel_gs1900-24hp-v2-initramfs-kernel.bin
file by your preferred method to the previously determined partition.
When prompted, select to boot from the newly flashed image, and reboot the switch.
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade -n /tmp/openwrt-realtek-generic-zyxel_gs1900-24hp-v2-squashfs-sysupgrade.bin
it may be necessary to restart the network (/etc/init.d/network restart) on
the running initramfs image.
U-Boot TFTP method:
* Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10).
* Set up a TFTP server on your client and make it serve the initramfs image.
* Connect serial, power up the switch, interrupt U-boot by hitting the
space bar, and enable the network:
> rtk network on
* Since the GS1900-24HPv2 is a dual-partition device, you want to keep the OEM
firmware on the backup partition for the time being. OpenWrt can only boot
from the first partition anyway (hardcoded in the DTS). To make sure we are
manipulating the first partition, issue the following commands:
> setsys bootpartition 0
> savesys
* Download the image onto the device and boot from it:
> tftpboot 0x84f00000 192.168.1.10:openwrt-realtek-generic-zyxel_gs1900-24hp-v2-initramfs-kernel.bin
> bootm
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade -n /tmp/openwrt-realtek-generic-zyxel_gs1900-24hp-v2-squashfs-sysupgrade.bin
it may be necessary to restart the network (/etc/init.d/network restart) on
the running initramfs image.
Signed-off-by: Soma Zambelly <zambelly.soma@gmail.com>
like commit 78c1ed6. Without this,Some USB port on H3 baseboard
can' work. So, need enable MUSB support on this target.
Signed-off-by: Zhao Yu <574249312@qq.com>
This patch fixes the forwarding behavior of bridge in bridge
configurations with DSA.
Without it, the configuration of the upper bridge might overwrite
settings of the lower bridge. For example, a vlan-aware bridge
with DSA interfaces in it might be offloaded to the DSA hardware. If the
bridge interface itself gets slave of a different bridge without vlan
filtering, the vlan filtering setting of the lower bridge is overwritten
by the upper bridge, which results in an incorrect hardware
configuration.
This was backported from kernel 5.7.
Ref: https://lore.kernel.org/netdev/20191222192235.GK25745@shell.armlinux.org.uk/
Fixes: FS#3996
Signed-off-by: Fabian Bläse <fabian@blaese.de>
Designated initializers are required when using the randstruct GCC
plugin, otherwise an error like the following is seen:
./include/linux/lzma.h:60:31: error: positional initialization of field in 'struct' declared with 'designated_init' attribute [-Werror=designated-init]
Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
These options are selectable when some of the kernel debug options like
KERNEL_SOFTLOCKUP_DETECTOR are selected.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Move kernel version to 5.10 as has been tested by many users
with positive feedback.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[Tested on: ipq8064/g10; ipq8065/nbg6817]
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
The board data file for the Plasma Cloud PA2200 is not part of the default
board-2.bin which is shipped by ath10k-board-qca4019. A typo in the device
package name resulted in a not correctly selected package for the device
specific board-2.bin. The wifi driver has therefore loaded the wrong
calibration information into the wifi chip.
Fixes: 4871fd2616 ("ipq40xx: add support for Plasma Cloud PA2200")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The board data file for the Plasma Cloud PA1200 is not part of the default
board-2.bin which is shipped by ath10k-board-qca4019. A typo in the device
package name resulted in a not correctly selected package for the device
specific board-2.bin. The wifi driver has therefore loaded the wrong
calibration information into the wifi chip.
Fixes: ea5bb6bbfe ("ipq40xx: add support for Plasma Cloud PA1200")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The board data file for the EnGenius EMR3500 is not part of the default
board-2.bin which is shipped by ath10k-board-qca4019. As result, the wrong
calibration information will be loaded into the wifi chip.
Fixes: 3f61e5e1b9 ("ipq40xx: add support for EnGenius EMR3500")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The board data file for the EnGenius EMD1 is not part of the default
board-2.bin which is shipped by ath10k-board-qca4019. As result, the wrong
calibration information will be loaded into the wifi chip.
Fixes: 51f3035978 ("ipq40xx: add support for EnGenius EMD1")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
1. Add support for Marvell CN9130 SoC
2. Add support for CP115,and create an armada-cp11x.dtsi file which will be used to instantiate both CP110 and CP115
3. Add support for AP807/AP807-quad,AP807 is a major component of CN9130 SoC series
4. Drop PCIe I/O ranges from CP11x file and externalize PCIe macros from CP11x file
Signed-off-by: Ian Chang <ianchang@ieiworld.com>
The default value for CONFIG_RCU_CPU_STALL_TIMEOUT was changed from 60
seconds to 21 seconds in 2012 in the upstream kernel. Some targets
already use 21 seconds.
This patch changes the default value in the generic configuration to 21
seconds and removes the target specific configuration options.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Rui Salvaterra <rsalvaterra@gmail.com>
It's been brewing on my cortexa9 subtarget (Turris Omnia) for months.
Perfectly stable.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
[modify subject to match previous updates]
Signed-off-by: Paul Spooren <mail@aparcar.org>
Sitecom WLR-4100 v1 002 (marked as X4 N300) is a wireless router
Specification:
SoC: MT7620A
RAM: 64 MB DDR2
Flash: MX25L6405D SPI NOR 8 MB
WIFI: 2.4 GHz integrated
Ethernet: 5x 10/100/1000 Mbps QCA8337
USB: 1x 2.0
LEDS: 2x GPIO controlled, 5x switch
Buttons: 1x GPIO controlled
UART: row of 4 unpopulated holes near USB port, starting count from
white triangle on PCB:
VCC 3.3V
GND
TX
RX
baud: 115200, parity: none, flow control: none
Installation
Connect to one of LAN (yellow) ethernet ports,
Open router configuration interface,
Go to Toolbox > Firmware,
Browse for OpenWrt factory image with dlf extension and hit Apply,
Wait few minutes, after the Power LED will stop blinking, the router is
ready for configuration.
Known issues
Some USB 2.0 devices work at full speed mode 1.1 only
MAC addresses
factory partition only contains one (binary) MAC address in 0x4.
u-boot-env contains four (ascii) MAC addresses, of which two appear
to be valid.
factory 0x4 **:**:**:**:b9:84 binary
u-boot-env ethaddr **:**:**:**:b9:84 ascii
u-boot-env wanaddr **:**:**:**:b9:85 ascii
u-boot-env wlanaddr 00:AA:BB:CC:DD:12 ascii
u-boot-env iNICaddr 00:AA:BB:CC:DD:22 ascii
The factory firmware only assigns ethaddr. Thus, we take the
binary value which we can use directly in DTS.
