Backport 2 patches for Armada 3720 comphy from 5.15 kernel.
These are needed for clear application of pending patches that fix this
driver.
Signed-off-by: Marek Behún <kabel@kernel.org>
Backport Aardvark PCIe controller driver changes that fix MSI support,
that were recently sent to the linux-pci mailing list [1].
These changes fix MSI and MSI-X support for this PCIe controller, which,
among other things, make it possible to use NVMe drives with this PCIe
controllers.
[1] https://lore.kernel.org/linux-pci/20220110015018.26359-1-kabel@kernel.org/
Signed-off-by: Marek Behún <kabel@kernel.org>
This does not have spare blocks for remapping, and it is also not suitable
for random write access. It only skips over bad blocks on linear writes of an
image to a partition. As such, it is really only suitable for the kernel
partition, or other partitions with mostly static data
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This can be used to support ubi on top of mtk_bmt without reflashing the
boot loader. The boot loader + factory + kernel area is covered, while the
rest is passed through as-is
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add support for showing remapped blocks and garbage collecting old
remapped blocks triggered by using the mark_good/mark_bad files
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Preparation for supporting BMT on MT7621. Move source files to the files/
subdirectory in order to simplify maintenance
Signed-off-by: Felix Fietkau <nbd@nbd.name>
If the SPI probe is sufficiently delayed, the routerboot driver may fail
to init as the routerboot partitions are not yet available.
Register an MTD user notifier instead of doing straight init so that the
init subroutines are only executed when the target MTD partitions are
present.
Because the init/exit routines can now be called outside of the kernel
normal init/exit calls, they cannot be jettisoned and must always be
available: the __init and __exit qualifiers are thus removed.
Reported-by: Denis Kalashnikov <denis281089@gmail.com>
Signed-off-by: Denis Kalashnikov <denis281089@gmail.com>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Reviewed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
[bump hardconfig/softconfig versions]
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Make soft_config writable in all cases. Performing soft_config commit
will fail if mtd partition is not writable.
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
[bump rb_softconfig version number]
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Set policy bit to force read-only mode on uImage.FIT filesystem
sub-images mapped as block partitions by the FIT partition parser.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add and enable a new kconfig knob to disable unprivileged eBPF by default.
Patches automatically rebased.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* correctly set system side interface, the original patch was
errornous and there is a follow-up fix for it
* enable phy statistics for AQR112(+R/C) and ARQ412
(ethtool --phy-statistics ethX)
Tested, including phy-statistics, on
- IEI Puzzle M901 (AQR112, AQR112C, AQR112R)
- IEI Puzzle M902 (AQR113, AQR112R)
- Ubiquiti UniFi 6 LR (AQR112C)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Backport qca8k new feature:
- Ageing configuration support
- Add 2 missing counter on qca8337
- Convert to regmap
- Standardize define and code with GENMASK AND BITFILED macro
- Add mdb add/del support
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Backport 3 additional fixes for qca8k.
- Fix MTU calculation
- Fix a bug with config set to the wrong PAD when secondary cpu port is defined.
- Fix redundant check in parse_port_config
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
All patches automatically rebased.
Build system: x86_64
Build-tested: ramips/mt7621*
*Had to revert 7f1edbd in order to build due to FS#4149
Signed-off-by: John Audia <graysky@archlinux.us>
mtd: spi-nor: locking support for MX25L6405D
Macronix MX25L6405D supports locking with four block-protection bits.
Currently, the driver only sets three bits. If the bootloader does not
sustain the flash chip in an unlocked state, the flash might be
non-writeable. Add the corresponding flag to enable locking support with
four bits in the status register.
mtd: spi-nor: disable 16-bit-sr for macronix
Macronix flash chips seem to consist of only one status register.
These chips will not work with the "16-bit Write Status (01h) Command".
Disable SNOR_F_HAS_16BIT_SR for all Macronix chips.
Refreshed:
- 0052-mtd-spi-nor-use-4-bit-locking-for-MX25L12805D.patch
Fixes: 15aa53d7ee ("ath79: switch to Kernel 5.10")
Signed-off-by: Nick Hainke <vincent@systemli.org>
Linkstation poweroff driver was added to mvebu target, but is required
for kirkwood target too.
