In preparation for H6 support (which requires a separate ATF blob), add
an envvar to the A64 boards specifying which ATF blob to use.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
valgrind does not compile any more when using a GCC 10 for MIPS with
soft float. Just remove the parts which are generating assembler which
would not work.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Default to U-Boot env in UBI if root device is not mmc block device.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
Some of bpi-r64 boards have serial NAND attached to SPI bus.
Build U-Boot for booting from SPI-NAND.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
Use generic functions to get env partition.
Fixes: 7043e4334f ("mediatek: mt7622: improve sysupgrade on MMC")
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
The can-dev.ko kernel module was moved in kernel 5.4.110 and 5.10.28.
Fixes: a1311df95587 ("kernel: bump 5.10 to 5.10.28")
Fixes: b0a34e886d ("kernel: bump 5.4 to 5.4.110")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Looks like 'openat', 'pipe2' and 'ppoll' are now needed, possibly due
to changes on libraries used by umdns now using slightly different
calls.
Found using
/etc/init.d/umdns trace
now use umdns, ie. cover all ubus call etc., then
/etc/init.d/umdns stop
find list of syscalls traced in /tmp/umdns.*.json
Fixes: FS#3355 ("UMDNS: does not start on master with seccomp")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Without 'BUILD_DEVICES' defined, the U-Boot related package won't be
automatically selected when building for Toradex Apalis device.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
These devices never got officially supported in the tree thus it doesn't
make much sense to waste our infrastructure resources and keep building
dedicated U-Boot images for them.
CC: Petr Štetiar <ynezz@true.cz>
CC: Luka Perkov <luka.perkov@sartura.hr>
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Acked-by: Petr Štetiar <ynezz@true.cz>
Add settings for fw_printenv/fw_setenv for the Ubiquiti UniFi 6 LR
when running OpenWrt's version of U-Boot. The settings should work
equally with the unmodified version, but that has not yet been
tested.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add U-Boot build for the Ubiquiti Networks UniFi 6 LR access point.
This allows updating the bootchain to modern ARM Trusted Firmware 2.4
and U-Boot 2021.04 while keeping as much of the existing flash layout
as possible (u-boot-env, factory and eeprom partitions are retained),
gaining robust recovery vs. production dual-boot mechanism.
Add info for the Winbond W25Q512JV SPI NOR flash used in the device
and wait for GPIOs to settle after reset before checking for reset
button.
I2C connected LED controller is not supported yet.
Writing large amounts of data to SPI flash currently doesn't work due
to watchdog timeout causing reset before data write completes.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Use bl3 size of 0xa0000 instead of 0x80000 in NOR flash.
This results in bl3 ending at 0xc0000 which is where the legacy
bootchain typically puts U-Boot environment.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
bcm4908img is a tool managing BCM4908 platform images. It's used for
creating them as well as checking, modifying and extracting data from.
It's required by both: host (for building firmware images) and target
(for sysupgrade purposes). Make it a host/target package.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Now that we can create an alternate configuration file, add two
wrapper scripts for simple access to it using the alternate
alternate application names `fw_printsys' and `fw_setsys'.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Most (all?) of the realtek devices have two u-boot config partitions
with a different set of variables in each. The U-Boot shell provides
two sets of apps to manipulate these:
printenv- print environment variables
printsys- printsys - print system information variables
saveenv - save environment variables to persistent storage
savesys - savesys - save system information variables to persistent storage
setenv - set environment variables
setsys - setsys - set system information variables
Add support for multiple ubootenv configuration types, allowing
more than one configuration file.
Section names are not suitable for naming the different
configurations since each file can be the result of multiple sections
in case of backup partitions.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Now that libcap is in OpenWrt base, we can drop our custom patch to
disable libcap support and have lldpd depend on it instead. This will
allow the monitor process to drop its privileges instead of running as
root, improving security.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Having libcap in OpenWrt base allows us to enable libcap support in
other packages in base.
In lldpd, this would allow the monitor process to drop its privileges
instead of running as root, improving security. It will also allow us to
drop our patch to disable libcap.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
This adds support for the MikroTik RouterBOARD RBD52G-5HacD2HnD-TC
(hAP ac²), a indoor dual band, dual-radio 802.11ac
wireless AP with integrated omnidirectional antennae, USB port and five
10/100/1000 Mbps Ethernet ports.
See https://mikrotik.com/product/hap_ac2 for more info.
Specifications:
- SoC: Qualcomm Atheros IPQ4018
- RAM: 128 MB
- Storage: 16 MB NOR
- Wireless:
· Built-in IPQ4018 (SoC) 802.11b/g/n 2x2:2, 2.5 dBi antennae
· Built-in IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 2.5 dBi antennae
- Ethernet: Built-in IPQ4018 (SoC, QCA8075) , 5x 1000/100/10 port,
passive PoE in
- 1x USB Type A port
Installation:
Boot the initramfs image via TFTP and then flash the sysupgrade
image using "sysupgrade -n"
Signed-off-by: Robert Marko <robimarko@gmail.com>
Now that sdcard.gz image contains everything needed to boot straight
into production image, no longer force booting into recovery image on
first boot by removing the logic which implemented that.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
f8899b9 netifd: bridge: set default value for igmp_snoop
327da98 netifd: add possibility to switch off route config
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Airtime policy configuration is extremely useful in multiple BSS scenarios.
Since nowadays most people configure both private and guest networks (at
least), it makes sense to enable it by default, except for the most limited
of the variants.
Size of the hostapd-basic-openssl binary (mipsel 24Kc -O2):
543944 bytes (airtime policy disabled)
548040 bytes (airtime policy enabled)
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Acked-by: Daniel Golle <daniel@makrotopia.org>
Since KERNEL_SWAP is only enabled by default for !SMALL_FLASH targets, we need
to check if the current kernel supports swap before trying to configure
zram-swap, as opkg can't check for kernel dependencies.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Switch to Actual Net Data Rate (ACTNDR) for speed reporting on lantiq VDSL modems
Refer to ITU-T G.997.1 chapter 7.5.2.8
Independent whether retransmission is used or not in a given transmit direction:
- In L0 state, this parameter reports the Net Data Rate (as specified in G.992.3, G.992.5 or G.993.2) at which the bearer channel is operating.
- In L2 state, the parameter contains the Net Data Rate (as specified in G.992.3, G.992.5 or G.993.2) in the previous L0 state.
Signed-off-by: Jeroen Peelaerts <jeroen.peelaerts@gmail.com>
Reviewed-by: Andre Heider <a.heider@gmail.com>
This commit adds monitoring for a couple of DSL line features that are
present in the lantiq firmware blobs.
* G.INP ON/OFF
* Trellis encoding ON/OFF
* Virtaul Noise ON/OFF
* Bitswap ON/OFF
Difference in size for ltq-vdsl-app = 1k
Difference in size for kmod-ltq-vdsl-vr9 < 1k
Reviewed-by: Andre Heider <a.heider@gmail.com>
Signed-off-by: Jeroen Peelaerts <jeroen.peelaerts@gmail.com>
If service() is called w/o parameter then the status display for services
with multiple instances is incorrect. E.g. samba4 or wpad have 2 instances.
root@OpenWrt:~# /etc/init.d/samba4 status
running
root@OpenWrt:~# /etc/init.d/wpad status
running
Before change:
/etc/init.d/samba4 enabled stopped
/etc/init.d/wpad enabled stopped
After change:
/etc/init.d/samba4 enabled running
/etc/init.d/wpad enabled running
Signed-off-by: Alexander Egorenkov <egorenar-dev@posteo.net>
Upstream iproute2 detects libbpf using a one-line $CC test-compile, which
normally ignores LDFLAGS. With NLS enabled however, LDFLAGS includes an
"rpath-link" linker option needed to resolve libintl.so. Its absence
causes both the compile and libbpf detection to fail:
ld: warning: libintl.so.8, needed by libbpf.so, not found (try using
-rpath or -rpath-link)
ld: libelf.so.1: undefined reference to `libintl_dgettext'
collect2: error: ld returned 1 exit status
Fix this by directly including $LDFLAGS in the test-compile command.
Reported-by: Ian Cooper <iancooper@hotmail.com>
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
The libbfd package definition uses $(ICONV_DEPENDS) and $(INTL_DEPENDS)
but links against neither, leading to libbfd detection failures in other
packages (e.g. bpftools) and on-target relocation problems with libintl.so:
root@OpenWrt:/# ldd /usr/lib/libbfd.so
ldd (0x77db6000)
libc.so => ldd (0x77db6000)
libgcc_s.so.1 => /lib/libgcc_s.so.1 (0x77c6d000)
Error relocating /usr/lib/libbfd.so: libintl_dgettext: symbol not found
Add NLS-conditional linking of "libintl" to fix this. Also remove libbfd
package dependency $(ICONV_DEPENDS) which is not used during building or
linking.
Tested with QEMU on malta/be32, after building all packages from binutils,
bpftools and iproute2, using different libc options musl and glibc.
Fixes: 08e8175696 ("binutils: use nls.mk to fix libbfd link errors in
other packages")
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
There is no direct linking of libintl from bpftools, only secondary linking
through libelf, so remove "-lintl" from TARGET_LDFLAGS.
Fixes: 5582fbd613 ("bpftools: support NLS, fix ppc build and update to 5.8.9")
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
973cc6c compiler: actually expand block scope fix to for/while alt syntax
97bf297 compiler: ensure that alternative if/for/while syntax has own block scope
f0e2a64 tests: add missing test case for fixed switch codegen
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Introduce cmdline_get_var() to /lib/function.sh and make use of it in
export_rootdev() in /lib/upgrade/common.sh, making the code more
simple and removing one level of indentation.
Introduce get_partition_by_name() to /lib/upgrade/common.sh which is
useful on non-EFI GPT platforms like mt7622.
Remove some dead-code while at it.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
a4355a6 firewall3: clean up the flow table detection logic
edd0dc5 firewall3: create a common helper to find strings in files
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
The terminfo is required by the popular terminal multiplexer screen and
tmux, offer it by default as the size impact is minimal with 885 Bytes.
Signed-off-by: Paul Spooren <mail@aparcar.org>
The terminfo files were all in one row which is terrible to read.
Split them over multiple lines to improve readability.
Signed-off-by: Paul Spooren <mail@aparcar.org>
This includes several improvements and fixes:
61db17e rules: fix device and chain usage for DSCP/MARK targets
7b844f4 zone: avoid duplicates in devices list
c2c72c6 firewall3: remove last remaining sprintf()
12f6f14 iptables: fix serializing multiple weekdays
00f27ab firewall3: fix duplicate defaults section detection
e8f2d8f ipsets: allow blank/commented lines with loadfile
8c2f9fa fw3: zones: limit zone names to 11 bytes
78d52a2 options: fix parsing of boolean attributes
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
This version fixes 2 security vulnerabilities, among other changes:
- CVE-2021-3450: problem with verifying a certificate chain when using
the X509_V_FLAG_X509_STRICT flag.
- CVE-2021-3449: OpenSSL TLS server may crash if sent a maliciously
crafted renegotiation ClientHello message from a client.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Building with MIPS16 was disabled in 2013 due to an issue with GCC TLS:
https://dev.archive.openwrt.org/ticket/13572. But after the problematic
GCC version was retired, this change wasn't revisited.
Re-enable MIPS16 builds to reduce average elfutils library sizes ~10%.
This was compile-tested on malta/mips32be and malta/mips32le, and linked
with iproute2 for run-testing. Package sizes follow:
Library MIPS16:=0 MIPS16:=1
------- --------- ---------
libelf1 43217 37492
libasm1 12481 11658
libdw1 229723 205793
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
NXP 74HC153 is a GPIO expander. Its original source cide sits in ar71xx
architecture tree. It has been slightly modified to get GPIO pin
configuration from the device tree rather than a MACH file.
Changes to the source file:
- Remove struct nxp_74hc153_config
- in nxp_74hc153_probe(), fetch GPIO configuration from device tree
- allow GPIO framework decide the base number by passing -1 to it
- remove support for kernel versions below 4.5.0
- add OF device compatibility string
Create a package for inclusion in image.
References: https://lore.kernel.org/linux-gpio/545111184.50061.1615922388276@ichabod.co-bxl/
Signed-off-by: Mauri Sandberg <sandberg@mailfence.com>
[added link to driver usptreaming work in progress]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Moved to packages repo because it was considered
non-essential for most router configurations.
