Commit Graph

60188 Commits

Author SHA1 Message Date
Radito Wahyu
5aca47bca1 ramips: add support for BOLT BL100
BL100 is a router made by Bolt by a provider in Indonesia
The original firmware created using Mediatek SDK and kernel 2.6.36

- Chipset: MediaTek MT7620A ver 2, eco 6
- RAM: 64 MB
- Bootloader: U Boot
- Flash: Winbond W25Q128BV (16 MB)
- Ports: 2x 10/100 Ethernet, 1x RJ-11 VoIP
- Modem: Qualcomm LTE B40 (2300 Mhz) VID:05c6 PID:9026
- Wireless: Internal MT7620A (2.4 Ghz) & Mediatek MT76x2E (5.8 Ghz)
- Switch: MediaTek MT7620A built-in 5-port 10/100M switch
- Voltage: DC 12V 1A
- Antenna Port: 2x External Antenna, 2 LTE U.FL, 2 WiFi U.FL
- Serial Port: Yes, 3.3 V TTL, Baud 57600 8N1
- Buttons: Reset and WPS
- LED: 15 Total
  - 4 blue lte, 2 red lte, 1 reset, 1 power.
  - 1 wps, 1 voip, 1 wlan2, 1 wlan5, 1 lan, 1 wan, 1 wlan.

Installation via stock firmware
1. Unlock Telnet access by downloading the backup .tar.gz file
2. Change the Telnet configuration to LAN_Telnet=1
3. Import backup configuration
4. Restart the router
5. Login to telnet with username and password = admin : db40
6. Download sysupgrade binary and mtd_write to the kernel partition
`mtd_write write openwrt-bolt_bl100-squashfs-sysupgrade.bin Kernel`

Signed-off-by: Radito Wahyu <arditogits@gmail.com>
2024-03-31 20:07:45 +02:00
Felix Fietkau
a112ed4126 unetd: update to Git HEAD (2024-03-31)
52144f723bec pex: after receiving data update req, notify peer of local address/port
29aacb9386e0 pex: track indirect hosts (reachable via gateway) as peers without adding them to wg
48049524d4fc pex: do not send peer notifications for hosts with a gateway
12ac684ee22a pex: do not query for hosts with a gateway
203c88857354 pex: fix endian issues on config transfer
a29d45c71bca network: fix endian issue in converting port to network id
cbbe9d337a17 unet-cli: emit id by default
806457664ab6 unet-cli: strip initial newline in usage message

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2024-03-31 19:42:30 +02:00
Roland Reinl
29cca6cfee filogic: Add support for D-Link AQUILA PRO AI M30
Specification:
 - MT7981 CPU using 2.4GHz and 5GHz WiFi (both AX)
 - MT7531 switch
 - 512MB RAM
 - 128MB NAND flash with two UBI partitions with identical size
 - 1 multi color LED (red, green, blue, white) connected via GCA230718
 - 3 buttons (WPS, reset, LED on/off)
 - 1 1Gbit WAN port
 - 4 1Gbit LAN ports

Disassembly:
 - There are four screws at the bottom: 2 under the rubber feets, 2 under the label.
 - After removing the screws, the white plastic part can be shifted out of the blue part.
 - Be careful because the antennas are mounted on the side and the top of the white part.

Serial Interface
 - The serial interface can be connected to the 4 pin holes on the side of the board.
 - Pins (from front to rear):
   - 3.3V
   - RX
   - TX
   - GND
 - Settings: 115200, 8N1

MAC addresses:
 - WAN MAC is stored in partition "Odm" at offset 0x81
 - LAN (as printed on the device) is WAN MAC + 1
 - WLAN MAC (2.4 GHz) is WAN MAC + 2
 - WLAN MAC (5GHz) is WAN MAC + 3

