This is a minor corrective release over GDB 11.1, fixing the following issues:
* PR sim/28302 (gdb fails to build with glibc 2.34)
* PR build/28318 (std::thread support configure check does not use CXX_DIALECT)
* PR gdb/28405 (arm-none-eabi: internal-error: ptid_t remote_target::select_thread_for_ambiguous_stop_reply(const target_waitstatus*): Assertion `first_resumed_thread != nullptr' failed)
* PR tui/28483 ([gdb/tui] breakpoint creation not displayed)
* PR build/28555 (uclibc compile failure since commit 4655f8509fd44e6efabefa373650d9982ff37fd6)
* PR rust/28637 (Rust characters will be encoded using DW_ATE_UTF)
* PR gdb/28758 (GDB 11 doesn't work correctly on binaries with a SHT_RELR (.relr.dyn) section)
* PR gdb/28785 (Support SHT_RELR (.relr.dyn) section)
The sizes of the ipk changed on mips 24Kc like this:
2285775 gdb_11.1-3_mips_24kc.ipk
2287441 gdb_11.2-4_mips_24kc.ipk
191828 gdbserver_11.1-3_mips_24kc.ipk
191811 gdbserver_11.2-4_mips_24kc.ipk
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add the most recent supported firmware file for Intel Wi-Fi 6E AX210
wireless chip. The API version 67 is not yet supported by the driver.
Additional PNVM file is required since API version 62.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Just use 'start' action which will have the desired effect instead of
trying to introduce a 'start_file' action which didn't work that way
because procd jshn magic would have to wrap around it.
Fixes: 88baf6ce2c ("ubox: only start log to file when filesystem has been mounted")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
From: Peter Lundkvist <peter.lundkvist@gmail.com>
This fixes the make_syscall_h.sh script to recognize both
__NR_Linux, used by mips, and __NR_SYSCALL_BASE and
__ARM_NR_BASE used by arm.
Run-tested on arm (ipq806x) and mips (ath79), both with glibc.
Compile-tested and checked resulting syscall_names.h file wuth
glibc: aarch64, powerpc, x86_64, i486
musl: arm, mips
Fixes: FS#4194, FS#4195
Signed-off-by: Peter Lundkvist <peter.lundkvist@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
If log_file is on an filesystem mounted using /etc/config/fstab we have
to wait for that to happen before starting the logread process.
Inhibit the start of the file-writer process and use a mount trigger to
fire it up once the filesystem actually becomes available.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Allow init scripts to trigger free-form actions by exposing
procd_add_action_mount_trigger.
Clean up mount trigger wrappers while at it to reduce code duplication.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The arc700 target is not booting up since some time, see here:
https://github.com/foss-for-synopsys-dwc-arc-processors/toolchain/issues/400
It looks like there is a problem in the toolchain when using glibc.
Currently no one is working on fixing this problem, remove the target
instead. This target also does not have many users we are aware of.
If someone wants to have this target back, feel free to add a fixed
version of this target again.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Stijn Tintel <stijn@linux-ipv6.be>
bpftool will enabled libbfd and libopcodes which gets picked up by perf
as libraries to link against. Add those missing dependencies when either
of these packages are enabled.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
nf-nathelper-extra and nf-conntrack-netlink had iptables related
dependencies, yet, when looking for the respective kernel symbols and
checking it's dependencies it was confirmed that iptables wasn't
required and that these were either it's own moodule or tool independent
(nftables or iptables).
Correct these and make sure no unneeded extras are pulled in.
Signed-off-by: Tiago Gaspar <tiagogaspar8@gmail.com>
Add U-Boot env settings to allow accessing the environment using
fw_printenv and fw_setenv tools on the UniElec U7623 board.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Brings bootmenu and production/recovery dual-boot scheme like on
the BPi-R2, BPi-R64, E8450 and UniFi 6 LR.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The ucode VM always passes 64bit integer values to sprintf implementation
while the `%d` format expects 32bit integers on 32bit platforms, leading
to incorrect formatting results.