Additional information
OEM firmware shell password is: SitecomSenao
useful for creating backup of original firmware.
There is also another revision of this device (v1 001), based on RT3352 SoC
Signed-off-by: Andrea Poletti <polex73@yahoo.it>
[remove config DT label, convert to nvmem, remove MAC address
setup from u-boot-env, add MAC address info to commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This device is a wireless access point working on the 2.4 GHz and 5 GHz
band, based on Qualcomm/Atheros QCA9563 + QCA9886.
Specification
- 775 MHz CPU
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- QCA9563: 2.4 GHz 3x3
- QCA9886: 5 GHz
- AR8033: 1x 1 Gbs Ethernet
- 4x LED, WPS factory reset and power button
- bare UART on PCB (accessible through testpoints)
Methods for Flashing:
- Apply factory image in OEM firmware web-gui. Wait a minute after the
progress bar completes and restart the device.
- Sysupgrade on top of existing OpenWRT image
- Solder wires onto UART testpoints and attach a terminal.
Boot the device and press enter to enter u-boot's menu. Then issue the
following commands
1. setenv serverip your-server-ip
setenv ipaddr your-device-ip
2. tftp 0x80060000 openwrt-squashfs.bin (Rembember output of size in
hex, henceforth "sizeinhex")
3. erase 0x9f030000 +"sizeinhex"
4. cp.b 0x80060000 0x9f030000 0x"sizeinhex"
5. reboot
Recover:
- U-boot serial console
Signed-off-by: Robert Balas <balasr@iis.ee.ethz.ch>
[convert to nvmem]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Specifications:
- SoC: MT7622
- RAM: 512MB
- Flash: MX35LF1GE4AB 128MB SPI NAND
- Ethernet: RTL8367S 5x1GbE
- WiFi: 2.4G: MT7622 5G: MT7615N x2
- Other ports: USB3.0 x1
Flash instruction:
*important*: upgrade vendor firmware to at least V7.1cu.643_B20200521
1. hold the reset button and power on the device. wait for about 10s
before releasing the reset button.
2. upload sysupgrade.bin via u-boot recovery page on http://192.168.1.1
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
I2C_BCM_IPROC selects I2C_SLAVE which in turn makes two new symbols
available: I2C_SLAVE_EEPROM and I2C_SLAVE_TESTUNIT. That was causing:
I2C support (I2C) [M/n/y/?] m
Enable compatibility bits for old user-space (I2C_COMPAT) [N/y/?] n
I2C device interface (I2C_CHARDEV) [M/n/?] m
I2C bus multiplexing support (I2C_MUX) [N/m/?] n
Autoselect pertinent helper modules (I2C_HELPER_AUTO) [N/y/?] n
SMBus-specific protocols (I2C_SMBUS) [N/m/?] n
I2C/SMBus Test Stub (I2C_STUB) [N/m/?] n
I2C slave support (I2C_SLAVE) [Y/?] y
I2C eeprom slave driver (I2C_SLAVE_EEPROM) [N/m/?] n
I2C eeprom testunit driver (I2C_SLAVE_TESTUNIT) [N/m/?] (NEW)
Ideally I2C_SLAVE should probably be packaged as kmod-i2c-slabe. For now
just modify kmod-i2c-bcm-iproc to fix kernel compilation.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This makes USB controller driver work with USBs that are always powered
on (don't require toggling any GPIO).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
As Adrian Schmutzler suggested on github [1] the device should follow the
default behaviour on ethernet using a static address instead using dhcp.
[1] 8d497b6570
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
w2914ns-v2, 11acnas, and freezio use almost same board and thus share a
common dtsi file. Now that LED labels do not contain "devicename" since
commit c846dd91f0 ("ramips: remove model name from LED labels"), let's
move the leds nodes to dtsi and remove them from dts.
Note that freezio has only one USB 3.0 port and adding &ehci_port2 trigger
does not incur any visible changes.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
The Device/seama shared definition requires BLOCKSIZE, so it should
have a default value for this variable.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The partitions that have compatible property set are skipped by mtd if
they are not contained inside a partitions node and this breaks
fetching MAC address from "default-mac" partition.
Fix this by defining all the partitions inside partitions node with
compatible = "fixed-partitions" as nvmem requires the standard
partitions scheme to work correctly.
Fixes: FS#3945
Fixes: cd36d71655 ("ipq806x/dts: Add Archer C2600 DTS")
Fixes: 0458a8993c ("ipq806x: convert mtd-mac-address to nvmem
implementation")
Signed-off-by: Filip Matijević <filip.matijevic.pz@gmail.com>
Reviewed-by: Ansuel Smith <ansuelsmth@gmail.com>
[adjust commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This includes:
1. BCM5301X changes from 5.14 and queued 5.15 stuff
2. NSP changes from 5.11 - 5.15 for kernel 5.10
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
CONFIG_RCU_{NEED_SEGCBLIST,STALL_COMMON} are set basically everywhere. Move them
to the generic kconfigs. And resort the generic kconfigs while at it.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Based on the existing documentation [1][2], I dare anyone to demonstrate that
we need to fine-tune these RCU parameters. The (performance) breakage potential
for doing so is immense, so let's just please put down this loaded footgun.
Disable CONFIG_RCU_EXPERT and its dependent symbols. Additionally, remove the
CONFIG_RCU_EXPERT symbol from the target kconfigs which contain it.
[1] https://www.kernel.org/doc/Documentation/RCU/Design/Data-Structures/Data-Structures.html
[2] https://lwn.net/Articles/777214/
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
There is a longlasting warn about unused defined try_to_force_load.
Fix this by including this function only when actually used.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Change `DAP-2965` to `DAP-2695` for device selection in menuconfig.
Fixes: cd09f26660 ("ath79: add support for D-Link DAP-2695-A1")
Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
[add Fixes]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The TP-Link TL-MR3020 v3 only has a single MAC address assigned for
ethernet LAN as well as WiFi. This MAC address is also printed on the
casing.
Signed-off-by: David Bauer <mail@david-bauer.net>
The GigaDevices GD25Q64B found on the TL-MR3020 v3 supports the fast
read instruction. Add the required DT property in order to enable usage
of this property.
Signed-off-by: David Bauer <mail@david-bauer.net>
The GigaDevices GD25Q64B supports higher SPI clocks than 10 MHz. While
100 MHz do not work reliably, 50 MHz works without issues.
Signed-off-by: David Bauer <mail@david-bauer.net>
The modec{1,2} keys are actually switches.