Flashing via Recovery Web Interface:
 - The recovery web interface always flashes to the currently active partition.
 - If OpenWrt is flahsed to the second partition, it will not boot.
 - Ensure that you have an OEM image available (encrypted and decrypted version). Decryption is described in the end.
 - Set your IP address to 192.168.200.10, subnetmask 255.255.255.0
 - Press the reset button while powering on the device
 - Keep the reset button pressed until the LED blinks red
 - Open a Chromium based and goto http://192.168.200.1 (recovery web interface)
 - Download openwrt-mediatek-filogic-dlink_aquila-pro-ai-m30-a1-squashfs-recovery.bin
 - The recovery web interface always reports successful flashing, even if it fails
 - After flashing, the recovery web interface will try to forward the browser to 192.168.0.1 (can be ignored)
 - If OpenWrt was flashed to the first partition, OpenWrt will boot (The status LED will start blinking white and stay white in the end). In this case you're done and can use OpenWrt.
 - If OpenWrt was flashed to the second partition, OpenWrt won't boot (The status LED will stay red forever). In this case, the following steps are reuqired:
   - Start the web recovery interface again and flash the **decrypted OEM image**. This will be flashed to the second partition as well. The OEM firmware web interface is afterwards accessible via http://192.168.200.1.
   - Now flash the **encrypted OEM image** via OEM firmware web interface. In this case, the new firmware is flashed to the first partition. After flashing and the following reboot, the OEM firmware web interface should still be accessible via http://192.168.200.1.
   - Start the web recovery interface again and flash the OpenWrt recovery image. Now it will be flashed to the first partition, OpenWrt will boot correctly afterwards and is accessible via 192.168.1.1.

Flashing via U-Boot:
 - Open the case, connect to the UART console
 - Set your IP address to 192.168.200.2, subnet mask 255.255.255.0. Connect to one of the LAN interfaces of the router
 - Run a tftp server which provides openwrt-mediatek-filogic-dlink_aquila-pro-ai-m30-a1-initramfs-kernel.bin.
 - Power on the device and select "7. Load image" in the U-Boot menu
 - Enter image file, tftp server IP and device IP (if they differ from the default).
 - TFTP download to RAM will start. After a few seconds OpenWrt initramfs should start
 - The initramfs is accessible via 192.168.1.1, change your IP address accordingly (or use multiple IP addresses on your interface)
 - Perform a sysupgrade using openwrt-mediatek-filogic-dlink_aquila-pro-ai-m30-a1-squashfs-sysupgrade.bin
 - Reboot the device. OpenWrt should start from flash now

Revert back to stock using the Recovery Web Interface:
 - Set your IP address to 192.168.200.2, subnetmask 255.255.255.0
 - Press the reset button while powering on the device
 - Keep the reset button pressed until the LED blinks red
 - Open a Chromium based and goto http://192.168.200.1 (recovery web interface)
 - Flash a decrypted firmware image from D-Link. Decrypting an firmware image is described below.

Decrypting a D-Link firmware image:
 - Download https://github.com/RolandoMagico/firmware-utils/blob/M32/src/m32-firmware-util.c
 - Compile a binary from the downloaded file, e.g. gcc m32-firmware-util.c -lcrypto -o m32-firmware-util
 - Run ./m32-firmware-util M30 --DecryptFactoryImage <OriginalFirmware> <OutputFile>
 - Example for firmware M30A1_FW101B05: ./m32-firmware-util M30 --DecryptFactoryImage M30A1_FW101B05\(0725091522\).bin M30A1_FW101B05\(0725091522\)_decrypted.bin

Flashing via OEM web interface is not possible, as it will change the active partition and OpenWrt is only running on the first UBI partition.

Controlling the LEDs:
 - The LEDs are controlled by a chip called "GCA230718" which is connected to the main CPU via I2C (address 0x40)
 - I didn't find any documentation or driver for it, so the information below is purely based on my investigations
 - If there is already I driver for it, please tell me. Maybe I didn't search enough
 - I implemented a kernel module (leds-gca230718) to access the LEDs via DTS
 - The LED controller supports PWM for brightness control and ramp control for smooth blinking. This is not implemented in the driver
 - The LED controller supports toggling (on -> off -> on -> off) where the brightness of the LEDs can be set individually for each on cycle
 - Until now, only simple active/inactive control is implemented (like when the LEDs would have been connected via GPIO)
 - Controlling the LEDs requires three sequences sent to the chip. Each sequence consists of
   - A reset command (0x81 0xE4) written to register 0x00
   - A control command (for example 0x0C 0x02 0x01 0x00 0x00 0x00 0xFF 0x01 0x00 0x00 0x00 0xFF 0x87 written to register 0x03)
 - The reset command is always the same
 - In the control command
   - byte 0 is always the same
   - byte 1 (0x02 in the example above) must be changed in every sequence: 0x02 -> 0x01 -> 0x03)
   - byte 2 is set to 0x01 which disables toggling. 0x02 would be LED toggling without ramp control, 0x03 would be toggling with ramp control
   - byte 3 to 6 define the brightness values for the LEDs (R,G,B,W) for the first on cycle when toggling
   - byte 7 defines the toggling frequency (if toggling enabled)
   - byte 8 to 11 define the brightness values for the LEDs (R,G,B,W) for the second on cycle when toggling
   - byte 12 is constant 0x87

