The ZBT-WG826 is available with 16 or 32 MByte of flash. Split the
device tree source file, rename the currently supported 16 MByte
version and add the 32 MByte variant.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The Digineo AC1200 Pro is the 32MB flash variant of the ZBT-WG3526 with
unpopulated/exposed sdhci slot. Rename to board to the OEM/ODM name and
add the sdhci kernel module to use it for multiple clones.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The ZBT-WG3526 is available with 16 or 32 MByte of flash. Rename the
current supported 16MByte version to indicate which flash size variant
is supported.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use fixed led names and add each board variant instead of manipulating
the board name.
It makes the ramips board name function less different to the one used
in other targets and allows to merge them with a common function.
Signed-off-by: Mathias Kresin <dev@kresin.me>
PSG1218 got only 4 Ethernet ports and WAN on port 3 while
PSG1218K2C got 5 Ethernet ports and WAN on port 4
Switch to use kmod-kt76x2 instead of kmod-mt76 for both devices while
at it.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This patch adds support for the Zbtlink ZBT-WE2026.
Specification:
- SoC: MediaTek MT7620N (580MHz)
- RAM: 64 MiB
- Flash: 8 MiB SPI
- LAN: 4x100M
- WAN: 1x100M
Installation through bootloader webserver:
- With the power unplugged press and hold reset button.
- Plug power and hold reset button until LED starts to blink.
- Install sysupgrade image using web interface on 192.168.1.1.
Signed-off-by: Vaclav Svoboda <svoboda@neng.cz>
Specifications:
* SoC: MT7620A
* RAM: 64 MB DDR
* Flash: 8MB NOR SPI flash
* WiFi: MT7612E (5Ghz) and builtin MT7620A (2.4GHz)
* LAN: 1x100M
The -factory images can be flashed from the device's web
interface or via nmrpflash.
Co-authored-by: Paul Oranje <por@xs4all.nl>
Signed-off-by: Paul Oranje <por@xs4all.nl>
Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
This patch adds support for the Netgear R6220, aka Netgear AC1200 and
R6220-100NAS.
Specification:
- SoC: MediaTek MT7621ST (880 MHz)
- Falsh: 128 MiB (Macronix MX30LF1G08AA-TI)
- RAM: 128 MiB (Nanya NT5CB64M16FP-DH)
- Wireless: MediaTek MT7603EN b/g/n , MediaTek MT7612EN an+ac
- LAN speed: 10/100/1000
- LAN ports: 4
- WAN speed: 10/100/1000
- WAN ports: 1
- Serial baud rate of Bootloader and factory firmware: 57600
Installation through telnet:
- Copy kernel.bin and rootfs.bin to a USB flash disk, plug to usb port
on the router.
- Enable telnet with link: http://192.168.1.1/setup.cgi?todo=debug
(login if required, default: admin password)
- You will see "Debug Enabled!"
- Telnet 192.168.1.1 and login with "root"
- ls /mnt/shares/ to find out path of your USB disk. 'myUdisk' for
example.
- cd /mnt/shares/myUdisk
- mtd_write write rootfs.bin Rootfs
- mtd_write write kernel.bin Kernel
- reboot
nmrpflash can be used to recover to the netgear firmware if a broken
image was flashed.
Signed-off-by: Hanqing Wong <hquu@outlook.com>
This device features both a 2.4 and 5Ghz radio, and supports
802.11a/b/g/n/ac modes.
It has 5 Gb-Ethernet ports and a USB 3.0 host port.
It is powered by the Mediatek MT7621 SoC, and the MT7602E and MT7612E wifi
chipsets, together with 128MB of RAM and 16 MB of SPI Flash.
The stock firmware is in fact based on some openwrt barrier breaker, with a
mediatek SDK kernel, and an afoundry custom made web interface (not LuCI
based).
Firmware update page on the stock web interface can not accept sysupgrade
images, it bricks the device.
At this point, the only working solution I found was to connect to the
serial console port (available on J4 header) and to use opkg to install
dropbear.
