Hardware specification:
SoC: MediaTek MT7981B 2x A53
Flash: ESMT F50L1G41LB 128MB
RAM: NT52B128M16JR-FL 256MB
Ethernet: 4x 10/100/1000 Mbps
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset, Mesh
Power: DC 12V 1A
Flash instructions:
1. Get ssh access
Check this link: https://forum.openwrt.org/t/openwrt-support-for-xiaomi-ax3000ne/153769/22
2. Backup import partitions
```
dev: size erasesize name
mtd1: 00100000 00020000 "BL2"
mtd2: 00040000 00020000 "Nvram"
mtd3: 00040000 00020000 "Bdata"
mtd4: 00200000 00020000 "Factory"
mtd5: 00200000 00020000 "FIP"
mtd8: 02200000 00020000 "ubi"
mtd9: 02200000 00020000 "ubi1"
mtd12: 00040000 00020000 "KF"
```
Use these commands blow to backup your stock partitions.
```
nanddump -f /tmp/BL2.bin /dev/mtd1
nanddump -f /tmp/Nvram.bin /dev/mtd2
nanddump -f /tmp/Bdata.bin /dev/mtd3
nanddump -f /tmp/Factory.bin /dev/mtd4
nanddump -f /tmp/FIP.bin /dev/mtd5
nanddump -f /tmp/ubi.bin /dev/mtd8
nanddump -f /tmp/KF.bin /dev/mtd12
```
Then, transfer them to your computer via scp, netcat, tftp
or others and keep them in a safe place.
3. Setup Nvram
Get the current stock: `cat /proc/cmdline`
If you find `firmware=0` or `mtd=ubi`, use these commands:
```
nvram set boot_wait=on
nvram set uart_en=1
nvram set flag_boot_rootfs=1
nvram set flag_last_success=1
nvram set flag_boot_success=1
nvram set flag_try_sys1_failed=0
nvram set flag_try_sys2_failed=0
nvram commit
```
If you find `firmware=1` or `mtd=ubi1`, use these commands:
```
nvram set boot_wait=on
nvram set uart_en=1
nvram set flag_boot_rootfs=0
nvram set flag_last_success=0
nvram set flag_boot_success=1
nvram set flag_try_sys1_failed=0
nvram set flag_try_sys2_failed=0
nvram commit
```
4. Flash stock-initramfs-factory.ubi
If you find `firmware=0` or `mtd=ubi`:
`ubiformat /dev/mtd9 -y -f /tmp/stock-initramfs-factory.ubi`
If you find `firmware=1` or `mtd=ubi1`:
`ubiformat /dev/mtd8 -y -f /tmp/stock-initramfs-factory.ubi`
Then reboot your router, it should boot to the openwrt
initramfs system now.
5. Setup uboot-env
Now it will be setup automatically in upgrade process,
you can skip this step.
If your `fw_setenv` did not work, you need run this command:
`echo "/dev/mtd1 0x0 0x10000 0x20000" > /etc/fw_env.config`
Then setup uboot-env:
```
fw_setenv boot_wait on
fw_setenv uart_en 1
fw_setenv flag_boot_rootfs 0
fw_setenv flag_last_success 1
fw_setenv flag_boot_success 1
fw_setenv flag_try_sys1_failed 8
fw_setenv flag_try_sys2_failed 8
fw_setenv mtdparts "nmbm0:1024k(bl2),256k(Nvram),256k(Bdata),
2048k(factory),2048k(fip),256k(crash),256k(crash_log),
34816k(ubi),34816k(ubi1),32768k(overlay),12288k(data),256k(KF)"
```
6. Flash stock-squashfs-sysupgrade.bin
Use shell command:
`sysupgrade -n /tmp/stock-squashfs-sysupgrade.bin`
Or go to luci web.
If you need to change to Openwrt U-Boot layout, do next. If you
do not need, please ignore it.
