Remove the ephy-pins from the ethernet device tree node. The ephy-pins
are useed to controll the ePHY LEDs and this board doesn't have these.
Instead one of the ePHY pins is used in GPIO mode to control the WAN
LED.
Use the switch LED trigger to control the WAN LED. Move the power LED
handling to diag.sh to show the boot status via this LED.
Add the missing kernel packages for USB and microSD card reader to the
default package selection.
Fix the maximum image size value. The board has a 32MByte flash chip.
Fixes: FS#1055
Signed-off-by: Edmunt Pienkowsky <roed@onet.eu>
[make the commit message more verbose, remove GPIO pinmux for pins not
used as GPIOs]
Signed-off-by: Mathias Kresin <dev@kresin.me>
01_leds had a workaround for the power led to compensate for the
inverted GPIO state. This patch was missing from my previous commit.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
[add the power led default-state which was omitted in the last commit
by me]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Luci shows switch ports in wrong order on that device.
This patch fixes switch port numbering and matches them to the device
silkscreen.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
Luci shows switch ports in inverted order on that device.
This patch fixes switch port numbering and matches them to the device
silkscreen.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
The WN3000RPv3 is a repeater with a single ethernet port. Setting up the
switch, even to disable it, is unnecessary and possibly confusing.
Configure LAN as eth0 instead.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
The Sanlinking Technologies D240
(http://www.sanlinking.com/en/29-dual-4g-wifi-router.html) is basically the same
device as the ZBT WE826, so adding support for it in LEDE is straight forward.
The differences is that the D240 has two mini-PCIe slots (instead of one), blue
LEDs and supports PoE.
Specification:
* CPU: MT7620A
* 1x 10/100Mbps POE (802.3af/802.3at) Ethernet, 4x 10/100Mbps.
* 16 MB Flash.
* 128 MB RAM.
* 1x USB 2.0 port.
* 2x mini-PCIe slots.
* 2x SIM slots.
* 1x 2.4Ghz WIFI.
* 1x button.
Wifi, USB, switch and both mini-PCIe slots are working. I have not been able to
test the SD card reader.
The device comes pre-installed with an older version of OpenWRT, including Luci.
In order to install LEDE, you need to follow the existing procedure for updating
OpenWRT/LEDE using Luci. I.e., you need to access the UI and update the firmware
using the sysupgrade-image. Remember to select that you do not want to keep
existing settings. The default router address is 192.168.10.1 and
username/password admin/root (at least on my devices).
If you brick the device, the procedure for recovery is the same as for the
WE826. Please see the wiki page for that device for instructions.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
This patch adds support for the Netgear WN3000RPv3
http://www.netgear.com/support/product/wn3000rpv3.aspx
Specifications:
- SoC: MediaTek MT7620A (580MHz, ramips)
- RAM: 32MB DDR
- Storage: 8MB NOR SPI flash
- Wireless: builtin MT7620A, 2x2:2 with u.FL connectors
- Ethernet: 1x100M
- Serial: JP1 header, 57600-8N1
- Stock firmware based on OpenWRT Kamikaze
Like the EX2700, the bootloader expects a secondary image signature,
see https://forum.openwrt.org/viewtopic.php?pid=312577#p312577
This is why the same fakeroot image is used for the WN3000
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
For the miwifi-mini, the offset of ethernet mac should be 0x28
which you can easyily dump from 'Factory' partition.
Signed-off-by: BangLang Huang <banglang.huang@foxmail.com>
The WN3000RPv3 is a repeater with a single ethernet port. Setting up the
switch, even to disable it, is unnecessary and possibly confusing.
Configure LAN as eth0 instead.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
This patch adds support for the Onion Omega2 and Omega2+ (https://onion.io)
Specifications:
- SoC: MediaTek MT7688AN (580MHz, ramips)
- Omega2
- RAM: 64MB DDR
- Storage: 16MB NOR SPI flash onboard
- Omega2+
- RAM: 128MB DDR
- Storage: 32MB NOR SPI flash onboard + microSD slot
- Wireless: Built into MT7688AN (mt76) with onboard 1x chip antenna and u.FL connecter
- Ethernet: 1x100M pins on Omega2 & Omega2+, can use Ethernet Expansion and an Omega Dock to get a physical Ethernet port
- Strongly recommend using the Omega2 & Omega2+ with a Dock (Expansion Dock, Power Dock, Arduino Dock 2, Mini Dock)
- All Docks Provide:
- Micro-USB port to provide power to the Omega
- On the Expansion and Mini Docks, can also access the terminal (UART0) via serial
- USB 2.0 socket connected to Omega
- Just the Expansion Dock, Power Dock, and Arduino Dock 2 provide:
- Omega GPIO breakout
- Allows for connection of Omega Expansions:
- Ethernet Expansion
- Relay Expansion
- PWM Expansion
- OLED Expansion
- Ethernet Expansion
- Proto Expansion
- Cellular Expansion
Signed-off-by: Lazar Demin <lazar@onion.io>
This patch adds support for the VoCore VoCore2 and its complementary
"ultimate" dock.