Signed-off-by: Jan Pavlinec <jan.pavlinec@nic.cz>
[shorten commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Instead of doing uci commit and reload_config for each setting do it
only once when one of these options was changed. This should make it a
little faster when both conditions are taken.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Without this change the config is only committed, but the uhttpd daemon
is not reloaded. This reload is needed to apply the config. Without the
reload of uhttpd, the ubus server is not available over http and returns
a Error 404.
This caused problems when installing luci on the snapshots and
accessing it without reloading uhttpd.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Dependency tracking for kmod-sound-hda-core is fragile. Enabling some sound
codecs (Realtek, Conexant, Sigmatel) implicitly adds a kmod-ledtrig-audio
dependency, while an enabled kmod-ledtrig-audio can be picked up through
enabling others (e.g. kmod-sound-hda-intel), and the behaviour can change
across kernel versions.
As kmod-ledtrig-audio is under 2KB, make it an unconditional dependency.
Fixes: a374b8f190 ("kernel: 5.10: update sound modules")
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
When $(FPIC) gets expanded on the command line (for instance
when setting environment variables for libtool, configure, or
make) we can't count on it not needing quoting (i.e. it could
contain multiple flags separated with spaces).
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Now that ujail supports seccomp also on Aarch64, add missing syscall
'fstat' to the list of allowed syscalls.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Enable seccomp features on Aarch64.
3e88c6f jail/seccomp: add support for aarch64
c23d8bf trace: fix build on aarch64
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
With kernel 5.10, exfat is out of staging and in tree.
Added small hack to make it work with kernel 5.4 as well.
Added removed config options for 5.4 to generic config.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
[Set CONFIG_EXFAT_ config options to default values]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This change was investigated previously [1] but not deemed necessary. With
the recent addition [2] of modern BPF loader support, however, tc gained
dependencies on libelf and libbpf, with a larger installation footprint.
Similar to ip-tiny/ip-full, split tc into tc-full and tc-tiny variants,
where the latter excludes the eBPF loader, uses a smaller executable, and
avoids libelf and libbpf package dependencies. Both variants provide the
'tc' virtual package, with tc-tiny as the default.
The previous tc package included a loadable module for iptables actions.
Separate this out into a common package, tc-mod-iptables, which both
variants depend on. Some package sizes on mips_24kc:
Before:
148343 tc_5.11.0-1_mips_24kc.ipk
After:
144833 tc-full_5.11.0-2_mips_24kc.ipk
138430 tc-tiny_5.11.0-2_mips_24kc.ipk (and no libelf or libbpf)
4115 tc-mod-iptables_5.11.0-2_mips_24kc.ipk
Also fix up some Makefile indentation.
[1] https://github.com/openwrt/openwrt/pull/1627#issuecomment-447619962
[2] b048a305a3 ("iproute2: update to 5.11.0")
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
The link equalizer sch_teql.ko of package kmod-sched relies on a hotplug
script historically included in iproute2's tc package. In previous
discussion [1], consensus was the hotplug script is best located together
with the module in kmod-sched, but this change was deferred at the time.
Relocate the hotplug script now. This change also simplifies adding a tc
variant for minimal size with reduced functionality.
[1] https://github.com/openwrt/openwrt/pull/1627#issuecomment-447923636
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
This patch has been submitted upstream to fix an error reported by a few
users. One instance seen using gcc 10.2.0, binutils 2.35.1 and musl 1.1.24:
bpf_glue.c: In function 'get_libbpf_version':
bpf_glue.c:46:11: error: 'PATH_MAX' undeclared (first use in this function);
did you mean 'AF_MAX'?
46 | char buf[PATH_MAX], *s;
| ^~~~~~~~
| AF_MAX
Reported-by: Rui Salvaterra <rsalvaterra@gmail.com>
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Update file paths for kmod-sound-hda-intel and reflect new dependency of
kmod-sound-hda-core on kmod-ledtrig-audio.
Reported-by: Javier Marcet <javier@marcet.info>
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Add conditional dependency on kmod-of-mdio due to mdio_devres.c code:
#if IS_ENABLED(CONFIG_OF_MDIO)
...
EXPORT_SYMBOL(devm_of_mdiobus_register);
#endif /* CONFIG_OF_MDIO */
Fixes: 95a3741d17 ("kernel: support new mdio_devres.ko module in 5.10")
Reported-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
kdump was removed in 7acd257ae67b4ca94f8c23cb8bda0ee0709b9216
gdb can be used as an alternative.
Remove autoreconf. It's not needed as the configure files are already
generated.
Remove upstreamed patch.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
If the environment variable FILTER is set before compilation,
compilation of the ppp-package will fail with the error message
Package ppp is missing dependencies for the following libraries:
libpcap.so.1
The reason is that the OpenWrt-patch for the Makefile only comments
out the line FILTER=y. Hence the pcap-library will be dynamically
linked if the environment variable FILTER is set elsewhere, which
causes compilation to fail. The fix consists on explicitly unsetting
the variable FILTER instead.
Signed-off-by: Eike Ritter <git@rittere.co.uk>
This fixes writing to the U-Boot environment by making the partition
writable and setting the correct flash sector size of 128K.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Allow selecting either SATA or PCIE functionality using uImage.FIT
configurations and device-tree overlays.
By default, PCIE1 is selected (as it has been before this change).
To select SATA instead, you can do this now:
fw_setenv bootconf config-mt7622-bananapi-bpi-r64-sata
and reboot.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Commit b5b0796a13 added an uint32_t to mtd.h without including stdint, which
results in a compilation error for those files not including stdint.h.
In file included from imagetag.c:36:
mtd.h:15:8: error: unknown type name 'uint32_t'
extern uint32_t opt_trxmagic;
^~~~~~~~
imagetag.c: In function 'trx_fixup':
imagetag.c:180:10: warning: unused variable 'res' [-Wunused-variable]
ssize_t res;
^~~
imagetag.c:177:14: warning: unused variable 'scan' [-Wunused-variable]
void *ptr, *scan;
^~~~
imagetag.c: In function 'trx_check':
imagetag.c:246:27: warning: initialization discards 'const' qualifier from pointer target type [-Wdiscarded-qualifiers]
struct bcm_tag *tag = (const struct bcm_tag *) buf;
^
make[3]: *** [<builtin>: imagetag.o] Error 1
Fixes: b5b0796a13 ("mtd: add option for TRX magic to fixtrx")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This release of Mbed TLS provides bug fixes and minor enhancements. This
release includes fixes for security issues.
Security fixes:
* Fix a buffer overflow in mbedtls_mpi_sub_abs()
* Fix an errorneous estimation for an internal buffer in
mbedtls_pk_write_key_pem()
* Fix a stack buffer overflow with mbedtls_net_poll() and
mbedtls_net_recv_timeout()
* Guard against strong local side channel attack against base64 tables
by making access aceess to them use constant flow code
Full release announcement:
https://github.com/ARMmbed/mbedtls/releases/tag/v2.16.10
Signed-off-by: Magnus Kroken <mkroken@gmail.com>
This adds support for the Buffalo WSR-2533DHP2.
The device uses the Broadcom TRX image format with a special magic. To
be able to boot the images or load them they have to be wrapped with
different headers depending how it is loaded.
There are multiple ways to install OpenWrt on this device.
Boot ramdisk from U-Boot
----------------------------
This will load the image and not write it into the flash.
1. Stop boot menu with "space" key
2. Select "System Load Linux to SDRAM via TFTP."
3. Load this image:
openwrt-mediatek-mt7622-buffalo_wsr-2533dhp2-initramfs-kernel.bin
4. The system boots the image
Write to flash from U-Boot
-----------------------------
This will load the image over tftp and directly write it into the flash.
1. Stop boot menu with "space" key
2. Select "System Load Linux Kernel then write to Flash via TFTP."
3. Load this image:
openwrt-mediatek-mt7622-buffalo_wsr-2533dhp2-squashfs-factory-uboot.bin
4. The system writes this image into the flash and boots into it.
Write to flash from Web UI
-----------------------------
This will load the image over over the Web UI and write it into the flash
1. Open the Web UI
2. Go to "管理" -> "ファームウェア更新"
3. Select "ローカルファイル指定" and click "更新実行"
4. Load this image:
openwrt-mediatek-mt7622-buffalo_wsr-2533dhp2-squashfs-factory.bin
5. The system writes this image into the flash and boots into it.
Specifications
-------------------
* SoC: MT7622 (4x4 2.4 GHz Wifi)
* Wifi: MT7615 (4x4 5 GHz Wifi)
* Flash: Winbond W29N01HZ 128MB SLC NAND
* RAM 256MB
* Ethernet: Realtek RTL8367S (5 x 1GBit/s, SoC via 2.5GBit/s)
Co-Developed-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Buffalo uses the TRX header with a different magic and even changes this
magic with different devices. This change allows to specify the header
to use as a command line argument.
This is needed for the Buffalo WSR-2533DHP2 based on mt7622.
Co-Developed-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Make installation to eMMC more convenient on the BPi-R64 by also
copying the production image (if valid) from SD Card to eMMC.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Instead of building all U-Boot variants by default, build only those
needed by the selected board(s).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add kmod-mdio-devres package and kernel config symbol, and update related
kmod-r8169 and kmod-ixgbe package dependencies.
Build tested module dependencies on x86/64 with CONFIG_ALL_KMODS=y.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
The ZyXEL GS1900-8 is a 8 port switch without any PoE functionality or
SFP ports, but otherwise similar to the other GS1900 switches.
Specifications
--------------
* Device: ZyXEL GS1900-8 v1.2
* SoC: Realtek RTL8380M 500 MHz MIPS 4KEc
* Flash: Macronix MX25L12835F 16 MiB
* RAM: Nanya NT5TU128M8GE-AC 128 MiB DDR2 SDRAM
* Ethernet: 8x 10/100/1000 Mbit
* LEDs: 1 PWR LED (green, not configurable)
1 SYS LED (green, configurable)
8 ethernet port status LEDs (green, SoC controlled)
* Buttons: 1 on-off glide switch at the back (not configurable)
1 reset button at the right side, behind the air-vent
(not configurable)
1 reset button on front panel (configurable)
* Power 12V 1A barrel connector
* UART: 1 serial header (JP2) with populated standard pin connector on
the left side of the PCB, towards the back. Pins are labelled:
+ VCC (3.3V)
+ TX (really RX)
+ RX (really TX)
+ GND
the labelling is done from the usb2serial connector's point of
view, so RX/ TX are mixed up.
Serial connection parameters for both devices: 115200 8N1.
Installation
------------
Instructions are identical to those for the GS1900-10HP and GS1900-8HP.
* Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10).
* Set up a TFTP server on your client and make it serve the initramfs
image.
* Connect serial, power up the switch, interrupt U-boot by hitting the
space bar, and enable the network:
> rtk network on
* Since the GS1900-10HP is a dual-partition device, you want to keep the
OEM firmware on the backup partition for the time being. OpenWrt can
only boot off the first partition anyway (hardcoded in the DTS). To
make sure we are manipulating the first partition, issue the following
commands:
> setsys bootpartition 0
> savesys
* Download the image onto the device and boot from it:
> tftpboot 0x84f00000 192.168.1.10:openwrt-realtek-generic-zyxel_gs1900-8-initramfs-kernel.bin
> bootm
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade /tmp/openwrt-realtek-generic-zyxel_gs1900-8-squashfs-sysupgrade.bin
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
3d7da7a igmpproxy tidy some loose ends
c84ba0f rcigmpproxy: add entries to /etc when creating /etc/igmpproxy.conf
5a18967 adds igmpproxy skeleton
7e6a218 logread: support resolving dns names
e39ca8b netifd: add support for /etc/udhcpc.user
7952bd0 odhcp6c: support /etc/odhcp6c.user
ba0eb4e swconfig, fwenv, agent
4556b8a pppd cosmetic
9324d9d pppd: sends AT commands to model using /dev/ttyUSBN
417b14a ttydev: add some more ttyUSB
ed739dc example: dont depend on policycoreutils
97613f9 dropbear: using dropbear as scp: dns name resolving
12c193b dropbear tcp connect ssh ports for scp
c050077 rcdnsmasq: remove redundant rule and make rcsysntpd optional
8c5de35 this is a bug
8d5c463 uhttpd rcboot rcdnsmasq
094266e hostapd and wpa_supplicant
aef0bd7 mountroot: maintains /tmp/sysupgrade.tar
24f0406 dropbear: allow it to read tmp.fs files
2901433 firstboot mkfsf2fs rcboot
2c4afb7 blockmount mmc
465ca98 adds industrial i/o (iio) nodedev
82f686e mtd stordev: back that ubiblock0_4p1 up with a filecon
7df78bd ubus: "support" older ubusd versions that run as root
4458bce swconfig: allow using terminal (to print output)
e8d606d sslcert: openssl linked: this shaves off 200 bytes
93afffb jshn ntpdhotplug
0b847f0 wpad: reads /etc/ssl/openssl.cnf
f14ee34 indent fix
a0c7cad mtd, uhttpd, ubus and ntpdhotplug
d74f98f adds a not about checkreqprot requirement in some scenarios
affacce example: add policycoreutils-setfiles for make check
4f944dc kmodloader and fwenv:
efe36a3 netifd: adds a comment/reminder
581b087 more fw_printenv loose ends
30177a4 fw_setenv: needs mtd write access to set and delete env
da28f4c fw_printenv: some minor clean ups
a062053 fw_printenv missing rules
244ba5f blockmount: extroot and /rwm
0745a6a squid: allow squid to run sslcrtd with domain transition
b851df6 squid fix
8c55acd squid: adds certfile and allow connect http but...
b7c1f6d Makefile: exclude tinyproxy from mintesttgt (using squid)
5ff39bd squid: forgot about luci
5366c97 squid/rcsquid some basic fill in
8743da6 squid skeleton
687a43b adds squid 3128 port to httpproxy port
Signed-off-by: Dominick Grift <dominick.grift@defensec.nl>
Commit f4da28c301 ("elfutils: Add host build") supplied a libelf host
library to fix a glib2 host build error, but this need was later removed
by b6212c8769 ("glib2: don't use libelf during host build").