Comparison to M32/R32:
 - The algorithms for decrypting the OEM firmware are the same for M30/M32/R32, only the keys differ
 - The keys are available in the GPL sources for the M32
 - The M32/R32 contained raw data in the firmware images (kernel, rootfs), the R30 uses a sysupgrade tar instead
 - Creation of the recovery image is quite similar, only the header start string changes. So mostly takeover from M32/R32 for that.
 - Turned out that the bytes at offset 0x0E and 0x0F in the recovery image header are the checksum over the data area
 - This checksum was not checked in the recovery web interface of M32/R32 devices, but is now active in R30
 - I adapted the recovery image creation to also calculate the checksum over the data area
 - The recovery image header for M30 contains addresses which don't match the memory layout in the DTS. The same addresses are also present in the OEM images
 - The recovery web interface either calculates the correct addresses from it or has it's own logic to determine where which information must be written

Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
2024-03-31 19:01:20 +02:00
Roland Reinl
0e2b7e3bd6 mediatek: Moved recovery image creation to include/image-commands.mk
The recovery image is reqired for D-Link M30 as well. So I moved it to include/image-commands.mk to be able to use it for MT7622 and filogic devices.

Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
2024-03-31 19:01:20 +02:00
Roland Reinl
0682974aa8 filogic: Add LED driver for GCA230718
Add basic support for the LED driver for GCA230718.

 - I didn't find any documentation or driver for it, so the information below is purely based on my investigations
 - If there is already I driver for it, please tell me. Maybe I didn't search enough
 - I implemented a kernel module (leds-gca230718) to access the LEDs via DTS
 - The LED controller supports PWM for brightness control and ramp control for smooth blinking. This is not implemented in the driver
 - The LED controller supports toggling (on -> off -> on -> off) where the brightness of the LEDs can be set individually for each on cycle
 - Until now, only simple active/inactive control is implemented (like when the LEDs would have been connected via GPIO)
 - Controlling the LEDs requires three sequences sent to the chip. Each sequence consists of
   - A reset command (0x81 0xE4) written to register 0x00
   - A control command (for example 0x0C 0x02 0x01 0x00 0x00 0x00 0xFF 0x01 0x00 0x00 0x00 0xFF 0x87 written to register 0x03)
 - The reset command is always the same
 - In the control command
   - byte 0 is always the same
   - byte 1 (0x02 in the example above) must be changed in every sequence: 0x02 -> 0x01 -> 0x03)
   - byte 2 is set to 0x01 which disables toggling. 0x02 would be LED toggling without ramp control, 0x03 would be toggling with ramp control
   - byte 3 to 6 define the brightness values for the LEDs (R,G,B,W) for the first on cycle when toggling
   - byte 7 defines the toggling frequency (if toggling enabled)
   - byte 8 to 11 define the brightness values for the LEDs (R,G,B,W) for the second on cycle when toggling
   - byte 12 is constant 0x87

Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
2024-03-31 19:01:19 +02:00
Hauke Mehrtens
fb2c6e9d4d kernel: bump 5.15 to 5.15.153
Removed because they are upstream:
generic/backport-5.15/704-15-v5.19-net-mtk_eth_soc-move-MAC_MCR-setting-to-mac_finish.patch
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=linux-5.15.y&id=c5c0760adc260d55265c086b9efb350ea6dda38b

generic/pending-5.15/735-net-mediatek-mtk_eth_soc-release-MAC_MCR_FORCE_LINK-.patch
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=linux-5.15.y&id=448cc8b5f743985f6d1d98aa4efb386fef4c3bf2

generic/pending-5.15/736-net-ethernet-mtk_eth_soc-fix-PPE-hanging-issue.patch
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=linux-5.15.y&id=9fcadd125044007351905d40c405fadc2d3bb6d6