Specifications:
- SoC: MediaTek MT7628AN (580MHz, ramips)
- RAM: 128MB DDR2 166MHz
- Storage: 16MB NOR SPI flash onboard + microSD slot on dock
- Wireless: Built into MT7628AN (mt76) with 1T1R firmware on VoCore2
boards with onboard 1x chip antenna
- Ethernet: 1x100M (port0) on dock, 1x100M (port2) on PCB header
- Dock hardware:
- USB 2.0 socket
- MicroSD socket
- 100Mbps Ethernet x1
- 3.5mm headphone jack (TRRS) connected to Everest Semi ES8388 I2S
DAC/ADC (support WIP)
- Micro USB for power and console (UART2)
Initial installation:
- VoCore2 comes preinstalled with a fork of OpenWrt CC and AP on
SSID "VoCore2"
- Connect to VoCore2 by Ethernet or Wi-Fi
- `ssh root@192.168.1.1` (password is "vocore")
- scp/wget/etc. LEDE sysupgrade.bin to VoCore2
- `sysupgrade -n <your image>.bin` (don't keep old config, as the
original firmware uses Ralink SDK Wi-Fi drivers and not
mt76+mac80211)
- after sysupgrade completes, Wi-Fi will be disabled by default so use
Ethernet or the micro USB console to configure Wi-Fi again
Signed-off-by: Andrew Yong <me@ndoo.sg>
Use the the dt-bindings macros and add the reset button.
Set the correct polarity for the LEDs and drop the default state.
Remove all trigger for the LEDs. According to the manual the LEDs are
only used to show the operation state, where blue means normal
operation.
Use the MAC-Addresses stored in EEPROM for the ethernet and the
wireless interface.
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
[use leds only for boot status indication, add proper commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use a distinct board name even if the board is near to identical to
the WeVO W2914NS v2.
To make sure that a 11AC NAS image can not be installed on a
WeVO W2914NS v2, both board need to use different names.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This fixes the partition name for the firmware splitter, the cfi
address and adds the mtd-eeprom address for wmac. It adds additional
LEDs and make use of them in diag.sh and 01_leds.
Please note that the ":blue:wired" LED is used because the
":blue:router" behaviour is unpredictable for failsafe indication. The
issue with the router LED is that you have two states only.
"off" is steady on and "on" blinks. Therefore the wired LED is more
suitable.
Furthermore it reuses the correct switch configuration definition to
reflect the device ports and numbering. Additionally fixes the issue
that the default configuration is not applied as no port 6 exists on
this device.
Signed-off-by: Tobias Wolf <github-NTEO@vplace.de>
Factory image can be installed via Zyxel WebUI.
Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com>
[removed linux,modalias parameter from flash node in dts]
[removed sdhci node from dts; no sd card slot here]
Signed-off-by: Mathias Kresin <dev@kresin.me>
The Sitecom firmware upgrade file has SENAO_FIRMWARE_TYPE 2 set. This
looks rather wrong since SENAO_FIRMWARE_TYPE 2 is kernel only but the
file is way to big for only including a kernel.
The factory image need to have the dlf file extension. Otherwise the
Sitecom firmware rejects the file.
The stock firmware uses the following mac addresses:
LAN: 00:0C:F6:AA:BB:D8 (u-boot env: ethaddr)
2,4: 00:0C:F6:AA:BB:D8 (EEPROM)
5: 00:0C:F6:AA:BB:DC (EEPROM)
WAN: 00:0C:F6:AA:C8:43 (u-boot env: wanaddr)
Assuming the mac address range :D8 to :DC is reserved for this device,
the MAC addresses were reorder to have a unique MAC address for each
interface:
2.4GHz: 00:0C:F6:AA:BB:D8
LAN: 00:0C:F6:AA:BB:D9
WAN: 00:0C:F6:AA:BB:DA
5 GHz: 00:0C:F6:AA:BB:DC
The first MAC is assigned to the 2.4GHz WiFi interface
to keep compatibility with the SSIDs printed on the case, which have
the last three sextets of the MAC address appended.
There are still issues with the rt2x00 driver. It is not possible to
use both wireless interfaces at the same time. The 2.4 GHz
wireless (PCIe) only works if the internal 5GHz wireless is/has been
enabled or used for scanning. The internal 5GHz wireless only works if
the 2.4GHz wireless (PCIe) was never enabled. Disabling the 2.4Ghz
after it was enabled will result in stations seeing the 5Ghz AP but are
unable to connect.
Due to the not optimal working wifi the manufacture, backup and storage
partitions of the OEM firmware are kept for now to allow an easy switch
back to the Sitecom firmware.
Signed-off-by: Jasper Scholte <NightNL@outlook.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
Polling every 40ms causes more than 10% CPU load on weak devices. An
interval of 200ms is much more reasonable.
Signed-off-by: Martin Weinelt <martin@darmstadt.freifunk.net>
[Matthias Schiffer: adapt OpenWrt patch; add ramips; extend commit message]
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
The MikroTik hEX v3 (RB750Gr3) is a MT7621AT board which is similar to most MT7621 reference designs, it can be easily supported by this patch; however, the stock RouterBOOT bootloader has to be replaced by a MT7621 SDK U-Boot such as https://github.com/ndoo/RB750Gr3-U-Boot - U-Boot configured for the RB750Gr3 (16MiB SPI flash, 256MiB DDR3 RAM at 1200MHz).