More importantly, there are already two sources for libelf host libraries:
OpenWRT build prerequisites [1] and tools/libelf. A third is not needed.
Ref [1]: https://openwrt.org/docs/guide-developer/build-system/install-buildsystem#prerequisites
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Import patch form Frank Wunderlich <frank-w@public-files.de> to fix
build of MediaTek AHCI SATA driver.
Enable that driver on Bananapi BPi-R64.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[ -d /sys/module/xfrm_interface ] is enough to check if
CONFIG_XFRM_INTERFACE support was enabled in kernel.
Signed-off-by: Alin Nastac <alin.nastac@technicolor.com>
Copy patch added to uboot-sunxi by commit 3cc57ba462
("uboot-sunxi: add missing type __u64") also to uboot-mediatek.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* make sure USB 2.0 works (useful for UEFI-booting eg. memtest86)
* include more useful U-Boot config options on BPi-R64.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
MediaTek published their current U-Boot patchset on github:
https://github.com/mtk-openwrt/u-boot/commits/mtksoc
Import the platform patches from there (`00-mtk-*.patch`), arrange,
them nicely, drop no longer needed local patches and rebase on top of
U-Boot 2021.04-rc3.
Tested and works well on Linksys E8450 (snand-1ddr) as well as
Bananapi BPi-R64 (sdmmc-2ddr, emmc-2ddr).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Most prominently this adds changes which allow replacing the binary-
only 'bromimage' tool by U-Boot's 'mkimage' (see previous commit).
This fixes build on non-Linux and/or non-x86 platforms.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add patches for mkimage to allow using it instead of the binary-only
'bromimage' tool to generate bl2 for MT7622.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
d3f2041 uci: manually clear uci_ptr flags after uci_delete() operations
ccb7517 sys: packagelist: drop ABI version from package name
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Document the existence of this feature. This allows the user to execute a script
at each DHCPv4 event. This is useful, for example, as an ad-hoc way to update a
DDNS entry when (and only when) required.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Document the existence of this feature. This allows the user to execute a script
at each DHCPv6 event. This is useful, for example, as an ad-hoc way to update a
DDNS entry when (and only when) required.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
d464187c policycoreutils: sestatus belongs to bin not sbin
d59932a7 policycoreutils: Resolve path in restorecon_xattr
5682c0d5 policycoreutils/fixfiles.8: add missing file systems and merge check and verify
57dd1f65 policycoreutils/setfiles: Drop unused nerr variable
be7f54cb setfiles: drop ABORT_ON_ERRORS and related code
9207823c setfiles: Do not abort on labeling error
c064d214 selinux_config(5): add a note that runtime disable is deprecated
8bc865e1 newrole: support cross-compilation with PAM and audit
ba2d6c10 fixfiles: correctly restore context of mountpoints
Signed-off-by: Dominick Grift <dominick.grift@defensec.nl>
142826a3 libselinux: fix segfault in add_xattr_entry()
398d2cee libselinux: rename gettid() to something which never conflicts with the libc
8f0f0a28 selinux(8,5): Describe fcontext regular expressions
9cc6b5cf libselinux/getconlist: report failures
156dd0de libselinux: update getseuser
e2dca5df libselinux: accept const fromcon in get_context API
da4829d0 libselinux: Always close status page fd
45b15c22 selinux(8): explain that runtime disable is deprecated
3c16aaef selinux(8): mark up SELINUX values
c2a58cc5 libselinux: LABEL_BACKEND_ANDROID add option to enable
db0f2f38 libselinux: Add build option to disable X11 backend
4a142ac4 libsepol: Bump libsepol.so version
d23342a9 libselinux: convert matchpathcon to selabel_lookup()
7ef5b185 libselinux: Change userspace AVC setenforce and policy load messages to audit format.
f5d644c7 libselinux: Add additional log callback details in man page for auditing.
075f9cfe libselinux: Fix selabel_lookup() for the root dir.
a4149e0e libselinux: Add new log callback levels for enforcing and policy load notices.
a63f93d8 libselinux: initialize last_policyload in selinux_status_open()
ef902db9 libselinux: safely access shared memory in selinux_status_updated()
9e4480b9 libselinux: Remove trailing slash on selabel_file lookups.
21fb5f20 libselinux: use full argument specifiers for security_check_context in man page
e7abd802 libselinux: fix build order
05bdc031 libselinux: use kernel status page by default
Signed-off-by: Dominick Grift <dominick.grift@defensec.nl>
a9e0004f libsepol: invalidate the pointer to the policydb if policydb_init fails
6238e025 libsepol/cil: fix NULL pointer dereference in cil_fill_ipaddr
b69d77bc libsepol/cil: handle SID without assigned context when writing policy.conf
0861c659 libsepol: Validate policydb values when reading binary policy
8f5409cf libsepol: Create function ebitmap_highest_set_bit()
0451adeb libsepol/cil: Destroy disabled optional blocks after pass is complete
32f8ed3d libsepol/cil: introduce intermediate cast to silence -Wvoid-pointer-to-enum-cast
4662bdc1 libsepol/cil: be more robust when encountering <src_info>
6b561058 libsepol/cil: fix NULL pointer dereference with empty macro argument
0d0e47c7 libsepol/cil: Fix integer overflow in the handling of hll line marks
1b36ace2 libsepol: include header files in source files when matching declarations
1f1fa9d4 libsepol: uniformize prototypes of sepol_mls_contains and sepol_mls_check
72a88d75 libsepol: remove unused files
eba0ffee libsepol/cil: Fix heap-use-after-free when using optional blockinherit
1048f8d3 libsepol/cil: unlink blockinherit->block link when destroying a block
b3202918 libsepol/cil: fix memory leak when a constraint expression is too deep
f0d98f83 libsepol/cil: Fix heap-use-after-free in __class_reset_perm_values()
5d021d66 libsepol/cil: Update symtab nprim field when adding or removing datums
34bd9a9d libsepol: destroy filename_trans list properly
bdf4e332 libsepol/cil: fix NULL pointer dereference when parsing an improper integer
b7ea65f5 libsepol/cil: destroy perm_datums when __cil_resolve_perms fails
228c06d9 libsepol/cil: fix out-of-bound read in cil_print_recursive_blockinherit
a25d9104 libsepol/cil: constify some strings
e2d01842 libsepol/cil: propagate failure of cil_fill_list()
6c8fca10 libsepol/cil: do not add a stack variable to a list
38a09b74 libsepol/cil: fix NULL pointer dereference when using an unused alias
3c357285 libsepol/cil: remove useless print statement
90809674 libsepol/cil: always destroy the lexer state
d16a1e46 libsepol/cil: Use the macro FLAVOR() whenever possible
2aac859a libsepol/cil: Use the macro NODE() whenever possible
d317b470 libsepol/cil: Remove unnecessary assignment in cil_resolve_name_keep_aliases()
9b9761cf libsepol/cil: Remove unused field from struct cil_args_resolve
e257d4c7 libsepol/cil: Get rid of unnecessary check in cil_gen_node()
ebba2b00 libsepol/cil: cil_tree_walk() helpers should use CIL_TREE_SKIP_*
89dab467 libsepol: free memory when realloc() fails
2d353bd5 libsepol/cil: Give error for more than one true or false block
4a142ac4 libsepol: Bump libsepol.so version
506c7b95 libsepol: Drop deprecated functions
ae58e84b libsepol: Get rid of the old and duplicated symbols
c97d63c6 libsepol: silence potential NULL pointer dereference warning
64387cb3 libsepol: drop confusing BUG_ON macro
521e6a2f libsepol/cil: fix signed overflow caused by using (1 << 31) - 1
a152653b libsepol/cil: Fix neverallow checking involving classmaps
734e4beb libsepol/cil: Validate conditional expressions before adding to binary policy
685f577a libsepol/cil: Validate constraint expressions before adding to binary policy
8206b8cb libsepol: implement POLICYDB_VERSION_COMP_FTRANS
42ae834a libsepol,checkpolicy: optimize storage of filename transitions
Signed-off-by: Dominick Grift <dominick.grift@defensec.nl>
945d0d7 utils: fix C style in header file
2cfc26f inittab: detect active console from kernel if no console= specified
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Fix: bpftools 5.11.2 does not compile on macOS, because the -m option
was placed between src and dst. Corrected by moving -m 644 before src.
Signed-off-by: Georgi Valkov <gvalkov@abv.bg>
The pkgconfig file hardcodes a host library directory which cannot be
overridden by OpenWrt during builds. Use SED to fix this and potential
include directory problems, as is done with several other packages.
This fixes a strange issue intermittently seen building iproute2 on the
oxnas target:
iptables modules directory: /usr/lib/iptables
libc has setns: yes
SELinux support: no
libbpf support: no
libbpf version 0.3.0 is too low, please update it to at least 0.1.0
LIBBPF_FORCE=on set, but couldn't find a usable libbpf
Fixes: 2f0d672088 ("bpftools: add utility and library packages
supporting eBPF usage")
Reported-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Make packages depending on usb-serial selective, so we do not have
to add kmod-usb-serial manually for every device.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
So far, board.d files were having execute bit set and contained a
shebang. However, they are just sourced in board_detect, with an
apparantly unnecessary check for execute permission beforehand.
Replace this check by one for existance and make the board.d files
"normal" files, as would be expected in /etc anyway.
Note:
This removes an apparantly unused '#!/bin/sh /etc/rc.common' in
target/linux/bcm47xx/base-files/etc/board.d/01_network
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Partially restore the wild-card matching for kmod-usb3 modules to fix
build on platforms without PCI which otherwise file, as seen on
buildbot:
ERROR: module '[...]/linux-5.4.102/drivers/usb/host/xhci-pci.ko' is missing.
modules/usb.mk:1675: recipe for target '[...]/kmod-usb3_5.4.102-1_mips_mips32.ipk' failed
Fixes: 7bda2e9aba ("kernel: fix kmod-usb3 dependencies")
Fixes: be23f9818a ("apm821xx: add support for kernel 5.10")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Remove unneeded delcarations form package Makefile now that everything
comes from github.com/mtk-openwrt upstream.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Adding CONFIG_USB_XHCI_PCI_RENESAS to KCONFIG made it so it was set
for all targets that included kmod-usb3, not just the intended
apm821xx/nand. xhci-pci has a dependency on xhci-pci-renesas if
CONFIG_USB_XHCI_PCI_RENESAS is set, breaking kmod-usb3 builds on
Linux 5.10 on all other targets.
Rework the dependencies by breaking out xhci-hcd, xhci-mtk, and
xhci-pci-renesas into new hidden kernel modules and setting kmod-usb3
dependencies properly.
