Backport 3 additional fixes for qca8k.
- Fix MTU calculation
- Fix a bug with config set to the wrong PAD when secondary cpu port is defined.
- Fix redundant check in parse_port_config
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
All patches automatically rebased.
Build system: x86_64
Build-tested: ramips/mt7621*
*Had to revert 7f1edbd in order to build due to FS#4149
Signed-off-by: John Audia <graysky@archlinux.us>
mtd: spi-nor: locking support for MX25L6405D
Macronix MX25L6405D supports locking with four block-protection bits.
Currently, the driver only sets three bits. If the bootloader does not
sustain the flash chip in an unlocked state, the flash might be
non-writeable. Add the corresponding flag to enable locking support with
four bits in the status register.
mtd: spi-nor: disable 16-bit-sr for macronix
Macronix flash chips seem to consist of only one status register.
These chips will not work with the "16-bit Write Status (01h) Command".
Disable SNOR_F_HAS_16BIT_SR for all Macronix chips.
Refreshed:
- 0052-mtd-spi-nor-use-4-bit-locking-for-MX25L12805D.patch
Fixes: 15aa53d7ee ("ath79: switch to Kernel 5.10")
Signed-off-by: Nick Hainke <vincent@systemli.org>
Linkstation poweroff driver was added to mvebu target, but is required
for kirkwood target too.
This commit make two changes:
- move linkstation-poweroff support patch from mvebu to generic and
replace upstream accepted version
- backport small linkstation-poweroff fix from 5.12
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
ath25 requires a 88E6060 driver to support boards such as Fonera 2.0g
(FON2202). The swconfig based mvswitch driver has not yet been ported to
the 5.10 kernel as the only user is the ath25 target while all other
targets have been switched to the upstream DSA implementation.
Switching ath25 to the DSA implementation is a complex task, since we
need either per-board platform data or DTS support. ath25 lacks both of
them and builds only a single generic image. So we need to keep the
swconfig driver implementation to easly and quickly port ath25 to the
5.10 kernel.
Since porting the mvswitch driver to 5.10 as a generic driver is not an
option, and since the ath25 is its only user, make mvswitch a target
specific driver to be able to port it to the 5.10 kernel as part of the
kernel version update of the target. This will allow us quickly migrate
to the next kernel version and not delay the next firmware release.
Suggested-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Assuming cmdlinepart is only one level deep partition scheme and that
static partition are also defined in DTS, we can assign an of_node for
partition declared from bootargs.
The cmdlinepart parser is the first parser checked and if it does find
some partition declared in the bootargs, every other parser is ignored.
This means that the fixed-partition parser is ignored and an of_node for
the mtd is never assigned.
Fix this by searching a defined of_node using a similar fixed_partition
parsing logig, check if a partition is present with the same label, check
that it has the same offset and size and finally assign an of_node to the
mtd. The NVMEM can now find the of_node for the mtd and correctly works.
Fixes: abc17bf306 ("ath79: convert mtd-mac-address to nvmem implementation")
Tested-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Copy and refresh patch enabling AQR112 and AQR412 Ethernet PHY from
layerscape (5.4) target to generic (5.10) as AQR112 can also be found
on other targets as well.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Each of
- CRYPTO_AEAD2
- CRYPTO_AEAD
- CRYPTO_GF128MUL
- CRYPTO_GHASH
- CRYPTO_HASH2
- CRYPTO_HASH
- CRYPTO_MANAGER2
- CRYPTO_MANAGER
- CRYPTO_NULL2
either directly required for mac80211 crypto support, or directly
selected by such options. Support for the mac80211 crypto was enabled in
the generic config since c7182123b9 ("kernel: make cryptoapi support
needed by mac80211 built-in"). So move the above options from the target
configs to the generic config to make it clear why do we need them.
CC: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Both CLANG_VERSION and LLD_VERISON are autogenerated runtime
configuration options, so add them to the kernel configuration filter
and remove from generic and per-target configs to keep configs clean.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Removed target for patch which does not exist:
bcm27xx/patches-5.10/950-0249-kbuild-Disable-gcc-plugins.patch
All patches automatically rebased.
Build system: x86_64
Build-tested: bcm2711/RPi4B, ipq806x/R7800*
Run-tested: bcm2711/RPi4B, ipq806x/R7800*
* Had to revert 7f1edbd412 in order to build
(binutils 2.37, https://bugs.openwrt.org/index.php?do=details&task_id=4149)
Signed-off-by: John Audia <graysky@archlinux.us>
All patches automatically rebased.
Build system: x86_64
Build-tested: ramips/mt7621*
*FS#4149 affects me so I had to revert 7f1edbd412
in order to downgrade to 2.35.1
Signed-off-by: John Audia <graysky@archlinux.us>
All patches automatically rebased.