Add the respective DTS properties to avoid accidental activation of
failsafe mode.
Signed-off-by: David Bauer <mail@david-bauer.net>
The uImage.FIT partition uses page mapping without properly handling
paging errors. This can lead to Kernel Oops in case of read errors
while trying to parse uImage.FIT partitions.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
These options doesn't show up unless some kernel packages are selected,
so they are not covered by kernel_menuconfig.
Manually add them so that a build with all kmods can pass without user
interaction.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
there's no driver level remapping of oob data in the new spi-nand
driver and bmt oob signature starts at 0x0 of the dumped oob data.
change the default value to 0 for the new spi-nand driver.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
mtd->size will be overrided by BMT which makes all mtd requests made by
bmt fail in request size checking.
this commit changes the driver to check against actual chip size in chip
info as a workaround.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
we now have a standalone mtd driver and the old spi-mem driver along
with the hack in spi-nand core can be removed.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
This patch enables new spi-nand driver for mt7622 and mt7629.
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
This patch adds a new spi-nand driver which implements the SNFI of mt7622
and mt7629.
Unlike the existing snfi driver which makes use of the spi-mem framework
and the spi-nand framework with modified ecc support, this driver is
implemented directly on the mtd framework with other components untouched,
and provides better performance, and behaves exactly the same as the nand
framework.
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
This was old code from the AR71XXs target days that
doesn't get compiled and used anymore.
Bringing up AR92xx and earlier chips from their
OWL-Emulator state is currently done by the upstream
ath9k-pci-owl-loader module. (see the kmod-owl-loader
package).
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The Onion Omega is a hardware development platform with built-in WiFi.
https://onioniot.github.io/wiki/
Specifications:
- QCA9331 @ 400 MHz (MIPS 24Kc Big-Endian Processor)
- 64MB of DDR2 RAM running at 400 MHz
- 16MB of on-board flash storage
- Support for USB 2.0
- Support for Ethernet at 100 Mbps
- 802.11b/g/n WiFi at 150 Mbps
- 18 digital GPIOs
- A single Serial UART
- Support for SPI
- Support for I2S
Flash instructions:
The device is running OpenWrt upon release using the ar71xx target.
Both a sysupgrade
and uploading the factory image using u-boots web-UI do work fine.
Depending on the ssh client, it might be necessary to enable outdated
KeyExchange methods e.g. in the clients ssh-config:
Host 192.168.1.1
KexAlgorithms +diffie-hellman-group1-sha1
The stock credentials are: root onioneer
For u-boots web-UI manually configure `192.168.1.2/24` on your computer,
connect to `192.168.1.1`.
MAC addresses as verified by OEM firmware:
2G phy0 label
LAN eth0 label - 1
LAN is only available in combination with an optional expansion dock.
Based on vendor acked commit:
commit 5cd49bb067 ("ar71xx: add support for Onion Omega")
Partly reverts:
commit fc553c7e4c ("ath79: drop unused/incomplete dts")
Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me>
Give users more control by exposing ephy leds.
Signed-off-by: David Yang <mmyangfl@gmail.com>
[remove execute bit on 01_leds, add status for gpio2]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Generally u-boot should keep read-only to avoid mis-overwriting and
bricking the device, but u-boot-env could be safely modified with u-boot
setenv tool.
Signed-off-by: David Yang <mmyangfl@gmail.com>
The flash is Winbond 25Q128. As it has large rom, better to increase flash
frequency to 70MHz according to the flash spec and enable fast-read.
Signed-off-by: David Yang <mmyangfl@gmail.com>
This patch adds support for D-Link DAP-1325-A1 (Range Extender Wi-Fi N300)
Specifications:
- SoC: 580Mhz MT7628NN
- RAM: 64MB, DDR2 SDRAM
- Storage: 8MB, SPI (W25Q64JVSSIQ)
- Ethernet: 1x 10/100 LAN port
- WIFI: 2.4 GHz 802.11bgn
- LED: Status (2x to provide 3 colors), Wi-Fi Signal Strength (4x)
- Buttons: Reset, WPS
- UART: Serial console (57600, 8n1)
Row of 4 holes near LAN port, starting from square hole:
3.3V, TX,RX,GND
- FCC ID: fccid.io/KA2AP1325A1/
Installation:
Failsafe UI
Firmware can be uploaded with Failsafe UI web page:
- turn device off
- press and hold reset button
- turn device on
- keep holding reset until red wifi strength led turns on (ab. 10sec)
- connect to device through LAN port
PC must be configured with static ip (192.168.0.x)
- connect to 192.168.0.50
- select image to be flashed and upload.
Device will reboot after successful update
Serial port/TFTP server
- Connect through serial connectors on PCB (e.g. with teraterm)
- Set up a TFTP server, and connect through LAN with static IP
- Put image file in the root of the server
- Boot the device and select '2' at U-Boot startup
- Set device IP, server IP and image file name
- Start upload and flash
Signed-off-by: Giovanni Cascione <ing.cascione@gmail.com>
[fix whitespaces in DTS, convert to nvmem, add mtd-eeprom]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Specifications:
- SoC: QCA9558
- DRAM: 128MB DDR2
- Flash: 16MB SPI-NOR
- Wireless: on-board abgn 2×2 2.4GHz radio
- Ethernet: 2x 10/100/1000 Mbps (1x 802.11af PoE)
- miniPCIe slot
Flash instruction:
- From u-boot
tftpboot 0x80500000 openwrt-ath79-generic-compex_wpj558-16m-squashfs-sysupgrade.bin
erase 0x9f030000 +$filesize
cp.b $fileaddr 0x9f030000 $filesize
boot
- From cpximg loader
The cpximg loader can be started either by holding the reset button
during power up. Once it's running, a TFTP-server under 192.168.1.1 will accept
the image appropriate for the board revision that is etched on the board.