Then scp the sysupgrade file in the device's /tmp and run sysupgrade from
console without preserving configuration files.
Signed-off-by: Francois Goudal <francois@goudal.net>
This patch adds supports for the HiWiFi HC5962(gee4) http://www.hiwifi.com
Short specification:
- MT7621AT + MT7612EN + 7603EN
- 256MB DDR3 RAM
- 128MB NAND flash
- 1+3 x 1000M Ethernet
- 1x USB 2.0 port. 1x USB 3.0 port.
- reset button
- UART pad on PCB (JP3: TX, RX, GND, 3.3V)
Flash instruction:
1, Download lede-ramips-mt7621-hc5962-squashfs-factory.bin
2, Login as root via SSH on 192.168.199.1 and then copy factory.bin(using wget or nc or...) to /tmp/
3, use the following commands:
$ mtd write /tmp/lede-ramips-mt7621-hc5962-squashfs-factory.bin firmware
$ mtd erase firmware_backup && reboot
After reboot you should be able to login as root via SSH on 192.168.1.1
Signed-off-by: ZengFei Zhang <zhangzengfei@kunteng.org>
HC5661A is almost the same as HC5661 but MT7628AN is used instead of MT7620A.
- MT7628AN
- 128 MiB DDR2 RAM (W971GG6KB-25)
- 16 MiB SPI NOR flash (W25Q128)
- SD slot (not work yet)
- 1+4 x 100M Ethernet
- 802.11 b/g/n Wi-Fi
- 3 x LED
- 1 x button
- UART pad on PCB (JP1: TX, RX, GND, 3.3V)
The factory flash layout seems different from HC5661.
"hwf_config" is renamed to "oem" and its size changes to 0x20000.
It is modified accordingly in the dts file.
0x000000000000-0x000000030000 : "u-boot"
0x000000030000-0x000000040000 : "hw_panic"
0x000000040000-0x000000050000 : "Factory"
0x000000050000-0x000000160000 : "kernel"
0x000000160000-0x000000fc0000 : "rootfs"
0x000000bb0000-0x000000fc0000 : "rootfs_data"
0x000000fc0000-0x000000fe0000 : "oem"
0x000000fe0000-0x000000ff0000 : "bdinfo"
0x000000ff0000-0x000001000000 : "backup"
0x000000050000-0x000000fc0000 : "firmware"
To install LEDE, enabled the "developer mode",
which will *void your warranty* and open the SSH server at port 1022.
sysupgrade -n -F lede-ramips-mt7628-hc5661a-squashfs-sysupgrade.bin
SD slot:
- Tried to add modules kmod-sdhci kmod-sdhci-mt7620, and corresponding dts block.
- It will block WAN + 3xLAN ports, only one LAN works.
- I'm not sure why, everything else works fine.
Signed-off-by: Wang JiaWei <buaawjw@gmail.com>
The Sanlinking Technologies D240
(http://www.sanlinking.com/en/29-dual-4g-wifi-router.html) is basically the same
device as the ZBT WE826, so adding support for it in LEDE is straight forward.
The differences is that the D240 has two mini-PCIe slots (instead of one), blue
LEDs and supports PoE.
Specification:
* CPU: MT7620A
* 1x 10/100Mbps POE (802.3af/802.3at) Ethernet, 4x 10/100Mbps.
* 16 MB Flash.
* 128 MB RAM.
* 1x USB 2.0 port.
* 2x mini-PCIe slots.
* 2x SIM slots.
* 1x 2.4Ghz WIFI.
* 1x button.
Wifi, USB, switch and both mini-PCIe slots are working. I have not been able to
test the SD card reader.
The device comes pre-installed with an older version of OpenWRT, including Luci.
In order to install LEDE, you need to follow the existing procedure for updating
OpenWRT/LEDE using Luci. I.e., you need to access the UI and update the firmware
using the sysupgrade-image. Remember to select that you do not want to keep
existing settings. The default router address is 192.168.10.1 and
username/password admin/root (at least on my devices).