Add new configuration symbols for tegra target.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-03-31 18:34:04 +02:00
John Audia
b04f245c39 kernel: bump 6.6 to 6.6.23
Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.6.23

Removed upstreamed:
  pending-6.6/735-net-mediatek-mtk_eth_soc-release-MAC_MCR_FORCE_LINK-.patch[1]
  pending-6.6/736-net-ethernet-mtk_eth_soc-fix-PPE-hanging-issue.patch[2]
  mediatek/patches-6.6/232-clk-mediatek-mt7981-topckgen-flag-SGM_REG_SEL-as-cri.patch[3]

Manually rebased:
  mediatek/patches-6.6/100-dts-update-mt7622-rfb1.patch

Added:
  generic/backports-6.6/981-mtd-spinand-Add-support-for-5-byte-IDs.patch[4]

All other patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.23&id=1f32abb474c1c9bdb21d9eda74c325a0b3a162e5
2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.23&id=943c14ece95eb1cf98d477462aebcbfdfd714633
3. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.23&id=6ff01b314149d1cf59caebc29384f0beed21cba4
4. See comments in https://github.com/openwrt/openwrt/pull/14992 regarding broken flogic/xiaomi_redmi-router-ax6000-ubootmod

Build system: x86/64
Build-tested: x86/64/AMD Cezanne, flogic/xiaomi_redmi-router-ax6000-ubootmod, flogic/glinet_gl-mt6000
Run-tested: x86/64/AMD Cezannei, flogic/xiaomi_redmi-router-ax6000-ubootmod, flogic/glinet_gl-mt6000

Signed-off-by: John Audia <therealgraysky@proton.me>
2024-03-31 18:19:33 +02:00
Marco von Rosenberg
06cdc07f8c ath79: add support for Huawei AP5030DN
Huawei AP5030DN is a dual-band, dual-radio 802.11ac Wave 1 3x3 MIMO
enterprise access point with two Gigabit Ethernet ports and PoE
support.

Hardware highlights:
- CPU: QCA9550 SoC at 720MHz
- RAM: 256MB DDR2
- Flash: 32MB SPI-NOR
- Wi-Fi 2.4GHz: QCA9550-internal radio
- Wi-Fi 5GHz: QCA9880 PCIe WLAN SoC
- Ethernet 1: 10/100/1000 Mbps Ethernet through Broadcom B50612E PHY
- Ethernet 2: 10/100/1000 Mbps Ethernet through Marvell 88E1510 PHY
- PoE: input through Ethernet 1 port
- Standalone 12V/2A power input
- Serial console externally available through RJ45 port
- External watchdog: SGM706 (1.6s timeout)

Serial console:
  9600n8 (9600 baud, no stop bits, no parity, 8 data bits)

MAC addresses:
  Each device has 32 consecutive MAC addresses allocated by
  the vendor, which don't overlap between devices.
  This was confirmed with multiple devices with consecutive
  serial numbers.
  The MAC address range starts with the address on the label.
  To be able to distinguish between the interfaces,
  the following MAC address scheme is used:
    - eth0 = label MAC
    - eth1 = label MAC + 1
    - radio0 (Wi-Fi 5GHz) = label MAC + 2
    - radio1 (Wi-Fi 2.4GHz) = label MAC + 3

Installation:
0. Connect some sort of RJ45-to-USB adapter to "Console" port of the AP

1. Power up the AP

2. At prompt "Press f or F  to stop Auto-Boot in 3 seconds",
   do what they say.
   Log in with default admin password "admin@huawei.com".

3. Boot the OpenWrt initramfs from TFTP using the hidden script
   "run ramboot". Replace IP address as needed:

   > setenv serverip 192.168.1.10
   > setenv ipaddr 192.168.1.1
   > setenv rambootfile
     openwrt-ath79-generic-huawei_ap5030dn-initramfs-kernel.bin
   > saveenv
   > run ramboot

4. Optional but recommended as the factory firmware cannot
   be downloaded publicly:
   Back up contents of "firmware" partition using the web interface or ssh:

   $ ssh root@192.168.1.1 cat /dev/mtd11 > huawei_ap5030dn_fw_backup.bin

5. Run sysupgrade using sysupgrade image. OpenWrt
   shall boot from flash afterwards.

Return to factory firmware (using firmware upgrade package downloaded from
non-public Huawei website):
1. Start a TFTP server in the directory where
   the firmware upgrade package is located

