Drop kmod-ledtrig-default-on and kmod-ledtrig-netdev as the kmod were
dropped and are now enabled by default.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This commit adds support for the Cisco Meraki MX64 and MX65 devices which
use the Broadcom NSP SoC, which is compatible with the bcm53xx platform.
MX64 Hardware info:
- CPU: Broadcom BCM58625 Cortex A9 @ 1200Mhz
- RAM: 2 GB (4 x 4Gb SK Hynix H5TC4G83CFR)
- Storage: 1 GB (Micron MT29F8G08ABACA)
- Networking: BCM58625 internal switch (5x 1GbE ports)
- USB: 1x USB2.0
- Serial: Internal header
MX65 Hardware info:
- CPU: Broadcom BCM58625 Cortex A9 @ 1200Mhz
- RAM: 2 GB (4 x 4Gb SK Hynix H5TC4G83CFR)
- Storage: 1 GB (Micron MT29F8G08ABACA)
- Networking: BCM58625 switch (2x 1GbE ports, used for WAN ports 1 & 2)
2x Qualcomm QCA8337 switches (10x 1GbE ports, used for LAN ports 3-12)
- PSE: Broadcom BCM59111KMLG connected to LAN ports 11 & 12
- USB: 1x USB2.0
- Serial: Internal header
Notes:
- The Meraki provided GPL source are available at [2].
- Wireless capability on the MX64W and MX65W exists in the form of 2x
Broadcom BCM43520KMLG, which is not supported. These devices will work
otherwise as standard MX64 or MX65 devices.
- Early MX64 units use an A0 variant of the BCM958625 SoC which lacks
cache coherency and uses a different "secondary-boot-reg". As a
consequence a different device tree is needed.
- Installation of OpenWrt requires changing u-boot to a custom version.
This is due to the stock u-boot "nand read" command being limited to
load only 2MB, in spite of the bootkernel1 and bootkernel2 partitions
both being 3MB in the stock layout. It is also required to allow
booting via USB, enabling cache coherency and setting up the QCA
switches and Serdes link on the MX65. The modified sources for U-boot
are available for the MX64[3] and MX65[4].
- Initial work on this device used a small bootloader within the OEM
partition scheme. To allow booting of larger kernels, UBI and bootm
support has been added, along with ability to store env variables to
the NAND. The Shmoo and newly created env partitions have been moved
to the extra space available after the nvram data.
- Users who installed the previous non-UBI supporting bootloader will
need to convert to the new one before flashing a compatible image.
These steps are detailed below.
References:
[1] https://www.broadcom.com/products/embedded-and-networking-processors/c
ommunications/bcm5862x
[2] https://dl.meraki.net/wired-14-39-mx64-20190426.tar.bz2
[3] https://github.com/clayface/U-boot-MX64-20190430_MX64
[4] https://github.com/clayface/U-boot-MX64-20190430_MX65
Installation guide:
Initial installation steps:
1. Compile or obtain OpenWrt files for the MX64 or MX65, including
u-boot[3][4], initramfs and sysupgrade images.
2. A USB disk with DOS partition scheme and primary FAT partition is
required.
3. If installing onto an MX64, set up a local web server.
4. On the device, boot into diagnostic mode by holding reset when
powering on the device. Continue to hold reset until the orange LED
begins to flash white. On used units the white flash may be difficult
to see.
5. Plug an Ethernet cable into the first LAN port, set the host to
192.168.1.2 and confirm telnet connectivity to 192.168.1.1.
U-boot installation - MX64 Only:
1. Newer fw versions require extra steps to support OpenWrt. To check,
please connect via telnet and run:
`cat /sys/block/mtdblock0/ro`
If the result is 1, your mtd0 is locked will need to perform extra
steps 4 and 5 in this section. If the result is 0 then skip these.
2. Check which SoC is in use by running the following command:
`devmem 0x18000000`
If devmem is not found then try:
`devmem2 0x18000000`
If the output begins with anything between "0x3F00-0x3F03" you will
need to use the A0 release. For any other output, eg "0x3F04" or
higher, use the regular MX64 image.
3 Confirm the size of the device's boot(mtd0) partition. In most
cases it should be 0x100000 or larger. If this is the case, please
proceed to use the uboot_mx64 image. If the reported size is
0x80000, please use the uboot_mx64_small image, then follow the
later guide to change to the larger image.
