This fixes building with USE_LTO enabled.
<artificial>:(.text+0xc22): relocation R_MIPS16_26 against `libxt_DNAT_init' cannot be used when making a shared object; recompile with -fPIC
./openwrt/staging_dir/toolchain-mips_24kc_gcc-12.3.0_musl/lib/gcc/mips-openwrt-linux-musl/12.3.0/../../../../mips-openwrt-linux-musl/bin/ld.bfd: non-dynamic relocations refer to dynamic symbol printf
./openwrt/staging_dir/toolchain-mips_24kc_gcc-12.3.0_musl/lib/gcc/mips-openwrt-linux-musl/12.3.0/../../../../mips-openwrt-linux-musl/bin/ld.bfd: failed to set dynamic section sizes: bad value
collect2: error: ld returned 1 exit status
Signed-off-by: Anari Jalakas <anari.jalakas@gmail.com>
This fixes building with USE_LTO enabled.
<artificial>:(.text+0x400c): relocation R_MIPS16_26 against `iwinfo_close' cannot be used when making a shared object; recompile with -fPIC
./openwrt/staging_dir/toolchain-mips_24kc_gcc-12.3.0_musl/lib/gcc/mips-openwrt-linux-musl/12.3.0/../../../../mips-openwrt-linux-musl/bin/ld.bfd: non-dynamic relocations refer to dynamic symbol strcpy
./openwrt/staging_dir/toolchain-mips_24kc_gcc-12.3.0_musl/lib/gcc/mips-openwrt-linux-musl/12.3.0/../../../../mips-openwrt-linux-musl/bin/ld.bfd: failed to set dynamic section sizes: bad value
collect2: error: ld returned 1 exit status
Signed-off-by: Anari Jalakas <anari.jalakas@gmail.com>
d8118f6 config: make sure timer is not on the timeouts list before freeing
4bbc6e7 add hostsfile output in addition to statefile
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
c8c9f10 uim: fix help formatting
aac0776 uqmi: add APN profile commands
ffc5eea uim: support SIM card power-up/down
d6c963d uim: add application state to SIM status
Signed-off-by: David Bauer <mail@david-bauer.net>
The option 31 in the RA specifies the DNS search list, the support
to configure this via UCI is missing in case dnsmasq-dhcpv6 is used.
This commit uses the uci option domain (same as is done by odhcpd) to
read and pass the DNS search list to dnsmasq, which is then used by RA.
Hence, with this commit, we are able to configure DNS search list for the
RA messages via the uci config when dnsmsaq-dhcpv6 is used.
Signed-off-by: Rahul Thakur <rahul.thakur@iopsys.eu>
479c7f8676d9 cache: make record/hostname lookup case-insensitive
26c97a5a50bf ubus: add a browse flag for suppressing cached ip addresses
c286c51a9bd9 Fix AVL tree traversal in cache_record_find and cache_host_is_known
4035fe42df58 interface: use a global socket instead of per-interface ones
c63d465698c7 cache: dump hostname target from srv records
b42b22152d73 use hostname from SRV record to look up IP addresses
d45c443aa1e6 ubus: add array flag support for the hosts method
Signed-off-by: Felix Fietkau <nbd@nbd.name>
There are a few targets that mess with the atm kernel headers. To avoid
incompatibility between kernel and user space during compilation, the
correct headers should be used.
Consequently, the package must also be marked as nonshared.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Modems which are using qmi do not reply on the 1st sync but they do
on subsequent. So qmi.sh is hanging on the first call. Since 2020 uqmi
supports a timeout parameter. Unfortunately qmi.sh didn't make use of
this parameter. So qmi.sh is now invoking an early dummy access to
unlock the modem
Signed-off-by: Uwe Niethammer <uwe@dr-niethammer.de>
Recent hostapd changes just edited the ucode files. It is required to
bump the PKG_RELEASE to include the newest changes in the latest builds.
Signed-off-by: Nick Hainke <vincent@systemli.org>
If the full interface is restarted while bringing up an AP, it can trigger a
wpa_supplicant interface start before wpa_supplicant is notified of the
allocated mac addresses.
Fix this by moving the iface_update_supplicant_macaddr call to just after
the point where mac addresses are allocated.
Reported-by: Michael-cy Lee (李峻宇) <Michael-cy.Lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In the dnsmasq init script, an off-by-one in the range calculation of
ipcalc.sh was mitigated by passing the limit as if its counting started
at zero. This patch removes the mitigation as the off-by-one has been
fixed.
Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
Add a function 'ipcalc' to /lib/functions.sh that sets variables more
safely using export.
With this new function, dnsmasq also handles the return value of ipcalc
correctly.
Fixes: e4bd3de1be ("dnsmasq: refuse to add empty DHCP range")
Co-Authored-By: Philip Prindeville <philipp@redfish-solutions.com>
Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
allow to overwrite the detected system capabilities e.g. if devices
does not operate as bridge.
Signed-off-by: Sebastian Pflieger <sebastian@pflieger.email>
The patch refresh accidentally moved the hostapd_ucode_free_iface call to
the wrong function
Fixes: e9722aef9e ("hostapd: fix a crash when disabling an interface during channel list update")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The PKG_CPE_ID links to NIST CPE version 2.2.
Assign PKG_CPE_ID to all remaining package which have a CPE ID.
Not every package has CPE id.
Related: https://github.com/openwrt/packages/issues/8534
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
When STA is disconnected, ensure that the interface is in a cleanly stopped
state:
- if in regular enable/disable state, stop beacons if necessary
- in any other state, disable the interface
When the STA is up, ignore repeated start commands for the same channel, in
order to avoid unnecessary AP restarts
Signed-off-by: Felix Fietkau <nbd@nbd.name>
8e6485a1bcb0 PEAP client: Update Phase 2 authentication requirements
de9a11f4dde9 TTLS client: Support phase2_auth=2
b2a1e7fe7ab9 tests: PEAP and TTLS phase2_auth behavior
518ae8c7cca8 P2P: Do not print control characters in debug
a4c133ea73c7 WPS: Optimize attribute parsing workaround
7a37a94eaa0d Check whether element parsing has failed
f80d83368818 ACS: Remove invalid debug print
fb2b7858a728 FILS: Fix HE MCS field initialization
50ee26fc7044 P2P: Check p2p_channel_select() return value
a50d1ea6a2b3 Add QCA vendor attributes for user defined power save parameters
4636476b7f22 Set RRM used config if the (Re)Association Request frame has RRM IE
e53d44ac63e8 AP MLD: Use STA assoc link address in external auth status to the driver
99a96b2f9df7 AP MLD: OWE when SME is offloaded to the driver
96deacf5d710 nl80211: Skip STA MLO link channel switch handling in AP mode
d320692d918a AP MLD: Handle new STA event when using SME offload to the driver
faee8b99e928 tests: Fix eht_mld_sae_legacy_client to restore sae_pwe
c3f465c56c94 wlantest: Handle variable length MIC field in EAPOL-Key with OWE
605034240e0c wlantest: Support multiple input files
053bd8af8ed2 Recognize FTE MLO subelements
43b5f11d969a Defragmentation of FTE
3973300b8ded FTE protected element check for MLO Reassociation Response frame
74e4a0a6f1e4 wlantest: Learn AP MLD MAC address from Beacon frames
a5a0b2cf7b1b wlantest: Find non-AP MLD only from affiliated BSSs of the AP MLD
74472758584d wlantest: Recognize non-AP MLD based on any link address for decryption
1ffabd697c67 wlantest: Learn non-AP MLD MAC address from (Re)Association Request frames
4e8e515f92b9 wlantest: Use MLO search for the STA in reassociation
49bf9f2df95a wlantest: Use the MLD MAC address as well for matching STA entries
5434a42ec69c wlantest: Search for FT Target AP using MLD MAC address as well
a19fcf685cae wlantest: Include the MLD MAC address of the AP MLD in new-STA prints
709d46da73da wlantest: Do not claim update to AP MD MAC address if no change
770760454f9e wlantest: Do not update BSS entries for other AP MLDs in PTK cloning
084745ffc508 Add QCA vendor attributes for NDP setup
bf9cbb462fd9 Fix writing of BIGTK in FT protocol
011775af9443 tests: Check for beacon loss when using beacon protection
8f148d51322f Fix a compiler warning on prototype mismatch
b7db495ad9c9 AP: Fix ieee802_1x_ml_set_sta_authorized()
232667eafe0d Fix CCMP test vector issues
30771e6e05ed Include PTID in PV1 nonce construction for CCMP test vector
34841cfd9aba Minor formatting changes to CCMP test vectors
a685d84139e6 BSS coloring: Fix CCA with multiple BSS
bc0636841a70 wpa_supplicant: Fix configuration parsing error for tx_queue_*
2763d1d97e66 hostapd: Fix AID assignment in multiple BSSID