Change to OpenWrt U-Boot:
1. Flash ubootmod-initramfs-factory.ubi
Check mtd partitions: `cat /proc/mtd`
```
mtd7: 00040000 00020000 "KF"
mtd8: 02200000 00020000 "ubi_kernel"
mtd9: 04e00000 00020000 "ubi"
```
Run following command:
`ubiformat /dev/mtd8 -y -f /tmp/ubootmod-initramfs-factory.ubi`
Then reboot your router, it should boot to the openwrt initramfs
system now.
2. Check mtd again
```
mtd7: 00040000 00020000 "KF"
mtd8: 07000000 00020000 "ubi"
```
Make sure mtd8 is ubi.
3. Install kmod-mtd-rw
Run command: `opkg update && opkg install kmod-mtd-rw`
Or get it in openwrt server, or build it yourself, then install
it manually
Then run this command:
`insmod /lib/modules/$(uname -r)/mtd-rw.ko i_want_a_brick=1`
4. Clean up pstore
Run Command: `rm -f /sys/fs/pstore/*`
5. Format ubi and create new ubootenv volume
```
ubidetach -p /dev/mtd8; ubiformat /dev/mtd8 -y; ubiattach -p /dev/mtd8
ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB
ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB
```
6. (Optional) Add recovery boot feature.
```
ubimkvol /dev/ubi0 -n 2 -N recovery -s 10MiB
ubiupdatevol /dev/ubi0_2 /tmp/ubootmod-initramfs-recovery.itb
```
7. Flash Openwrt U-Boot
```
mtd write /tmp/ubootmod-preloader.bin BL2
mtd write /tmp/ubootmod-bl31-uboot.fip FIP
```
6. Flash ubootmod-squashfs-sysupgrade.itb
Use shell command:
`sysupgrade -n /tmp/ubootmod-squashfs-sysupgrade.itb`
Or go to luci web.
Now everything is done, Enjoy!
Go Back to stock from Openwrt U-Boot:
1. Force flash ubootmod-initramfs-recovery.itb
Use shell command:
`sysupgrade -F -n /tmp/ubootmod-initramfs-recovery.itb`
Or go to luci web.
Then it should boot to the openwrt initramfs system now.
2. Format ubi and Nvram
```
ubidetach -p /dev/mtd8; ubiformat /dev/mtd8 -y; ubiattach -p /dev/mtd8
mtd erase Nvram
```
3. Install kmod-mtd-rw
Run command: `opkg update && opkg install kmod-mtd-rw`
Or get it in openwrt server, or build it yourself, then install
it manually
Then run this command:
`insmod /lib/modules/$(uname -r)/mtd-rw.ko i_want_a_brick=1`
4. Flash stock U-Boot and ubi
```
mtd write /tmp/BL2.bin BL2
mtd write /tmp/FIP.bin FIP
mtd write /tmp/ubi.bin ubi
```
Then reboot your router, waiting it finished rollback in minutes.
Go Back to stock from stock layout Openwrt:
Just run command: `ubiformat /dev/mtd8 -y -f /tmp/ubi.bin`
Then reboot your router, waiting it finished rollback in minutes.
Notes:
1. Openwrt U-Boot and ubootmod openwrt did not enable NMBM.
Please make your backup safe.
Signed-off-by: Hank Moretti <mchank9999@gmail.com>
Hardware
--------
SOC: MediaTek MT7986A
RAM: 1GB DDR4
FLASH: 4GB eMMC
WiFi: 2x2 2.4 GHz 802.11 b/g/n/ax MT7916 DBDC
4x4 5 GHz 802.11 a/n/ac/ax MT7986
2x2 6 GHz 802.11ax MT7916 DBDC
ETH: 4x LAN 1Gbit/s (MT7531)
1x WAN 2.5Gbit/s (GPY211)
BTN: RESET, WPS
LED: Antenna LEDs (GPIO)
Mood-LED (Kinetic KTD2601) - unsupported
UART: Header nest to USB port - 3V3 115200 8N1
[BUTTON] GND - RX - TX [USB]
Installation
------------
1. Connect to the device using serial console.
2. Interrupt the Autoboot process when promted by sending '0' twice.
3. Serve the OpenWrt initramfs image using TFTP at 192.168.1.66. Name
the image "predator.bin" and conenct the TFTP server to the routers
LAN port.