For example, if the board is labelled '6A07':
tftp -v -m binary 192.168.1.1 -c put openwrt-ath79-generic-compex_wpj558-16m-squashfs-cpximg-6a07.bin
Signed-off-by: Romain Mahoux <romain@mahoux.fr>
[convert to nvmem, remove redundant lan_mac in 02_network]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The problem has been fixed in f47cb405ca ("ipq806x: fix pci broken
on bootm command"), now the pcie part can be written in the usual way.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Reviewed-by: Ansuel Smith <ansuelsmth@gmail.com>
Specifications:
* SOC: MT7620A + MT7610E
* ROM: 16 MiB spi flash (W25Q128FVSG)
* RAM: 128 MiB DDR2 (W971GG6KB-25)
* WAN: 10/100M *1
* LAN: 10/100M *4
* USB: Type-A USB2.0 *1
* SD: MicroSD *1
* Button: Reset *1
* Antennas: 2.4 GHz *2 + 5 GHz *1
* TTL Baudrate: 57600
* U-Boot Recovery: IP: 10.10.10.123, Server: 10.10.10.3
Installation:
* Web UI Update
1. Open http://192.168.10.1/upgrade.html in the browser.
2. Rename firmware to a short name like firmware.bin and then upload it.
3. Fill in the password column with the following content:
password | mtd -x mIp2osnRG3qZGdIlQPh1 -r write /tmp/firmware.bin firmware
* TFTP + U-Boot
1. Connect device with a TTL cable.
2. Press "2" when booting to select "Load system code then write to Flash via TFTP".
3. Upload firmware by tftpd64, it will boot when write instruction is executed.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Specifications:
* SOC: MT7628AN + MT7612E
* ROM: 8 MiB Flash
* RAM: 64 MiB DDR2
* WAN: 10/100M *1
* LAN: 10/100M *3
* Button: Reset *1
* LEDs: orange *1, white *1
* Antennas: 2.4 GHz *2 + 5 GHz *2
* TTL Baudrate: 57600
* TFTP Upgrade: IP: 192.168.51.1, Server: 192.168.51.100
MAC addresses as verified by OEM firmware:
use address source
2g *:d8 factory 0x0004 (label)
5g *:d9 factory 0x8004
LAN *:d7 factory $label -1
WAN *:da factory $label +2
Installation (TFTP + U-Boot):
* Connect device with a TTL cable and open a serial session by
PuTTY.
* Press "2" when booting to select "Load system code then write
to Flash via TFTP".
* Configure the IP of local host server.
* Upload firmware by tftpd64, it will boot when write instruction
is executed.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[fix DTS line endings, fix label MAC address, adjust status LED
names, convert mtd-mac-address-increment to mac-address-increment]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The partition name in the device dts is '0:ART'.
Be independent to prevent this part from becoming
incorrect once the kernel v5.4 gone.
Fixes: da8428d277 ("ipq806x: add support for Askey RT4230W REV6")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Descriptions：
Phicomm K2 (PSG1218) got a new "permanent_config" partition after
update firmware to v22.5. This partition located in front of the
firmware partition, same as The Phicomm K2P and K2G. Due to this
change the new bootloader can't load previous firmware any more.
This commit is aimed at add support for Phicomm K2 which official
firmware version is 22.5.x or newer. For which runs old firmware
version, just update OpenWrt that has a prefix of "k2-v22.4".
For uniform naming, this commit also changed the model name
PSG1218 to a more recognizable name K2, refer to Phicomm K2G,
K2P K2T.
OpenWrt selection table:
official firmware version OpenWrt
v22.4.x.x or older phicomm_k2-v22.4
v22.5.x.x or newer phicomm_k2-v22.5
Installation:
Same as Phicomm K2G, K2P, PSG1208.
a. TFTP + U-Boot
b. Open telnet by some web page vulnerability (Search Baidu by key
words "K2 telnet"), and then we can upload firmware image to
/tmp and write it to firmware partition with mtd instruction.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[rebase, add/harmonize version in model variables, fix version typo
in commit message, wrap commit message properly]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Atheros DB120 reference board.
Specifications:
SoC: QCA9344
DRAM: 128Mb DDR2
Flash: 8Mb SPI-NOR, 128Mb NAND flash
Switch: 5x 10/100Mbps via AR8229 switch (integrated into SoC),
5x 10/100/1000Mbps via QCA8237 via RGMII
WLAN: AR9300 (SoC, 2.4G+5G) + AR9340 (PCIe, 5G-only)
USB: 1x 2.0
UART: standard QCA UART header
JTAG: yes
Button: 1x reset
LEDs: a lot
Slots: 2x mPCIe + 1x mini-PCI, but using them requires
additional undocumented changes.
Misc: The board allows to boot off NAND, and there is
I2S audio support as well - also requiring
additional undocumented changes.
Installation:
1. Original bootloader
Connect the board to ethernet
Set up a server with an IP address of 192.168.1.10
Make the openwrt-ath79-generic-atheros_db120-squashfs-factory.bin
available via TFTP
tftpboot 0x80060000 openwrt-ath79-generic-atheros_db120-squashfs-factory.bin
erase 0x9f050000 +$filesize
cp.b $fileaddr 0x9f050000 $filesize
2. pepe2k's u-boot_mod
Connect the board to ethernet
Set up a server with an IP address of 192.168.1.10
Make the openwrt-ath79-generic-atheros_db120-squashfs-factory.bin
available via TFTP, as "firmware.bin"
run fw_upg
Reboot the board.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
[explicit factory recipe in generic.mk, sorting in 10-ath9k-eeprom,
convert to nvmem, use fwconcat* names in DTS, remove unneeded DT
labels, remove redundant uart node]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch adds support for the Ubiquiti PowerBeam M2 (XW), e.g. PBE-M2-400,
a 802.11n wireless with a feed+dish form factor. This device was previously
supported by the ar71xx loco-m-xw firmware.
Specifications:
- Atheros AR9342 SoC
- 64 MB RAM
- 8 MB SPI flash
- 1x 10/100 Mbps Ethernet port, 24 Vdc PoE-in
- Power and LAN green LEDs
- 4x RSSI LEDs (red, orange, green, green)
- UART (115200 8N1)
Flashing via stock GUI:
- Downgrade to AirOS v5.5.x (latest available is 5.5.10-u2) first (see
https://openwrt.org/toh/ubiquiti/powerbeam installation instructions)
- Upload the factory image via AirOS web GUI.
Flashing via TFTP:
- Use a pointy tool (e.g., unbent paperclip) to keep the
reset button pressed.
- Power on the device (keep reset button pressed).
- Keep pressing until LEDs flash alternatively LED1+LED3 =>
LED2+LED4 => LED1+LED3, etc.
- Release reset button.
- The device starts a TFTP server at 192.168.1.20.
- Set a static IP on the computer (e.g., 192.168.1.21/24).