If you brick the device, the procedure for recovery is the same as for the
WE826. Please see the wiki page for that device for instructions.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Buffalo WCR-1166DS is a small wireless router with
- MT7628AN + MT7612E
- 64MiB DDR2 SDRAM
- 16MiB SPI flash
- 2T2R 11ac/a/b/g/n Wi-Fi
- 2x 10/100M ethernet switch
- 8x programmable LED
- 3x button
- UART pad on PCB (J2: 3.3V, GND, TX, RX)
factory image can be installed via stock web UI.
due to the "dual image" function in the bootloader, the second half of
the SPI flash ("firmware2" partition) cannot be used as a part of the
file system.
Signed-off-by: FUKAUMI Naoki <naobsd@gmail.com>
This patch adds support for the Netgear WN3000RPv3
http://www.netgear.com/support/product/wn3000rpv3.aspx
Specifications:
- SoC: MediaTek MT7620A (580MHz, ramips)
- RAM: 32MB DDR
- Storage: 8MB NOR SPI flash
- Wireless: builtin MT7620A, 2x2:2 with u.FL connectors
- Ethernet: 1x100M
- Serial: JP1 header, 57600-8N1
- Stock firmware based on OpenWRT Kamikaze
Like the EX2700, the bootloader expects a secondary image signature,
see https://forum.openwrt.org/viewtopic.php?pid=312577#p312577
This is why the same fakeroot image is used for the WN3000
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
This patch adds support for the Onion Omega2 and Omega2+ (https://onion.io)
Specifications:
- SoC: MediaTek MT7688AN (580MHz, ramips)
- Omega2
- RAM: 64MB DDR
- Storage: 16MB NOR SPI flash onboard
- Omega2+
- RAM: 128MB DDR
- Storage: 32MB NOR SPI flash onboard + microSD slot
- Wireless: Built into MT7688AN (mt76) with onboard 1x chip antenna and u.FL connecter
- Ethernet: 1x100M pins on Omega2 & Omega2+, can use Ethernet Expansion and an Omega Dock to get a physical Ethernet port
- Strongly recommend using the Omega2 & Omega2+ with a Dock (Expansion Dock, Power Dock, Arduino Dock 2, Mini Dock)
- All Docks Provide:
- Micro-USB port to provide power to the Omega
- On the Expansion and Mini Docks, can also access the terminal (UART0) via serial
- USB 2.0 socket connected to Omega
- Just the Expansion Dock, Power Dock, and Arduino Dock 2 provide:
- Omega GPIO breakout
- Allows for connection of Omega Expansions:
- Ethernet Expansion
- Relay Expansion
- PWM Expansion
- OLED Expansion
- Ethernet Expansion
- Proto Expansion
- Cellular Expansion
Signed-off-by: Lazar Demin <lazar@onion.io>
This patch adds support for the VoCore VoCore2 and its complementary
"ultimate" dock.
Specifications:
- SoC: MediaTek MT7628AN (580MHz, ramips)
- RAM: 128MB DDR2 166MHz
- Storage: 16MB NOR SPI flash onboard + microSD slot on dock
- Wireless: Built into MT7628AN (mt76) with 1T1R firmware on VoCore2
boards with onboard 1x chip antenna
- Ethernet: 1x100M (port0) on dock, 1x100M (port2) on PCB header
- Dock hardware:
- USB 2.0 socket
- MicroSD socket
- 100Mbps Ethernet x1
- 3.5mm headphone jack (TRRS) connected to Everest Semi ES8388 I2S
DAC/ADC (support WIP)
- Micro USB for power and console (UART2)
Initial installation:
- VoCore2 comes preinstalled with a fork of OpenWrt CC and AP on
SSID "VoCore2"
- Connect to VoCore2 by Ethernet or Wi-Fi
- `ssh root@192.168.1.1` (password is "vocore")
- scp/wget/etc. LEDE sysupgrade.bin to VoCore2
- `sysupgrade -n <your image>.bin` (don't keep old config, as the
original firmware uses Ralink SDK Wi-Fi drivers and not
mt76+mac80211)
- after sysupgrade completes, Wi-Fi will be disabled by default so use
Ethernet or the micro USB console to configure Wi-Fi again
Signed-off-by: Andrew Yong <me@ndoo.sg>
Use the the dt-bindings macros and add the reset button.