This commit make two changes:
- move linkstation-poweroff support patch from mvebu to generic and
replace upstream accepted version
- backport small linkstation-poweroff fix from 5.12
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
ath25 requires a 88E6060 driver to support boards such as Fonera 2.0g
(FON2202). The swconfig based mvswitch driver has not yet been ported to
the 5.10 kernel as the only user is the ath25 target while all other
targets have been switched to the upstream DSA implementation.
Switching ath25 to the DSA implementation is a complex task, since we
need either per-board platform data or DTS support. ath25 lacks both of
them and builds only a single generic image. So we need to keep the
swconfig driver implementation to easly and quickly port ath25 to the
5.10 kernel.
Since porting the mvswitch driver to 5.10 as a generic driver is not an
option, and since the ath25 is its only user, make mvswitch a target
specific driver to be able to port it to the 5.10 kernel as part of the
kernel version update of the target. This will allow us quickly migrate
to the next kernel version and not delay the next firmware release.
Suggested-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Assuming cmdlinepart is only one level deep partition scheme and that
static partition are also defined in DTS, we can assign an of_node for
partition declared from bootargs.
The cmdlinepart parser is the first parser checked and if it does find
some partition declared in the bootargs, every other parser is ignored.
This means that the fixed-partition parser is ignored and an of_node for
the mtd is never assigned.
Fix this by searching a defined of_node using a similar fixed_partition
parsing logig, check if a partition is present with the same label, check
that it has the same offset and size and finally assign an of_node to the
mtd. The NVMEM can now find the of_node for the mtd and correctly works.
Fixes: abc17bf306 ("ath79: convert mtd-mac-address to nvmem implementation")
Tested-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Copy and refresh patch enabling AQR112 and AQR412 Ethernet PHY from
layerscape (5.4) target to generic (5.10) as AQR112 can also be found
on other targets as well.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Each of
- CRYPTO_AEAD2
- CRYPTO_AEAD
- CRYPTO_GF128MUL
- CRYPTO_GHASH
- CRYPTO_HASH2
- CRYPTO_HASH
- CRYPTO_MANAGER2
- CRYPTO_MANAGER
- CRYPTO_NULL2
either directly required for mac80211 crypto support, or directly
selected by such options. Support for the mac80211 crypto was enabled in
the generic config since c7182123b9 ("kernel: make cryptoapi support
needed by mac80211 built-in"). So move the above options from the target
configs to the generic config to make it clear why do we need them.
CC: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Both CLANG_VERSION and LLD_VERISON are autogenerated runtime
configuration options, so add them to the kernel configuration filter
and remove from generic and per-target configs to keep configs clean.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Removed target for patch which does not exist:
bcm27xx/patches-5.10/950-0249-kbuild-Disable-gcc-plugins.patch
All patches automatically rebased.
Build system: x86_64
Build-tested: bcm2711/RPi4B, ipq806x/R7800*
Run-tested: bcm2711/RPi4B, ipq806x/R7800*
* Had to revert 7f1edbd412 in order to build
(binutils 2.37, https://bugs.openwrt.org/index.php?do=details&task_id=4149)
Signed-off-by: John Audia <graysky@archlinux.us>
All patches automatically rebased.
Build system: x86_64
Build-tested: ramips/mt7621*
*FS#4149 affects me so I had to revert 7f1edbd412
in order to downgrade to 2.35.1
Signed-off-by: John Audia <graysky@archlinux.us>
All patches automatically rebased.
Build system: x86_64
Build-tested: ramips/mt7621*
*FS#4149 affects me so I had to revert 7f1edbd412
in order to downgrade to 2.35.1
Signed-off-by: John Audia <graysky@archlinux.us>
The workqueue based implementation has a few corner cases and typically lower
performance than the upstream one
Signed-off-by: Felix Fietkau <nbd@nbd.name>
NET_DSA_MSCC_FELIX:
Marvell 88E6xxx Ethernet switch fabric support (NET_DSA_MV88E6XXX) [N/m/y/?] n
Ocelot / Felix Ethernet switch support (NET_DSA_MSCC_FELIX) [N/m/y/?] (NEW)
Error in reading or end of file.
make[6]: *** [scripts/kconfig/Makefile:71: syncconfig] Error 1
make[5]: *** [Makefile:603: syncconfig] Error 2
IR_IMON_RAW:
SoundGraph iMON Receiver (early raw IR models) (IR_IMON_RAW) [N/m/?] (NEW)
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
[squashed with "kernel: add missing IR_IMON_RAW config symbol"]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Deactivate all the symbols of the B53 DSA driver in the generic kernel
configuration. Multiple targets are now using this drivers and they
only need some of the options.
