The arm CPUs uses in the supported Mediatket SoCs have a FPU accordingly
to the datasheet, activate it also. The CPU subtype "neon-vfpv4" is
selected, but the toolcahin generated for this SoC will still be
compiled with soft float and not with the hard float ABI as we haven't
the fpu feature flag set. If this toolchain is reused by other targets
this will even affect other targets.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
When sourcing /sys/class/block/*/uevent values have to be quoted as
they may contain spaces (e.g. in PARTNAME).
Fix this by pre-processing with sed before sourcing.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The BDFs for OpenMesh A42 were upstreamed [1] to the ath10k-firmware
repository and are now part of ath10k-firmware 2018-01-26. The
ipq-wifi-openmesh_a42 package can now be dropped because OpenWrt already
ships the QCA4019 board-2.bin from this version.
[1] https://wireless.wiki.kernel.org/en/users/drivers/ath10k/boardfiles
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
* introduces the BDFs for the OpenMesh A42 in
/lib/firmware/ath10k/QCA4019/hw1.0/board-2.bin.
* adds new firmware firmware-6.bin_RM.4.4.1.c1-00037-QCARMSWP-1 for
QCA6174 hw3.0
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
COMFAST CF-E375AC is a ceiling mount AP with PoE support, based on
Qualcomm/Atheros QCA9563 + QCA9886 + QCA8337.
Short specification:
2x 10/100/1000 Mbps Ethernet, with PoE support
128MB of RAM (DDR2)
16 MB of FLASH
3T3R 2.4 GHz, 802.11b/g/n
2T2R 5 GHz, 802.11ac/n/a, wave 2
built-in 5x 3 dBi antennas
output power (max): 500 mW (27 dBm)
1x RGB LED, 1x button
built-in watchdog chipset
Flash instruction:
Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.
Signed-off-by: Ding Tengfei <dtf@comfast.cn>
With no warning, it just looks like the box has hung during boot.
We don't want users resetting it without having captured a crashdump.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
TP-Link Archer C50 v3 is a router with 5-port FE switch and
non-detachable antennas. It's based on MediaTek MT7628N+MT7612E.
Specification:
- MediaTek MT7628N/N (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- 4x external, non-detachable antennas
- UART (J1) header on PCB (115200 8n1)
- 7x LED (GPIO-controlled*), 2x button, power switch
* WAN LED in this devices is a dual-color, dual-leads type which isn't
(fully) supported by gpio-leds driver. This type of LED requires both
GPIOs state change at the same time to select color or turn it off.
For now, we support/use only the green part of the LED.
Flash instruction:
The only way to flash LEDE image in ArcherC50v3 is to use
tftp recovery mode in U-Boot:
1. Configure PC with static IP 192.168.0.66/24 and tftp server.
2. Rename "openwrt-ramips-mt7628-ArcherC50v3-squashfs-tftp-recovery.bin"
to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
the router and keep button pressed for around 6-7 seconds, until
device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
The D-Link devices with JBOOT bootloader use their own kernel
image header (stag + sch2 headers).
This driver find jImage header and set rootfs start after kernel file.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
This commit marks the CPUs switchport explicit as untagged.
Otherwise, an eth0.1 interface is created and the devices
LAN-ports are not working.
Signed-off-by: David Bauer <mail@david-bauer.net>
Compiling the Intel microcode package results in a
microcode.bin and a microcode-64.bin. As we can
decide based on the subtarget which should be used,
we'll only split the required .bin file with
iucode-tool.
x64 will get the intel-microcode-64.bin
All other variants will get intel-microcode.bin
The microcodes will be updated from preinit via a common
script - that's the earliest place where we can do it.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Use the Debian repository for sourcing the ucode files.
Current (20171205) includes support for fam17h CPUs already.
The microcodes will be updated from preinit via a common
script - that's the earliest place where we can do it.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Add tool to "compile" Intel microcode files. The tool will be
compiled for host (to split the microcode.dat) and for target
(to forcibly reload the microcode if required).
Instead of using the large microcode.bin/microcode-64.bin, the
splitted ucode files (separate for CPU families) will be
installed.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
When we provide the HOSTCFLAGS to the U-Boot build it will fail because
it can not find the u-boot provided header files any more.
Just overwrite and not append the package specific configuration on top
of the configuration provided by u-boot.mk.
uboot-fritz4040 is based on U-Boot 2012.07 and this problem is probably
similar to the problem seen with the lantiq and ar71xx u-boot build.