Temporarily solve the issue by casting the numeric argument to int until
a more thorough fix arrives with the next update.
Fixes: FS#4234
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This removes -static compile option. The -static option tells GCC to
link this statically with the libc, which we do not want in OpenWrt. We
want to link everything dynamically to the libc. This fixes a compile
problem with glibc.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add the nohostroute option as available for gre and wg tunnels to
allow the user to prevent explicit creation of a route to the peer
address.
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Device specifications:
======================
* Qualcomm/Atheros AR7240 rev 2
* 350/350/175 MHz (CPU/DDR/AHB)
* 32 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2x 10/100 Mbps Ethernet
* 1T1R 2.4 GHz Wi-Fi
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x fast ethernet
- eth0
+ 18-24V passive POE (mode B)
+ used as WAN interface
- eth1
+ builtin switch port 4
+ used as LAN interface
* 12-24V 1A DC
* external antenna
The device itself requires the mtdparts from the uboot arguments to
properly boot the flashed image and to support dual-boot (primary +
recovery image). Unfortunately, the name of the mtd device in mtdparts is
still using the legacy name "ar7240-nor0" which must be supplied using the
Linux-specfic DT parameter linux,mtd-name to overwrite the generic name
"spi0.0".
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to the
device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Changes from 2.1.3 to 2.1.4:
Features:
- ubiscan debugging and statistics utility
Fixes:
- Some mtd-tests erroneously using sub-pages instead of the full page size
- Buffer overrun in fectest
- Missing jffs2 kernel header in the last release, leading to build
failures on some systems.
Changes from 2.1.2 to 2.1.3:
Features:
flashcp: Add new function that copy only different blocks
flash_erase: Add flash erase chip
Add flash_otp_erase
Add an ubifs mount helper
Add nandflipbits tool
Fixes:
mkfs.ubifs: Fix runtime assertions when running without crypto
mtd-utils: Use AC_SYS_LARGEFILE
Fix test binary installation
libmtd: avoid divide by zero
ubihealthd: fix UBIFS build dependency
mkfs.ubifs: remove OPENSSL_no_config()
misc-utils: Add fectest to build system
mkfs.ubifs: Fix build with SELinux
Fix typos found by Debian's lintian tool
Fix jffs2 build if zlib or lzo headers are not in default paths
Signed-off-by: Nick Hainke <vincent@systemli.org>
x86, mt7623 and others buildbot failed due to:
|Package kmod-hwmon-nct7802 is missing dependencies for the following libraries:
|regmap-core.ko
|regmap-i2c.ko
Fixes: 1ed50b92d1 ("package: kernel: add driver module for NCT7802Y")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This commit add package with hwmon-nct7802 module.
This driver implements support for the Nuvoton NCT7802Y hardware monitoring
chip. NCT7802Y supports 6 temperature sensors, 5 voltage sensors, and 3 fan
speed sensors.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
(fixed c&p'ed module description)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
SOC: IPQ4019
CPU: Quad-core ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
DRAM: 256 MB
NAND: 128 MiB Macronix MX30LF1G18AC
ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4x LAN, 1x WAN)
USB: 1x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
WLAN1: Qualcomm Atheros QCA4019 2.4GHz 802.11bgn 2x2:2
WLAN2: Qualcomm Atheros QCA9984 5GHz 802.11nac 4x4:4
INPUT: 1x WPS, 1x Reset
LEDS: Status, WIFI1, WIFI2, WAN (red & blue), 4x LAN
This board is very similar to the RT-ACRH13/RT-AC58U. It must be flashed
with an intermediary initramfs image, the jffs2 ubi volume deleted, and
then finally a sysupgrade with the final image performed.