This fixes the bcm4908 build which didn't deactivate all of the options.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
All patches automatically rebased.
Build system: x86_64
Build-tested: ramips/mt7621*
*I am hit with the binutils 2.37 bug so I had to revert 7f1edbd412
in order to downgrade to 2.35.1
Signed-off-by: John Audia <graysky@archlinux.us>
Manually rebased:
generic-backport/850-v5.13-usb-ehci-add-spurious-flag-to-disable-overcurrent-ch.patch
All other patches automatically rebased.
Signed-off-by: John Audia <graysky@archlinux.us>
The crashlog patch as not ported to kernel 5.4.
Fixes: 4e0c54bc5b ("kernel: add support for kernel 5.4")
Signed-off-by: Jianhui Zhao <zhaojh329@gmail.com>
Fix mac address increment patch. Permit to overflow to the next
byte and correctly calculate the incremented mac.
Reported-by: Chen Minqiang <ptpt52@gmail.com>
Fixes: d284e6ef0f ("treewide: convert mtd-mac-address-increment* to generic implementation")
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Backport of Ansuel Smith's "net: dsa: qca8k: make sure PAD0 MAC06
exchange is disabled", to ensure mac06 is disabled even if enabled by
the bootloader.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Enabling KERNEL_UBSAN exposes several missing symbols. Add new kernel
build options for UBSAN_BOUNDS and UBSAN_TRAP, disable CONFIG_TEST_UBSAN
in the generic kernel configs and enable CONFIG_UBSAN_MISC in generic
5.10 config. The latter symbol was removed in later kernels, as it was
causing some issues, so just disable it in 5.10 instead of adding a
build option for it.
Fixes build failures with KERNEL_UBSAN enabled.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Enabling KERNEL_KASAN exposes several missing symbols. As KASAN_SW_TAGS
is only implemented for arm64 CPUs and requires clang, it doesn't make
sense to make this a build option so just default to KASAN_GENERIC and
disable KASAN_SW_TAGS.
While at it, disable TEST_KASAN_MODULE in the generic 5.10 config.
Fixes build failures with KERNEL_KASAN enabled.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
The qca8k patch series brings the numbering to 799. This patch renames
7xx patches to create space for more backports to be added.
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
[rename 729->719]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Removed upstreamed:
backport-5.4/790-v5.7-net-switchdev-do-not-propagate-bridge-updates-across.patch
All other patches automatically rebased.
Signed-off-by: John Audia <graysky@archlinux.us>
I had quite a hard time to understand what the change to net/core/dev.c
is supposed to do.
Simplify the change by returning NETDEV_TX_OK in case a eth_mangle_tx
callback was set but returned NULL instead of setting the return value
in the else branch.
Signed-off-by: Mathias Kresin <dev@kresin.me>
ar8216 switches have a hardware bug, which renders normal 802.1q support
unusable. Packet mangling is required to fix up the vlan for incoming
packets.
The patch was ommited at the time kernel 5.10 support was added but is
still required for ar8216 switches.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Don't patch the kernel to expose the partition name in sysfs as it is
already exposed via 'uevent'.
All previous users have been converted to use 'uevent', so we can
safely drop the custom patch.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This fixes support for Dongwon T&I DW02-412H which uses F25L16PA(2S) flash.
