Allows proper usage of the ss tool. Otherwise, several errors and bad
data gets thrown:
Cannot open netlink socket: Protocol not supported
Cannot open netlink socket: Protocol not supported
Cannot open netlink socket: Protocol not supported
Cannot open netlink socket: Protocol not supported
Cannot open netlink socket: Protocol not supported
Cannot open netlink socket: Protocol not supported
Cannot open netlink socket: Protocol not supported
Originally reported here: https://github.com/openwrt/packages/issues/8232
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Buffalo WSR-2533DHPL is a 2.4/5 GHz band 11ac router, based on MediaTek
MT7621A.
Specification:
- SoC : MediaTek MT7621A
- RAM : DDR3 128 MiB
- Flash : SPI-NOR 16 MiB
- WLAN : 2.4/5 GHz 4T4R (2x MediaTek MT7615N)
- Ethernet : 10/100/1000 Mbps
- Switch : MediaTek MT7530 (SoC)
- LED/keys : 8x/6x (3x buttons, 2x slide-switches)
- UART : through-hole on PCB
- J4: 3.3V, GND, TX, RX from triangle-mark
- 57600n8
- Power : 12VDC 1.5A
Flash instruction using initramfs image:
1. prepare the TFTP server with the initramfs image renamed to
"linux.trx-recovery" and IP address "192.168.11.2"
2. press the "AOSS" button while powering on the WSR-2533DHPL
3. after 10 seconds, release the "AOSS" button, WSR-2533DHPL downloads
the initramfs image and boot with it automatically
4. on the initramfs image, download the sysupgrade image to the device
and perform sysupgrade with it
5. wait ~120 seconds to complete flashing
Switch position overview:
- slide-switch1 (2x positions)
- "AUTO"
- "MANUAL" (not connected to gpio)
- slide-switch2 (3x positions)
- "ROUTER"
- "AP" (not connected to gpio)
- "WB"
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[add note on switches, fix group->groups for state_default]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This prepares support for models XAP-1610 and XWR-3150. Flashing
requires using Luxul firmware version:
1) 8.1.0 or newer for XAP-1610
2) 6.4.0 or newer for XWR-3150
and uploading firmware using "Firmware Update" web UI page.
Signed-off-by: Dan Haab <dan.haab@legrand.com>
Specifications:
Qualcomm/Atheros QCA9531 + QCA9886
2x 10/100 Mbps Ethernet, with 48v PoE
2T2R 2.4 GHz, 802.11b/g/n
2T2R 5 GHz, 802.11a/n/ac
128MB RAM
16MB SPI Flash
4x LED (Always On Power, LAN, WAN, WLAN)
Flashing Instructions:
Original firmware is based on OpenWRT, so flashing the sysupgrade image on
the factory firmware is sufficient.
Tested: Reset button, WAN LED, LAN LED, Power LED (always on, not much
to test), WLAN LED (one LED only for 2 interfaces, by default it gets
assigned to the first interface), MAC addresses (match factory firmware).
My LAN factory MAC address ends in F2.
use stock_mac art_loc
lan :f2 0x0
wan :f3 0x1002
5g :f4 0x6
2g :f5 0x5006
Since MAC address flash locations do not really match their use in vendor
firmware (e.g. address from 5 GHz calibration data is assigned to 2.4 GHz
WiFi), just calculate the MAC addresses with an offset based on 0x0 address.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
[add MAC address comment]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Use upstream latest git HEAD as it allows to remove the patches
700-radius-Prevent-buffer-overflow-in-rc_mksid,
701-pppd-Fix-bounds-check-in-EAP-code and
702-pppd-Ignore-received-EAP-messages-when-not-doing-EAP and
take in other fixes.
41a7323 pppd: Fixed spelling 'unkown' => 'unknown' (#141)
6b014be pppd: Print version information to stdout instead of stderr (#133)
cba2736 pppd: Add RFC1990 (Multilink) to the See Also section of the man page
f2f9554 pppd: Add mppe.h to the list of headers to install if MPPE is defined
ae54fcf pppd: Obfuscate password argument string
8d45443 pppd: Ignore received EAP messages when not doing EAP
8d7970b pppd: Fix bounds check in EAP code
858976b radius: Prevent buffer overflow in rc_mksid()
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Remove libressl patches; they are no longer needed as LibreSSl adde
support
Replace qt tests patch with one that disables all of them.
Refresh remaining one.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
This changes the node names for the LEDs in the Netgear R6120
device-tree file to provide consistency with other devices.
Signed-off-by: Alex Lewontin <alex.c.lewontin@gmail.com>
[improve commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The mlk5 kmod lacks all necessary build symbols
for kernel 4.14 (again).
Add missing symbols to avoid build failure on these targets.
Signed-off-by: Tan Zien <nabsdh9@gmail.com>
[rewrite commit message - reorder symbols]
Signed-off-by: David Bauer <mail@david-bauer.net>
This adds support for the TP-Link TL-MR3420 v3, a later revision of the
v2 with an external gpiochip similar to TP-Link Archer C7 v4.
Specifications:
SOC: Qualcomm Atheros QCA9531
CPU: 650MHz
Flash: 4 MiB
RAM: 32 MiB
WLAN: Qualcomm Atheros QCA9531 bgn 2T2R 2.4 GHz
Ethernet: 5 ports (100M)
Flashing instructions:
- Flash factory image from OEM WebUI:
openwrt-ath79-tiny-tplink_tl-mr3420-v3-squashfs-factory.bin
- Sysupgrade from ath79 image:
openwrt-ath79-tiny-tplink_tl-mr3420-v3-squashfs-sysupgrade.bin
Signed-off-by: Lim Guo Wei <limguowei@gmail.com>
[remove SUPPORTED devices, some typo adjustments, fix WAN MAC
address, fix sorting in 01_leds]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Bump to 2.81rc5 and re-work ipset-remove-old-kernel-support.