Build system: x86_64
Build-tested: ramips/mt7621*
*FS#4149 affects me so I had to revert 7f1edbd412
in order to downgrade to 2.35.1
Signed-off-by: John Audia <graysky@archlinux.us>
The workqueue based implementation has a few corner cases and typically lower
performance than the upstream one
Signed-off-by: Felix Fietkau <nbd@nbd.name>
NET_DSA_MSCC_FELIX:
Marvell 88E6xxx Ethernet switch fabric support (NET_DSA_MV88E6XXX) [N/m/y/?] n
Ocelot / Felix Ethernet switch support (NET_DSA_MSCC_FELIX) [N/m/y/?] (NEW)
Error in reading or end of file.
make[6]: *** [scripts/kconfig/Makefile:71: syncconfig] Error 1
make[5]: *** [Makefile:603: syncconfig] Error 2
IR_IMON_RAW:
SoundGraph iMON Receiver (early raw IR models) (IR_IMON_RAW) [N/m/?] (NEW)
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
[squashed with "kernel: add missing IR_IMON_RAW config symbol"]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Deactivate all the symbols of the B53 DSA driver in the generic kernel
configuration. Multiple targets are now using this drivers and they
only need some of the options.
This fixes the bcm4908 build which didn't deactivate all of the options.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
All patches automatically rebased.
Build system: x86_64
Build-tested: ramips/mt7621*
*I am hit with the binutils 2.37 bug so I had to revert 7f1edbd412
in order to downgrade to 2.35.1
Signed-off-by: John Audia <graysky@archlinux.us>
Manually rebased:
generic-backport/850-v5.13-usb-ehci-add-spurious-flag-to-disable-overcurrent-ch.patch
All other patches automatically rebased.
Signed-off-by: John Audia <graysky@archlinux.us>
The crashlog patch as not ported to kernel 5.4.
Fixes: 4e0c54bc5b ("kernel: add support for kernel 5.4")
Signed-off-by: Jianhui Zhao <zhaojh329@gmail.com>
Fix mac address increment patch. Permit to overflow to the next
byte and correctly calculate the incremented mac.
Reported-by: Chen Minqiang <ptpt52@gmail.com>
Fixes: d284e6ef0f ("treewide: convert mtd-mac-address-increment* to generic implementation")
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Backport of Ansuel Smith's "net: dsa: qca8k: make sure PAD0 MAC06
exchange is disabled", to ensure mac06 is disabled even if enabled by
the bootloader.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Enabling KERNEL_UBSAN exposes several missing symbols. Add new kernel
build options for UBSAN_BOUNDS and UBSAN_TRAP, disable CONFIG_TEST_UBSAN
in the generic kernel configs and enable CONFIG_UBSAN_MISC in generic
5.10 config. The latter symbol was removed in later kernels, as it was
causing some issues, so just disable it in 5.10 instead of adding a
build option for it.
Fixes build failures with KERNEL_UBSAN enabled.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Enabling KERNEL_KASAN exposes several missing symbols. As KASAN_SW_TAGS
is only implemented for arm64 CPUs and requires clang, it doesn't make
sense to make this a build option so just default to KASAN_GENERIC and
disable KASAN_SW_TAGS.
While at it, disable TEST_KASAN_MODULE in the generic 5.10 config.
Fixes build failures with KERNEL_KASAN enabled.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
The qca8k patch series brings the numbering to 799. This patch renames
7xx patches to create space for more backports to be added.
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
[rename 729->719]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Removed upstreamed:
backport-5.4/790-v5.7-net-switchdev-do-not-propagate-bridge-updates-across.patch
All other patches automatically rebased.
Signed-off-by: John Audia <graysky@archlinux.us>
I had quite a hard time to understand what the change to net/core/dev.c
is supposed to do.
Simplify the change by returning NETDEV_TX_OK in case a eth_mangle_tx
callback was set but returned NULL instead of setting the return value
in the else branch.
Signed-off-by: Mathias Kresin <dev@kresin.me>
ar8216 switches have a hardware bug, which renders normal 802.1q support
unusable. Packet mangling is required to fix up the vlan for incoming
packets.
The patch was ommited at the time kernel 5.10 support was added but is
still required for ar8216 switches.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Don't patch the kernel to expose the partition name in sysfs as it is
already exposed via 'uevent'.
All previous users have been converted to use 'uevent', so we can
safely drop the custom patch.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This fixes support for Dongwon T&I DW02-412H which uses F25L16PA(2S) flash.
Signed-off-by: Jihoon Han <rapid_renard@renard.ga>
Reviewed-by: Sungbo Eo <mans0n@gorani.run>
[refresh patches]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Deleted (upstreamed):
bcm27xx/patches-5.10/950-0145-xhci-add-quirk-for-host-controllers-that-don-t-updat.patch [1]
Manually rebased:
bcm27xx/patches-5.10/950-0355-xhci-quirks-add-link-TRB-quirk-for-VL805.patch
bcm53xx/patches-5.10/180-usb-xhci-add-support-for-performing-fake-doorbell.patch
Note: although automatically rebaseable, the last patch has been edited to avoid
conflicting bit definitions.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=linux-5.10.y&id=b6f32897af190d4716412e156ee0abcc16e4f1e5
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