Signed-off-by: Jihoon Han <rapid_renard@renard.ga>
Reviewed-by: Sungbo Eo <mans0n@gorani.run>
[refresh patches]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Deleted (upstreamed):
bcm27xx/patches-5.10/950-0145-xhci-add-quirk-for-host-controllers-that-don-t-updat.patch [1]
Manually rebased:
bcm27xx/patches-5.10/950-0355-xhci-quirks-add-link-TRB-quirk-for-VL805.patch
bcm53xx/patches-5.10/180-usb-xhci-add-support-for-performing-fake-doorbell.patch
Note: although automatically rebaseable, the last patch has been edited to avoid
conflicting bit definitions.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=linux-5.10.y&id=b6f32897af190d4716412e156ee0abcc16e4f1e5
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Tidy qca8k_setup for loops relating to port handling. No functional
changes.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Add cpu_port_index fix to apply settings to correct CPU port.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Backport Ansuel Smith's various qca8k feature additions:
- mac-power-sel support
- SGMII PLL explicit enable
- tx/rx clock phase to falling edge
- power-on-sel and LED open drain mode
- cpu port 6
- qca8328 support
- sgmii internal delay
- move port config to dedicated struct
- convert to yaml schema
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Backport workaround for QCA8327 PHY resume, which does not properly support
genphy_suspend/resume. Also add DAC amplitude fix for the QCA8327 PHY,
set port to preferred master and add proper names to debug regs.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
This commit add accepted upstream patches that improve & tidy qca83xx support.
1 - Split qca8327 to A & B variants, identifiable by phy_id
2 - Add suspend/resume support to qca8xx phys
3 - Tidy spacing and phy naming.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Add support for qca8327 internal phy needed for correct init of the
switch port. It does use the same qca8337 function and reg just with a
different id.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Backport fixes including:
net: dsa: qca8k: fix missing unlock on error in qca8k_vlan_(add|del)
net: dsa: qca8k: check return value of read functions correctly
net: dsa: qca8k: add missing check return value in qca8k_phylink_mac_config()
net: dsa: qca8k: fix an endian bug in qca8k_get_ethtool_stats()
net: dsa: qca8k: check the correct variable in qca8k_set_mac_eee()
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
This is a backport of Ansuel Smith's "Multiple improvement to qca8k stability"
series. The QCA8337 switch is available on multiple platforms including
ipq806x, ath79 and bcm53xx.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Rosen reported strange dtc warnings that had their origin in
an upstream patch to 5.8-rc1. Upon further digging this
revealed an ongoing thread [0] discussing the topic:
> [...]I don't think we need a bunch of warning fix patches to add
> these everywhere. Also, the need for #address-cells pretty much makes
> no sense on any modern system. It is a relic from days when the bus
> (address) topology and interrupt topology were related.
and later on:
> So really, we only need to be checking for #address-cells in nodes
> with interrupt-map.
This patch backports just the patch which removed the warning message
(this is from the upstream dtc project [1] - but not the kernel).
the patch does not add the checking of the #address-cells in nodes
with interrupt-map.
[0] <https://lore.kernel.org/linux-devicetree/91e3405245c89f134676449cf3822285798d2ed2.1612189652.git.michal.simek@xilinx.com/>
[1] <https://git.kernel.org/pub/scm/utils/dtc/dtc.git/commit/?id=d8d1a9a77863a8c7031ae82a1d461aa78eb72a7b>
Link: <https://github.com/openwrt/openwrt/pull/4685>
Reported-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This allows to specify and control switch LEDs on devices using mt7530
(typically mediatek and ramips targets).
Normally these LED GPIOs are 0, 3, 6, 9, and 12. wan/lan assignment is
per device. GPIO 9 is normally inverted. so GPIO_ACTIVE_HIGH instead of
GPIO_ACTIVE_LOW.
Tested on Linksys E7350.
Refreshed all patches.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Backport upstream SFP support for the Marvell 88E1510/2 PHY-s.
Globalscale MOCHAbin uses this PHY for the hybrid
WAN port that has 1G SFP and 1G RJ45 with PoE PD
connected to it.
This allows the SFP port to be used on it as well as
parsing the SFP module details with ethtool.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Backport upstream support for 100Base-FX, 100Base-LX, 100Base-PX and
100Base-BX10 SFP modules.
This is a prerequisite for the Globalscale MOCHAbin hybrid 1G
SFP/Copper support backporting.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Removed upstreamed:
backport-5.4/070-v5.5-MIPS-BPF-Restore-MIPS32-cBPF-JIT.patch
All other patches automatically rebased.