More runtime kernel version checking is done in 2.81rc5 in various parts
of the code, so expand the ipset patch' scope to inlude those new areas
and rename to something a bit more generic.:wq
Upstream changes from rc4
532246f Tweak to DNSSEC logging.
8caf3d7 Fix rare problem allocating frec for DNSSEC.
d162bee Allow overriding of ubus service name.
b43585c Fix nameserver list in auth mode.
3f60ecd Fixed resource leak on ubus_init failure.
0506a5e Handle old kernels that don't do NETLINK_NO_ENOBUFS.
e7ee1aa Extend stop-dns-rebind to reject IPv6 LL and ULA addresses. We also reject the loopback address if rebind-localhost-ok is NOT set.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
This target has been on kernel 4.19 for several months [1] and
already uses kernel 5.4 as testing kernel. Therefore, it should
not be necessary to keep support for kernel 4.14 as well.
[1] 2a82e0e1ca ("ipq806x: switch to 4.19 kernel version")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [ipq8065/nbg6817]
201e359 Handle early exit when addrstring isn't set
fa4c464 Improve address logging on early exit messages (#83)
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
It seemed very confusing when trying to select the different variants of
hostapd which are somewhat scattered about under the menu 'Network'.
Moving all hostapd variants under a common submenu helps avoid
confusion.
Inspired-by: Kevin Mahoney <kevin.mahoney@zenotec.net>
[Fixup badly formatted patch, change menu name]
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
ab7a39a umdns: fix unused error
45c4953 dns: explicitly endian-convert all fields in header and question
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
This reverts commit d7f21940bc.
Winbond W25Q256FV and W25Q256JV both uses 0xef4019 as JEDEC ID,
but only the latter has proper 4B_OPCODES support.
W25Q256FV has all 4B read instructions but it lacks a 4B page program
instruction, causing the entire flash to be read-only.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Missing config symbols could lead to build failures on kernel
4.14/4.19.
Signed-off-by: Tan Zien <nabsdh9@gmail.com>
[rephrase commit message - reorder symbols]
Signed-off-by: David Bauer <mail@david-bauer.net>
gcc 8 & 9 appear to be more picky with regards access alignment to
packed structures, leading to this warning in dns.c:
dns.c:261:2: error: converting a packed ‘struct dns_question’ pointer
(alignment 1) to a ‘uint16_t’ {aka ‘short unsigned int’} pointer
(alignment 2) may result in an unaligned pointer value
[-Werror=address-of-packed-member]
261 | uint16_t *swap = (uint16_t *) q;
Work around what I think is a false positive by turning the warning off.
Not ideal, but not quite as not ideal as build failure.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Reduce unnecessary flash wear and be tidy:
- Run the extraction only if necessary
- Extract temporary file to /tmp
- cleanup after execution
Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
In RTL8367B (RTL8367RB/RTL8367R-VB), the driver in GPL tars of the
devices with this switch directly uses the ID of external interface
as a bit offset.
We should use the same way.
ref (RTL8367B):
- ASUS RT-N56U
- TP-Link Archer C2 v1
ref (RTL8367):
- TP-Link TL-WR2543ND v1
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
DSA requires master netdev to be up before any of its slave ports.
Bring it up during preinit so that the first lan port can be used
on failsafe.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
It's unknown which switch port is used on mikrotik_rbm11g.
Disable this image until someone with actual device fixes this problem.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
This script isn't suitable for mt7621 anymore due to switching to DSA
and it needs a different preinit script.
Generic preinit logic in package/base-files has the ability to parse
board.json and pick preinit iface accordingly. Just remove this script
instead of moving it into subtargets.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
The 2nd gmac of mediatek soc ethernet may not be connected to a PHY
and a phy-handle isn't always available.
Unfortunately, mt7530 dsa driver assumes that the 2nd gmac is always
connected to switch port 5 and setup mt7530 according to phy address
of 2nd gmac node, causing null pointer dereferencing when phy-handle
isn't defined in dts.
This commit fix this setup code by checking return value of
of_parse_phandle before using it.
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
LAN ports of MTC WR1201 are reversed, so correct their names
Signed-off-by: René van Dorst <opensource@vdorst.com>
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
mt7621 SoC has its own 'ralink_soc_info' structure with some
information about the soc itself. Pcie controller and pcie phy
drivers for this soc which are still in staging git tree make uses
of 'soc_device_attribute' looking for revision 'E2' in order to
know if reset lines are or not inverted. This way of doing things
seems to be necessary in order to make things clean and properly.
Hence, introduce this 'soc_device' to be able to properly use those
attributes in drivers. Also set 'data' pointer points to the struct
'ralink_soc_info' to be able to export also current soc information
using this mechanism.
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
The original idea of bitbanged I2C is to use i2c-gpio-custom
Since i2c-gpio-custom is no longer available on 5.4, use SoC I2C instead
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
The name of each user port should be eth0..4, instead of lan1..4
and there is no WAN port. Rename them to match the official firmware.
To avoid conflict with the master port (gmac0), rename it to "dsa".
The official firmware assigns MAC address in this way:
eth0 = label mac
eth1 = label mac + 1
...
eth4 = label mac + 4
Since we have switched to DSA, it's possible to use different MAC for each port.
Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