4. Configure U-Boot to allow loading unsigned images from MMC
$ setenv bootcmd 'mmc read 0x40000000 0x00004400 0x0010000;
fdt addr $(fdtcontroladdr); fdt rm /signature; bootm 0x40000000';
saveenv
5. Transfer the image from U-Boot
$ setenv serverip 192.168.1.66; setenv ipaddr 192.168.1.1;
tftpboot 0x46000000 predator.bin; fdt addr $(fdtcontroladdr);
fdt rm /signature; bootm
6. Wait for OpenWrt to boot
7. Transfer the OpenWrt sysupgrade image to the router using scp.
8. Install OpenWrt using sysupgrade.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 7e7eb5312d)
Since 2021.07 multiple bugs were introduced that made it impossible to
create a bootable target for mvebu. Those issues should be now fixed since
2023.07-rc1.
References: #11661
Signed-off-by: Oli Ze <olze@trustserv.de>
Reviewed-by: Robert Marko <robimarko@gmail.com>
Tested-by: Andre Heider <a.heider@gmail.com> # espressobin-v3-v5-1gb-2cs
Signed-off-by: Petr Štetiar <ynezz@true.cz> [facelift]
(cherry picked from commit ba7d6dddc7)
It seems that DSA-based b53 driver never worked with BCM53573 SoCs and
BCM53125.
In case of swconfig-based b53 this fixes a regression. Switching bgmac
from using mdiobus_register() to of_mdiobus_register() resulted in MDIO
device (BCM53125) having of_node set (see of_mdiobus_register_phy()).
That made downstream b53 driver read invalid data from DT and broke
Ethernet support.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 79fd3e62b4)
new versions of the device have NAND with 8bit ECC
which was not yet supported before. This change removes
ECC restrictions.
Signed-off-by: Alexander Friese <af944580@googlemail.com>
(cherry picked from commit 6b11f0ec83)
8667347 build: allow passing SOVERSION value for dynamic library
Also adjust packaging of the library to only ship the SOVERSION
suffixed library object, to allow for concurrent installation of
ABI-incompible versions in the future.
Fixes: #13082
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
(cherry picked from commit 4af0a72a65)
U-Boot with enabled secure-boot will not boot images with the
@-character used for hash node-names.
Use the existing separation character configurable for each device.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 2b133ab19c)
Hardware
--------
CPU: Qualcomm IPQ4018
RAM: 256M
Flash: 16MB SPI-NOR (W25Q128)
128MB SPI-NAND (XTX)
WiFi: 2T2R (2GHz 802.11n ; 5 GHz 802.11ac)
ETH: 4x LAN ; 1x WAN (Gigabit)
CELL: Quectel RG501Q 3G/4G/5G
UART: Available on the goldfinger connector (Pinout silkscreened)
115200 8N1 3V3 - Only connect RX / TX / GND
Installation
------------
1. Enable SSH in the Teltonika UI
(System --> Administration --> Access Control)
2. Check from which partition set the device is currently running from.
$ cat /proc/boot_info/rootfs/primaryboot
In case this output reads 0, install a Software update from Teltonika
first. After upgrade completion, check this file now reads 1 before
continuing.
2. Transfer the OpenWrt factory image to the device using scp. Use the
same password (user root!) as used for the Web-UI.