Signed-off-by: John Audia <graysky@archlinux.us>
Now that we have fully switched to nvmem interface we can drop
the use of mtd-mac-address patches as it's not used anymore and
the new nvmem implementation should be used for any new device.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
This fixes:
ERROR: "switch_generic_set_link" [drivers/net/phy/b53/b53_common.ko] undefined!
At some point all packages for swconfig drivers were dropped and targets
were meant to have them built into kernels. It seems b53 (re-)gained its
kmod-switch-bcm53xx however and b53 needs to be built as module.
Fixes: b2cfed48f6 ("Revert "swconfig: fix Broadcom b53 support"")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Add Vladimir Oltean's "net: dsa: don't set skb->offload_fwd_mark when
not offloading the bridge"
This covers cases where packets received by an upstream switch must be
forwarded back on the same port, which skb->offload_fwd_mark normally
prevents.
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
This reverts commit 8f9cd1af0f.
That commit was meant to add a single EXPORT_SYMBOL_GPL() but it
actually also added few .of_match_table-s. One commit should handle one
thing and should not introduce unrelated changes.
Regarding actual changes:
1. EXPORT_SYMBOL_GPL is not required as we don't build swconfig drivers
as modules.
2. PHY drivers must not have .of_match_table. That is allowed for MDIO
drivers. This could work for some time (although is didn't for me on
bcm53xx) but does not with kernel 5.10. It causes a soft lockup and
upstream developers confirmed it's an unsupported design.
Link: https://lore.kernel.org/netdev/2b1dc053-8c9a-e3e4-b450-eecdfca3fe16@gmail.com/t/#mf80e472f35ee23f7a75cbf5b1e101a17ab3a64a3
Cc: Tobias Schramm <tobleminer@gmail.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Three missing symbols were found during mpc85xx/p2020 compilation.
While at it, CONFIG_FSL_ENETC_MDIO is moved to generic config
for consistency.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
[move CONFIG_FSL_ENETC_MDIO, remove redundant definitions, adjust
commit message/title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
SATA_PMP option is no longer exposed when no SATA host driver is enabled
since upstream linux commit bd322af15ce9 ("ata: make SATA_PMP option
selectable only if any SATA host driver is enabled").
Commit 1bb3f593ee ("kirkwood: update config for kernel 5.10") manually
added CONFIG_SATA_PMP=y to config file, but the config will disappear for
every kernel_oldconfig refresh.
To prevent this, a small hack is added, which selects SATA_HOST
automatically when SATA_PMP is enabled. This patch can be dropped if
SATA_MV is ever re-added into kernel config file.
Tested-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[Move patch to generic/hack-5.10]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This backports the upstream commit:
leds: lp55xx: Initialize enable GPIO direction to output
Without it under kernel 5.10 on Asus MAP-AC2200
the LED driver will fail probing:
[ 1.947521] lp5523x: probe of 0-0032 failed with error -22
After the backported fix:
[ 1.873236] lp5523x 0-0032: lp5523 Programmable led chip found
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Tested-by: Szabolcs Hubai <szab.hu@gmail.com> [ipq4029/gl-b1300]
Tested-by: Nick Hainke <vincent@systemli.org> [ipq4019/fritzbox-7530
ipq4019/fritzbox-4040
ipq4019/sxtsq-5ac]
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [ipq4019/map-ac2200]
This fixes:
Distributed Switch Architecture (NET_DSA) [Y/n/m/?] y
Tag driver for Atheros AR9331 SoC with built-in switch (NET_DSA_TAG_AR9331) [N/m/y/?] n
Tag driver for Broadcom switches using in-frame headers (NET_DSA_TAG_BRCM) [N/m/y/?] n
Tag driver for Broadcom legacy switches using in-frame headers (NET_DSA_TAG_BRCM_LEGACY) [N/m/y/?] (NEW)
Error in reading or end of file.
Fixes: 8fa1b576bb ("linux: update b53 upstream driver")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This patch fixes the forwarding behavior of bridge in bridge
configurations with DSA.
Without it, the configuration of the upper bridge might overwrite
settings of the lower bridge. For example, a vlan-aware bridge
with DSA interfaces in it might be offloaded to the DSA hardware. If the
bridge interface itself gets slave of a different bridge without vlan
filtering, the vlan filtering setting of the lower bridge is overwritten
by the upper bridge, which results in an incorrect hardware
configuration.