763a19286e2f AP: Add configuration option to specify the desired MLD address
bd209633eb10 AP: Use is_zero_ether_addr() to check if BSSID is NULL
bc0268d053b4 wlantest: Guess SAE/OWE group from EAPOL-Key length mismatch
a94ba5322803 EHT: Support puncturing for 320 MHz channel bandwidth
7e1f5c44c97e EHT: 320 MHz DFS support
6f293b32112a QCA vendor attributes for updating roaming AP BSSID info
5856373554eb Extend QCA vendor command to include more parameters for netdev events
e080930aa0a5 Define QCA vendor roam control RSSI attributes
fe72afe713ad Define QCA vendor attribute for high RSSI roam trigger threshold
47a65ccbfde2 P2P: Clean wpa_s->last_ssid when removing a temporary group network
884125ab7d21 tests: P2P autonomous GO and clearing of networking information
7637d0f25053 P2P: Do not filter pref_freq_list if the driver does not provide one
dd1330b502ff Fix hostapd interface cleanup with multiple interfaces
0a6842d5030e nl80211: Fix beacon rate configuration for legacy rates 36, 48, 54 Mbps
d606efe054d5 tests: Beacon rate configuration for 54 Mbps
f91d10c0e6aa tests: Update RSA 3k certificates
07d3c1177bbb tests: Make sae_proto_hostapd_status_* more robust
1085e3bdc6f6 Update iface->current_mode when fetching new hw_features
338a78846b44 Add a QCA vendor sub command for transmit latency statistics
9318db7c38bc wlantest: Use local variables for AA/SPA in FT Request/Response processing
628b9f10223d wlantest: Derive PMK-R1 and PTK using AA/SPA for MLO FT over-the-DS
104aa291e5c8 wlantest: Fix FT over-the-DS decryption
37c87efecfe3 wlantest: Search SPA using MLO aware find for FT Request/Response frame
19f33d7929e8 wlantest: Learn the Link ID for AP MLD affiliated BSSs
6ae43bb10323 wlantest: Learn link address for assoc link from (Re)Association Request
4c079dcc64da Increment hmac_sha*_vector() maximum num_elem value to 25
e6f64a8e1daf FT: FTE MIC calculation for MLO Reassociation Request frame
a83575df5994 wlantest: FTE MIC calculation for MLO Reassociation Request frames
ff02f734baf8 wlantest: Allow specific link BSS to be found with bss_find_mld()
7381c60db8f0 FT: Make FTE MIC calculation more flexible
ac9bf1cc2a4c Decrement hmac_sha*_vector() maximum num_elem value to 11
aa08d9d76803 Fix use of defragmented FTE information
78b153f90a74 Calculate defragmented FTE length during IE parsing
8cf919ffd5c4 wlantest: FTE MIC calculation for MLO Reassociation Response frame
d12a3dce82a9 wlantest: Store and check SNonce/ANonce for FT Authentication
20febfd7838d wlantest: Dump MLO association information in debug
609864d6a8a1 Add QCA vendor attribute to configure MLD ID in ML probe request
12154861e24a Add support for conversion to little endian for 24 bits
c437665041c0 Add Non EHT SCS Capability in (Re)Association Request frames
33da386553b7 SCS: Add support for QoS Characteristics in SCS request
edfca280cbe8 SCS: Add support for optional QoS Charateristics parameters
32dcec9529ec Send actual MFP configuration when driver takes care of BSS selection
123d16d860fa Update hw_mode when CSA finishes
b3d852560bda Change QCA vendor configure attribution name of peer MAC address
12fabc4765c2 Add QCA vendor attribute for configuring max A-MPDU aggregation count
f6eaa7b729cb Add QCA vendor attribute for TTLM negotiation support type
f6dcd326fea7 wlantest: Indicate ToDS/FromDS values for BSS DATA entries
6ce745bb87d4 wlantest: MLO support for decrypting 4-address frames
850dc1482953 wlantest: Remove duplicated A1/A2/A3 override detection for MLO
770e5a808fbb wlantest: Determine whether A1 points to STA once in rx_data_bss_prot()
377d617b574a Define new BSS command info mask for AP MLD address
d3ab6e001f62 wlantest: Use non-AP MLD's MLD MAC address in FT over-the-air derivation
a845601ffe32 wlantest: Derive PTK in MLO using MLD MAC addresses for FT over-the-air
0cd2bfc8a402 wlantest: Fix FTE MIC calculation for MLO Reassociation Response frames
528abdeb673b wlantest: Learn group keys from MLO FT Reassociation Response frames
990600753dd9 wlantest: Defragment Basic MLE before processing
de043ec01ab5 wlantest: Defragment the Per-STA Profile subelement