$ scp -O openwrt-factory.bin root@192.168.1.1:/tmp
3. Connect to the device using ssh as the root user.
4. Install OpenWrt by writing the factory image to flash.
$ ubiformat /dev/mtd16 -y -f /tmp/openwrt-factory.bin
5. Instruct the bootloaer to boot from the first partition set.
$ echo 0 > /proc/boot_info/rootfs/primaryboot
$ cat /proc/boot_info/getbinary_bootconfig > /tmp/bootconfig.bin
$ cat /proc/boot_info/getbinary_bootconfig1 > /tmp/bootconfig1.bin
$ mtd write /tmp/bootconfig.bin /dev/mtd2
$ mtd write /tmp/bootconfig1.bin /dev/mtd3
6. Reboot the device.
$ reboot
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 844bb4bfad)
At least Fedora and RHEL 9 set RSAMinSize=2048, so when trying to use
failsafe, we get 'Bad server host key: Invalid key length'
To workaround the issue, we can use: ssh -o RSAMinSize=1024 ...
Generating 2048 bits RSA is extremely slow, so add ed25519.
We keep RSA 1024 to be as compatible as possible.
Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com>
(cherry picked from commit 6ac61dead9)
Changelog from quic:
Bug fixes, stability improvements from previous releases
are present. There are no backward comatibility issues
with this release.
Tested-by: Michał Kwiatek <michal@kwiatek.it> # Xiaomi AX3600
Signed-off-by: Michał Kwiatek <michal@kwiatek.it>
[ improve commit description ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 1c56801dd2)
These are used by both the armsr (EFI boot) and
layerscape targets for phylink-controlled SFP
support on NXP DPAA2 platforms (LS1088,LS2088,LX2160).
This is in place of commit a7bd96c98f
("layerscape: add patches for SFP support on DPAA2 platforms")
in the main branch. armsr in main started at kernel 6.1
so there is not an equivalent 5.15 commit to cherry pick.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
All the tools (e.g fw_setenv, ubiupdatevol) and config (fw_env.config)
needed for sysupgrade are already included in /lib/upgrade/stage2
Signed-off-by: Mathew McBride <matt@traverse.com.au>
(cherry picked from commit 094c37708a)
The Traverse LS1043 boards were not publicly released,
all the production has been going to OEM customers who
do not use the image format defined in the OpenWrt tree.
Only a few samples were circulated outside Traverse
and our OEM customers. The public release (then called
Five64) of this series was cancelled in favour of our
LS1088A based design (Ten64).
It is best to remove these boards to avoid wasting
OpenWrt project and contributor resources.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
(cherry picked from commit 8e7ba6fbae)
The Ten64 board[1] is based around NXP's Layerscape LS1088A SoC.
It is capable of booting both standard Linux distributions
from disk devices, using EFI, and booting OpenWrt
from NAND.
See the online manual for more information, including the
flash layout[2].
This patchset adds support for generating Ten64 images
for NAND boot.
For disk boot, one can use the EFI support that was
recently added to the armvirt target.
We previously supported NAND users by building
inside our armvirt/EFI target[3], but this approach
is not suitable for OpenWrt upstream. Users who
used our supplied NAND images will be able to upgrade
to this via sysupgrade.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
[1] - https://www.traverse.com.au/hardware/ten64
[2] - https://ten64doc.traverse.com.au/hardware/flash/
[3] - Example:
285e4360e1
(cherry picked from commit af0546da34)
If dual-stack configuration is in use, and dhcpv6 option is set, do not start
464xlat sub-interface for dhcpv6 sub-interace , as the configuration already
provides IPv4 connectivty, be it through single or dual APN configuration.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
(cherry picked from commit a9237c1af9)
Add two new "v6apn" and "v6profile" properties, to support split-APN
dual-stack onfiguration. This extends the existing ipv4v6 PDP type,
allowing simultaneous connection to two distinct APNs,
one for IPv4 and one for IPv6.
The parameters override existing 'apn' and 'profile' respectively,
if set, but only for IPv6 part of the connection.
If unset, they default to their original values, constituting a standard
IPv4v6 setup.
If a different APN is set for IPv6, a corresponding profile MUST also be
configured, with a different ID, than the IPv4 profile, for example,
profile 2.