This was backported from kernel 5.7.
Ref: https://lore.kernel.org/netdev/20191222192235.GK25745@shell.armlinux.org.uk/
Fixes: FS#3996
Signed-off-by: Fabian Bläse <fabian@blaese.de>
Designated initializers are required when using the randstruct GCC
plugin, otherwise an error like the following is seen:
./include/linux/lzma.h:60:31: error: positional initialization of field in 'struct' declared with 'designated_init' attribute [-Werror=designated-init]
Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
These options are selectable when some of the kernel debug options like
KERNEL_SOFTLOCKUP_DETECTOR are selected.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The default value for CONFIG_RCU_CPU_STALL_TIMEOUT was changed from 60
seconds to 21 seconds in 2012 in the upstream kernel. Some targets
already use 21 seconds.
This patch changes the default value in the generic configuration to 21
seconds and removes the target specific configuration options.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Rui Salvaterra <rsalvaterra@gmail.com>
CONFIG_RCU_{NEED_SEGCBLIST,STALL_COMMON} are set basically everywhere. Move them
to the generic kconfigs. And resort the generic kconfigs while at it.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Based on the existing documentation [1][2], I dare anyone to demonstrate that
we need to fine-tune these RCU parameters. The (performance) breakage potential
for doing so is immense, so let's just please put down this loaded footgun.
Disable CONFIG_RCU_EXPERT and its dependent symbols. Additionally, remove the
CONFIG_RCU_EXPERT symbol from the target kconfigs which contain it.
[1] https://www.kernel.org/doc/Documentation/RCU/Design/Data-Structures/Data-Structures.html
[2] https://lwn.net/Articles/777214/
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
There is a longlasting warn about unused defined try_to_force_load.
Fix this by including this function only when actually used.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
The uImage.FIT partition uses page mapping without properly handling
paging errors. This can lead to Kernel Oops in case of read errors
while trying to parse uImage.FIT partitions.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The current patch produces the following error when CONFIG_DMABUF_HEAPS is
enabled:
drivers/built-in.a: member drivers/dma-buf/heaps in archive is not an object
Fixes: b10d604459 ("kernel: add linux 5.10 support")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
When a target configuration has unser Kconfig symbols, the build will
fail when OpenWrt is compiled with V=s and stdin is connected to a tty.
In case OpenWrt is compiled without either of these preconditions, the
build will uscceed with the symbols in question being unset.
Modify the kernel configuration in a way it fails on unset symbols
regardless of the aformentioned preconditions.
Signed-off-by: David Bauer <mail@david-bauer.net>
Calling free for the OF property can result in a kernel panic, as the
buffer in question might be referenced elsewhere. Also, it is not
removed from the tree.
Always allocate a new property and updating the tree with it fixes both
issues.
Fixes commit 91a52f22a1 ("treewide: backport support for nvmem on non platform devices")
Signed-off-by: David Bauer <mail@david-bauer.net>
The code from ks8851.c was moved to ks8851_common.c, so it was not
backported. This broke the compile of the omap target which uses this
driver.
Fixes commit 91a52f22a1 ("treewide: backport support for nvmem on non platform devices")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add the missing CONFIG_KCSAN (disabled). Found while making kernel_oldconfig on
an x86-64 subtarget.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
kirkwood build broke due to missing include needed for ETH_ALEN.
Add patch (sent upstream as well) to address that.
Refresh patches for 5.4 and 5.10.
Fixes: 91a52f22a1 ("treewide: backport support for nvmem on non platform devices")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add the missing ARM_SCMI_PROTOCOL symbol. Apparently it was exposed
for 5.10.53 with a kernel dependency change.
Missing symbol observed with mediatek/7622 E8450/RT3200 router.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
The virtual cable tester depends on the netlink interface for ethtool.
Thus, enable it in the generic kernel configuration.
Signed-off-by: David Bauer <mail@david-bauer.net>
In the current state, nvmem cells are only detected on platform device.
To quickly fix the problem, we register the affected problematic driver
with the of_platform but that is more an hack than a real solution.