Set the correct polarity for the LEDs and drop the default state.
Remove all trigger for the LEDs. According to the manual the LEDs are
only used to show the operation state, where blue means normal
operation.
Use the MAC-Addresses stored in EEPROM for the ethernet and the
wireless interface.
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
[use leds only for boot status indication, add proper commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
This fixes the partition name for the firmware splitter, the cfi
address and adds the mtd-eeprom address for wmac. It adds additional
LEDs and make use of them in diag.sh and 01_leds.
Please note that the ":blue:wired" LED is used because the
":blue:router" behaviour is unpredictable for failsafe indication. The
issue with the router LED is that you have two states only.
"off" is steady on and "on" blinks. Therefore the wired LED is more
suitable.
Furthermore it reuses the correct switch configuration definition to
reflect the device ports and numbering. Additionally fixes the issue
that the default configuration is not applied as no port 6 exists on
this device.
Signed-off-by: Tobias Wolf <github-NTEO@vplace.de>
use pwr LED in diag.sh
Expose unused pinmux pins as GPIOs
export power LED and buzzer pins
Use rb750gr3:blue:pwr LED in diag.sh for boot status instead of rb750gr3:green:usr
Signed-off-by: Andrew Yong <me@ndoo.sg>
The Dlink DWR-512-B modem is a ralink 5350 processor based embedding
a 3G mini-pcie router.
The oem JBOOT bootloader has to be replaced by a RT5350 SDK
U-Boot such as https://github.com/stevenylai/ralink_sdk - U-Boot
configured for the RT5350 256MiB SDR.
Main reason to change the bootloader is the encrypted header used to
store the kernel image. In this way an image can only be generated
using the propietary binboy tool (included in the GPL distribution
from Dlink). The binboy tool doesn't allow to modify the kernel/rootfs
partition scheme. This is considered a big constraint (limited kernel
size and inefficient usage of flash space).
For interested people I pubblished the details of my investigation
about the encrypted firmware header here:
http://lists.infradead.org/pipermail/lede-dev/2016-October/003435.html
Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
Factory image can be installed via Zyxel WebUI.
Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com>
[removed linux,modalias parameter from flash node in dts]
[removed sdhci node from dts; no sd card slot here]
Signed-off-by: Mathias Kresin <dev@kresin.me>
The Sitecom firmware upgrade file has SENAO_FIRMWARE_TYPE 2 set. This
looks rather wrong since SENAO_FIRMWARE_TYPE 2 is kernel only but the
file is way to big for only including a kernel.
The factory image need to have the dlf file extension. Otherwise the
Sitecom firmware rejects the file.
The stock firmware uses the following mac addresses:
LAN: 00:0C:F6:AA:BB:D8 (u-boot env: ethaddr)
2,4: 00:0C:F6:AA:BB:D8 (EEPROM)
5: 00:0C:F6:AA:BB:DC (EEPROM)
WAN: 00:0C:F6:AA:C8:43 (u-boot env: wanaddr)
Assuming the mac address range :D8 to :DC is reserved for this device,
the MAC addresses were reorder to have a unique MAC address for each
interface:
2.4GHz: 00:0C:F6:AA:BB:D8
LAN: 00:0C:F6:AA:BB:D9
WAN: 00:0C:F6:AA:BB:DA
5 GHz: 00:0C:F6:AA:BB:DC
The first MAC is assigned to the 2.4GHz WiFi interface
to keep compatibility with the SSIDs printed on the case, which have
the last three sextets of the MAC address appended.