Both APNs must match ones configured through QMI or through 'AT+CGDCONT'
command.
Example configuration in UCI:
config interface 'wan'
option proto 'qmi'
option device '/dev/cdc-wdm0'
option autoconnect '1'
option pdptype 'ipv4v6'
option apn 'internet'
option v6apn 'internetipv6'
option profile '1'
option v6profile '2'
Corresponding profile configuration:
AT+CGDCONT?
+CGDCONT: 1,"IP","internet","0.0.0.0",0,0,0,0
+CGDCONT: 2,"IPV6","internetipv6","0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0",0,0,0,0
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
(cherry picked from commit 48e8bf1b8f)
This patch will only force mac80211 loss detection upon ath10k by
masking the driver-specific loss-detection bit.
Ref: commit ed816f6ba8 ("mac80211: always use mac80211 loss detection")
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit d9070f8d23)
[felix.bau@gmx.de: replace path 6.2 with 5.15, refresh patches]
Signed-off-by: Felix Baumann <felix.bau@gmx.de>
The mdio bus is used to control externel switch. In most cases, they are
disabled, which is the normal behavior. Treating this as an error makes
no sense, so we need to change the notification level from error to info.
Fixes: a2acdf9607 ("ramips: mt7620: remove useless GMAC nodes")
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
(cherry picked from commit 285f0668f4)
This commit adds headers to the patches, so they can be applied with the
git am command.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
(cherry picked from commit 5d51079fd0)
53edfc7aaa34 wifi: mt76: mt7603: fix beacon interval after disabling a single vif
7ef4dd12d982 wifi: mt76: mt7603: fix tx filter/flush function
152608a40aa7 wifi: mt76: mt7615: do not advertise 5 GHz on first phy of MT7615D (DBDC)
cacac3902a63 wifi: mt76: split get_of_eeprom in subfunction
cd3dfe392769 wifi: mt76: add support for providing eeprom in nvmem cells
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 4395236a10)
The maximum offset that can be supported is 0x20000000
Do not override it to to something bigger than that on MT7621, as that could
cause issues based on the fixed memory mappings. This makes the last 64 MB
RAM unusable on MT7621 devices with 512 MB but avoids incurring a heavy
performance hit
Fixes: cd2b74e01e ("ramips: mt7621: disable highmem support and remove highmem offset patch")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit a110de8152)
Hardware
--------
CPU: Mediatek MT7981
RAM: 512M DDR4
FLASH: 256M NAND
ETH: MaxLinear GPY211 (2.5GbE N Base-T)
WiFi: Mediatek MT7981 (2.4GHz 2T2R:2 5GHz 3T3R:2 802.11ax)
BTN: 1x Reset
LED: 1x Multi-Color
UART Console
------------
Available below the rubber cover next to the ethernet port.
Settings: 115200 8N1
Layout:
<12V> <LAN> GND-RX-TX-VCC
Logic-Level is 3V3. Don't connect VCC to your UART adapter!
Installation Web-UI
-------------------
Upload the Factory image using the devices Web-Interface.
As the device uses a dual-image partition layout, OpenWrt can only
installed on Slot A. This requires the current active image prior
flashing the device to be on Slot B.
In case this is not the case, OpenWrt will boot only one time, returning
to the ZyXEL firmware the second boot.
If this happens, first install a ZyXEL firmware upgrade of any version
and install OpenWrt after that.
Installation TFTP / Recovery
----------------------------
This installation routine is especially useful in case of a bricked
device.
Attach to the UART console header of the device. Interrupt the boot
procedure by pressing Enter.
The bootloader has a reduced command-set available from CLI, but more
commands can be executed by abusing the atns command.