2. Boot to u-boot as described above

3. Install firmware upgrade package and format the config partitions:

   > update system FatAP5X30XN_SOMEVERSION.bin
   > format_fs

Return to factory firmware (from previously created backup):
1. Copy over the firmware partition backup to /tmp,
   for example using scp

2. Use sysupgrade with force to restore the backup:
   sysupgrade -F huawei_ap5030dn_fw_backup.bin

3. Boot AP to U-Boot as described above

Quirks and known issues
-----------------------

- On initial power-up, the Huawei-modified bootloader suspends both
ethernet PHYs (it sets the "Power Down" bit in the MII control
register). Unfortunately, at the time of the initial port, the kernel
driver for the B50612E/BCM54612E PHY behind eth0 doesn't have a resume
callback defined which would clear this bit. This makes the PHY unusable
since it remains suspended forever. This is why the backported kernel
patches in this commit are required which add this callback and for
completeness also a suspend callback.

- The stock firmware has a semi dual boot concept where the primary
kernel uses a squashfs as root partition and the secondary kernel uses
an initramfs. This dual boot concept is circumvented on purpose to gain
more flash space and since the stock firmware's flash layout isn't
compatible with mtdsplit.

- The external watchdog's timeout of 1.6s is very hard to satisfy
during bootup. This is why the GPIO15 pin connected to the watchdog input
is configured directly in the LZMA loader to output the CPU_CLK/4 signal
which keeps the watchdog happy until the wdt-gpio kernel driver takes
over. Because it would also take too long to read the whole kernel image
from flash, the uImage header only includes the loader which then reads
the kernel image from flash after GPIO15 is configured.

Signed-off-by: Marco von Rosenberg <marcovr@selfnet.de>
[fixed 6.6 backport patch naming]
Signed-off-by: David Bauer <mail@david-bauer.net>
2024-03-31 18:09:43 +02:00
Felix Fietkau
0cb3e86557 kernel: fix build issue on macOS
On x86, the build failed while trying to compile tools/lib/string.c because
of a clash with the system provided implementation for strlcpy
Add ifdefs to prevent the conflict.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2024-03-30 21:59:24 +01:00
Robert Marko
0c96d20bf9 tools: b43-tools: fix compilation with GCC14
GCC14 no longer treats integer types and pointer types as equivalent in
assignments (including implied assignments of function arguments and return
values), and instead fails the compilation with a type error.

So, as a workaround lets disable the newly introduced error
-Werror=int-conversion and just make it print a warning to enable compiling
with GCC14 as Fedora 40 now defaults to it.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-03-30 10:42:47 +01:00
Shiji Yang
d7d94a8d91 uboot-envtools: ath79: remove D-Link DIR-8x9 and DAP-1720 env config
The uboot-envtools can automatically parse the dts 'u-boot,env'
compatible string. So the env config file is now useless.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2024-03-30 01:04:17 +01:00
Shiji Yang
085feb60ad ath79: move D-Link DAP-1720 A1 to tiny sub-target
This device only has 64 MiB RAM and ath10k wireless driver will
consume a lot of memory. Let's move it to the tiny sub-target to
get extra 7 MiB of free space. In this way, we can extend their
lifetime to receive support for the next OpenWrt LTS version. This
patch also trims the duplicate "recovery.bin" image as it's the
same as the "factory.bin".