RouterBOOT, the stock bootloader, does not initialize the UART and boots silently, making it preferable to replace it with a MT7621 SDK U-Boot with UART (57600 8N1) that supports HTTP, TFTP or serial upload of sysupgrade firmware and U-Boot.
Furthermore, RouterOS, the stock firmware, is contained in a proprietary modification of SquashFS without GPL sources; UART is also disabled in stock firmware.
The combination of LEDE firmware generated by this PR and MT7621 SDK U-Boot expects the printed MAC address to reside at offset `0xe000` of the factory partition (absolute offset is `0x4e000`); this is similar to the factory MAC address offset for several other MT7621 devices.
A 16MiB flash dump suitable for use with flashrom will be provided if/once this patch is accepted and binaries are built by LEDE buildbot. Alternatively, writing the U-Boot to the SPI flash starting at 0x0 offset and booting the board with serial console attached will allow TFTP, HTTP or serial upload of sysupgrade firmware.
Signed-off-by: Andrew Yong <me@ndoo.sg>
- setting read-only flag to important partitions
- enabling PA to improve 2.4 GHz signal strength
- add missing leds
- rename colour led
- add mac adress to 5GHz wlan interface
- included <dt-bindings/input/input.h> and <dt-bindings/gpio/gpio.h>
Signed-off-by: Henryk Heisig hyniu@o2.pl
Assign the reset functionality to the wps/reset buttons. Use the wlan
switch of the 6200n to enable/disable wlan.
Add the internet led of the 6200nl and use the led for boot status
indication
Signed-off-by: Mathias Kresin <dev@kresin.me>
With 3a9752bbd2 and later changes to
ramips_set_preinit_iface() the default vlan config applied during
preinit was changed. These changes were made without updating the
default network config to ensure that vlan interfaces used for lan/wan
are still configured.
Fix the issue by using the default all LAN portmap and disabling not
connected switch ports using portdisable device tree parameter.
Signed-off-by: Mathias Kresin <dev@kresin.me>
With de51026515 the explicit tagging of
the CPU port was removed. This leads to a not working default network
config, with vlans enabled but disabled CPU tagging, for boards where
all switch ports are having the same role.
In case the ports are having different roles set, tagging is is set
implicit for the CPU port by ucidef_add_switch().
Signed-off-by: Mathias Kresin <dev@kresin.me>
Don't set the lan/wan interface when using ucidef_add_switch. This
results into a wan interface albeit all ports a annotated as lan ports.
ucidef_add_switch takes care of setting the correct lan/wan interface
according to the annotation of the ports.
Signed-off-by: Mathias Kresin <dev@kresin.me>
applied bb-final-ramips-add-zyxel-nbg-419n2.patch from
123serge123, found at https://yadi.sk/d/1ZV0lKJwbTE65;
see https://forum.openwrt.org/viewtopic.php?pid=246905#p246905,
modified slightly to fit to CC release and to new lede build
system: image/rt305x.mk include file is used now
changed NBG-419N2.dts format to fit style of other dts files
Signed-off-by: Klaus <k-laus@quantentunnel.de>
- CPU: MT7620A 580MHz
- Flash: 8MB - RAM: 64MB
- External PA+LNA on both WLAN2.4 and WLAN5
- 4x LAN ethernet and 1x WAN ethernet
Signed-off-by: Xuefu Lin <xuefulin@gmail.com>
- quote the interface name
- remove call of not existing function
- remove the proto if it's the default proto
Signed-off-by: Mathias Kresin <dev@kresin.me>
Due to the missing phy-mode setting, the switch wasn't initialised.
The wireless requires an eeprom to work. Use the same mac addresses as
the stock firmware.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The AR8327 initvals were not copied to the DTS during the switch from
mach file to device tree and broke the switch on the device.
The former used PORT6 related initvals were wrong and have been
corrected.
The phy mode setting for the switch was missing in the DTS as well.
The wireless requires an eeprom to work. The dual band wireless chips
have both bands enabled by default but only one band per chip is
working.
The stock firmware uses the following mac addresses:
LAN: AA:BB:CC:DD:EE:E4
WAN: AA:BB:CC:DD:EE:E4
2.4GHz: AA:BB:CC:DD:EE:E4
5 GHz: AA:BB:CC:DD:EE:E8
Assuming the mac address range :E4 to :E8 is reserved for this device,
the MAC addresses were reorder to have a unique MAC address for each
interface:
LAN: AA:BB:CC:DD:EE:E4
2.4GHz: AA:BB:CC:DD:EE:E4
WAN: AA:BB:CC:DD:EE:E5
5 GHz: AA:BB:CC:DD:EE:E8
Signed-off-by: Mathias Kresin <dev@kresin.me>
Thunder Timecloud is a small NAS with MT7621A. It has 1 USB port and an
SD Card slot. There is no wireless cards.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