Tested by building mt7621 and apm821xx/nand with kmod-usb3 on Linux 5.10
Fixes: be23f981 ("apm821xx: add support for kernel 5.10")
Cc: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
DDR3_FLYBY has accidentally been set also for the 1-chip variant which
lead to broken, unbootable images. Fix that.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This patch copies over refreshed patches from 5.4.
- dropped crypto patches (they got upstreamed)
- dropped renesas USB 3 firmware loader (they got upstreamed)
- NAND now needs extra device-properties for ECC settings.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* allow MAC address from U-Boot env to be inhertied
* allow eMMC installation to succeed also without recovery present
on the SD Card.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
All necessary blobs are now contained in the upstream repository, no
more wild replacing of blobs needed.
This new version also contains new storage drivers for (SPI-)NAND which
already comes with support for FM35Q1GA, so that patch can be dropped
as well.
Tested on:
* Bananapi BPi-R64
- sdmmc-2ddr
- emmc-2ddr
* Linksys E8450
- snand-1ddr
All works fine (booting Bananapi BPi-R64 from SD Card does NOT require
a signed image, so patch arm-trusted-firmware-mediatek to allow doing
that).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This will use the new application led trigger backend. For now this is
the only package that uses leds trigger in user space to configure the
kernel led triggers.
The callback script only emmits a message for now, so that this LED is now
managed by the rssileds service. Until now a generic warning was emitted that
this LED trigger is not supported. But that is not true.
-> Skipping trigger 'rssileds' for led '<name>' due to missing kernel module
I think this callback should be changed in the future to restart the
service.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
For now we have only kernel LED trigger support. With this change it is now
possible to use application triggers.
If we configure a LED with a non kernel trigger, then we check on every
restart and boot of the LED service if we have this trigger as an application
in "/usr/libexec/led-trigger". If this file with the name is found, then we
execute this to init the LED.
Possible use cases are:
- Start/Stop/Restart an application led trigger service for this led
- Init a LED that is configured by a hotplug script (VPN tunnel established)
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
stropts.h is unavailable under glibc (and unneeded when building
against glibc). Include it only if not building against glibc.
Reported-by: @DazzyWalkman
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Don't try to install files which no longer exist
Since {e,sd}mmc are now produced by ptgen they have been removed.
Fixes: 5a3562cd1d ("arm-trusted-firmware-mediatek: remove {e,sd}mmc headers")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Turned out those are simply MBR with active boot partition. And not
needed at all on emmc. Remove them as ptgen can now generate hybrid
MBR sufficient to boot MT7622 from SD Card.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Write everything needed for eMMC install into the gaps between
partitions on SD card. In that way, installation to eMMC only needs
the SD card, no additional files need to be loaded via TFTP any more.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
p2p_add_device() may remove the oldest entry if there is no room in the
peer table for a new peer. This would result in any pointer to that
removed entry becoming stale. A corner case with an invalid PD Request
frame could result in such a case ending up using (read+write) freed
memory. This could only by triggered when the peer table has reached its
maximum size and the PD Request frame is received from the P2P Device
Address of the oldest remaining entry and the frame has incorrect P2P
Device Address in the payload.
Fix this by fetching the dev pointer again after having called
p2p_add_device() so that the stale pointer cannot be used.
This fixes the following security vulnerabilities/bugs:
- CVE-2021-27803 - A vulnerability was discovered in how p2p/p2p_pd.c
in wpa_supplicant before 2.10 processes P2P (Wi-Fi Direct) provision
discovery requests. It could result in denial of service or other
impact (potentially execution of arbitrary code), for an attacker
within radio range.
Fixes: 17bef1e97a50 ("P2P: Add peer entry based on Provision Discovery Request")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Changes:
- Remove custom Build/Compile because it's no longer needed
- Remove std=gnu99 which is added automaticaly by igmpproxy if needed
- Remove -Dlog from CFLAGS because igmpproxy doesn't have log function
Signed-off-by: Jan Pavlinec <jan.pavlinec@nic.cz>
libunwind dependency check does not allow for MIPS64 arch. Add MIPS64 awareness.
libunwind seems to support MIPS64 without issues, it was limited by the dep arch
check in the Makefile.
Used to compile Suricata6/Rust locally without issue.
Signed-off-by: Donald Hoskins <grommish@gmail.com>
Non Linux systems e.g. macOS lack the __u64 type and produce build errors:
In file included from tools/aisimage.c:9:
In file included from include/image.h:19:
In file included from ./arch/arm/include/asm/byteorder.h:29:
In file included from include/linux/byteorder/little_endian.h:13:
include/linux/types.h:146:9: error: unknown type name '__u64'; did you mean '__s64'?
typedef __u64 __bitwise __le64;
Resolved by declaring __u64 in include/linux/types.h
Build tested on macOS and Ubuntu.
Signed-off-by: Georgi Valkov <gvalkov@abv.bg>
Compile and run-tested on malta/mip32be, using bpftool directly and also
libbpf (linked with tc) to inspect and load simple eBPF programs.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
The latest iproute2 version brings various improvements and fixes:
https://git.kernel.org/pub/scm/network/iproute2/iproute2.git/log/?qt=range&q=v5.10.0..v5.11.0
In particular, ip and tc now use libbpf as the standard way to load BPF
programs, rather than the old, limited custom loader. This allows more
consistent and featureful BPF program handling e.g. support for global
initialized variables.
Also fix a longstanding problem with iproute2 builds where unneeded DSO
dependencies are added to most utilities, bloating their installation
footprint. From research and testing, explicitly using a "--as-needed"
linker flag avoids the issue. Update accordingly and drop extra package
dependencies from Makefile.
Additional build and packaging updates include:
- install missing development header to iproute2/bpf_elf.h
- propagate OpenWrt verbose flag during build
- update and refresh patches
Compile and run tested: QEMU/malta-mips32be on kernels 5.4 & 5.10.
All iproute2 packages were built and installed to the test image. Some
regression testing using ip-full and tc was successfully performed to
exercise several kmods, tc modules, and simple BPF programs.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Simplify cmake option handling by putting everything in blocks.
Add openssl patch as there's no easy way to disable.
Rebase the skip manpages patch.
Remove the monitor mode patch as it no longer applies.
Remove flex patch as normal Makefile is no longer used.
Remove USB path patch. While it is deprecated, the codepath is never
taken. /sys/bus/usb/devices is checked before hand. If it exists, the
function does stuff and returns. Additionally, this path is used
elsewhere in the code.
Refresh other patches.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
NTPD in busybox has option -I to bind server to IFACE.
However, capabilities of the busybox are limited, the -I option cannot be
repeated and only one interface can be effectively specified in it.
This option is currently not configurable via UCI.
The patch adds an interface option to the system config, ntp section.
Also sort options for uci_load_validate alphabetically.
Signed-off-by: Alexey Dobrovolsky <dobrovolskiy.alexey@gmail.com>
with u-boot v2020.07 some variables have been renamed so this patch needs to be adjusted
otherwise at least with macOS as build system there are build errors
Signed-off-by: Ronny Kotzschmar <ro.ok@me.com>
The QOS feature depends on KPI2UDP which was removed from the tree with
commit a95775e4b2 ("drop unmaintained packages") in 2012.
Since QOS was the last user of the KPI, the feature can be disabled by
default.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The following warnings are shown during build:
/usr/include/vdsl/cmv_message_format.h:33:6: warning: "MEI_SUPPORT_DEBUG_STREAMS" is not defined, evaluates to 0 [-Wundef]
#if (MEI_SUPPORT_DEBUG_STREAMS == 1)
^~~~~~~~~~~~~~~~~~~~~~~~~
/usr/include/vdsl/drv_mei_cpe_interface.h:2256:6: warning: "MEI_SUPPORT_OPTIMIZED_FW_DL" is not defined, evaluates to 0 [-Wundef]
#if (MEI_SUPPORT_OPTIMIZED_FW_DL == 1)
^~~~~~~~~~~~~~~~~~~~~~~~~~~
The headers are provided by the MEI driver, but the defines are never
set by the vdsl app. While the struct with the
MEI_SUPPORT_OPTIMIZED_FW_DL conditional isn't used by the vdsl app,
however CMV_USED_PAYLOAD_8BIT_SIZE which value depends on
MEI_SUPPORT_DEBUG_STREAMS is.
Since the MEI driver doesn't provide an autogenerated header with
compile flags, the flags are hardcoded for the vdsl app.
Set them for the MEI driver as well, to indicate a relation to the
values used for the vdsl app and to be not surprised by a changed
default in case the MEI driver gets updated. Use the current default
values defined in the MEI driver.
Signed-off-by: Mathias Kresin <dev@kresin.me>
a857b45 resolv/locale: eventually this should be more efficient
11ed281 some more optimization
764a475 add redundant calls to file.search_conffile_dirs()
7d4558e fs: treat devtmpfs that same as tmpfs
81b677e adds irqbalance skeleton
5506244 irqbalance rules
cc96cd8 adds usbutil and gtpfdisk skels
01e2a55 some fsck, gptfdisk, mkfs and usbutil rules
d6d1e7d usbutil: output to terminal
da576fa fsck, gptfdisk and usbutil rules
09b39e9 unbound
241a029 hotplugcall: allow dac_read_search (is a subset of dac_override)
af0fe90 adds label for tcsh
160f79e adds tcpdump
6d02b96 adds coreutil execfile for busybox alternatives
ac54884 coreutilexecfile: these are known to require privileges, so exclude
8cb3b66 adds chrootexecfile
6d329d3 this saves 9KiB and its a bit more robust
88e2425 move addpart/delpart/partx to gptfdisk.cil
261012d ntphotplug: reads ubox data files
0473ace various
740e820 work through to genfs_seclabel_symlinks loose ends (Linux 5.10)
bef21f5 TODO adds a note about how I dont need to upgrade to polver 33 from 31
cb2e5a3 ubus uses ntpdhotplug fd, and some genfs_seclabel_symlink changes
07df9b9 luci, rpcd and wpad (mainly genfs_selabel related but not all)
8d86cab genfs_seclabel loose ends for blockmount, hotplugcall, irqbalance, zram-swap
b8156cd adds a note about how i forgot to target blockd
6e82ab8 adds blockd and related
254ff43 Makefile: exclude blockd from mintesttgt
4dc6bc2 pppd update related and unbound-odhcp rules
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Provide U-Boot variants for SD-card as well as eMMC boot, so we can
generate whole-disk images for the device.
While at it, rename 'mt7622' to 'mt7622-rfb1' to make it less confusing
now that more boards are being added.
Thanks to Frank Wunderlich (@frank-w) for making that nice SVG image
explaining the MMC boot process[1] and for providing the necessary
binary header blobs.
[1]: https://github.com/frank-w/BPI-R64-ATF
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add U-Boot environment configuration for the Linksys E8450 (UBI) to
allow access to the bootloader environment from OpenWrt via
'fw_printenv' and 'fw_setenv'.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Build U-Boot for the Linksys E8450 in order to have support for UBI.
The loader has a default environment with scripts handling the reset
button as well as fall-back to recovery firmware. If the loader comes
up without a valid environment found in UBI, it will automatically
make sure UBI is formatted and create a new environment and proceed
to load recovery firmware (either from UBI or via TFTP if recovery is
corrupted or unavailable).
If the button is held down during power-on, the yellow status LED
turns on and the bootloader environment is reset to factory defaults.
If the button is released at this point, the recovery firmware (if
existing) is loaded from UBI and booted.
If the button is continously held down even beyond the point that
the yellow LED turned on, the loader will try to load the recovery
firmware via TFTP from server 192.168.1.254, write it to UBI and
boot.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The Linksys E8450 aka. Belkin RT3200 comes with a rather fresh brand
of SPI NAND storage. Add support for it to the nandx driver in
arm-trusted-firmware-mediatek, so we can boot from that chip.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Instead of only relying in /sysupgrade.tgz being present in rootfs to
restore configuration, also grab /tmp/sysupgrade.tar which may have
magically gotten there during preinit...
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
CHACHA_MIPS depends on CPU_MIPS32_R2. Therefore,
kmod-crypto-lib-chacha20 should not contain chacha-mips.ko on MIPS32 R1
targets. Enforce that in the target-specific definition.
Fixes bcm47xx, bcm63xx, lantiq/ase, ath25 builds.