`cat /proc/mtd`
Example output:
`# cat /proc/mtd
cat /proc/mtd
dev: size erasesize name
mtd0: 00100000 00040000 "boot"
mtd1: 00080000 00040000 "shmoo"
mtd2: 00300000 00040000 "bootkernel1"
mtd3: 00100000 00040000 "nvram"
mtd4: 00300000 00040000 "bootkernel2"
mtd5: 3f700000 00040000 "ubi"
mtd6: 40000000 00040000 "all"`
4. Set up a webserver to serve the appropriate uboot_mx64 from the
following location and verify the SHA512:
https://github.com/clayface/U-boot-MX64-20190430_MX64
5. (Only if mtd0 is locked) You will also need the mtd-rw.ko kernel
module to unlock the partition from the same repo. An mtd executable
is also needed to write the mtd block. Place these on the web server
as well.
6. (Only if mtd0 is locked) Use wget to retrieve the files on the MX64:
`wget http://192.168.1.2/mtd-rw.ko`
`insmod mtd-rw.ko i_want_a_brick=1`
and confirm the unlock is set with dmesg
`mtd-rw: mtd0: setting writeable flag`
7. Download the appropriate u-boot image according to step 3. If you
did not need to unlock the mtd0 partition then use dd to write the
file, with caution:
`wget http://192.168.1.2/uboot_mx64`
`dd if=uboot_mx64 of=/dev/mtdblock0`
If you needed to unlock the mtd0 partition using the mtd-rw module,
run these commands instead to install u-boot instead:
`wget http://192.168.1.2/mtd`
`chmod +x mtd`
`wget http://192.168.1.2/uboot_mx64`
`./mtd write uboot_mx64 /dev/mtd0`
8. Once this has successfully completed, power off the device. If you
did not need to install the small u-boot image, proceed to
"OpenWrt Installation". Otherwise proceed to "UBI supporting
bootloader installation".
U-boot installation - MX65 Only:
1. Obtain telnet access to the MX65.
2. Confirm the size of the device's boot(mtd0) partition. In most
cases it should be 0x100000 or larger. If this is the case, please
proceed to use the uboot_mx65 image. If the reported size is
0x80000, please use the uboot_mx65_small image, then follow the
later guide to change to the larger image.
`cat /proc/mtd`
3. Prepare a USB drive formatted to FAT. Download the appropriate
uboot_mx65 to the USB drive from the following location and verify
the SHA512:
https://github.com/clayface/U-boot-MX64-20190430_MX65
3. Once you have telnet access to the MX65, plug in the USB disk and
run the following commands, with caution. The USB disk should
automount but if it does not, you will need to power off and on
again with reset held. Depending on step 2, use the uboot_mx65 or
uboot_mx65_small image accordingly:
`cd /tmp/media/sda1`
`dd if=uboot_mx65 of=/dev/mtdblock0`
4. Once this has successfully completed, power off the device. If you
did not need to install the small u-boot image, proceed to
"OpenWrt Installation". Otherwise proceed to "UBI supporting
bootloader installation".
UBI supporting bootloader installation:
These steps need to be followed if the older u-boot image was
installed, either because the Meraki diagnostic partition scheme used
0x80000 as the mtd0 size, or because you installed the u-boot provided
while OpenWrt support was still under development. If using OpenWrt,
please make a backup before proceeding.
1. Obtain the relevant image from the MX64(A0) or MX65 u-boot repo:
`openwrt-bcm5862x-generic-meraki_XXXX-initramfs-kernel.bin`
2. With the USB drive already inserted, power on the device while
holding the reset button. A white/orange flashing pattern will
occur shortly after power on. Let go of the reset button. The
device is now booting into OpenWrt initramfs stored on the USB
disk.
3. Connect by SSH to 192.168.1.1 and flash the embedded u-boot image,
changing X as appropriate:
`mtd write /root/uboot_mx6X /dev/mtd0`
You do not need to reboot as this image can handle "Kernel-in-UBI"
OpenWrt installation.
4. You can proceed to obtain and flash the appropriate OpenWrt image
at "OpenWrt Installation" Step 3.
5. Reboot will take significantly longer due to Shmoo calibration. In
case the device does not come online after several minute, power-
cycle the device and see if it boots. If you see an orange/white
flashing pattern, this indicates UBI booting was not successful and
you will need to copy a new bcm53xx image to a USB disk before
booting it and attempting to install OpenWrt again - refer to
"OpenWrt Installation" step 1. Do not attempt to reflash u-boot in
this scenario.
OpenWrt Installation:
1. Having obtained an OpenWrt image, please copy the file
`openwrt-bcm53xx-generic-meraki_XXXX-initramfs.bin`
to the base directory of a FAT formatted USB drive using DOS
partition scheme ,where XXXX is mx64, mx64_a0 or mx65 depending on
which device you have.
2. With the USB drive already inserted, power on the device. Boot time
will be longer than usual while Shmoo calibration takes place. A
different white/orange flashing pattern will eventually occur to
indicate device is now booting into OpenWrt initramfs stored on the
USB disk.