- Upload via tftp the factory image:
$ tftp 192.168.1.20
tftp> bin
tftp> trace
tftp> put openwrt-ath79-generic-ubnt_powerbeam-m2-xw-squashfs-factory.bin
WARNING: so far, no non-destructive method has been discovered for
opening the enclosure to reach the serial console. Internal photos
are available here: https://fcc.io/SWX-NBM2HP
Signed-off-by: Russell Senior <russell@personaltelco.net>
The commit [1] added support for Ubiquiti PowerBeam M (XW), tested
on the PBE-M5-400. But, it turns out the PBE-M2-400 has a different
ethernet configuration, so make the support specific to the m5 version
in anticipation of adding specific support for the m2 in a separate
commit.
[1] 12eb5b2384 ("ath79: add support for Ubiquiti PowerBeam M (XW)")
Signed-off-by: Russell Senior <russell@personaltelco.net>
[fix model name in DTS, format commit reference in commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Built clock drivers for G3DSYS and AUDSYS into the kernel to allow
multimedia features (GPU and audio) to work if they exist.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Rearrange all voltage triplets for "opp_table0" to match the
specifications. "opp-microvolt" and "opp-microvolt-<name>" triplets
are in order of <target min max>, and NOT <min target max>.
Previously, the CPU would *always* spend its time at the "minimum"
voltage, ignoring the actual intended target. This is a regression
from previous behavior.
On an NBG6817 with a Qualcomm CPU of PVS bin #2...
(see &opp_table0 -> opp-1725000000 -> opp-microvolt-speed0-pvs2-v0)
* Before:
/usr/bin/tail -n +1 /sys/kernel/debug/opp/cpu0/opp\:1725000000/supply-0/u_volt_*
==> /sys/kernel/debug/opp/cpu0/opp:1725000000/supply-0/u_volt_max <==
1260000
==> /sys/kernel/debug/opp/cpu0/opp:1725000000/supply-0/u_volt_min <==
1200000
==> /sys/kernel/debug/opp/cpu0/opp:1725000000/supply-0/u_volt_target <==
1140000
* After:
/usr/bin/tail -n +1 /sys/kernel/debug/opp/cpu0/opp\:1725000000/supply-0/u_volt_*
==> /sys/kernel/debug/opp/cpu0/opp:1725000000/supply-0/u_volt_max <==
1260000
==> /sys/kernel/debug/opp/cpu0/opp:1725000000/supply-0/u_volt_min <==
1140000
==> /sys/kernel/debug/opp/cpu0/opp:1725000000/supply-0/u_volt_target <==
1200000
To check voltages and frequencies at run time, use...
/bin/cat /sys/kernel/debug/regulator/regulator_summary &&
/bin/cat /sys/kernel/debug/clk/clk_summary | grep "hfpll"
See
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/tree/Documentation/devicetree/bindings/opp/opp.txt?h=v5.4.142#n91
Fixes: 1e25423be8 ("ipq806x: refresh dtsi patches")
Signed-off-by: Shane Synan <digitalcircuit36939@gmail.com>
Reviewed-by: Ansuel Smith <ansuelsmth@gmail.com>
[commit message style cleanup, another kernel refresh]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Thanks to a hint from Michael Siegenthaler in 4b4fa2f9fe ("ramips:
fix ethernet MAC address on Omega2"), the label MAC address of
the Onion Omega 2(+) can be set based on its documentation [1].
[1] https://docs.onion.io/omega2-docs/mac-address.html
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The current patch produces the following error when CONFIG_DMABUF_HEAPS is
enabled:
drivers/built-in.a: member drivers/dma-buf/heaps in archive is not an object
Fixes: b10d604459 ("kernel: add linux 5.10 support")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Backport support for dual-role USB 2.0 as that's what is actually
built-into MT7623.
Improve HDMI console by enabling VT and setting up tty1..tty6.
Re-add accidentally removed CONFIG_ARM_ARCH_TIMER.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
According to https://docs.onion.io/omega2-docs/mac-address.html, 0x28 is
the correct location to read the address on Onion Omega 2(+) devices.
This fixes a regression introduced by commit 77e850fe76 ("ramips: tidy up
MAC address setup for Linkit Smart and Omega2"), which was a cleanup that
intended to preserve existing behavior. In my testing with v19.07.7,
however, the MAC address determined from the device tree takes precedence
over the one set by 02_network, so the aforementioned commit actually
changed the behavior.
Signed-off-by: Michael Siegenthaler <msiegen@google.com>
[Adapt patch to nvmem usage]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In order to make HDMI console available on the BananaPi BPi-R2 select
various Kconfig symbols which are useful for systems with graphics.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Do not deactivate the kernel configuration symbol CONFIG_STAGING in the
target configurations any more. This prevented the build of the exfat.ko
for example.
Fixes: FS#3979
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The ext3 driver was already removed, the kernel config options are only
there for backwards compatibility. The eth4 driver takes care of ext3
file systems. The ext4 driver also handled ext2 file systems.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The ext3 driver was already removed, the kernel config options are only
there for backwards compatibility. The eth4 driver takes care of ext3
file systems.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Convert this series by moving the definitions to the individual
devices.
Now all devices on ramips are converted.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Due to use of a script when migrating from mtd-mac-address, a few
of the definitions are redundant in DTSI and DTS files. Remove
those and consolidate the definitions in parent DTSI files in a
few cases.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Due to use of a script when migrating from mtd-mac-address, a few
of the definitions are redundant in DTSI and DTS files. Remove
those.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Since the nvmem-based approach for retrieving MAC addresses
appears to depend on the addresses being set up after the
partitions, it is no longer possible to keep the MAC address
setup in shared DTSI files while the partitions itself are
set up in DTS files for the individual devices.
In ath79 the firmware partition is typically located somewhere
"in the middle" of the partition table. Thus, it's not trivial
to share the partitions containing MAC address information in
a common DTSI (like we did in some cases on ramips).
In this commit, MAC address setup is thus moved to the relevant
partitions, and in most cases needs to be duplicated. While
the duplication is not really nice, it eventually provides a
cleaner and more tidy setup, making the DTS(I) file
fragmentation a bit more logical. This should also help
with adding new devices, as information is distributed across
less locations.
For consistency, this commit also moves the mtd-cal-data property
"down" together with the MAC address setup, so it's not based
on a partition before the latter is defined either. (This is
only done for those files touched due to nvmem conversion.)
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Convert most of the cases from mtd-mac-address to nvmem where
MAC addresses are set in the DTSI, but the partitions are only
located in the device DTS. This posed some problems earlier, since
in these cases we are using partitions before they are defined,
and the nvmem system did not seem to like that.