There are still issues with the rt2x00 driver. It is not possible to
use both wireless interfaces at the same time. The 2.4 GHz
wireless (PCIe) only works if the internal 5GHz wireless is/has been
enabled or used for scanning. The internal 5GHz wireless only works if
the 2.4GHz wireless (PCIe) was never enabled. Disabling the 2.4Ghz
after it was enabled will result in stations seeing the 5Ghz AP but are
unable to connect.
Due to the not optimal working wifi the manufacture, backup and storage
partitions of the OEM firmware are kept for now to allow an easy switch
back to the Sitecom firmware.
Signed-off-by: Jasper Scholte <NightNL@outlook.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
The MikroTik hEX v3 (RB750Gr3) is a MT7621AT board which is similar to most MT7621 reference designs, it can be easily supported by this patch; however, the stock RouterBOOT bootloader has to be replaced by a MT7621 SDK U-Boot such as https://github.com/ndoo/RB750Gr3-U-Boot - U-Boot configured for the RB750Gr3 (16MiB SPI flash, 256MiB DDR3 RAM at 1200MHz).
RouterBOOT, the stock bootloader, does not initialize the UART and boots silently, making it preferable to replace it with a MT7621 SDK U-Boot with UART (57600 8N1) that supports HTTP, TFTP or serial upload of sysupgrade firmware and U-Boot.
Furthermore, RouterOS, the stock firmware, is contained in a proprietary modification of SquashFS without GPL sources; UART is also disabled in stock firmware.
The combination of LEDE firmware generated by this PR and MT7621 SDK U-Boot expects the printed MAC address to reside at offset `0xe000` of the factory partition (absolute offset is `0x4e000`); this is similar to the factory MAC address offset for several other MT7621 devices.
A 16MiB flash dump suitable for use with flashrom will be provided if/once this patch is accepted and binaries are built by LEDE buildbot. Alternatively, writing the U-Boot to the SPI flash starting at 0x0 offset and booting the board with serial console attached will allow TFTP, HTTP or serial upload of sysupgrade firmware.
Signed-off-by: Andrew Yong <me@ndoo.sg>
- setting read-only flag to important partitions
- enabling PA to improve 2.4 GHz signal strength
- add missing leds
- rename colour led
- add mac adress to 5GHz wlan interface
- included <dt-bindings/input/input.h> and <dt-bindings/gpio/gpio.h>
Signed-off-by: Henryk Heisig hyniu@o2.pl
Assign the reset functionality to the wps/reset buttons. Use the wlan
switch of the 6200n to enable/disable wlan.
Add the internet led of the 6200nl and use the led for boot status
indication
Signed-off-by: Mathias Kresin <dev@kresin.me>
applied bb-final-ramips-add-zyxel-nbg-419n2.patch from
123serge123, found at https://yadi.sk/d/1ZV0lKJwbTE65;
see https://forum.openwrt.org/viewtopic.php?pid=246905#p246905,
modified slightly to fit to CC release and to new lede build
system: image/rt305x.mk include file is used now
changed NBG-419N2.dts format to fit style of other dts files
Signed-off-by: Klaus <k-laus@quantentunnel.de>
- CPU: MT7620A 580MHz
- Flash: 8MB - RAM: 64MB
- External PA+LNA on both WLAN2.4 and WLAN5
- 4x LAN ethernet and 1x WAN ethernet
Signed-off-by: Xuefu Lin <xuefulin@gmail.com>
Thunder Timecloud is a small NAS with MT7621A. It has 1 USB port and an
SD Card slot. There is no wireless cards.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
D-Link DCH-M225 is based on Mediatek MT7620 with 64MB ram, 8MB flash,
3.5mm audio out support. but no ethernet and usb ports.
so you must default enable wifi.
Signed-off-by: Michael Lee <igvtee@gmail.com>
The Widora board is similar to the Linkit 7688 but features a larger flash
capacity.
Signed-off-by: Yuan Chenmang <771992497@qq.com>
[Jo-Philipp Wich: Reword commit message, cleanup initial PR]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
add support for Planex MZK-EX750NP.
MZK-EX750NP is MT7620A and MT7610E based 11ac wifi repeater.
Built-in power supply.