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2024-03-30 01:04:17 +01:00
Shiji Yang
8201e402c5 ath79: move D-Link DIR-859 and DIR-869 series to tiny sub-target
These devices only have 64 MiB RAM and ath10k wireless driver will
consume a lot of memory. Let's move them to the tiny sub-target to
get extra 7 MiB of free space. In this way, we can extend their
lifetime to receive support for the next OpenWrt LTS version. This
patch also trims the USB package for the non-existent USB port.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2024-03-30 01:04:17 +01:00
Shiji Yang
9a6c1846bb ath79: tiny: enable NVMEM u-boot-env driver
The upcoming D-Link devices to the tiny sub-target require it to
parse the u-env MAC address. The kernel size will increase by
about 1 KiB.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2024-03-30 01:04:17 +01:00
Shiji Yang
82208eb527 ath79: move seama image recipe to the common Makefile
Move seama image recipe to the common Makefile in order for some
tiny sub-target D-Link devices can share it.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2024-03-30 01:04:17 +01:00
Shiji Yang
60061b5c26 ath79: disable building small Flash EnGenius devices
The buildbot has not successfully built them for a long time due
to small Flash size.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2024-03-30 01:04:17 +01:00
Rosen Penev
cd5c0054bd dtc: fix compilation with both libraries
Upstream backports.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2024-03-29 23:42:22 +01:00
Rosen Penev
d08ff66fcd tools/meson: static host and both libraries
Host packages typically are statically linked to avoid rpath issues and
to avoid libraries not being found as a result. With target packages,
both libraries make the most sense as InstallDev typically installs
both, giving packages flexibility. Default this behavior.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2024-03-29 23:42:22 +01:00
Rosen Penev
fcdc629144 tools/meson: update to 1.3.2
Add explicit setup as implicit is deprecated.

Rename pkgconfig as no hyphen is deprecated.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2024-03-29 23:42:22 +01:00
Chukun Pan
4ae474afbd mediatek: filogic: add Netcore N60 support
Hardware specification:
  SoC: MediaTek MT7986A 4x A53
  Flash: ESMT F50L1G41LB 128MB
  RAM: W632GU6NB DDR3 256MB
  Ethernet: 1x 2.5G + 4x 1G
  WiFi1: MT7975N 2.4GHz 4T4R
  WiFi2: MT7975PN 5GHz 4T4R
  Button: Reset, WPS
  Power: DC 12V 2A

Flash instructions:
  1. Connect to the router using ssh or telnet,
     username: useradmin, password is the web
     login password of the router.
  2. Use scp to upload bl31-uboot.fip and flash:
     "mtd write xxx-preloader.bin spi0.0"
     "mtd write xxx-bl31-uboot.fip FIP"
     "mtd erase ubi"
  3. Connect to the router via the Lan port,
     set a static ip of your PC.
     (ip 192.168.1.254, gateway 192.168.1.1)
  4. Download initramfs image, reboot router,
     waiting for tftp recovery to complete.
  5. After openwrt boots up, perform sysupgrade.

Note:
  1. Back up all mtd partitions before flashing.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2024-03-29 22:54:28 +01:00
Chukun Pan
0170666d89 uboot-mediatek: add Netcore N60 support
The vendor uboot requires special fit verification.
So add a custom uboot build for this device.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2024-03-29 22:53:53 +01:00
Mieczyslaw Nalewaj
362e7103c6 ramips: mt7620a_tplink_archer-c5-v4: use LED_FUNCTION_WLAN_2GHZ and LED_FUNCTION_WLAN_5GHZ
Use LED_FUNCTION_WLAN_2GHZ and LED_FUNCTION_WLAN_5GHZ instead function-enumerator

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
2024-03-29 20:10:42 +01:00
Florian Eckert
a998a12a2f imagebuilder: add check if target is sourced from feed
The image generation would fail, if the target is included from a feed.
To fix this, check if targets is found in the feed directory.

Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Tested-by: Thomas Richard <thomas.richard@bootlin.com>
2024-03-29 20:00:27 +01:00
Florian Eckert
27d227b682 imagebuilder: check if BOARD is located in the feeds sub directory
Fixes the regression so that targets that were installed via a feed can
also be build again with the Image Builder.

Fixes: 84ec8c4 ("imagebuilder: copy from buildroot only target/linux")
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Tested-by: Thomas Richard <thomas.richard@bootlin.com>
2024-03-29 20:00:27 +01:00
Tianling Shen
163c3d0bde rockchip: remove redundant 'console' parameter from boot script
ttyS2 is the default console used for all rockchip boards.
The redundant 'console=tty1' parameter now breaks the console due to
recent procd update.

Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2024-03-29 19:34:42 +01:00
Tianling Shen
50e6c8ae8d rockchip: remove 'swiotlb' parameter from boot script
We have hardware IOMMU support and this is totally unnecessary.
The given value is also unreasonable, it's too small and causes
kernel panic in some cases:

[ 5706.856473] sdhci-dwcmshc fe310000.mmc: swiotlb buffer is full (sz: 28672 bytes), total 512 (slots), used 498 (slots)
[ 5706.864451] sdhci-dwcmshc fe310000.mmc: swiotlb buffer is full (sz: 65536 bytes), total 512 (slots), used 464 (slots)

This parameter seems to be added by mistake, so remove it.