Fixes: 06351f1 ("kernel: migrate wireguard into the kernel tree")
Cc: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Reviewed-by: Jason A. Donenfeld <Jason@zx2c4.com>
To the vast majority of the users, wireguard-tools are not useful
without the underlying kernel module. The cornercase of only generating
keys and not using the secure tunnel is something that won't be done on
an embedded OpenWrt system often. On the other hand, maintaining a
separate meta-package only for this use case introduces extra
complexity. WireGuard changes for Linux 5.10 remove the meta-package.
So let's make wireguard-tools depend on kmod-wireguard
to make WireGuard easier to use without having to install multiple
packages.
Fixes: ea980fb9 ("wireguard: bump to 20191226")
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Use NETWORK_SUPPORT_MENU like all other modules in netsupport.mk. Drop
SECTION and CATEGORY fields as they are set by default and to match
other packages in netsupport.mk. Use better TITLE for kmod-wireguard
(taken from upstream drivers/net/Kconfig).
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
On Linux 5.4, build WireGuard from backports. Linux 5.10 contains
wireguard in-tree.
Add in-kernel crypto libraries required by WireGuard along with
arch-specific optimizations.
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
ZTE MF283+ is a dual-antenna LTE category 4 router, based on Ralink
RT3352 SoC, and built-in ZTE P685M PCIe MiniCard LTE modem.
Hardware highlighs:
- CPU: MIPS24KEc at 400MHz,
- RAM: 64MB DDR2,
- Flash: 16MB SPI,
- Ethernet: 4 10/100M port switch with VLAN support,
- Wireless: Dual-stream 802.11n (RT2860), with two internal antennas,
- WWAN: Built-in ZTE P685M modem, with two internal antennas and two
switching SMA connectors for external antennas,
- FXS: Single ATA, with two connectors marked PHONE1 and PHONE2,
internally wired in parallel by 0-Ohm resistors, handled entirely by
internal WWAN modem.
- USB: internal miniPCIe slot for modem,
unpopulated USB A connector on PCB.
- SIM slot for the WWAN modem.
- UART connector for the console (unpopulated) at 3.3V,
pinout: 1: VCC, 2: TXD, 3: RXD, 4: GND,
settings: 57600-8-N-1.
- LEDs: Power (fixed), WLAN, WWAN (RGB),
phone (bicolor, controlled by modem), Signal,
4 link/act LEDs for LAN1-4.
- Buttons: WPS, reset.
Installation:
As the modem is, for most of the time, provided by carriers, there is no
possibility to flash through web interface, only built-in FOTA update
and TFTP recovery are supported.
There are two installation methods:
(1) Using serial console and initramfs-kernel - recommended, as it
allows you to back up original firmware, or
(2) Using TFTP recovery - does not require disassembly.
(1) Using serial console:
To install OpenWrt, one needs to disassemble the
router and flash it via TFTP by using serial console:
- Locate unpopulated 4-pin header on the top of the board, near buttons.
- Connect UART adapter to the connector. Use 3.3V voltage level only,
omit VCC connection. Pin 1 (VCC) is marked by square pad.
- Put your initramfs-kernel image in TFTP server directory.
- Power-up the device.
- Press "1" to load initramfs image to RAM.
- Enter IP address chosen for the device (defaults to 192.168.0.1).
- Enter TFTP server IP address (defaults to 192.168.0.22).
- Enter image filename as put inside TFTP server - something short,
like firmware.bin is recommended.
- Hit enter to load the image. U-boot will store above values in
persistent environment for next installation.
- If you ever might want to return to vendor firmware,
BACK UP CONTENTS OF YOUR FLASH NOW.
For this router, commonly used by mobile networks,
plain vendor images are not officially available.
To do so, copy contents of each /dev/mtd[0-3], "firmware" - mtd3 being the
most important, and copy them over network to your PC. But in case
anything goes wrong, PLEASE do back up ALL OF THEM.
- From under OpenWrt just booted, load the sysupgrade image to tmpfs,
and execute sysupgrade.
(2) Using TFTP recovery
- Set your host IP to 192.168.0.22 - for example using:
sudo ip addr add 192.168.0.22/24 dev <interface>
- Set up a TFTP server on your machine
- Put the sysupgrade image in TFTP server root named as 'root_uImage'
(no quotes), for example using tftpd:
cp openwrt-ramips-rt305x-zte_mf283plus-squashfs-sysupgrade.bin /srv/tftp/root_uImage
- Power on the router holding BOTH Reset and WPS buttons held for around
5 seconds, until after WWAN and Signal LEDs blink.
- Wait for OpenWrt to start booting up, this should take around a
minute.
Return to original firmware:
Here, again there are two possibilities are possible, just like for
installation:
(1) Using initramfs-kernel image and serial console
(2) Using TFTP recovery
(1) Using initramfs-kernel image and serial console
- Boot OpenWrt initramfs-kernel image via TFTP the same as for
installation.
- Copy over the backed up "firmware.bin" image of "mtd3" to /tmp/
- Use "mtd write /tmp/firmware.bin /dev/mtd3", where firmware.bin is
your backup taken before OpenWrt installation, and /dev/mtd3 is the
"firmware" partition.
(2) Using TFTP recovery
- Follow the same steps as for installation, but replacing 'root_uImage'
with firmware backup you took during installation, or by vendor
firmware obtained elsewhere.
A few quirks of the device, noted from my instance:
- Wired and wireless MAC addresses written in flash are the same,
despite being in separate locations.
- Power LED is hardwired to 3.3V, so there is no status LED per se, and
WLAN LED is controlled by WLAN driver, so I had to hijack 3G/4G LED
for status - original firmware also does this in bootup.
- FXS subsystem and its LED is controlled by the
modem, so it work independently of OpenWrt.
Tested to work even before OpenWrt booted.
I managed to open up modem's shell via ADB,
and found from its kernel logs, that FXS and its LED is indeed controlled
by modem.
- While finding LEDs, I had no GPL source drop from ZTE, so I had to probe for
each and every one of them manually, so this might not be complete -
it looks like bicolor LED is used for FXS, possibly to support
dual-ported variant in other device sharing the PCB.
- Flash performance is very low, despite enabling 50MHz clock and fast
read command, due to using 4k sectors throughout the target. I decided
to keep it at the moment, to avoid breaking existing devices - I
identified one potentially affected, should this be limited to under
4MB of Flash. The difference between sysupgrade durations is whopping
3min vs 8min, so this is worth pursuing.
In vendor firmware, WWAN LED behaviour is as follows, citing the manual:
- red - no registration,
- green - 3G,
- blue - 4G.
Blinking indicates activity, so netdev trigger mapped from wwan0 to blue:wwan
looks reasonable at the moment, for full replacement, a script similar to
"rssileds" would need to be developed.
Behaviour of "Signal LED" in vendor firmware is as follows:
- Off - no signal,
- Blinking - poor coverage
- Solid - good coverage.
A few more details on the built-in LTE modem:
Modem is not fully supported upstream in Linux - only two CDC ports
(DIAG and one for QMI) probe. I sent patches upstream to add required device
IDs for full support.
The mapping of USB functions is as follows:
- CDC (QCDM) - dedicated to comunicating with proprietary Qualcomm tools.
- CDC (PCUI) - not supported by upstream 'option' driver yet. Patch
submitted upstream.
- CDC (Modem) - Exactly the same as above
- QMI - A patch is sent upstream to add device ID, with that in place,
uqmi did connect successfully, once I selected correct PDP context
type for my SIM (IPv4-only, not default IPv4v6).
- ADB - self-explanatory, one can access the ADB shell with a device ID
added to 51-android.rules like so:
SUBSYSTEM!="usb", GOTO="android_usb_rules_end"
LABEL="android_usb_rules_begin"
SUBSYSTEM=="usb", ATTR{idVendor}=="19d2", ATTR{idProduct}=="1275", ENV{adb_user}="yes"
ENV{adb_user}=="yes", MODE="0660", GROUP="plugdev", TAG+="uaccess"
LABEL="android_usb_rules_end"
While not really needed in OpenWrt, it might come useful if one decides to
move the modem to their PC to hack it further, insides seem to be pretty
interesting. ADB also works well from within OpenWrt without that. O
course it isn't needed for normal operation, so I left it out of
DEVICE_PACKAGES.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
[remove kmod-usb-ledtrig-usbport, take merged upstream patches]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
As PKG_LICENSE is originally set by include/trusted-firmware-a.mk it
can only be appended after that. Hence move that line below the
include to actually make sense.
(cosmetical change, already slipped into openwrt-21.02 branch)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This package had two patches (with two headers etc.) in one file,
which would have quilt merging them during a refresh.
Separate these patches into two files, as the original intent seems
to be having them separate.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
When using Shell arithmetric evaluation via $((..)) the variables in
the expression do not need to be prefixed by the '$' sign.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Check if firmware environment variable 'rootfs_data_max' exists and is
set to a numerical value greater than 0. If so, limit rootfs_data
volume to that size instead of using the maximum available size.
This is useful on devices with lots of flash where users may want to
have eg. a volume for persistent logs and statistics or for external
applications/containers. Persistence on rootfs overlay is limited by
the size of memory available during the sysugprade process as that
data needs to be copied to RAM while the volume is being recreated
during sysupgrade. Hence it is unsuitable for keeping larger amounts
of data accross upgrade which makes additional volume(s) for
application data desirable.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Allow for single (external-data) FIT image to hold kernel, dtb and
squashfs. In that way, the bootloader verifies the system integrity
including the rootfs, because what's the point of checking that the
hash of the kernel is correct if it won't boot in case of squashfs
being corrupted? Better allow bootloader to check everything needed
to make it at least up to failsafe mode. As a positive side effect
this change also makes the sysupgrade process on nand potentially
much easier as it is now.
In short: mkimage has a parameter '-E' which allows generating FIT
images with 'external' data rather than embedding the data into the
device-tree blob itself. In this way, the FIT structure itself remains
small and can be parsed easily (rather than having to page around
megabytes of image content). This patch makes use of that and adds
support for adding sub-images of type 'filesystem' which are used to
store the squashfs. Now U-Boot can verify the whole OS and the new
partition parsers added in the Linux kernel can detect the filesystem
sub-images, create partitions for them, and select the active rootfs
volume based on the configuration in FIT (passing configuration via
device tree could be implemented easily at a later stage).
This new FIT partition parser works for NOR flash (on top of mtdblock),
NAND flash (on top of ubiblock) as well as classic block devices
(ie. eMMC, SDcard, SATA, NVME, ...).
It could even be used to mount such FIT images via `losetup -P` on a
user PC if this patch gets included in Linux upstream one day ;)
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Upstream integrated multiple patches from Distributions and did other
changes:
* rp-pppoe.so was renamed to pppoe.so
* Converted to ANSI C
The following patches were applied upstream:
* 100-debian_ip-ip_option.patch
* 101-debian_close_dev_ppp.patch
* 103-debian_fix_link_pidfile.patch
* 106-debian_stripMSdomain.patch
* 107-debian_pppoatm_wildcard.patch
* 110-debian_defaultroute.patch
* 202-no_strip.patch
Compilation with musl libc was fixed upstream so
140-pppoe_compile_fix.patch is not needed any more
Parts of the 203-opt_flags.patch patch were applied in a different way
upstream.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The packages feed has a proposed package for a GOST engine, which needs
support from the main openssl library. It is a default option in
OpenSSL. All that needs to be done here is to not disable it.
Package increases by a net 1-byte, so it is not really really worth
keeping this optional.
This commit also includes a commented-out example engine configuration
in openssl.cnf, as it is done for other available engines.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
This adds the necessary nuts and bolts for the uboot settings for both the ZyXEL GS1900-8HP v1 and v2.
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
Biggest fix for this version is CVE-2021-3336, which has already been
applied here. There are a couple of low severity security bug fixes as
well.
Three patches are no longer needed, and were removed; the one remaining
was refreshed.
This tool shows no ABI changes:
https://abi-laboratory.pro/index.php?view=objects_report&l=wolfssl&v1=4.6.0&v2=4.7.0
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
There are efforts underway to bring wireguard in-tree for Linux 5.4 and
to have a common build infrastructure for both 5.4 and 5.10 for
kmod-wireguard[0]. Until then, restrict kmod-wireguard to build only on
Linux 5.4, because the wireguard-compat package will not build on Linux
5.10.
[0]: https://github.com/openwrt/openwrt/pull/3885
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Modify existing modules to reflect their new location in Linux 5.10. Add
missing dependenices.
