Add new functions for ath11k caldata:
- ath11k_patch_mac (from 0 to 5)
- ath11k_remove_regdomain
- ath11k_set_macflag (some pre-caldata have the nvMacFlag flag unset which is needed to change the MAC address)
Additionaly for ath10k caldata:
- ath10k_remove_regdomain
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
This update contains a minor fix to resolve "detected write beyond size
of field" warning during compilation:
* "replace [0] with []" (1d0d08c)
All patches still apply.
References:
* https://github.com/openwrt/openwrt/issues/15108
Signed-off-by: Stefan Kalscheuer <stefan@stklcode.de>
Spectrum SAX1V1K is a AX WIFI router with 3 1G and 1 2.5G ports.
The router is provided to Spectrum customers.
It is OEM of Askey RT5010W
https://forum.openwrt.org/t/spectrum-sax1v1k-askey-rt5010w-openwrt-support/149923
It continues the original work by @MeisterLone to get this device supported.
Specifications:
```
• CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz
• RAM: 2048MB of DDR3
• Storage: 1024MB eMMC
• Ethernet: 3x 1G RJ45 ports (QCA8075) + 1 2.5G Port (QCA8081)
• WLAN:
• 2.4GHz: Qualcomm QCN5024 4x4 802.11b/g/n/ax 1174 Mbps PHY rate
• 5GHz: Qualcomm QCN5054 4x4 802.11a/b/g/n/ac/ax 2402 PHY rate
• LED: 1 gpio-controlled dual color led (blue/red)
• Buttons: 1x reset
• Power: 12V DC jack
```
Notes:
```
• This commit adds only single partition support, that means
sysupgrade is upgrading the current rootfs partition.
• Installation can be done by serial connection only.
• A poulated serial header is onboard
https://forum.openwrt.org/t/spectrum-sax1v1k-askey-rt5010w-openwrt-support/149923/6
• RX/TX is working, u-boot bootwait is active, secure boot is enabled.
```
Installation Instructions:
**Most part of the installation is performed from an initramfs image.**
Boot initramfs : Using serial connection
1. Boot up the device and wait till it displays "VERIFY_IB: Success. verify IB ok"
2. Once that message appears,
login with username 'root'
password serial number of your router in uppercase.
3. Use vi to paste the 'open.sh' script from @MeisterLone github on your device
https://github.com/MeisterLone/Askey-RT5010W-D187-REV6/blob/master/Patch/open.sh
4. chmod 755 open.sh
5. ./open.sh
6. Set your ip to 192.168.0.1
7. Run a TFTP server and host the initramfs image on the TFTP server and name it "recovery.img"
8. Reboot device. On boot it will try TFTP.
Install OpenWrt from initramfs image:
1. Use SCP (or other way) to transfer OpenWrt factory image
2. Connect to device using SSH (on a LAN port)
3. Flash firmware: sysupgrade
# sysupgrade -n -v /tmp/openwrt_sysupgrade.bin
4. Set U-boot env variable: bootcmd
# fw_setenv bootcmd "run fix_uboot; run setup_and_boot"
5. Reboot the device
# reboot
6. Once device is booted, residue of previous firmware will prevent openwrt to work properly.
Factory Reset is MUST required
# Once serial console is displaying to login, hold reset button for 10 sec
7. Now everything should be operational.
Note: this PR adds only single partition support, that means sysupgrade is
upgrading the current rootfs partition
Signed-off-by: Connor Yoon <j_connor@taliaent.com>
ec8c620fd5f4 split bridge-local disable into rx and tx
40b1c5b6be4e flow: do not attempt to offload bridge-local flows
Signed-off-by: Felix Fietkau <nbd@nbd.name>
For interface type parameters, the man page documents patterns:
```
*,!eth*,!!eth1
uses all interfaces, except interfaces starting with "eth",
but including "eth1".
```
* Renamed `_ifname` to `_l2dev`.
* get the l2dev via network_get_physdev (and not l3dev)
* Glob pattern `*` is also valid - use noglob for this
The net result is that now interface 'names' including globs '*' and '!'
inversions are included in the generated lldpd configs.
Temporarily `set -o noglob` and then `set +o noglob` to disable & enable
globbing respectively, because when we pass `*` as an interface choice,
other file and pathnames get sucked in from where the init script runs,
and the `*` never makes it to lldpd.
Tested extensively on: 22.03.6, 23.05.3
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
[ squash with commit bumping release version ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Lets update to 2024.04 in order to drop all of the patches as they have
been merged upstream.
Tested on Methode eDPU.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
f9a28a9ce864 ustream-ssl: poll connection on incomplete reads
3c49e70c4622 ustream-ssl: increase number of read buffers
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Reduce calls and pipes and read from urandom once directly with hexdump
for the necessary 5 bytes of random data to build the 48 bit ULA Prefix.
Fewer calls and forks; finish quicker; less memory used.