Fixes: e35c7ab51f ("rockchip: merge bootscript")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2024-03-29 19:34:42 +01:00
Robert Marko
5876b4afb9 qualcommax: default to kernel 6.6
6.6 has been in testing on qualcommax for a while so it should be in a
good shape, but lets default to it to get a wider audience.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-03-29 18:56:31 +01:00
Petr Štetiar
d4b6b76443
Revert "tools/xz: update to 5.6.1" (CVE-2024-3094)
This reverts commit 714c91d1a6 as probably
the upstream xz repository and the xz tarballs have been backdoored.

References: https://www.openwall.com/lists/oss-security/2024/03/29/4.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2024-03-29 16:59:56 +00:00
Jordan Woyak
f9f2426e39 config: Enable ext4 journaling by default.
Not having a journal by default is a major "gotcha".

Because openwrt does not fsck on boot, a power loss without journaling
can result in a dirty filesystem that openwrt will mount as read-only
which requires intervention to restore the router to working order.

Signed-off-by: Jordan Woyak <jordan.woyak@gmail.com>
2024-03-29 17:49:53 +01:00
Tomasz Maciej Nowak
d506ea3e80 kernel: kmod-phy-smsc: add dependency on crc16
Introduced WoL feature needs CRC16 support.

Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
2024-03-29 17:32:26 +01:00
Felix Fietkau
87de62dcb8 perf: fix build on linux 6.6
- use Makefile.perf to prevent overriding MAKEFLAGS
- fix path to PKG_CONFIG
- link libstdc++ statically (only used for demangling)

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2024-03-29 15:41:16 +01:00
Felix Fietkau
383b68e73c tools/cmake: disable xcode generator
Fixes build on latest macOS SDK

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2024-03-29 15:40:25 +01:00
Felix Fietkau
c9ae8fd3d4 tools/e2fsprogs: disable building fuse2fs to avoid depending on libfuse
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2024-03-29 15:39:04 +01:00
Hauke Mehrtens
2ec025d554 kernel: bump 5.15 to 5.15.152
Removed because it is upstream:
generic/backport-5.15/081-v5.17-regmap-allow-to-define-reg_update_bits-for-no-bus.patch
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=linux-5.15.y&id=fbddd48f1456db32b675fad95a902de38345902a

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-03-29 13:44:41 +01:00
Hauke Mehrtens
0307571124 kernel: bump 5.15 to 5.15.151
No manual changes needed.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-03-29 13:44:41 +01:00
Florian Eckert
535d487c41 linux-firmware: add missing LICENSE_FILES info
Where it is clear which lincense the firmware package has, the missing
information are added.

Signed-off-by: Florian Eckert <fe@dev.tdt.de>
2024-03-29 13:11:47 +01:00
Florian Eckert
5c14de1d7e linux-firmware: add LICENSE_FILES and LICENSE file handling
The firmware blobs have all different licenses from the different
manufacturers of the binary blobs. This information is contained in the
upstream 'linux-firmware' repositroy.

This commit extends the package handling so that this information can be
added as an additional argument during packages generation.

Signed-off-by: Florian Eckert <fe@dev.tdt.de>
2024-03-29 13:11:47 +01:00
Robert Marko
b1d579f174 archs38: remove 5.15 support
Since 6.1 is now default, drop 5.15 support.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-03-29 09:58:45 +01:00
Robert Marko
00c26f4728 archs38: default to kernel 6.1
Default to kernel 6.1 on archs38.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-03-29 09:58:45 +01:00
Mieczyslaw Nalewaj
de8a6ce5ea generic: 6.6: add kernel missing symbol
Add missing symbol CONFIG_SSIF_IPMI_BMC causing bcm53xx compilation errors.