Fixes: df9781a420 ("u-boot,at91bootstrap: fix incorrect HOSTCPPFLAGS variable")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Use "$(DTS_DIR)", defined at include/image.mk, instead of
"$(LINUX_DIR)/arch/$(LINUX_KARCH)/boot/dts" in order to generalize and
allow a better Device/* device-tree parameterization (i.e. DEVICE_DTS_DIR
and DTS_DIR).
Signed-off-by: Adrià Llaudet <adria.llaudet@gmail.com>
Update Linux kernel version from 4.9 to 4.14 for archs38.
config-4.14 was simply regenerated with "make kernel_menuconfig".
Signed-off-by: Evgeniy Didin <Evgeniy.Didin@synopsys.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: John Crispin <john@phrozen.org>
Once installed fou kernel module allows you to use FOU (Foo over UDP)
and GUE (Generic UDP encapsulation) tunnel protocols.
To get ip fou command working you also need to install ip-full.
Signed-off-by: Filip Moc <lede@moc6.cz>
Since I have no openssl-dev on my machine, I first
get this error:
```
tools/kwbimage.c:21:10: fatal error: openssl/bn.h: No such file or directory
#include <openssl/bn.h>
```
After removing the UBOOT_MAKE_FLAGS the next error is:
```
tools/kwbimage.c:40:6: error: conflicting types for ‘EVP_MD_CTX_cleanup’
void EVP_MD_CTX_cleanup(EVP_MD_CTX *ctx)
```
After removing the OpenSSL patches the next error is:
```
HOSTLD tools/dumpimage
/usr/bin/ld: cannot find -lssl
/usr/bin/ld: cannot find -lcrypto
collect2: error: ld returned 1 exit status
scripts/Makefile.host:108: recipe for target 'tools/dumpimage' failed
make[5]: *** [tools/dumpimage] Error 1
```
So, the final part is to add the build system's
HOST_LDFLAGS to the UBOOT_MAKE_FLAGS.
(which was done in the previous commit)
Then the image builds.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
This will make sure that the build system's
paths for linking are available.
This is needed mostly for linking with tools/libressl.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
This would should up as `$$(HOSTCPPFLAGS)` in the host CFLAGS.
```
make --jobserver-fds=3,4 -j -C <openwrt>/build_dir/target-arm_cortex-a8+vfpv3_musl_eabi/u-boot-A10-OLinuXino-Lime/u-boot-2017.07 CROSS_COMPILE=arm-openwrt-linux-muslgnueabi- DTC="<openwrt>/build_dir/target-arm_cortex-a8+vfpv3_musl_eabi/linux-sunxi_cortexa8/linux-4.9.76/scripts/dtc/dtc" HOSTCC="gcc" HOSTCFLAGS='-O2 -I<openwrt>/staging_dir/host/include -I<openwrt>/staging_dir/host/usr/include -I<openwrt>/staging_dir/hostpkg/include -I<openwrt>/staging_dir/target-arm_cortex-a8+vfpv3_musl_eabi/host/include $$(HOSTCPPFLAGS)' HOSTLDFLAGS="" BL31=<openwrt>/staging_dir/target-arm_cortex-a8+vfpv3_musl_eabi/image/bl31.bin
```
And then it would complain with:
```
/bin/sh: 1: HOSTCPPFLAGS: not found
```
Also, HOSTCPPFLAGS does not exist.
The correct var is HOST_CPPFLAGS.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Activate the support for 64 bit on all 64 bit CPUs and not only x86_64.
ARM64 does not provide an xml file, so do not pack any.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This config option was renamed in upstream Linux commit 681bec0367
("tracing: Rename update the enum_map file")
Reported-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
We use the dtc from the kernel and that does not have all the options
which u-boot would like to use now. make these parameters optional.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
3413961 mt7603: avoid reordering qos-null data packets
c60e6db mt76: toggle driver station powersave bit before notifying mac80211
246d548 mt76: stop tx queues from the driver callback instead of common code
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The target it was meant for was updated to a version that this does not
compile with. It probably also hasn't been used in years
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Don't append an empty sendopts value as odhcp6c bails out
immediately on an empty -x option triggering an infinite start
loop of odhcp6c
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Commit a26045049b added support for sendopts as a string; since multiple
sendopts values can be specified it makes more sense to model it as a
list of strings.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Convert userspace code to use generic device-tree compatible board
detection method. Users of the existing code will have to use
sysupgrade -F once to switch to the new generic board naming.
Properly setup pinctrl fixing the switch port LEDs.
Fixes commit 9c4fe103cb (ramips: add support for ZBT-WE1226)
Reported-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