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
[enable CRYPTO_USER_API_ENABLE_OBSOLETE; add kmod-crypto-hash dependency
to usb-net-rtl8152]
Signed-off-by: David Bauer <mail@david-bauer.net>
Now that mirrors have picked it up, switch to using the @OPENWRT
mirror instead of hosting those files on Github.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2be57ed cosmetics: provide compatible system info on Aarch64
37eed13 system: expose if system was booted from initramfs
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Prerequisite patch:
Correct a typo in the Changelog and clean up a stray file
Fix changes in libusb which introduced a regression:
Commit e2be556bd2 ("linux_usbfs: Parse config descriptors during device
initialization") introduced a regression for devices with multiple
configurations. The logic that verifies the reported length of the
configuration descriptors failed to count the length of the
configuration descriptor itself and would truncate the actual length by
9 bytes, leading to a parsing error for subsequent descriptors.
Signed-off-by: Georgi Valkov <gvalkov@abv.bg>
The ls-ddr-phy package needs fiptool options that are not
available via the version from arm-trusted-firmware-tools.
This breaks build for layerscape with the recently added LX2160a:
create: unrecognized option '--ddr-immem-udimm-1d'
Use the tfa-layerscape variant again for now, but rename it to
fiptool-layerscape to indicate that it's a specific variant.
This reverts 84bc7d31e0 ("tfa-layerscape: don't build fiptool").
Fixes: f59d7aab2a ("layerscape: add ddr-phy package")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This driver adds the LED support for the PC Engines APU1.
This integrates the Linux kernel driver and includes a patch to support
newer firmware versions. Also the default LED configuration is updated
to use the correct devices.
Signed-off-by: Andreas Eberlein <foodeas@aeberlein.de>
This is a backport of the upstream commit 58bbbb598144 ("nl80211: Ignore
4addr mode enabling error if it was already enabled") which fixes same
issue as in the current fix contained in '130-wpa_supplicant-multi_ap_roam.patch',
but in a different way:
nl80211_set_4addr_mode() could fail when trying to enable 4addr mode on
an interface that is in a bridge and has 4addr mode already enabled.
This operation would not have been necessary in the first place and this
failure results in disconnecting, e.g., when roaming from one backhaul
BSS to another BSS with Multi AP.
Avoid this issue by ignoring the nl80211 command failure in the case
where 4addr mode is being enabled while it has already been enabled.
Signed-off-by: Raphaël Mélotte <raphael.melotte@mind.be>
[bump PKG_RELEASE, more verbose commit description]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
OpenSSL downloads itself are distributed using Akamai CDN, so use these
sources as the highest priority.
Remove a stale mirror which seems to be offline for a longer time
already.
Add fallbacks to the old release path also for the mirrors.
Signed-off-by: David Bauer <mail@david-bauer.net>
The QorIQ LX2160A reference design board provides a comprehensive platform
that enables design and evaluation of the LX2160A processor.
- Enables network intelligence with the next generation Datapath (DPPA2)
which provides differentiated offload and a rich set of IO, including
10GE, 25GE, 40GE, and PCIe Gen4
- Delivers unprecedented efficiency and new virtualized networks
- Supports designs in 5G packet processing, network function
virtualization, storage controller, white box switching, network
interface cards, and mobile edge computing
- Supports all three LX2 family members (16-core LX2160A; 12-core LX2120A;
and 8-core LX2080A)
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
[use AUTORELEASE, add dtb to firmware part]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Add ddr-phy package for layerscape. Currently only LX2160ARDB
requires the package.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
[use AUTORELEASE]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The LS1046A Freeway board (FRWY) is a high-performance computing,
evaluation, and development platform that supports the QorIQ
LS1046A architecture processor capable of support more than 32,000
CoreMark performance. The FRWY-LS1046A board supports the QorIQ
LS1046A processor, onboard DDR4 memory, multiple Gigabit Ethernet,
USB3.0 and M2_Type_E interfaces for Wi-Fi.
The FRWY-LS1046A-TP includes the Coral Tensor Flow Processing Unit
that offloads AI/ML inferencing from the CPU to provide significant
boost for AI/ML applications. The FRWY-LS1046A-TP includes one M.2
TPU module and more modules can easily be added including USB
versions of the module to scale the AI/ML performance.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
[rebase, use AUTORELEASE, fix sorting, add dtb to firmware part]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
If an external module uses exported symbols from another external
module, Kbuild needs to have full knowledge of all symbols to
avoid spitting out warnings about undefined symbols.
Use PKG_EXTMOD_SUBDIRS to point to the build directory which contains
the Module.symvers.
Pass KERNEL_MAKE_FLAGS to the external module build, to inject
KBUILD_EXTRA_SYMBOLS. KBUILD_EXTRA_SYMBOLS holds a space separated list
of Module.symvers, which list all exported symbols.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This fixes 4 security vulnerabilities/bugs:
- CVE-2021-2839 - SSLv2 vulnerability. Openssl 1.1.1 does not support
SSLv2, but the affected functions still exist. Considered just a bug.
- CVE-2021-2840 - calls EVP_CipherUpdate, EVP_EncryptUpdate and
EVP_DecryptUpdate may overflow the output length argument in some
cases where the input length is close to the maximum permissable
length for an integer on the platform. In such cases the return value
from the function call will be 1 (indicating success), but the output
length value will be negative.
- CVE-2021-2841 - The X509_issuer_and_serial_hash() function attempts to
create a unique hash value based on the issuer and serial number data
contained within an X509 certificate. However it was failing to
correctly handle any errors that may occur while parsing the issuer
field (which might occur if the issuer field is maliciously
constructed). This may subsequently result in a NULL pointer deref and
a crash leading to a potential denial of service attack.
- Fixed SRP_Calc_client_key so that it runs in constant time. This could
be exploited in a side channel attack to recover the password.
The 3 CVEs above are currently awaiting analysis.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Add m4 patch to avoid conflict with tools/autoconf-archive.
Add build parallel as it seems to work now.
Remove a bunch of uClibc-ng hacks as it is not in the tree anymore.
Format security patch was fixed upstream.
Refreshed other patches.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
After the ABI version rework, packages need to be declared in the order of
their dependencies, so that dependent packages will use the right ABI version
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Let's switch to 5.10 now that mac80211 has been updated.
Runtime-tested on ipq806x (Netgear R7800).
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
After the ABI version rework, packages need to be declared in the order of
their dependencies, so that dependent packages will use the right ABI version
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Automatically setup dhcpv4 server just like it's done for dhcpv6.
To select whether odhcpd or dnsmasq are serving DHCPv4 requests there
still is the 'maindhcp' option. To make things less confusing, make
sure things really work out-of-the-box in case dnsmasq is not even
installed at the time the uci-defaults script is being run.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This fixes the build on MIPS BE like ath25 and ath79 target.
We get this error message when linking libwolfssl:
mips-openwrt-linux-musl/bin/ld: /home/hauke/openwrt/openwrt/staging_dir/target-mips_mips32_musl/usr/lib/libwolfssl.so: unknown type [0x7000002a] section `.MIPS.abiflags'
mips-openwrt-linux-musl/bin/ld: /home/hauke/openwrt/openwrt/staging_dir/target-mips_mips32_musl/usr/lib/libwolfssl.so: unknown type [0x7000002a] section `.MIPS.abiflags'
mips-openwrt-linux-musl/bin/ld: skipping incompatible /home/hauke/openwrt/openwrt/staging_dir/target-mips_mips32_musl/usr/lib/libwolfssl.so when searching for -lwolfssl
mips-openwrt-linux-musl/bin/ld: cannot find -lwolfssl
collect2: error: ld returned 1 exit status
This reverts commit 2591c83b34.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This fixes the build on MIPS BE like ath25 and ath79 target.
We get this error message when linking libubox:
mips-openwrt-linux-musl/bin/ld: /home/hauke/openwrt/openwrt/staging_dir/target-mips_mips32_musl/usr/lib/libubox.so: unknown type [0x7000002a] section `.MIPS.abiflags'
mips-openwrt-linux-musl/bin/ld: /home/hauke/openwrt/openwrt/staging_dir/target-mips_mips32_musl/usr/lib/libubox.so: unknown type [0x7000002a] section `.MIPS.abiflags'
mips-openwrt-linux-musl/bin/ld: skipping incompatible /home/hauke/openwrt/openwrt/staging_dir/target-mips_mips32_musl/usr/lib/libubox.so when searching for -lubox
This reverts commit f421fefa8a.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This reverts commit 50a5a8993d as the bump
to 2021.01 unveiled issue with missing swig host tool needed for
mx6cuboxi's SPL.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
When transmitting to a receiver in dynamic SMPS mode, all transmissions that
use multiple spatial streams need to be sent using CTS-to-self or RTS/CTS to
give the receiver's extra chains some time to wake up.
This fixes the tx rate getting stuck at <= MCS7 for some clients, especially
Intel ones, which make aggressive use of SMPS.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
On hardware that supports this, this will improve performance by passing
802.3 frames from the hardware to the stack
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix license information.
Fix wrong ABI version. The library is versioned as libnftnl.so.11.4.0
Add PKG_BUILD_PARALLEL for faster compilation.
Remove autoreconf as nothing is being patched.
Minor cleanups for consistency between packages.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
The first two are useless as /bin/sh can execute those scripts just
fine. Shellcheck reports no problems.
Telnetd patch is useless as telnet is no longer used in OpenWrt.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Remove stime backport.
Remove static libgcc patch as upstream fixed it with
BUSYBOX_DEFAULT_STATIC_LIBGCC which defauls to off.
Remove date -k patch as it no longer applies. It's also pointless as
busybox' hwclock utility can do the same thing.
Remove ntpd patch as that seems to have been applied upstream.
Add smalll patch fixing compilation with SELinux. Upstream commit
2496616b0a8d1c80cd1416b73a4847b59b9f969a renamed the variable without
renaming it in the SELinux path.
Refresh config and patches.
Config refresh:
Refresh commands, run after busybox is first built once:
cd package/utils/busybox/config/
../convert_menuconfig.pl ../../../../build_dir/target-mips_24kc_musl/busybox-default/busybox-1.33.0
cd ..
./convert_defaults.pl < ../../../build_dir/target-mips_24kc_musl/busybox-default/busybox-1.33.0/.config > Config-defaults.in
Manual edits needed afterward:
* Config-defaults.in: OpenWrt config symbol IPV6 logic applied to
BUSYBOX_DEFAULT_FEATURE_IPV6
* Config-defaults.in: OpenWrt configTARGET_bcm53xx logic applied to
BUSYBOX_DEFAULT_TRUNCATE (commit 547f1ec)
* editors/Config.in: Add USE_GLIBC dependency to
BUSYBOX_CONFIG_FEATURE_VI_REGEX_SEARCH (commit f141090)
* shell/Config.in : change at "Options common to all shells" the symbol
SHELL_ASH --> BUSYBOX_CONFIG_SHELL_ASH
(discussion in http://lists.openwrt.org/pipermail/openwrt-devel/2021-January/033140.html
Apparently our script does not see the hidden option while
prepending config options with "BUSYBOX_CONFIG_" which leads to a
missed dependency when the options are later evaluated.)
* Edit Config.in files by adding quotes to sourced items in
config/Config.in, networking/Config.in and util-linux/Config.in (commit 1da014f)
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
[Added comments from Hannu Nyman to commit message]
Signed-off-by: Rosen Penev <rosenp@gmail.com>
The date -k patch is non standard and will be removed in the next
commit.
Tested behavior to be identical with a simple C program:
#define _GNU_SOURCE
#include <unistd.h>
#include <stdio.h>
#include <sys/time.h>
#include <sys/syscall.h>
int main()
{
struct timezone tt;
struct timezone tz;
int a = syscall(SYS_gettimeofday, NULL, &tt);
int b = gettimeofday(NULL, &tz);
printf("%d - %d, %d\n", a, tt.tz_minuteswest, tt.tz_dsttime);
printf("%d - %d, %d\n", b, tz.tz_minuteswest, tz.tz_dsttime);
}
Signed-off-by: Rosen Penev <rosenp@gmail.com>
The removed patches were applied upstream.
This adapts ath10k-ct and mt76 to changed APIs.
nl80211.h in iw is updated to match the version from backports.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The removed patches were applied upstream.
Remove the 300-mac80211-optimize-skb-resizing.patch.