There have been a few different resolution approaches, based on
the different tradeoffs of deduplication vs. maintainability:
1. In many cases, the partition tables were identical except for
the firmware partition size, and the firmware partition was
the last in the table.
In these cases, the partition table has been moved to the
DTSI, and only the firmware partition's "reg" property has
been kept in the DTS files. So, the updated nvmem definition
could stay in the DTSI files as well.
2. For all other cases, splitting up the partition table would
have introduced additional complexity. Thus, the nodes to be
converted to nvmem have been moved to the DTS files where the
partitioning was defined.
3. For Netgear EX2700 and WN3000RP v3, the remaining DTSI file
was completely dissolved, as it was quite small and the name
was not really nice either.
4. The D-Link DIR-853 A3 was converted to nvmem as well, though
it is just a plain DTS file not taken care of in the first
wave.
In addition, some minor rearrangements have been made for tidyness.
Not covered (yet) by this patch are:
* Various unielec devices
* The D-Link DIR-8xx family
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The bootloader will look for a configuration section named ap.dk01.1-c2
in the FIT image. If this doesn't exist, the device won't boot.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
The mt76x8 subtarget is the only one in ramips that stores the
mediatek,mtd-eeprom property directly in the "root" mt7628an.dtsi.
This is not optimal for a few different reasons:
* If you don't really know it or are used to other (sub)targets,
the property will be set somewhat magically.
* The property is set based on &factory partition before (if at all)
this partition is defined.
* There are several devices that have different offset or even
different partitions to read from, which will then be overwritten
in the DTS files. Thus, definitions are scattered between root
DTSI and individual files.
Based on these circumstances, the "root" definition is removed and
the property is added to the device-based DTS(I) files where needed
and applicable. This should be easier to grasp for unexperienced
developers and will move the property closer to the partition
definitions.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
While an image layout based on MBR and 'bootfs' partition may be easy
to understand for users who are very used to the IBM PC and always have
the option to access the SD card outside of the device (and hence don't
really depend on other recovery methods or dual-boot), in my opinion
it's a dead end for many desirable features on embedded systems,
especially when managed remotely (and hence without an easy option to
access the SD card using another device in case things go wrong, for
example).
Let me explain:
* using a MSDOS/VFAT filesystem to store kernel(s) is problematic, as a
single corruption of the bootfs can render the system into a state
that it no longer boots at all. This makes dual-boot useless, or at
least very tedious to setup with then 2 independent boot partitions
to avoid the single point of failure on a "hot" block (the FAT index
of the boot partition, written every time a file is changed in
bootfs). And well: most targets even store the bootloader environment
in a file in that very same FAT filesystem, hence it cannot be used
to script a reliable dual-boot method (as loading the environment
itself will already fail if the filesystem is corrupted).
* loading the kernel uImage from bootfs and using rootfs inside an
additional partition means the bootloader can only validate the
kernel -- if rootfs is broken or corrupted, this can lead to a reboot
loop, which is often a quite costly thing to happen in terms of
hardware lifetime.
* imitating MBR-boot behavior with a FAT-formatted bootfs partition
(like IBM PC in the 80s and 90s) is just one of many choices on
embedded targets. There are much better options with modern U-Boot
(which is what we use and build from source for all targets booting
off SD cards), see examples in mediatek/mt7622 and mediatek/mt7623.
Hence rename the 'sdcard' feature to 'legacy-sdcard', and prefix
functions with 'legacy_sdcard_' instead of 'sdcard_'.
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This resolves incosnsitencies of the configured RX / TX flow control
modes between different boards or bootloaders.
Signed-off-by: David Bauer <mail@david-bauer.net>
The chip supports clock speeds up to 50 MHz, however it won't even read
the chip-id correctly at this frequency.
45 MHz however works reliable.
Signed-off-by: David Bauer <mail@david-bauer.net>
When a target configuration has unser Kconfig symbols, the build will
fail when OpenWrt is compiled with V=s and stdin is connected to a tty.
In case OpenWrt is compiled without either of these preconditions, the
build will uscceed with the symbols in question being unset.
Modify the kernel configuration in a way it fails on unset symbols
regardless of the aformentioned preconditions.
Signed-off-by: David Bauer <mail@david-bauer.net>
Calling free for the OF property can result in a kernel panic, as the
buffer in question might be referenced elsewhere. Also, it is not
removed from the tree.
Always allocate a new property and updating the tree with it fixes both
issues.
Fixes commit 91a52f22a1 ("treewide: backport support for nvmem on non platform devices")
Signed-off-by: David Bauer <mail@david-bauer.net>
The EXT4 driver also takes care of EXT2 and EXT3 file systems.
Activating the EXT2 driver kernel config options unlocked some other
ext2 driver related options which OpenWrt did not take care of.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The change which backported the of_get_mac_address() change broke some
patches in the layerscape target so the patches did not apply any more.
This commit makes them apply again and also fixes some other problems
related to this change.
Fixes commit 91a52f22a1 ("treewide: backport support for nvmem on non platform devices")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The code from ks8851.c was moved to ks8851_common.c, so it was not
backported. This broke the compile of the omap target which uses this
driver.
Fixes commit 91a52f22a1 ("treewide: backport support for nvmem on non platform devices")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch is backported from linux-arm-kernel [1] to improve situation, when
it was reported that 1.2 GHz variant is unstable with DFS.
It waits to be accepted upstream, however, it waits for Marvell people to respond.
[1] https://patchwork.kernel.org/project/linux-arm-kernel/patch/20210630225601.6372-1-kabel@kernel.org/
Fixes: 7b868fe04a ("Revert "mvebu: 5.4 fix DVFS caused random boot crashes"")
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
Based on the discussion on the mailing list [1], the patch which was
reverted, it reverts only one patch without the subsequent ones.
This leads to the SoC scaling issue not using a CPU parent clock, but
it uses DDR clock. This is done for all variants, and it's wrong because
commits (hacks) that were using the DDR clock are no longer in the mainline kernel.
If someone has stability issues on 1.2 GHz, it should not affect all
routers (1 GHz, 800 MHz) and it should be rather consulted with guys, who are trying to
improve the situation in the kernel and not making the situation worse.
There are two solutions in cases of instability:
a) disable cpufreq
b) underclock it up to 1 GHz
This reverts commit 080a0b74e3.
[1] https://lists.openwrt.org/pipermail/openwrt-devel/2021-June/035702.html
Fixes: d379476817 ("mvebu: armada-37xx: add patch to forbid cpufreq for 1.2 GHz")
CC: Pali Rohár <pali@kernel.org>
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
This option is needed e.g. to use strongswan for IPSec.