Backport from net-next the required patch so that nvmem can work also
with non-platform devices and rework our current patch.
Drop the mediatek and dsa workaround and rework the ath10k patches.
Rework every driver that use the of_get_mac_address api.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
bcm27xx-bcm2710 builds are stalling when compiled with V=s.
Explitily disable these unset symbols to avoid stalling
builds.
Signed-off-by: David Bauer <mail@david-bauer.net>
Fixes a unused variable warning:
drivers/of/of_net.c: In function 'of_get_mac_address_mtd':
drivers/of/of_net.c:92:19: warning: unused variable 'prop' [-Wunused-variable]
Signed-off-by: David Bauer <mail@david-bauer.net>
The 1st generation MediaTek PCIe host bridge cannot handle Message
Signaled Interrupts (MSIs). The core PCI code is not aware that MSI is
not available. This results in warnings of the form:
WARNING: CPU: 2 PID: 112 at include/linux/msi.h:219
pci_msi_setup_msi_irqs.constprop.8+0x64/0x6c
Modules linked in: ahci(+) libahci libata sd_mod scsi_mod
gpio_button_hotplug
CPU: 2 PID: 112 Comm: kmodloader Not tainted 5.10.52 #0
Hardware name: Mediatek Cortex-A7 (Device Tree)
Import patches that introduce the 'no_msi' attribute to signal missing
MSI support to the core PCI.
Refresh patches:
- 000-spi-fix-fifo.patch
- 330-mtk-bmt-support.patch
- 510-net-mediatek-add-flow-offload-for-mt7623.patch
- 601-PCI-mediatek-Use-regmap-to-get-shared-pcie-cfg-base.patch
- 610-pcie-mediatek-fix-clearing-interrupt-status.patch
- 700-net-ethernet-mtk_eth_soc-add-support-for-coherent-DM.patch
- 710-pci-pcie-mediatek-add-support-for-coherent-DMA.patch
Signed-off-by: Nick Hainke <vincent@systemli.org>
The label-mac logic relies on the mac-address property of a netdev
devices of-node. However, the mac address can also be stored as a
different property or read from e.g. an mtd device.
Create this node when reading a mac-address from OF if it does not
already exist and copy the mac-address used for the device to this
property. This way, the MAC address can be accessed using procfs.
Signed-off-by: David Bauer <mail@david-bauer.net>
This reverts commit b309248730.
This commit could create a property without allocated memory, breaking
subsequent reads over a nodes property. Also, the mac-address-increment
was not applied when reading from nvmem.
Revert this commit for now, which breaks the label-mac-address logic.
Possibly, traversing the device-tree from the netdev side is easier
anyways.
Signed-off-by: David Bauer <mail@david-bauer.net>
Add CONFIG_HAVE_ARM_ARCH_TIMER (disabled). A make kernel_oldconfig on cortexa9
will otherwise prompt for its selection. The 5.4 configuration already contains
the same symbol.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Add the new CONFIG_BATTERY_RT5033 to the generic configuration, as reported by
Paul Blazejowski. Resort the kconfig while at it.
No deleted or manually refreshed patches.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Adds support for GPON SFP modules based on the Realtek RTL8672 and
RTL9601C chips, including but not limited to:
* V-SOL V2801F
* C-Data FD511GX-RM0
* OPTON GP801R
* BAUDCOM BD-1234-SFM
* CPGOS03-0490 v2.0
* Ubiquiti U-Fiber Instant
* EXOT EGS1
Signed-off-by: Vladimir Markovets <abam_a@yahoo.com>
Latest binutils (2.37) exposed a long-standing bug. The kernel linking stage
would break at the SORTTAB step, due to the exception table having been
previously purged from vmlinux, as its section wasn't marked as unconditionally
kept. Fix thusly.
Additionally, the "#define ARM_MMU_DISCARD(x) KEEP(x)" change is bogus. It
would only apply to !CONFIG_MMU devices (which we don't support in OpenWrt), and
it would even break the build if referenced. Drop it.
While at it, rename the patch in order to make it obvious that it's
arm-specific.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
[Add same changes for kernel 5.4 too]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Nvmem require the device node to be registered with the of_platform.