This patch was not applied upstream, but it conflicts with upstream
changes and needs bigger changes. It was applied with Felix to remove
this patch for now. It should be reworked and then send upstream later.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Refreshed all patches, removed 110-mx6cuboxi-mmc-fallback.patch as it
seems, that upstream has probably added similar funcionality in commit
6c3fbf3e456c ("mx6cuboxi: customize board_boot_order to access eMMC")
and it needs to be re-verified by device owner.
Run tested on apalis.
Cc: Felix Fietkau <nbd@nbd.name>
Cc: Vladimir Vid <vladimir.vid@sartura.hr>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
5a2dd18 iwinfo: add hardware description for MediaTek MT7622
4a32b33 iwinfo: add PCI ID for MediaTek MT7613BE
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This patch is required to be able to roam from one backhaul AP to
another one in the same ESS.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(daniel@makrotopia.org: PKG_REVISION bump and refreshed patches)
Signed-off-by: Raphaël Mélotte <raphael.melotte@mind.be>
This patch allows other applications to get events management
frames (for example: association requests).
This is useful in Multi-AP context to be able to save association
requests from stations.
It has been sent to upstream hostapd in this series:
https://patchwork.ozlabs.org/project/hostap/list/?series=217500
'700-wifi-reload.patch' is updated due to the introduction of
'110-notify-mgmt-frames.patch'.
Signed-off-by: Raphaël Mélotte <raphael.melotte@mind.be>
After looking at various vendor GPL source code dumps I discovered that some
of them contain updated versions of ltq-ptm driver when compared to what
openwrt has.
The driver update is mostly cursory (simple changes to comments, whitespace,
formatting etc.) or adds debug features not used by openwrt.
However the updated driver also contains a later version of PTM firmware which
is extracted and included in this commit along with bits to correctly identify
its version when driver loads.
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
The 'bromimage' tool which is used to wrap bl2 with a MediaTek-specific
header is distributed in binary form only and unfortunately tries to
dynamically link against libopenssl, which fails on the buildbots.
Wait for MTK to provide a at least static executable instead, in the
meantime, mark the package as broken.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
HOST_CFLAGS were ignored as they were passed on incorrectly which lead
to build failure if OpenSSL wasn't present on the build host.
Fix that by properly passing HOST_CFLAGS when building each tool.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This should fix CVE-2021-3336:
DoTls13CertificateVerify in tls13.c in wolfSSL through 4.6.0 does not
cease processing for certain anomalous peer behavior (sending an
ED22519, ED448, ECC, or RSA signature without the corresponding
certificate).
The patch is backported from the upstream wolfssl development branch.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
luci now uses ubus directly, so remove 'lucistat'.
For manual usage just print the ubus output, use luci for a pretty
version.
Signed-off-by: Andre Heider <a.heider@gmail.com>
luci now uses ubus directly, so remove 'lucistat'.
For manual usage just print the ubus output, use luci for a pretty
version.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Tested-by: Martin Schiller <ms@dev.tdt.de>
procd sends sigterm to stop daemons, hook it up.
This speeds up the shutdown sequence and gets rid of the following message:
daemon.info procd: Instance dsl_control::instance1 pid 15408 not stopped on SIGTERM, sending SIGKILL instead
Signed-off-by: Andre Heider <a.heider@gmail.com>
Tested-by: Martin Schiller <ms@dev.tdt.de>
dnsmasq v2.84rc2 has been promoted to release.
No functional difference between v2.83test3 and v2.84/v2.84rc2
Backport 2 patches to fix the version reporting
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Use new ubus-based hotplug call in dhcp-script.sh
As sysntpd now makes use of the new ubus-based hotplug calls, dnsmasq
no longer needs to ship ACL to cover ntpd-hotplug.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
erley.org no longer exists; attempting to connect to it during package
download results in lengthy timeouts. Use the new OpenWrt CDN alias to
download from reliable OpenWrt mirrors.
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Multiple sources are hosted on OpenWrts source server only. The source
URLs to point to the server vary based on different epochs in OpenWrts
history.
Replace all by @OPENWRT which is an "empty" mirror, therefore using the
fallback servers sources.cdn.openwrt.org and sources.openwrt.org.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Commit 7c8c4f1be6 ("hostapd: fix P2P group information processing
vulnerability") was missing the actual patch for the vulnerability.
Fixes: 7c8c4f1be6 ("hostapd: fix P2P group information processing vulnerability")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Package ARM Trusted Firmware host tools separately.
(instead of building tfa-fiptool as part of tfa-layerscape)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
ATF bl2 comes in 4 variants for MT7622 depending on the boot media:
* nor
* snand
* emmc
* sdmmc
Additional binary headers needed for emmc and sdmmc are downloaded as
well and provided along with bl2*.bin and bl31.bin to allow building
images including ATF for MT7622.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
If the driver uses .sta_add, station entries are only uploaded after the sta
is in assoc state. Fix early station rate table updates by deferring them
until the sta has been uploaded
Signed-off-by: Felix Fietkau <nbd@nbd.name>
With upstream commit f81f9f0ebac5 ("rockchip: rockpro64: initialize USB in
preboot") CONFIG_USE_PREBOOT was enabled on the RockPro64, which is causing
boot issues when a eMMC is used, as a workaround will temporarily disable
this option.
Signed-off-by: Marty Jones <mj8263788@gmail.com>
[Improve patch description]
Signed-off-by: David Bauer <mail@david-bauer.net>
Enable support for the Ubiquiti UniFi Outdoor+ RF filter via
device-tree. The old way of using platform data is not required anymore,
as it was only used on the now removed ar71xx target.
Signed-off-by: David Bauer <mail@david-bauer.net>
Replace with sed as done elsewhere.
Fixes error with at least btrfs-progs:
Package '@LIBSELINUX@', required by 'mount', not found
Package '@LIBCRYPTSETUP@', required by 'mount', not foun
Signed-off-by: Rosen Penev <rosenp@gmail.com>
The two required tools fail to identify their version when not compiling
from a git clone, patch that in and pass on the used commit hashes.
Upon boot it now prints "WTMI-devel-18.12.1-5598e150".
Signed-off-by: Andre Heider <a.heider@gmail.com>
The cpufreq issue has been identified and a fix is in the process of beeing
upstreamed [0].
Bump the boards to the default 1000MHz so they can run at that frequency
once the fix is merged. Until then the boards are stuck at 800MHz (just
claiming to run 1000Hz, which is a lie).
[0] https://lore.kernel.org/linux-arm-kernel/20210114124032.12765-1-pali@kernel.org/
Signed-off-by: Andre Heider <a.heider@gmail.com>
v5.10 has been released for strace. As such, let's go ahead bring in the
latest version of this package.
See here for the changelog:
https://github.com/strace/strace/releases/tag/v5.10
Signed-off-by: Geordan Neukum <gneukum1@gmail.com>
Pstore (persistent store) can be used to stash debug information (kernel
console, panics, ftrace) across reboots or crashes. If the filesystem is
present, mount it.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Changelog:
- ath10k-ct: Pull in some upstream patches.
Runtime-tested on ipq806x (Netgear R7800).
Signed-off-by: Michael Yartys <michael.yartys@gmail.com>
/lib/functions.sh was executable for no obvious reason and its
execute property was even checked in package-ipkg.mk just to
source it afterwards.
Remove the execute bit and shebang as this is clearly a library.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reviewed-by: Philip Prindeville <philipp@redfish-solutions.com>
This drops the shebang from another bunch of files in various /lib
folders, as these are sourced and the shebang is useless.
Fix execute bit in one case, too.
This should cover almost all trivial cases now, i.e. where /lib is
actually used for library files.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
65abbcd9f6fb mt76: usb: process URBs with status EPROTO properly
3199ef5fa35e mt76: mt7615: set mcu country code in mt7615_mcu_set_channel_domain()
5c86d5bb079b mt76: mt7915: Remove unneeded semicolon
3f546330b59d mt76: mt7915: support TxBF for DBDC
032ad7e02545 mt76: mt7615: unify init work
cc3f23d1e654 mt76: mt7915: bring up the WA event rx queue for band1
fa3d334a0e22 mt76: fix crash on tearing down ext phy
c4c9c402d14a mt76: mt7915: fix vif sta index for DBDC
eca2f0ec0d4c mt76: mt7915: fix command id for txbf action
c828124ef9a5 mt76: mt7915: add support for using a secondary PCIe link for gen1
dbaf0f4679f3 mt76: mt7915: make vif index per adapter instead of per band
fb3e5ce1eb00 mt76: move vif_mask back from mt76_phy to mt76_dev
be2bea66d6e3 mt76: mt7915: detect wrong nss eeprom parameter on dbdc cards
8dc5d4a0da7c Revert "mt76: mt7915: fix vif sta index for DBDC"
8c796a33781c mt76: mt7915: only set int1 when using the second hif
4eb5caaf6cc1 mt76: reduce q->lock hold time
0714890bf0fd mt76: mt7615: reduce VHT maximum MPDU length
2f85aa5cbc62 mt76: mt7915: avoid writes to MT_PCIE_RECOG_ID when not using gen1 devices
8696919d9aae mt76: dma: fix a possible memory leak in mt76_add_fragment()
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This commit is only added to keep the PKG_RELEASE correct after fixing
the $(COMMITCOUNT) logic in the previous commit.
This way the PKG_RELEASE stays the same while the compiled packages
content isn't changed.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Certificate signature algorithm was being set after call to
`wc_MakeCert`, resulting in a mismatch between specified signature in
certificate and the actual signature type.
Signed-off-by: Jeffrey Elms <jeff@wolfssl.com>
[fix commit subject, use COMMITCOUNT]
Signed-off-by: Paul Spooren <mail@aparcar.org>
Use the latest stable kernel since the previous 5.8.x series is EOL.
Also drop the following patches recently accepted upstream:
* 001-libbpf-ensure-no-local-symbols-counted-in-ABI-check.patch
* 002-libbpf-fix-build-failure-from-uninitialized-variable.patch
* 003-bpftool-allow-passing-BPFTOOL_VERSION-to-make.patch
* 004-v5.9-bpftool-use-only-ftw-for-file-tree-parsing.patch
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
dnsmasq v2.83 has a bug in handling duplicate queries which means it may
try to reply using the incorrect network socket. This is especially
noticeable in dual stack environments where replies may be mis-directed to
IPv4 addresses on an IPv6 socket or IPv6 addresses on an IPv4 socket.
This results in system log spam such as:
dnsmasq[16020]: failed to send packet: Network unreachable
dnsmasq[16020]: failed to send packet: Address family not supported by protocol
dnsmasq v2.84test3 resolves these issues.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
FCC ID: A8J-EAP1200H
Engenius EAP1200H is an indoor wireless access point with
1 Gb ethernet port, dual-band wireless,
internal antenna plates, and 802.3at PoE+
**Specification:**
- QCA9557 SOC
- QCA9882 WLAN PCI card, 5 GHz, 2x2, 26dBm
- AR8035-A PHY RGMII GbE with PoE+ IN
- 40 MHz clock
- 16 MB FLASH MX25L12845EMI-10G
- 2x 64 MB RAM NT5TU32M16FG
- UART at J10 populated
- 4 internal antenna plates (5 dbi, omni-directional)
- 5 LEDs, 1 button (power, eth0, 2G, 5G, WPS) (reset)
**MAC addresses:**
MAC addresses are labeled as ETH, 2.4G, and 5GHz
Only one Vendor MAC address in flash
eth0 ETH *:a2 art 0x0
phy1 2.4G *:a3 ---
phy0 5GHz *:a4 ---
**Serial Access:**
the RX line on the board for UART is shorted to ground by resistor R176
therefore it must be removed to use the console
but it is not necessary to remove to view boot log
optionally, R175 can be replaced with a solder bridge short
the resistors R175 and R176 are next to the UART RX pin at J10
**Installation:**
2 ways to flash factory.bin from OEM:
Method 1: Firmware upgrade page:
OEM webpage at 192.168.1.1
username and password "admin"
Navigate to "Firmware Upgrade" page from left pane
Click Browse and select the factory.bin image
Upload and verify checksum
Click Continue to confirm and wait 3 minutes
Method 2: Serial to load Failsafe webpage:
After connecting to serial console and rebooting...
Interrupt uboot with any key pressed rapidly
execute `run failsafe_boot` OR `bootm 0x9fd70000`
wait a minute
connect to ethernet and navigate to
"192.168.1.1/index.htm"
Select the factory.bin image and upload
wait about 3 minutes
**Return to OEM:**
If you have a serial cable, see Serial Failsafe instructions
otherwise, uboot-env can be used to make uboot load the failsafe image
*DISCLAIMER*
The Failsafe image is unique to Engenius boards.