BTW: This was the only target where this option was disabled.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
This uses "hdparm" (if present) to get the harddisk into low
power mode on NAS set-ups.
Cc: Adrian Schmutzler <mail@adrianschmutzler.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Based on the discussion on the mailing list [1], the patch which was
reverted, it reverts only one patch without the subsequent ones.
This leads to the SoC scaling issue not using a CPU parent clock, but
it uses DDR clock. This is done for all variants, and it's wrong because
commits (hacks) that were using the DDR clock are no longer in the mainline kernel.
If someone has stability issues on 1.2 GHz, it should not affect all
routers (1 GHz, 800 MHz) and it should be rather consulted with guys, who are trying to
improve the situation in the kernel and not making the situation worse.
There are two solutions in cases of instability:
a) disable cpufreq
b) underclock it up to 1 GHz
This reverts commit 080a0b74e3.
[1] https://lists.openwrt.org/pipermail/openwrt-devel/2021-June/035702.html
CC: Pali Rohár <pali@kernel.org>
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
Follow the recommendations stated in the Turris Omnia DTS for eth2:
"In case SFP module is present, U-Boot has to enable the sfp node above,
remove phy-handle property, and add managed = "in-band-status" property."
The boot script is written in a way, that it works for all U-Boot
versions deployed by the vendor so far (2015.10-rc2, 2019.07).
Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Kernel 5.4 receives a reduced set, just to make the SFP cage work.
While we are at it, move the patches accepted upstream to the 0xx series.
Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Kernel 5.10 receives the complete set of improvements from 5.11/5.12.
While we are at it, move the patches accepted upstream to the 0xx series.
Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Add the missing CONFIG_KCSAN (disabled). Found while making kernel_oldconfig on
an x86-64 subtarget.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Now that we have a generic sdcard upgrade method, which was copied from
the mvebu platform method, we can switch mvebu to the generic method.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Add a generic sdcard upgrade method instead of duplicating code in yet
another target, and add a feature flag to only install this upgrade
method in targets that set this flag. Copied from mvebu.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
kirkwood build broke due to missing include needed for ETH_ALEN.
Add patch (sent upstream as well) to address that.
Refresh patches for 5.4 and 5.10.
Fixes: 91a52f22a1 ("treewide: backport support for nvmem on non platform devices")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
As both the Mi Router 4A (100M) and the Mi Router 4C use the same
label-mac-device, the alias can be moved to the shared dtsi.
Signed-off-by: Fabian Bläse <fabian@blaese.de>
A superflus ')' character has slipped into commit 91a52f22a1. Remove it
to fix build.
Fixes: 91a52f22a1 ("treewide: backport support for nvmem on non platform devices")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
MT7622 provides are hardware RNG with upstream Linux driver. Enable
compilation of this driver to make use of the hardware RNG.
Signed-off-by: David Bauer <mail@david-bauer.net>
The GL-X300B is a industrial 4G LTE router based on the Qualcomm
QCA9531 SoC.
Specifications:
- Qualcomm QCA9531 @ 650 MHz
- 128 MB of RAM
- 16 MB of SPI NOR FLASH
- 2x 10/100 Mbps Ethernet
- 2.4GHz 802.11b/g/n
- 1x USB 2.0 (vbus driven by GPIO)
- 4x LED, driven by GPIO
- 1x button (reset)
- 1x mini pci-e slot (vcc driven by GPIO)
- RS-485 Serial Port (untested)
Flash instructions:
This firmware can be flashed using either sysupgrade from the GL.iNet
firmware or the recovery console as follows:
- Press and hold the reset button
- Connect power to the router, wait five seconds
- Manually configure 192.168.1.2/24 on your computer, connect to
192.168.1.1
- Upload the firmware image using the web interface
RS-485 serial port is untested and may depend on the following commit in
the GL.iNet repo:
202e83a32a
MAC addresses as verified by OEM firmware:
vendor OpenWrt address
WAN eth0 label
LAN eth1 label + 1
2g phy0 label + 2
The label MAC address was found in the art partition at 0x0
Based on vendor commit:
16c5708b20
Signed-off-by: John Marrett <johnf@zioncluster.ca>
Add the missing ARM_SCMI_PROTOCOL symbol. Apparently it was exposed
for 5.10.53 with a kernel dependency change.
Missing symbol observed with mediatek/7622 E8450/RT3200 router.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
The virtual cable tester depends on the netlink interface for ethtool.
Thus, enable it in the generic kernel configuration.
Signed-off-by: David Bauer <mail@david-bauer.net>
In the current state, nvmem cells are only detected on platform device.
To quickly fix the problem, we register the affected problematic driver
with the of_platform but that is more an hack than a real solution.
Backport from net-next the required patch so that nvmem can work also
with non-platform devices and rework our current patch.
Drop the mediatek and dsa workaround and rework the ath10k patches.
Rework every driver that use the of_get_mac_address api.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
bcm27xx-bcm2710 builds are stalling when compiled with V=s.
Explitily disable these unset symbols to avoid stalling
builds.
Signed-off-by: David Bauer <mail@david-bauer.net>
Fixes a unused variable warning:
drivers/of/of_net.c: In function 'of_get_mac_address_mtd':
drivers/of/of_net.c:92:19: warning: unused variable 'prop' [-Wunused-variable]
Signed-off-by: David Bauer <mail@david-bauer.net>
The 1st generation MediaTek PCIe host bridge cannot handle Message
Signaled Interrupts (MSIs). The core PCI code is not aware that MSI is
not available. This results in warnings of the form:
WARNING: CPU: 2 PID: 112 at include/linux/msi.h:219
pci_msi_setup_msi_irqs.constprop.8+0x64/0x6c
Modules linked in: ahci(+) libahci libata sd_mod scsi_mod
gpio_button_hotplug
CPU: 2 PID: 112 Comm: kmodloader Not tainted 5.10.52 #0
Hardware name: Mediatek Cortex-A7 (Device Tree)
Import patches that introduce the 'no_msi' attribute to signal missing
MSI support to the core PCI.