Register the device node so that nvmem can correctly find the dev and
correctly load the mac-addr stored in the nvmem cell declared in the dts.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Traversing the device-tree by referencing a network device to determine
a devices labe-mac does not work with the generic nvmem implementation,
as the userspace expects the MAC-address to be available as a
device-tree property.
The legacy mtd-mac-address implementation did create such a node. Do the
same when using the nvmem implementation to allow reading the MAC
address.
Fixes commit d284e6ef0f ("treewide: convert mtd-mac-address-increment*
to generic implementation")
Signed-off-by: David Bauer <mail@david-bauer.net>
Introduce new partition type 0x2e representing uImage.FIT and trigger
FIT partition parser on partitions having that type.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Rework patch 681-NET-add-mtd-mac-address-support to implement
only the function to read the mac-address from mtd.
Generalize mtd-mac-address-increment function so it can be applied
to any source of of_get_mac_address.
Rename any mtd-mac-address-increment to mac-address-increment.
Rename any mtd-mac-address-increment-byte to mac-address-increment-byte.
This should make simplify the conversion of target to nvmem implementation.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
When compiling with all modules enabled, Kconfig complains about
CONFIG_I2C_DESIGNWARE_SLAVE being unset. Disable this symbol by default.
Fixes commit e9c9b5ec72 ("kernel: package Synopsys Designware PCI to I2C controller")
Signed-off-by: David Bauer <mail@david-bauer.net>
AR8031/AR8033 have different status registers for copper
and fiber operation. However, the extended status register
is the same for both operation modes.
As a result of that, ESTATUS_1000_XFULL is set to 1 even when
operating in copper TP mode.
Remove this mode from the supported link modes, as this driver
currently only supports copper operation.
Signed-off-by: David Bauer <mail@david-bauer.net>
Manually rebased:
bcm27xx/patches-5.4/950-0089-cgroup-Disable-cgroup-memory-by-default.patch
All other patches automatically rebased.
Signed-off-by: John Audia <graysky@archlinux.us>
Without this patch we have to manually bring up the CPU interface in
failsafe mode.
This was backported from kernel 5.12.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Rafał Miłecki <rafal@milecki.pl>
These are the latest patches that just landed upstream for 5.13, will be
backported by Greg into 5.10 (because of stable@), and are now in the
5.4 backport branch of wireguard: https://git.zx2c4.com/wireguard-linux/log/?h=backport-5.4.y
Cc: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Tested-by: Stijn Segers <foss@volatilesystems.org>
The option was added in 5.9 and for some reason, it is causing performance
issues at least on an APU2 board with the igb device.
Switch CONFIG_PCIE_BUS_DEFAULT to fix the performance issues and match the
older kernel's behavior
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This reduces the flash space impact, since built-in code is much smaller
than a bunch of kernel modules on squashfs
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Atheros PHYs using the at803x driver apart from the AR8031/AR8033 fail
to probe with kernel 5.4, due to ret in at803x_probe being
uninitialized.
[ 1.403461] Atheros 8035 ethernet: probe of 4ef600c00.ethernet:01
failed with error -1066114012
Initialize ret in order to successfully prove the PHYs on kernel 5.4.
Kernel 5.10 is not affected, as the ret is always assigned prior to
returning.
Tested on OCEDO Koala.
Reported-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: David Bauer <mail@david-bauer.net>
As patches for the AR8031/AR8033 copper page selection were merged
upstream, we can backport these patches.
This also fixes a PHY capabilities detection issue on the Ubiquiti
ER-X-SFP.
Signed-off-by: David Bauer <mail@david-bauer.net>
ar8xxx_soft_reset is effectively a NOP function. In the PHY state
machine, the availability and result of a soft_reset function
makes no difference for the code flow.
Thus, we can safely remove this method.
Signed-off-by: David Bauer <mail@david-bauer.net>
Modifying PHY capabilities in the probe function broke with upstream
commit 92ed2eb7f4b7 ("net: phy: probe the PHY before determining the
supported features").
AR8316 switches only support 10/100 Mbit/s link modes because of this
change.
Provide a get_features method for the PHY driver, so Gigabit link mode
will be advertised to link partners again.
Signed-off-by: David Bauer <mail@david-bauer.net>