64MiB RAM, 8MiB SPI Flash, non Wired Ethernet.
Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
SVN-Revision: 49268
CS-QR10 is MT7620A based IP Camera.
the camera and sound does not work with kernel 4.4.
- camera chip is sn9c291.
- sound chip is wm8960.
Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
SVN-Revision: 49234
The WG3526 is the follow-up to the 2626 and is mostly the same, with the
excaption that the mt7602 has been replaced with the mt7603. The internal wifi
setup has also changed slightly. Based on my tests, everything that worked on
the 2626 works on the 3526 and with roughly the same performance.
v1->v2:
* Remove some references to 2626 that I had missed in the dts.
v2->v3:
* Update patch to match new file structure.
* Removed SD driver to be consistent with other MT7621 targets.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
SVN-Revision: 49213
ELECOM WRH-300CR is MT7620N based very small Wi-Fi router with 64MiB
DDR2 SDRAM, 16MiB SPI Flash, one fast ethernet port, and (internal but
easy-to-access) UART.
it also has internal USB hub and USB card reader which provide one USB
port, one SD card slot, and one microSD card slot.
Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
Signed-off-by: FUKAUMI Naoki <naobsd@gmail.com>
SVN-Revision: 49211
This patch adds support for JHR-N805R, JHR-N825R and JHR-N926R to
various scripts in the base-files directory.
Signed-off-by: Reinhard Max <reinhard@m4x.de>
Reviewed-by: Torsten Duwe <duwe@lst.de>
SVN-Revision: 48905
This patch adds support for Phicomm PSG1208.This is a router with MT7620A SoC with 8M flash and 64M ram.
The WPS led is uesd as status_led because the power light can't be controlled with GPIO.
It seems that the 5g wifi led is connected to MT7612E and it can't be controlled with GPIO too.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
SVN-Revision: 48721
This patch adds support for the Netgear EX2700 and builds an approriate
sysupgrade image.
What's missing is the option to build a factory image flashable via the
router's stock web interface, but this approach is hindered by the fact
that u-boot operforms an additional integrity check, which expects a
uImage header in the last 64 bytes of the "kernel" partition, which
the bootloader expects to be 960k, a size exceeded by the standard
OpenWrt kernel.
Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
SVN-Revision: 48698
The board is based on mt7621AT cpu, and has 16mb nor flash, 256mb of ram,
2 sata ports, microsd card slot, 1 USB 3.0 port and at least one 2.4 and
one 5 ghz antenna.
This is the 6th submission that adds support for XHCI in the device tree
file, along with switching the location of the 2 radio's and addition of
the kmod-i2c-mt7621 in the default packages of the profile.
Signed-off-by: Sebastian Careba <nitroshift@yahoo.com>
SVN-Revision: 47845
The PBR-M1 support in current OpenWrt is for the early demo board and it doesn't work on the final board.This patch fixes the support for it.
The LED called pbr-m1:buzzer is a beeper connected to GPIO26 so I used gpio-beeper instead of gpio-leds.
Signed-off-by: 郭传鈜 <gch981213@gmail.com>
SVN-Revision: 47844
netis WF-2881 is an MT7621AT based router with MT7602EN, MT7612EN.
It has 128MB DDR3, 128MB SLC NAND FLASH, 5-port Gbps switch and 1x USB 3.0.
The following patch adds support for this device.
this device only works on top of UBI.
Tested and working:
* ethernet
* both WiFi radios
* USB 3.0
* buttons (reset button)
* ethernet switch and USB diag LEDs
* UART
* GPIOs
* sysupgrade
Tested and not working
* failsafe
Signed-off-by: YounJae Rho <luxflow@live.com>
SVN-Revision: 47619
HiWiFi HC5661/5761/5861 models are manufactured by http://www.hiwifi.com. These models have similar hardware specs(MT7620A + 128M DDR2 + 16M flash). This patch adds support for them.
The original author is Justin Liu (rssnsj@gmail.com). I ported the patch to trunk and submitted it here with his approval.
v3 fix
1: Fixed model order
2: Remove manufacturer name from model name
3: Use a hacky but prettier way to get mac address.