Refresh patches:
- 000-spi-fix-fifo.patch
- 330-mtk-bmt-support.patch
- 510-net-mediatek-add-flow-offload-for-mt7623.patch
- 601-PCI-mediatek-Use-regmap-to-get-shared-pcie-cfg-base.patch
- 610-pcie-mediatek-fix-clearing-interrupt-status.patch
- 700-net-ethernet-mtk_eth_soc-add-support-for-coherent-DM.patch
- 710-pci-pcie-mediatek-add-support-for-coherent-DMA.patch
Signed-off-by: Nick Hainke <vincent@systemli.org>
It still requires fixing PCIe support:
[ 6.644699] pcie_iproc_bcma bcma0:7: host bridge /axi@18000000/pcie@12000 ranges:
[ 6.652217] pcie_iproc_bcma bcma0:7: No bus range found for /axi@18000000/pcie@12000, using [bus 00-ff]
[ 6.661833] OF: /axi@18000000/pcie@12000: Missing device_type
[ 6.667622] pcie_iproc_bcma: probe of bcma0:7 failed with error -12
[ 6.673985] pcie_iproc_bcma bcma0:8: host bridge /axi@18000000/pcie@13000 ranges:
[ 6.681514] pcie_iproc_bcma bcma0:8: No bus range found for /axi@18000000/pcie@13000, using [bus 00-ff]
[ 6.691137] pcie_iproc_bcma: probe of bcma0:8 failed with error -12
[ 6.697522] pcie_iproc_bcma bcma0:9: host bridge /axi@18000000/pcie@14000 ranges:
[ 6.705048] pcie_iproc_bcma bcma0:9: No bus range found for /axi@18000000/pcie@14000, using [bus 00-ff]
[ 6.714669] pcie_iproc_bcma: probe of bcma0:9 failed with error -12
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The label-mac logic relies on the mac-address property of a netdev
devices of-node. However, the mac address can also be stored as a
different property or read from e.g. an mtd device.
Create this node when reading a mac-address from OF if it does not
already exist and copy the mac-address used for the device to this
property. This way, the MAC address can be accessed using procfs.
Signed-off-by: David Bauer <mail@david-bauer.net>
The LEDs for LAN1 and LAN3 were swapped. Link on port 1 would illuminate
the LED on port 3 and vice versa.
Signed-off-by: David Bauer <mail@david-bauer.net>
Without explicit configuration of these pins the ethernet as well as
status LED of the device do not work correctly.
Signed-off-by: David Bauer <mail@david-bauer.net>
This reverts commit b309248730.
This commit could create a property without allocated memory, breaking
subsequent reads over a nodes property. Also, the mac-address-increment
was not applied when reading from nvmem.
Revert this commit for now, which breaks the label-mac-address logic.
Possibly, traversing the device-tree from the netdev side is easier
anyways.
Signed-off-by: David Bauer <mail@david-bauer.net>
Specifications:
* QCA9531, 16 MiB flash (Winbond W25Q128JVSQ), 128 MiB RAM
* 802.11n 2T2R (external antennas)
* QCA9887, 802.11ac 1T1R (connected with diplexer to one of the antennas)
* 3x 10/100 LAN, 1x 10/100 WAN
* UART header with pinout printed on PCB
Installation:
* The device comes with a bootloader installed only
* The bootloader offers DHCP and is reachable at http://10.123.123.1
* Accept the agreement and flash sysupgrade.bin
* Use Firefox if flashing does not work
TFTP recovery with static IP:
* Rename sysupgrade.bin to jt-or750i_firmware.bin
* Offer it via TFTP server at 192.168.0.66
* Keep the reset button pressed for 4 seconds after connecting power
TFTP recovery with dynamic IP:
* Rename sysupgrade.bin to jt-or750i_firmware.bin
* Offer it via TFTP server with a DHCP server running at the same address
* Keep the reset button pressed for 6 seconds after connecting power
Co-authored-by: Sebastian Schaper <openwrt@sebastianschaper.net>
Signed-off-by: Vincent Wiemann <vincent.wiemann@ironai.com>
This patch did not apply cleanly any more after support for the XTX
flash was added to the generic patches.
Fixes: 92012dd867 ("kernel: Add support for XTX XT26G02A SPI NAND")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch has been carried since introduction throughout every kernel
major bump and no one has tested if the later kernels improved the
situation. The Armada 3720 SoC can only process GbE interrupts on Core 0
and this is already limited in all stable kernels, so ditch this
workaround for 64 bit SoCs.
Ref: https://git.kernel.org/torvalds/c/cf9bf871280d
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Enable the Microsemi phy driver to support the VSC8514 QSGMII phy on the
FRWY-LS1046A board.
Otherwise, the "Generic PHY" driver is used.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
commit 2c2d77bd3b ("layerscape: add FRWY-LS1046A board support")
missed to add an entry to the 79_move_config preinit script.
Therefore, the config transfer on sysupgrade wass broken for this device.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
This reverts commit b7ee0786b5.
With the previous commit "realtek: remove rtl83xx vlan 1 special cases"
this is no longer required.
Signed-off-by: Thomas Nixon <tom@tomn.co.uk>
On reset, the PVID of all ports is set to 1; if this is reset to 0,
the special cases for VLAN 1 are no longer required.
port_vlan_add is called with vid=0 when the DSA port interfaces are
enabled with no VLAN; previously the VLAN was not configured in this
case, relying on VLAN 1 being present, but with the PVID set to 0,
configuring VLAN 0 as normal works as expected.
Signed-off-by: Thomas Nixon <tom@tomn.co.uk>
Add CONFIG_HAVE_ARM_ARCH_TIMER (disabled). A make kernel_oldconfig on cortexa9
will otherwise prompt for its selection. The 5.4 configuration already contains
the same symbol.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Add the new CONFIG_BATTERY_RT5033 to the generic configuration, as reported by
Paul Blazejowski. Resort the kconfig while at it.
No deleted or manually refreshed patches.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Adds support for GPON SFP modules based on the Realtek RTL8672 and
RTL9601C chips, including but not limited to:
* V-SOL V2801F
* C-Data FD511GX-RM0
* OPTON GP801R
* BAUDCOM BD-1234-SFM
* CPGOS03-0490 v2.0
* Ubiquiti U-Fiber Instant
* EXOT EGS1
Signed-off-by: Vladimir Markovets <abam_a@yahoo.com>
Latest binutils (2.37) exposed a long-standing bug. The kernel linking stage
would break at the SORTTAB step, due to the exception table having been
previously purged from vmlinux, as its section wasn't marked as unconditionally
kept. Fix thusly.
Additionally, the "#define ARM_MMU_DISCARD(x) KEEP(x)" change is bogus. It
would only apply to !CONFIG_MMU devices (which we don't support in OpenWrt), and
it would even break the build if referenced. Drop it.
While at it, rename the patch in order to make it obvious that it's
arm-specific.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
[Add same changes for kernel 5.4 too]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