Boot a OpenWrt initramfs image available on a TFTP server at
192.168.1.66. Rename the image to nwa50axpro-openwrt-initramfs.bin.
$ atnf nwa50axpro-openwrt-initramfs.bin
$ atna 192.168.1.88
$ atns "192.168.1.66; tftpboot; setenv fdt_high 0xffffffffffffffff;
bootm"
Upon booting, set the booted image to the correct slot:
$ zyxel-bootconfig /dev/mtd9 get-status
$ zyxel-bootconfig /dev/mtd9 set-image-status 0 valid
$ zyxel-bootconfig /dev/mtd9 set-active-image 0
Copy the OpenWrt sysupgrade image to the device using scp.
Write the sysupgrade image to NAND using sysupgrade.
$ sysupgrade -n image.bin
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit f0445746f6)
U-Boot complains that the overlayed DT needs relocation, so set
DEVICE_DTS_LOADADDR to have it relocated.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit b1d10e0174)
removed redundant eeprom partition nodes from
cn7130_ubnt_edgerouter-4.dts and cn7130_ubnt_edgerouter-6p.dts
as they are identically defined in cn7130_ubnt_edgerouter-e300.dtsi.
Signed-off-by: Carsten Spieß <mail@carsten-spiess.de>
(integrated eeprom referenced node in the .dtsi)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit 700f11aaad)
The MAC addresses should be read from 3rd MTD partition,
but only two MTD partitions are populated.
To fix it, a partitions node has to surround the partition
nodes in device tree.
Tested with Edgerouter 6P
Signed-off-by: Carsten Spieß <mail@carsten-spiess.de>
(fixed checkpatch complains)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit 2b1d7965c7)
LEDs on Edgerouter 6P didn't work correctly:
blue /white LED swapped, on/off state inverted
Fixed in device tree:
swap the GPIO ports for power:blue and power:white LEDs
change LED activity from LOW to HIGH
Tested on Edgerouter 6P
Signed-off-by: Carsten Spieß <mail@carsten-spiess.de>
(cherry picked from commit 9009672930)
Some device recipes remove default target packages. If user tries to add
them back they will be ignored, since packages list is processed in one
go. Process the device recipe packages first and do user ones later, so
additions won't get filtered out.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
(cherry picked from commit e40b9a7fa0)
'help' target fails not finding a file, so follow up on a change[2] made
as a fix for main README[1].
1. d0113711a3 ("README: port to 21st century")
2. 751486b31f ("build: fix README.md reference after rename")
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
(cherry picked from commit 2d5f7035cf)
(cherry picked from commit e9911f10e4)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Instead of loading the whole image into the memory when generating the
sha256 sum, we load the file in chunks and update the hash incrementally
to avoid MemoryError in python. Also remove a stray empty line.
Fixes: #13056
Signed-off-by: Adones Pitogo <pitogo.adones@gmail.com>
(mention empty line removal, adds Fixes from PR)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit bdb4b78210)
there's a new symbol NVMEM_IMX_OCOTP_ELE that needs to be defined.
otherwise the build will fail:
| i.MX On-Chip OTP Controller support (NVMEM_IMX_OCOTP_ELE) [N/m/y/?] (NEW)
| make[6]: *** [scripts/kconfig/Makefile:77: syncconfig] Error 1
| make[5]: *** [Makefile:628: syncconfig] Error 2
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
DT overlays do not need relocation in order to be applied, so drop
defining the load address for dtbos.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit cff3786bd5)
The side-effect and main motivation is to also drop the FIT structure size
limit because with multiple device tree overlays it may easily grow beyond
the previous 4kB limit in the future.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 98e3f82c3f)
The PHY driver now uses regmap created from pio syscon, we no longer
need the boottrap device.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit f321a49fd5)
Backport in-SoC Gigabit Ethernet PHY driver instead of carrying the
driver in files-5.15.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 9fac590096)
The PHY driver needs to read a register containing the values of the
bootstrap pins (which happen to be the PHY LEDs) to determine the LED
polarities. Allow regmap access to first pinctrl bank by adding the
'syscon' compatible, and reference the pinctrl in the MDIO bus where
the PHY driver will look for it.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 1f1e0b1144)