Signed-off-by: Xiaoning Kang <kangxn@163.com>
SVN-Revision: 47111
This patch is to add the WIZnet WizFi630A board as a new platform. The board is in mini pci express form factor.
Signed-off-by: Tobias Welz <tw@wiznet.eu>
SVN-Revision: 46921
This patch add support for Planex DB-WRT01. DANBOARD route on
the MT7620A SoC with two Ethernet port and a 802.11n 2.4 GHz radio.
DANBOARD is Cartoon character.
Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
SVN-Revision: 46918
Instead of using board name provided explicitly as text in LED name, ex.:
[...]
mlwg2)
status_led="mlwg2:blue:system"
[...]
use $board variable, which allows to combine together multiple boards with same color and LED names, ex:
[...]
mlw221|\
mlwg2)
status_led="$board:blue:system"
[...]
The above approach allows to shrink size of code in base-files/etc/board.d/01_leds and base-files/etc/diag.sh scripts dramatically.
One thing to keep in mind here is that we assume to use proper and consistent LED naming scheme ("device:color:led-name").
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46665
The upstream LED naming convention is "device:color:led-name", but it seems that many of supported boards in OpenWrt don't follow this approach.
The following patch fixes this inconsistency in dts{,i} files and updates base-files scripts for ramips target:
* fixes wrong indentation
* keeps case statements structure in same convention as in other scripts (no empty line after ";;", no indentation for case...esac body)
* fixes wrong LED names for some of boards (makes them the same as in dts{,i} files)
* combines boards with same configuration (ex. set_wifi_led "rt2800pci-phy0::radio" in 01_leds)
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46664
It seems that support for Edimax BR-6524N was dropped long time ago (dts file for this device is missing).
This patch removes remaining code.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46630
The following patch changes 7Links PX-4885 dts{,i} filenames, board, image and profile names from "PX4885" to "PX-4885" (for consistency).
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46629
The following patch changes Buffalo WMR-300 dts filename, board, image and profile names from "WMR300" to "WMR-300" (for consistency).
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46628
The following patch:
* changes board name from "argus-atp52b" to "atp-52b"
* changes dts filename
* fixes LED names in dts file and base-files scripts
* removes manufacturer name from image filename
for Argus ATP-52B device.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46621
The following patch:
* changes board name from "xiaomi-miwifi-mini" to "miwifi-mini"
* changes filenames of dts and profile
* fixes LED names in dts file and base-files scripts
* removes manufacturer name from image filename
for Xiaomi MiWiFi Mini device.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46617
There is another Zbtlink board (ZBT-WA05) supported in ramips target, so use the same naming scheme for ZBT-WR8305RT board and its dts file.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46614
STORYLiNK SAP-G3200U3 is an AC1200 router based on MT7621AT+MT7602EN+MT7612EN.
It has 128MB DDR3, 8MB NOR FLASH, 5-port Gbps switch and 1x USB 3.0.
The following patch adds support for this device.
Tested and working:
* ethernet
* both WiFi radios
* USB 3.0
* buttons
* ethernet switch and USB diag LEDs
* UART
* GPIOs
Tested and not working:
* LEDs for WiFi radios (connected with WiFi chips, not supported in mt76?)
* failsafe mode (known problem, needs workaround like other MTK based devices)
More information in Wiki: http://wiki.openwrt.org/toh/storylink/sap-g3200u3
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46454
This patch add support for Planex MZK-DP150N.
a mini router on the MT7620A SoC with one Ethernet port and a 802.11n 2.4 GHz radio.
Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
SVN-Revision: 46405
This patch adds support for the Linksys RE6500 Range Extender
http://wiki.openwrt.org/toh/linksys/re6500
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
SVN-Revision: 46043
This patch is for PandoraBox PBR-M1 which is based on mt7621,
all the features work fine, including rtc, leds, button, usb3.0, etc.