Signed-off-by: Joshua Roys <roysjosh@gmail.com>
(added ALT0)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
OpenWrt plans to move over to firewall4 which uses nftables under the
hood. To allow a smooth migration the package `iptables-nft` offer a
transparent wrapper to apply iptables rules to nftables.
Without the config option for nftables the package isn't installed and
therefore can't be tested. This commit enabled it and therefore provides
the wrapper.
The size of the iptables package increases from 25436 to 26500 Bytes.
Signed-off-by: Paul Spooren <mail@aparcar.org>
ca6c35c uxc: usage message cosmetics
e083dd4 uxc: fix two minor issues reported by Coverity
35dfbff procd: jail/cgroups: correctly enable "rdma" when requested
3b3ac64 procd: mount /dev with noexec
ac2b8b3 procd: clean up /dev/pts mounts
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
0f16ea5 options.c: add DSCP code LE Least Effort
24ba465 firewall3: remove redundant syn check
df1306a firewall3: fix locking issue
3624c37 firewall3: support table load on access on Linux 5.15+
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Device specifications:
======================
* Qualcomm/Atheros QCA9558 ver 1 rev 0
* 720/600/240 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2T2R 2.4 GHz Wi-Fi (11n)
* 2T2R 5 GHz Wi-Fi (11ac)
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
* external h/w watchdog (enabled by default))
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* TI tmp423 (package kmod-hwmon-tmp421) for temperature monitoring
* 2x ethernet
- eth0
+ AR8035 ethernet PHY (RGMII)
+ 10/100/1000 Mbps Ethernet
+ 802.3af POE
+ used as LAN interface
- eth1
+ AR8035 ethernet PHY (SGMII)
+ 10/100/1000 Mbps Ethernet
+ 18-24V passive POE (mode B)
+ used as WAN interface
* 12-24V 1A DC
* internal antennas
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to the
device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Device specifications:
======================
* Qualcomm/Atheros AR9344 rev 2
* 560/450/225 MHz (CPU/DDR/AHB)
* 64 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 1T1R 2.4 GHz Wi-Fi
* 2T2R 5 GHz Wi-Fi
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* TI tmp423 (package kmod-hwmon-tmp421) for temperature monitoring
* 2x ethernet
- eth0
+ AR8035 ethernet PHY
+ 10/100/1000 Mbps Ethernet
+ 802.3af POE
+ used as LAN interface
- eth1
+ 10/100 Mbps Ethernet
+ builtin switch port 1
+ 18-24V passive POE (mode B)
+ used as WAN interface
* 12-24V 1A DC
* internal antennas
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to the
device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann <sven@narfation.org>
db7fb64 libopkg: pkg_hash: prefer to-be-installed packages
2edcfad libopkg: set 'const' attribute for argv
This should fix the ImageBuilder problems people are having since we
introduced the 'uci-firewall' providers.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
9a509d4 ruleset.uc: consolidate ip and ip6 offload
21f311d ruleset.uc: don't trim newline before comment sign
f121383 tests: enable flow offloading in tests
550df40 tests: add test for unknown defaults option
47c5a5b tests: add test for deprecated rule option
69a89d6 tests: add test for unknown rule option
07579df fw4.uc: handle interface zone option
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Almost all targets have the fixed-phy feature built into the kernel.
One big exception is x86. This caused a problem with the upcoming
LAN78xx usb driver. Hence this patch breaks out the fixed-phy from
of_mdio (which didn't include the .ko) and puts into a separate
module.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
phy drivers for Microchip's LAN88xx PHYs.
This is needed for the "LAN7801" variant
of the upstream lan78xx usb ethernet driver.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
libdw depends on libfts.so when building with the musl-libc library, add
this missing dependency.
Fixes: 6835ea13f0 ("elfutils: update to 0.186")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Linux upstream commit 9370f2d05a
add load firmware file through request_firmware,this affect the
nanopi r2s and some USB adapters in kernel 5.10 with this error:
'r8152 4-1:1.0: unable to load firmware patch rtl_nic/rtl8153b-2.fw'
This patch split the USB NIC firmware files from r8169 firmware,
and adds r8152-firmware to r8152 driver.