bae1ec693c44 wlantest: Minimal parsing of Basic MLE STA Profile
ba1579f3bf7c Clear BIGTK values from wpa_supplicant state machine when not needed
b46c4b9a916a tests: Beacon protection and reconnection
3e71516936b7 Document per-ESS MAC address (mac_addr=3 and mac_value)
f85b2b2dee3b Extend wpa_parse_kde_ies() to include EHT capabilities
e3a68081bc1e driver: Add option for link ID to be specified for send_tdls_mgmt()
c7561502f2e8 nl80211: Use a QCA vendor command to set the link for TDLS Discovery Response
a41c8dbdd84e TDLS: Copy peer's EHT capabilities
626501434be1 TDLS: Learn MLD link ID from TDLS Discovery Response
5f30f62eead7 TDLS: Reply to Discovery Request on the link with matching BSSID
940ef9a05c0f TDLS: Use link-specific BSSID instead of sm->bssid for MLO cases
f429064189c3 TDLS: Set EHT/MLO information for TDLS STA into the driver
dd25885a9daa Remove space-before-tab in QCA vendor related definitions
af6e0306b2a9 Fix typos in QCA vendor related definitions
4c9af238c1e4 Fix inconsistent whitespace use in QCA vendor related definitions
e5ccbfc69ecf Split long comment lines in QCA vendor related definitions
Signed-off-by: Felix Fietkau <nbd@nbd.name>
MAC address and interface name assigned by mac80211.sh depend on the order in
which interfaces are brought up. This order changes when interfaces get added
or removed, which can cause unnecessary reload churn.
One part of the fix it making MAC address allocation more dynamic in both
wpa_supplicant and hostapd, by ignoring the provided MAC address using
the next available one, whenever the config does not explicitly specify one.
The other part is making use of support for renaming netdevs at runtime and
preserving the MAC address for renamed netdevs.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
set_config causes the ucode bss resource to be re-created and because of that
the bss list needs to be updated as well
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When switching from a STA-only configuration to AP+STA on the same phy, the
STA was previously restarted in order to notify hostapd of the new frequency,
which might not match the AP configuration.
Fix the STA restart by querying the operating frequency from within hostapd
when bringing up the AP.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
f429bd94f99e system-linux: switch to new ETHTOOL_xLINKSETTINGS API
Fixes AN announcement for speeds beyond 1 GBit/s.
Adds new UCI options for Ethernet devices:
- autoneg: switch on or off auto-negotiation
- pause: if set to 0, do not announce symmetric flow control capability
- asym_pause: if set to 0, do not announce asymmetric flow control
capability.
- rxpause: if set overrides AN and forces RX pause accordingly
- txpause: if set overrides AN and forces TX pause accordingly
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
db3934d2f740 scripts/netifd-wireless.sh: properly fix WPA3 Enterprise support
Support the following values for the different WPA3 Enterprise modes:
- wpa3-mixed: WPA3 Enterprise transitional mode
This supports EAP with both SHA1 and SHA-256, with optional MFP
- wpa3: WPA3 Enterprise only mode
This supports only SHA256 with mandatory MFP
- wpa3-192: WPA3 Enterprise with mandatory 192 bit support
This uses only GCMP-256 ciphers
Disable 192 bit support and GCMP-256 ciphers for the regular "wpa3" mode.
It seems that even leaving in optional 192 bit support breaks auth on some
clients, including iOS devices.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
WPA3 Enterprise-transitional requires optional MFP support and SHA1+SHA256
WPA3 Enterprise-only requires SHA1 support disabled and mandatory MFP.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
It seems that this was not functioning properly and was likely completely unused.
Keeping this out of tree also introduced some annoying churn when updating, because
of the iw nl80211.h sync patch.
If this is needed, it will be reintroduced when/if it is added upstream
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When the STA is brought up, it is set to DISABLED before adding the bss to ucode,
so the first trigger to disable the AP is missed.