Signed-off-by: tymon <banglang.huang@foxmail.com>
SVN-Revision: 46041
The diag.sh script lacked an entry for the status led on the RT-N14U,
map it to the asus:blue:power led which is also used by the boot loader
to report boot status (eg. TFTP recovery mode VS normal boot)
Signed-off-by: Matteo Panella <m.panella@level28.org>
SVN-Revision: 45725
MR-102N is a RT3050F based wireless router(32M RAM + 8M NOR flash) with 1 USB
and 1 ethernet port. The original product information can be found at:
http://www.aximcom.com/en/MR-102N
Signed-off-by: Tai-hwa Liang <atliang@gmail.com>
SVN-Revision: 45724
This patch adds support for Comfast CF-WR800N, a wall-plug wireless router
based on the MT7620N SoC with one Ethernet port and a 802.11n 2.4 GHz radio.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
SVN-Revision: 45722
ZTE Q7 is a wireless router with SD Card,USB,1 ethernet port and a battery.It used MT7620a SoC.
I can,t find any information about this router on ZTE's website.
But I found this : http://en.cctairmobi.com/plus/list.php?tid=40
This router is the same as ZTE Q7 and later I found that both routers are made by the same company:-D
This patch adds support for it.
Because there is only one port,I disabled VLAN and use eth0 as lan port.
I could only create a sysupgrade firmware because I don't know how the orignal webpage check the uploaded image:-(
Signed-off-by: 郭传鈜 <gch981213@gmail.com>
SVN-Revision: 45208
I got work with this patch.
Ethernet switch (includes VLAN), WiFi connected via PCIe, LEDs, buttons.
In mtd partion map of DTS file, I renamed Linux firmware regions (kernel + root squashfs) to “firmware”because it allows kernel to split kernel and roots and rootfsdata.
signed-off-by: ngc@ff.iij4u.or.jp
——
——
SVN-Revision: 44470
MLW221 dts use tabs NOT spaces.
MLWG2 dts typo and 1 tab not spaces
01_leds and diag.sh cleanup
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
SVN-Revision: 44356
This patch adds support for Xiaomi MiWiFi Mini, a 802.11a/b/g/n/ac dual radio
wireless router based on the MediaTek MT7620a SoC.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
SVN-Revision: 44238
This adds support for a rt5350-based "portable nas" solution
from Intenso. The board comes with 32M RAM and 8M Flash, the
built-in HDD is connected/accessible via a usb3.0<->sata
bridge VLI VL701.
The device has 1 Ethernet port (100M/10M), 1 micro b usb 3.0
socket (for charging the battery, or accessing the hdd directly).
Wireless connectivity is provided by the rt5350 SoC [i.e.:
802.11n 1x1 2.4 GHz with a pcb antenna.]
Serial, leds, wifi, ethernet and usb are tested and
as far as I can tell: they are working fine (tm).
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
SVN-Revision: 44001
- Fix LED definitions.
- Add mode-switch slider definition (at GPIO 14).
- Remove unneeded VLAN now that the ethernet driver is fixed and TCP packets get passed correctly now. (This router only has one port.)
- Fix LAN port MAC address, which is defined in the factory partition as WLAN MAC address + 1.
- Fix board name, as the company name is HooToo and not HOOTOO.
- Remove unnecessary packages from the profile. (The end-user is supposed to use mechanisms such as the ImageBuilder in order to add his own set of packages to his own images... while the precompiled images should just contain the core set of packages needed to run the base functions of a wireless router.)
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
SVN-Revision: 43883
This new argument is used right after starting regular preinit (which
happens if failsafe wasn't triggered). The main purpose of "preinit"
argument is to indicate that failsafe can be triggered, however we were
missing a way to inform user that we don't wait for a trigger anymore.
With this change it's clear when failsafe mode can be triggered.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 43715
Aigale Ai-BR100 is a router with mt7620a soc.
There are only 2 lights on the board (WAN and WLAN) so I used the wlan light as the status led.
Signed-off-by: 郭传鈜 <gch981213@gmail.com>
SVN-Revision: 43681