Add kmod-usb-net-cdc-ncm to support RTL8156A and RTL8156B 2.5G ethernet
adapters supported since v5.13-rc1.
195aae321c
Signed-off-by: Marty Jones <mj8263788@gmail.com>
Update busybox to 1.35.0
* refresh patches
Config refresh:
Refresh commands, run after busybox is first built once:
cd package/utils/busybox/config/
../convert_menuconfig.pl ../../../../build_dir/target-arm_cortex-a15+neon-vfpv4_musl_eabi/busybox-default/busybox-1.35.0
cd ..
./convert_defaults.pl ../../../build_dir/target-arm_cortex-a15+neon-vfpv4_musl_eabi/busybox-default/busybox-1.35.0/.config > Config-defaults.in
Manual edits needed after config refresh:
* Config-defaults.in: OpenWrt config symbol IPV6 logic applied to
BUSYBOX_DEFAULT_FEATURE_IPV6
* Config-defaults.in: OpenWrt configTARGET_bcm53xx logic applied to
BUSYBOX_DEFAULT_TRUNCATE (commit 547f1ec)
* Config-defaults.in: OpenWrt logic applied to
BUSYBOX_DEFAULT_LOGIN_SESSION_AS_CHILD (commit dc92917)
* config/editors/Config.in: Add USE_GLIBC dependency to
BUSYBOX_CONFIG_FEATURE_VI_REGEX_SEARCH (commit f141090)
* config/shell/Config.in : change at "Options common to all shells" the symbol
SHELL_ASH --> BUSYBOX_CONFIG_SHELL_ASH
(discussion in http://lists.openwrt.org/pipermail/openwrt-devel/2021-January/033140.html
Apparently our script does not see the hidden option while
prepending config options with "BUSYBOX_CONFIG_" which leads to a
missed dependency when the options are later evaluated.)
* Edit Config.in files by adding quotes to sourced items in
config/Config.in, config/networking/Config.in and config/util-linux/Config.in (commit 1da014f)
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
session tickets are a feature of TLSv1.2 and require less memory
and overhead on the server than does managing a session cache
Building mbedtls with support for session tickets will allow the
feature to be used with lighttpd-1.4.56 and later.
Signed-off-by: Glenn Strauss <gstrauss@gluelogic.com>
Specifications:
- SoC: MT7621DAT (880MHz, 2 Cores)
- RAM: 128 MB
- Flash: 128 MB NAND
- Ethernet: 5x 1GiE MT7530
- WiFi: MT7603/MT7613
- USB: 1x USB 3.0
This is another MT7621 device, very similar to other Linksys EA7300
series devices.
Installation:
Upload the generated factory.bin image via the stock web firmware
updater.
Reverting to factory firmware:
Like other EA7300 devices, this device has an A/B router configuration
to prevent bricking. Hard-resetting this device three (3) times will
put the device in failsafe (default) mode. At this point, flash the
OEM image to itself and reboot. This puts the router back into the 'B'
image and allows for a firmware upgrade.
Troubleshooting:
If the firmware will not boot, first restore the factory as described
above. This will then allow the factory.bin update to be applied
properly.
Signed-off-by: Nick McKinney <nick@ndmckinney.net>
CHECK_RUN_DIR=0 must be a part of MAKE_FLAGS, not MAKE_VARS, otherwise
it is not possible to compile mdadm on host without /run dir.
Signed-off-by: Sergey V. Lobanov <sergey@lobanov.in>
glibc version 2.34 does not provide versioned shared libraries any more,
it only provides shared libraries using the ABI version. Do not try to
copy them any more.
The functions from libpthread and librt were integrated into the main
binary, the libpthread.so and librt.so are only used for backwards
compatibility any more.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