Tested on: 23.05.3
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
It seems that move to kernel 6.6 somehow fixed the remoteproc restart so
now it properly restarts and thus coldboot calibration works as well.
ipq60xx still seems to be broken in a different way so keep it disabled.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add patch fixing rmmod and insmod. Lots of flawed logic fixed that
permits the module to correctly rmmod and insmod later.
Just to quote some change, use phy_detach instead of phy_disconnect, fix
exclusive reset_control that could only be used once, fix kernel panic
on second edma_cleanup, stop traffic before module exit...
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This reverts commit a9e22ffa50.
After doing a clean rebuild, it turns out that this change is not necessary
Signed-off-by: Felix Fietkau <nbd@nbd.name>
3159bbe0a2eb improve isolation when selecting a fixed output port
c77a7a1ff74d nl: fix getting flow offload stats
a08e51e679dd add support for disabling bridge-local flows via config
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The new script uses a different strategy compared to the previous one.
Instead of trying to split flows by hash and spread them to all CPUs,
use RPS to redirect packets to a single core only.
Try to spread NAPI thread and RPS target CPUs across available CPUs
and try to ensure that the NAPI thread is on a different CPU than the
RPS target. This significantly reduces cycles wasted on the scheduler.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Limiting allowed channels per device may be required and is commonly
supported on other drivers, so include a pending patch to add support for
the same.
Signed-off-by: Robert Marko <robimarko@gmail.com>
As commit 3ce1e4c3d3 ("d1: define subtarget specifically") added the
'generic' subtarget, without 'BUILD_SUBTARGET' the correspond U-Boot
package will be no longer selected automatically.
Fixes: 3ce1e4c3d3 ("d1: define subtarget specifically")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Update to the latest upstream release to include recent improvements and
bugfixes. Update copyright, fix typo in PKG_NAME, and remove unneeded use
of MAKE_VARS definition in Makefile. Drop 001-cflags.patch and simplify
002-includes.patch after refreshing. Also simplify LTO/DCE build flags.
Link: https://github.com/libbpf/bpftool/releases/tag/v7.4.0
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Update to the latest upstream release to include recent improvements and
bugfixes, and update copyright. Remove MAKE_VARS usage in Makefile and drop
001-cflags.patch which are no longer needed. Also add flags to disable LTO,
mistakenly dropped earlier.
Link: https://github.com/libbpf/libbpf/releases/tag/v1.4.0
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
only available from >= 1.0.15
Comments are useful. Apparently this config parameter was committed when
openwrt used an older version of lldpd which did not yet support it.
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
Starting with Linux 6.3 the .probe call no longer got the id parameter,
see also commit torvalds/linux@03c835f498
("i2c: Switch .probe() to not take an id parameter").
As the parameter is anyway unused by the driver, drop it when
building the GCA230718 LED driver for newer kernels.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
HW specifications:
* Mediatek MT7981A
* 256MB SPI-NAND
* 512MB DRAM
* Uplink: 1 x 10/100/1000Base-T Ethernet, Auto MDIX, RJ-45 with 802.3at
PoE (Built-in GBe PHY)
* LAN: 1 x 10/100/1000Base-T Ethernet, Auto MDIX, RJ-45 (Airoha EN8801SC)
* 1 Tricolor LED
* Reset button
* 12V/2.0A DC input
Installation:
Board comes with OpenWifi/TIP which is OpenWrt based, so sysupgrade can
be used directly over SSH.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
This module supports the Microchip Technology Inc (SMSC)
EMC2301/EMC2302/EMC2303/EMC2305 fan speed PWM controller chips.
Signed-off-by: Oleg S <remittor@gmail.com>
Historically it's possible to leave the `SUBTARGETS` undefined and
automatically fallback to a "generic" subtarget. This however breaks
various downstream scripts which may have expectations around filenames:
While some targets with an explicit generic subtarget contain `generic`
in the filenames of artifacts, implicit "subtargets" don't.
Right now this breaks the CI[1], possibly also scripts using the ImageBuilders.
This commit removes all code that support implicit handling of
subtargets and instead requires every target to define "SUBTARGETS".
[1]: https://github.com/openwrt/openwrt/actions/runs/8592821105/job/23548273630
Signed-off-by: Paul Spooren <mail@aparcar.org>
e209a4ced1d8 add strdupa macro for compatibility
af1962b9a609 uclient: add helper function for getting ustream-ssl context/ops
488f1d52cfd2 http: add helper function for checking redirect status
b6e5548a3ecc uclient: defer read notifications to uloop timer
352fb3eeb408 http: call ustream_poll if not enough read data is available
e611e6d0ff0b add ucode binding
ddb18d265757 uclient: add function for getting the amount of pending read/write data
980220ad1762 ucode: fix a few ucode binding issues
6c16331e4bf5 ucode: add support for using a prototype for cb, pass it to callbacks
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is mostly a cosmetic cleanup. The absence of
the return statement was not causing any problems.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