Reported-by: Michael-cy Lee (李峻宇) <Michael-cy.Lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Commit e978072baaca ("Do prune_association only after the STA is
authorized") causes issues when an STA roams from one interface to
another interface on the same PHY. The mt7915 driver is not able to
handle this properly. While the commits fixes a DoS, there are other
devices and drivers with the same limitation, so revert to the orginal
behavior for now, until we have a better solution in place.
Fixes: #13156
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
It cannot be properly cloned, since it is attached to the resource type.
Use a separate registry for data. Fixes object confusion issues
Signed-off-by: Felix Fietkau <nbd@nbd.name>
An active client mode interface could prevent the AP from claiming its channel
and mess up the bringup sequence order
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Drop obsolete control interface patches.
This fixes some corner cases in the previous code where the segment 0 center
frequency was not adjusted properly, leading to logspam and non-working AP
interfaces.
Additionally, shutting down the AP was broken, because the next beacon update
would re-enable it, leading to a race condition on assoc.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fixes this error: hostapd: nl80211: kernel reports: integer out of range
Reported-by: Hartmut Birr <e9hack@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Check the phy before removing unrelated netdevs on the same hw device
Reported-by: Hartmut Birr <e9hack@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When building xdp-tools with CONFIG_USE_LLVM_HOST=y, on a host that
enabled stack protector by default in Clang, compilation fails with the
following error:
CLANG xdp-dispatcher.o
clang-16: error: ignoring '-fstack-protector-strong' option as it is not currently supported for target 'bpfeb' [-Werror,-Woption-ignored]
Add -fno-stack-protector to BPF_CFLAGS to fix this.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Include AP ucode source file
Fixes: e56c5f7b27 ("hostapd: add ucode support, use ucode for the main ubus object")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
8c2758b4fbbb wireless: add support for replacing data blobs at runtime
0ff22a6a68ce wireless: enable dynamic reconfiguration by default
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This implements vastly improved dynamic configuration reload support.
It can handle configuration changes on individual wifi interfaces, as well
as adding/removing interfaces.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This can be used to run a standalone EAP server that can be used from
other APs. It uses json as user database format and can automatically
handle reload.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
At least Fedora and RHEL 9 set RSAMinSize=2048, so when trying to use
failsafe, we get 'Bad server host key: Invalid key length'
To workaround the issue, we can use: ssh -o RSAMinSize=1024 ...
Generating 2048 bits RSA is extremely slow, so add ed25519.
We keep RSA 1024 to be as compatible as possible.
Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com>
ChangeLog:
125b080 Release version 6.4.
5660918 update UAPI header copies
f493e63 netlink: fix duplex setting
b3e341c cmis: report LOL / LOS / Tx Fault
045d8db sff-8636: report LOL / LOS / Tx Fault
a6505f3 drop checks for macros provided in UAPI header copies
86c0c41 do not check for strtol() function
dd8e3ae actually check for C11 compiler
43e4d30 add local copies of macros from autoconf-archive
faa4700 drop check for big endian types
31b7b5e Require a compiler with support for C11 features
946d18b update UAPI header copies
eebf01f ethtool: Add support for configuring tx-push-buf-len
2782ea8 update UAPI header copies
Signed-off-by: Nick Hainke <vincent@systemli.org>
d1f07cf devices: add device id for Atheros AR9287 and AR9380
65ea345 nl80211: constify a few arrays
ca79f64 lib: report byte counters as 64 bit values
This contains an ABI change, increase the ABI version too.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
493e1589bc8b bridge: fix coverity false positive report
03a619947717 bridge: add support for configuring extra vlans for the bridge itself
4bea6d21a9ab wireless: fix changing reconf/serialize options in configuration
255b4d5c472e wireless: fix handling config reload with reconf=1
1ab992a74b43 wireless: fix another reconf issue
Signed-off-by: Felix Fietkau <nbd@nbd.name>
5211264 odhcpd: add support for dhcpv6_pd_min_len parameter
c6bff6f router: Add PREF64 (RFC 8781) support
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
1571e18e4a69 bridge: add support for configuring extra tagged vlans on member devices
b719f189f243 bridge: make hotplug-added vlans default to tagged
edf3aced9f9a bridge: add support for adding vlan ranges via hotplug
Signed-off-by: Felix Fietkau <nbd@nbd.name>