3. Ensuring Ethernet is plugged into a LAN port with IP set in the
192.168.1.0/24 subnet excluding 192.168.1.1, use SCP to copy the
sysupgrade file to 192.168.1.1:/tmp, eg:
`scp openwrt-bcm53xx-generic-meraki_XXXX-squashfs.sysupgrade.bin\
192.168.1.1:/tmp`
4. Connect by SSH to 192.168.1.1 and run sysupgrade:
`sysupgrade \
/tmp/openwrt-bcm53xx-generic-meraki_XXXX-squashfs.sysupgrade.bin`
5. OpenWrt should now be installed on the device.
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
[ Rebase kernel configuration for 6.6,
fix failsafe by making kmod-eeprom-at24 and kmod-dsa-qca8k built-in,
resolve conflicts,
add LED aliases,
fix eth0 MAC address at probe ]
TODO:
- fix multiple LED colors not applied despite aliases - due to custom
/etc/diag.sh
- fix race condition between preinit and probing of the DSA tree,
causing no network interface available in failsafe mode (in general
case - to allow moving drivers back to modules)
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16634
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Enable support for qca8k switch used in Meraki MX65. This is required to
properly support preinit networking on this device, otherwise unit won't
be accessible in failsafe mode.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16634
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is required for the AT24 EEPROM holding MAC address on Meraki
devices to probe before preinit starts, so all network devices can be
available at the preinit network setup starts
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16634
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Meraki MX6x devices use them to store MAC address, so it is required to be
built-in for networking to probe properly, before preinit network setup
happens, which in turn is required for proper failsafe mode access.
Enable CONFIG_EEPROM_AT24 for the target.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16634
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch is required to support reading MAC address on Meraki MX64/65
line of devices, but also touches MR32, so let's backport it first.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16634
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch adds "REQUIRE_IMAGE_METADATA=1" requirement for the MR26 and
MR32, with REQUIRE_IMAGE_METADATA explicitly 0 elsewhere. This is based
upon bcm63xx's base-files/lib/upgrade/platform.sh.
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16634
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Drop config and files for Linux 6.1.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16103
Signed-off-by: Robert Marko <robimarko@gmail.com>
Drop config and files for Linux 5.15.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16103
Signed-off-by: Robert Marko <robimarko@gmail.com>
Switch to Linux kernel version 6.6.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16103
Signed-off-by: Robert Marko <robimarko@gmail.com>
Kernel 6.6 checks for orphan sections and prints a warning about them,
which in turn will make CI fails as we have Werror enabled there.
Issue is that cache-v7-min.S produces .init.text section which is an
orphan section since it is not being handled by the vmlinux.lds.S linker
script.
So, lets put the generated .init.text section under .text.
Fixes: f0d8ce4f48 ("bcm53xx: add testing support for kernel 6.6")
Signed-off-by: Robert Marko <robimarko@gmail.com>
Backport two commits from Linux 6.3 wiring up device node parents of
ubi devices (pointing to their MTD parent) as well as ubiblock devices
(poiting to their parent UBI volume).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This will help switching to newer 5.15 kernels. This backport required
rebasing Northstar's USB host patch.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Among other changes this commit makes Linux use correct switch ports
again.
Fixes: a4792d79e8 ("bcm53xx: backport DT changes from v6.5")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
1) clear nvram partialboots upon successful boot
This behavior is already defined for EA9500; enabled for EA9200 too.
2) fix MAC address in board.d/02_network
Use the correct nvram variable to derive lan/wan MAC address.
Signed-off-by: Rani Hod <rani.hod@gmail.com>
So far every build of a single bcm53xx Target Profile (it means: when
NOT using CONFIG_TARGET_MULTI_PROFILE) resulted in all target devices
images being built. Now it only builds the one matching selected
profile.
Fixes: #13572
Suggested-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: Rani Hod <rani.hod@gmail.com>
[rmilecki: update commit subject + body & move PROFILES line]
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The DIR-890L is very similar to DIR-885L, but has both USB2
and USB3. The signature for the wrgac36 board was copied from
DD-Wrt.
The DIR-890L bootstrap will only load the first 2 MB after
the SEAMA header in the NAND flash, uncompress it with LZMA
and execute it. Since the compressed kernel will not fit in
2 MB we have a problem. Solve this by putting a LZMA
compressed U-Boot into the first 128 KB of the flash
followed by the kernel. The bootstrap will then uncompress
and execute U-Boot and then we let U-Boot read the kernel
from flash and execute it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
ASUS RT-AC3100 is ASUS RT-AC88U without the external switch.
OpenWrt forum users effortless and ktmakwana have confirmed that there are
revisions with either 4366b1 or 4366c0 wireless chips.
Therefore, include firmware for 4366b1 along with 4366c0. This way, all
hardware revisions of the router will be supported by having brcmfmac use
the firmware file for the wireless chip it detects.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