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
2024-03-29 09:58:18 +01:00
Nick Hainke
b05aad58e8 tools/cmake: update to 3.29.0
Changelog:
- https://www.kitware.com/cmake-3-29-0-available-for-download/

Refresh patches:
- 120-curl-fix-libressl-linking.patch
- 130-bootstrap_parallel_make_flag.patch
- 150-zstd-libarchive.patch

Signed-off-by: Nick Hainke <vincent@systemli.org>
2024-03-29 07:18:07 +01:00
Nick Hainke
714c91d1a6 tools/xz: update to 5.6.1
Change mirror to github.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2024-03-29 06:56:43 +01:00
Rafał Miłecki
eb370ebc5f bcm47xx: refresh kernel 6.1 config
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2024-03-29 00:12:50 +01:00
Rafał Miłecki
8583a97c06 bcm47xx: add testing support for kernel 6.1
Tested on Luxul XWR-1750 (BCM4706). Working: switch (LAN, WAN), LEDs,
sysupgrade.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2024-03-29 00:11:04 +01:00
Rafał Miłecki
d4a40827ba bcm4908: refresh kernel 6.6 config
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2024-03-28 13:29:52 +01:00
Rafał Miłecki
c3dc52fb3c bcm4008: prepare to work on kernel 6.6
Don't add KERNEL_TESTING_PATCHVER yet as there are some issues with it.

On TP-Link Archer C2300 serial console seems to stop working after
preinit:
> Press the [f] key and hit [enter] to enter failsafe mode
> Press the [1], [2], [3] or [4] key and hit [enter] to select the de�

On Netgear R8000P XHCI causes external abort:
[    2.139586] Internal error: synchronous external abort: 0000000096000210 [#1] SMP
[    2.147212] Modules linked in: xhci_plat_hcd(+) xhci_hcd ohci_platform ohci_hcd fsl_mph_dr_of ehci_platform ehci_fsl ehci_hcd gpio_button_hotplug(O) usbcore nls_base usb_common crc32c_generic
[    2.164774] CPU: 0 PID: 358 Comm: kmodloader Tainted: G           O       6.6.22 #0
[    2.172658] Hardware name: Netgear R8000P (DT)
[    2.177229] pstate: 60400005 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[    2.184395] pc : xhci_gen_setup+0x80/0x34c [xhci_hcd]
[    2.189591] lr : xhci_gen_setup+0x74/0x34c [xhci_hcd]
[    2.194788] sp : ffffffc0815d37b0
[    2.198194] x29: ffffffc0815d37b0 x28: ffffff8002000000 x27: ffffff8001172d88
[    2.205540] x26: ffffff8002000000 x25: 0000000000000000 x24: ffffffc078b603c0
[    2.212888] x23: ffffffc078b2a008 x22: ffffff8001172c10 x21: ffffff8002000000
[    2.220235] x20: ffffff8002000000 x19: ffffff8002000250 x18: 0000000000000000
[    2.227582] x17: 626d756e20737562 x16: 2064656e67697373 x15: ffffffffffffffff
[    2.234929] x14: ffffff80019e9915 x13: ffffff80019e9913 x12: 00000000ffffffea
[    2.242276] x11: 00000000ffffefff x10: 0000000000000062 x9 : 00000000ffffffd0
[    2.246760] bcm63138_nand ff801800.nand-controller: timeout waiting for command 0x4
[    2.249623] x8 : 0000000000000073 x7 : ffffffc0815d37c0 x6 : 0000000000000075
[    2.257513] bcm63138_nand ff801800.nand-controller: intfc status c00000e0
[    2.264855] x5 : 0000000000000081 x4 : 0000000000000000 x3 : ffffff8001b61800
[    2.279193] x2 : ffffffc080b5d000 x1 : ffffff80020003a8 x0 : ffffff8002000398
[    2.286540] Call trace:
[    2.289048]  xhci_gen_setup+0x80/0x34c [xhci_hcd]

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2024-03-28 13:29:52 +01:00
Rafał Miłecki
4aff8d0d52 bcm4908: switch to the kernel 6.1
Tested on Netgear R8000P and TP-Link Archer C2300.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2024-03-28 13:29:52 +01:00
Rafał Miłecki
359be94f5e bcm4908: use DT to mark NAND controller WP pin as not connected
Use cleaner and more upstream-fit solution.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2024-03-28 13:29:52 +01:00
Robert Marko
fd58b1a8bc airoha: remove 5.15 support
Now that 6.1 is default, remove 5.15 support.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-03-28 13:06:43 +01:00
Robert Marko
cbc2664d1d airoha: default to kernel 6.1
6.1 has been present as testing for a while now, so default to it.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-03-28 13:06:43 +01:00