If the failsafe image is missing or damaged this will brick the device
DO NOT downgrade to ar71xx this way, it can cause kernel loop or halt
ssh into openwrt and run
`fw_setenv rootfs_checksum 0`
reboot, wait 3 minutes
connect to ethernet and navigate to 192.168.1.1/index.htm
select OEM firmware image from Engenius and click upgrade
**TFTP recovery:**
Requires serial console, reset button does nothing
rename initramfs to 'vmlinux-art-ramdisk'
make available on TFTP server at 192.168.1.101
power board, interrupt boot
execute tftpboot and bootm 0x81000000
NOTE: TFTP is not reliable due to bugged bootloader
set MTU to 600 and try many times
**Format of OEM firmware image:**
The OEM software of EAP1200H is a heavily modified version
of Openwrt Kamikaze. One of the many modifications
is to the sysupgrade program. Image verification is performed
simply by the successful ungzip and untar of the supplied file
and name check and header verification of the resulting contents.
To form a factory.bin that is accepted by OEM Openwrt build,
the kernel and rootfs must have specific names...
openwrt-ar71xx-generic-eap1200h-uImage-lzma.bin
openwrt-ar71xx-generic-eap1200h-root.squashfs
and begin with the respective headers (uImage, squashfs).
Then the files must be tarballed and gzipped.
The resulting binary is actually a tar.gz file in disguise.
This can be verified by using binwalk on the OEM firmware images,
ungzipping then untaring.
Newer EnGenius software requires more checks but their script
includes a way to skip them, otherwise the tar must include
a text file with the version and md5sums in a deprecated format.
The OEM upgrade script is at /etc/fwupgrade.sh.
OKLI kernel loader is required because the OEM software
expects the kernel to be no greater than 1536k
and the factory.bin upgrade procedure would otherwise
overwrite part of the kernel when writing rootfs.
Note on PLL-data cells:
The default PLL register values will not work
because of the external AR8035 switch between
the SOC and the ethernet port.
For QCA955x series, the PLL registers for eth0 and eth1
can be see in the DTSI as 0x28 and 0x48 respectively.
Therefore the PLL registers can be read from uboot
for each link speed after attempting tftpboot
or another network action using that link speed
with `md 0x18050028 1` and `md 0x18050048 1`.
The clock delay required for RGMII can be applied
at the PHY side, using the at803x driver `phy-mode`.
Therefore the PLL registers for GMAC0
do not need the bits for delay on the MAC side.
This is possible due to fixes in at803x driver
since Linux 5.1 and 5.3
Signed-off-by: Michael Pratt <mcpratt@pm.me>
This is a helpful utility, but it does not have any dependencies
in this repository. Move it to packages feed.
The package does not seem to have a maintainer.
Cc: Jo-Philipp Wich <jo@mein.io>
Cc: Nick Hainke <vincent@systemli.org>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This is a helpful utility, but it does not have any dependencies
in this repository. Move it to packages feed.
Cc: Jo-Philipp Wich <jo@mein.io>
Cc: Nick Hainke <vincent@systemli.org>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The newly added `$(COMMITCOUNT)` varialbe allows automatic versioning
based on the number of Git commits of a package. Replace *tedious to
bump* and *merge conflict causing* `PKG_RELEASE` and replace it with
`$(COMMITCOUNT)`.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Xiaomi Mi Router 4 is the same as Xiaomi Mi Router 3G, except for
the RAM (256Mib→128Mib), LEDs and gpio (MiNet button).
Specifications:
Power: 12 VDC, 1 A
Connector type: barrel
CPU1: MediaTek MT7621A (880 MHz, 4 cores)
FLA1: 128 MiB (ESMT F59L1G81MA)
RAM1: 128 MiB (ESMT M15T1G1664A)
WI1 chip1: MediaTek MT7603EN
WI1 802dot11 protocols: bgn
WI1 MIMO config: 2x2:2
WI1 antenna connector: U.FL
WI2 chip1: MediaTek MT7612EN
WI2 802dot11 protocols: an+ac
WI2 MIMO config: 2x2:2
WI2 antenna connector: U.FL
ETH chip1: MediaTek MT7621A
Switch: MediaTek MT7621A
UART Serial
[o] TX
[o] GND
[o] RX
[ ] VCC - Do not connect it
MAC addresses as verified by OEM firmware:
use address source
LAN *:c2 factory 0xe000 (label)
WAN *:c3 factory 0xe006
2g *:c4 factory 0x0000
5g *:c5 factory 0x8000
Flashing instructions:
1.Create a simple http server (nginx etc)
2.set uart enable
To enable writing to the console, you must reset to factory settings
Then you see uboot boot, press the keyboard 4 button (enter uboot command line)
If it is not successful, repeat the above operation of restoring the factory settings.
After entering the uboot command line, type:
setenv uart_en 1
saveenv
boot
3.use shell in uart
cd /tmp
wget http://"your_computer_ip:80"/openwrt-ramips-mt7621-xiaomi_mir4-squashfs-kernel1.bin
wget http://"your_computer_ip:80"/openwrt-ramips-mt7621-xiaomi_mir4-squashfs-rootfs0.bin
mtd write openwrt-ramips-mt7621-xiaomi_mir4-squashfs-kernel1.bin kernel1
mtd write openwrt-ramips-mt7621-xiaomi_mir4-squashfs-rootfs0.bin rootfs0
nvram set flag_try_sys1_failed=1
nvram commit
reboot
4.login to the router http://192.168.1.1/
Installation via Software exploit
Find the instructions in the https://github.com/acecilia/OpenWRTInvasion
Signed-off-by: Dmytro Oz <sequentiality@gmail.com>
[commit message facelift, rebase onto shared DTSI/common device
definition, bump uboot-envtools]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Device specifications:
======================
* Qualcomm/Atheros QCA9558 ver 1 rev 0
* 720/600/240 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 3T3R 2.4 GHz Wi-Fi (11n)
* 3T3R 5 GHz Wi-Fi (11ac)
* 6x GPIO-LEDs (2x wifi, 2x status, 1x lan, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default))
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 1x ethernet
- AR8035 ethernet PHY (RGMII)
- 10/100/1000 Mbps Ethernet
- 802.3af POE
- used as LAN interface
* 12-24V 1A DC
* internal antennas
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to the
device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann <sven@narfation.org>
[rebase, add LED migration]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Device specifications:
======================
* Qualcomm/Atheros QCA9558 ver 1 rev 0
* 720/600/240 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 3T3R 2.4 GHz Wi-Fi (11n)
* 3T3R 5 GHz Wi-Fi (11ac)
* 6x GPIO-LEDs (2x wifi, 2x status, 1x lan, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default))
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 1x ethernet
- AR8035 ethernet PHY (RGMII)
- 10/100/1000 Mbps Ethernet
- 802.3af POE
- used as LAN interface
* 12-24V 1A DC
* internal antennas
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to the
device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann <sven@narfation.org>
[rebase, apply shared DTSI/device node, add LED migration]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Device specifications:
======================
* Qualcomm/Atheros QCA9558 ver 1 rev 0
* 720/600/240 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 3T3R 2.4 GHz Wi-Fi
* 3T3R 5 GHz Wi-Fi
* 6x GPIO-LEDs (2x wifi, 2x status, 1x lan, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default))
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 1x ethernet
- AR8035 ethernet PHY (RGMII)
- 10/100/1000 Mbps Ethernet
- 802.3af POE
- used as LAN interface
* 12-24V 1A DC
* internal antennas
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to the
device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann <sven@narfation.org>
[rebase, add LED migration]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Device specifications:
======================
* Qualcomm/Atheros QCA9558 ver 1 rev 0
* 720/600/240 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 3T3R 2.4 GHz Wi-Fi
* 3T3R 5 GHz Wi-Fi
* 6x GPIO-LEDs (2x wifi, 2x status, 1x lan, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default))
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 1x ethernet
- AR8035 ethernet PHY (RGMII)
- 10/100/1000 Mbps Ethernet
- 802.3af POE
- used as LAN interface
* 12-24V 1A DC
* internal antennas
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to the
device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann <sven@narfation.org>
[rebase, add LED migration]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Device specifications:
======================
* Qualcomm/Atheros AR9344 rev 2
* 560/450/225 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2T2R 2.4 GHz Wi-Fi
* 2T2R 5 GHz Wi-Fi
* 8x GPIO-LEDs (6x wifi, 1x wps, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default))
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 1x ethernet
- AR8035 ethernet PHY (RGMII)
- 10/100/1000 Mbps Ethernet
- 802.3af POE
- used as LAN interface
* 12-24V 1A DC
* internal antennas
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to the
device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann <sven@narfation.org>
[rebase, add LED migration]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Device specifications:
======================
* Qualcomm/Atheros AR9344 rev 2
* 560/450/225 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2T2R 2.4 GHz Wi-Fi
* 2T2R 5 GHz Wi-Fi
* 4x GPIO-LEDs (2x wifi, 1x wps, 1x power)
* 1x GPIO-button (reset)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 1x ethernet
- AR8035 ethernet PHY (RGMII)
- 10/100/1000 Mbps Ethernet
- 802.3af POE
- used as LAN interface
* 12-24V 1A DC
* internal antennas
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to the
device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann <sven@narfation.org>
[rebase, make WLAN LEDs consistent, add LED migration]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The "cidr_contains6" functions clones the given cidr. The contains4
does not clone the cidr. Both functions do not behave the same.
I see no reason to push the cidr. I think that we get only a negligible
performance gain, but it makes ipv4 and ipv6 equal again.
Signed-off-by: Nick Hainke <vincent@systemli.org>
This fixes the following security problems in dnsmasq:
* CVE-2020-25681:
Dnsmasq versions before 2.83 is susceptible to a heap-based buffer
overflow in sort_rrset() when DNSSEC is used. This can allow a remote
attacker to write arbitrary data into target device's memory that can
lead to memory corruption and other unexpected behaviors on the target
device.
* CVE-2020-25682:
Dnsmasq versions before 2.83 is susceptible to buffer overflow in
extract_name() function due to missing length check, when DNSSEC is
enabled. This can allow a remote attacker to cause memory corruption
on the target device.
* CVE-2020-25683:
Dnsmasq version before 2.83 is susceptible to a heap-based buffer
overflow when DNSSEC is enabled. A remote attacker, who can create
valid DNS replies, could use this flaw to cause an overflow in a heap-
allocated memory. This flaw is caused by the lack of length checks in
rtc1035.c:extract_name(), which could be abused to make the code
execute memcpy() with a negative size in get_rdata() and cause a crash
in Dnsmasq, resulting in a Denial of Service.
* CVE-2020-25684:
A lack of proper address/port check implemented in Dnsmasq version <
2.83 reply_query function makes forging replies easier to an off-path
attacker.
* CVE-2020-25685:
A lack of query resource name (RRNAME) checks implemented in Dnsmasq's
versions before 2.83 reply_query function allows remote attackers to
spoof DNS traffic that can lead to DNS cache poisoning.
* CVE-2020-25686:
Multiple DNS query requests for the same resource name (RRNAME) by
Dnsmasq versions before 2.83 allows for remote attackers to spoof DNS
traffic, using a birthday attack (RFC 5452), that can lead to DNS
cache poisoning.
* CVE-2020-25687:
Dnsmasq versions before 2.83 is vulnerable to a heap-based buffer
overflow with large memcpy in sort_rrset() when DNSSEC is enabled. A
remote attacker, who can create valid DNS replies, could use this flaw
to cause an overflow in a heap-allocated memory. This flaw is caused
by the lack of length checks in rtc1035.c:extract_name(), which could
be abused to make the code execute memcpy() with a negative size in
sort_rrset() and cause a crash in dnsmasq, resulting in a Denial of
Service.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The referenced commit is gone, but we already have this file on our
mirror, use that one by providing the correct mirror hash.
I generated a tar.xz file with the given git commit hash using a random
fork on github and it generated the same tar.xz file as found on our
mirror so this looks correct.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The referenced commit is gone, but we already have this file on our
mirror, use that one by providing the correct mirror hash.
I generated a tar.xz file with the given git commit hash using a random
fork on github and it generated the same tar.xz file as found on our
mirror so this looks correct.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
53f07e9 ra: fix routing loop on point to point links
2b6959d ra: align ifindex resolving
Tested-by: Karl Vogel <karl.vogel@gmail.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
