Fix broken onhub dtsi. The gmac node have a redundant phy-handle that
doesn't point to the swconfig phy node as they got dropped in the DSA
conversion. Drop these extra binding to restore correct compilation of
this subtarget.
Fixes: 337e36e0ef ("ipq806x: convert each device to DSA implementation")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fix copy-paste error in migrating NEC Aterm WG2600HP3 to new LED
implementation for the QCA8K switch. Correct define the missing
additional LED pin used for each port and fix wrong color for LED 2 for
each port. Also add the required function-enumerator as all 3 LED have
the same color and function.
Fixes: c707cff6c9 ("ipq806x: add LEDs definition for non-standard qca8k LEDs")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Extreme Networks AP3935i/e -
https://www.extremenetworks.com/support/documentation/access-points-ap3935i-e/
SoC: IPQ8068 QYY AT46279K45060I
RAM: NANYA 1527 NT5CC256M16DP-DI 515073W0EF 7 TW
FLASH: NOR - S25FL256S1 - 32MB
NAND - Macronix MX30UF4G28AB - 512MB
LAN: Atheros AR8035-A J5150WL 1515 CN - RGMII
LAN2: Atheros AR8033-AL1A SKCSR.AJ1 1444 China - SGMII
WLAN2: QCA9990 OVV FNPV209 K451406
WLAN5: QCA9990 OVV FNPV209 K451406
SERIAL: RS232 Port (115200 8n1) Cisco console cable and
4pin Serial Header | 3.3 | GND | RX | TX
MAC address for LAN1/LAN2/WLAN 2G/WLAN 5G in uboot env
* Installation via either RJ45 console or on-board 4 PIN header
Install Method
--------------
1) Setup TFTP server, and place
openwrt-ipq806x-generic-extreme_ap3935-initramfs-uImage image
in /srv/tftp or similar
2) Connect to console on router and connect ethernet port "LAN1" to
your LAN
3) Interupt the boot with any character
4) Login with admin/new2day for default password
(use reset/FactoryDefault if password needs to be reset)
5) Set serverip to TFTP IP: set serverip 192.168.1.2
6) Set ipaddr to another IP: set ipaddr 192.168.1.101
7) Make uboot ping something to activate eth0 on boot:
set bootcmd 'ping 192.168.1.1; run boot_flash'
saveenv
8) TFTP image to RAM:
tftpboot 0x42000000
openwrt-ipq806x-generic-extreme_ap3935i-initramfs-uImage
9) Boot image: bootm 0x42000000
In OpenWRT, "LAN1" is LAN, "LAN2" is WAN
10) SFTP openwrt-ipq806x-generic-extreme_ap3935-squashfs-nand-sysupgrade.bin
image to /tmp
11) sysupgrade /tmp/openwrt-*-nand-sysupgrade.bin
Signed-off-by: Glen Lee <g2lee@yahoo.com>
Add patch fixing regression from stmmac TX timer.
Refer to the single patch for extensive details on the problem.
This should restore original performance before 4.19 kernel.
Fixes: #11676
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add patch fixing regression from stmmac TX timer.
Refer to the single patch for extensive details on the problem.
This should restore original performance before 4.19 kernel.
Fixes: #11676
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add LEDs definition for devices that use a non-standard qca8k LEDs
configuration.
This is to restore original setup of the LED and be on par with swconfig
old configuration.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Enable and setup multi-cpu for qca8k switch for ipq806x based devices.
Rework each DTS to enable the secondary CPU port on QCA8K switch and
apply the required values originally set by the OEM in the old swconfig
node.
In original firmware the first CPU port was always assigned to the WAN
port and the secondary CPU port was assigned to the rest of the LAN
port. Follow this original implementation using an init.d script.
To setup the CPU port ip tools is required. Add additional default
package ip-tiny to correctly setup the CPU port.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop and move ASRock G10 preinit script to fix mac address to generic
board.d script and rework for consistency with other devices following a
similar implementation.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Convert each ipq806x device to DSA implementation using the qca8k
driver. Rework 02_network to follow the new naming scheme.
Update 01_leds to use netdev trigger with correct DSA port and drop
now unused switch trigger.
Currently secondary CPU is disabled and will be reneabled later.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
There's a typo in here: board_name is a function, not a variable. This
issue was pointed out on the OpenWrt forum.
Closes: #13409
Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
One of our SPI devices references this node, but we never enabled it.
This clutters up probe deferral logs.
(NB: this SPI device still doesn't have a real driver, so it's just here
for documentation and/or tinkering.)
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The qcom spm driver is currently broken for IPQ8064 OnHub devices on
kernel 6.1, such that it hangs the system when booting, much to the
consternation of users. This is especially bad as these devices don't
yet have a fully-supported release branch, and are still sometimes
landing on snapshot builds.
OnHub devices have their own kernel config, so it's not that wide of an
impact to disable this.
I haven't fully gotten to the bottom of this, but:
(a) The vendor kernel didn't have any SPM driver at all, and didn't
utilize cpuidle.
(b) The device tree has never included any (non-disabled) cpuidle
states, so even when this driver was present on 5.15 (last
known-working kernel), it didn't actually do anything -- it bailed
early, before ever doing any SPM initialization.
(c) Refactoring in Linux 5.16 [1] caused the SPM driver to be activated
unconditionally, including setting us into standby mode
(PM_SLEEP_MODE_STBY) by default.
Removing the one PM_SLEEP_MODE_STBY line from drivers/soc/qcom/spm.c
seems to fix the problem, but that isn't much different than simply
disabling the driver, so I go with that for now.
I also disable CONFIG_ARM_QCOM_SPM_CPUIDLE, becuase it 'select's
QCOM_SPM.
NB: it's possible there's some other deeper root cause involved in here.
For one, I notice that CPU hotplug (e.g., echo 0 >
/sys/devices/system/cpu/cpu1/online, echo 1 > ...) doesn't work right
either. Perhaps there's some mismatch on upstream Linux qcom-scm
behavior and the old boot firmware used for these systems? It wouldn't
be the first time, as we've had some similar incompatibilities on the
next generation of these devices, Google WiFi [2].
[1] Commit 60f3692b5f0b ("cpuidle: qcom_spm: Detach state machine from
main SPM handling")
[2] [RFC] qcom_scm: IPQ4019 firmware does not support atomic API?
https://lore.kernel.org/linux-arm-kernel/20200913201608.GA3162100@bDebian/
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Backport merged patch fixing broken hwspinlock due to missing regmap
config for SFPB MMIO implementation.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Manually rebased:
generic/hack-6.1/220-arm-gc_sections.patch
armsr/patches-6.1/221-armsr-disable_gc_sections_armv7.patch
All other patches automatically rebased.
Signed-off-by: John Audia <therealgraysky@proton.me>
In pushing and refreshing 6.1 pull request, dbac8e8819 ("ipq806x: 6.1:
copy patches, files and config from 5.15") wasn't correctly updated and
resulted in missing the dts for Netgear XR450. This caused compilation
error with Netgear R7800 or XR500 if testing kernel version was used.
Fix this by adding back the missing dts for Netgear XR450 from kernel
5.15.
Fixes: dbac8e8819 ("ipq806x: 6.1: copy patches, files and config from 5.15")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Move default cpufreq governor from ONDEMAND to PERFORMANCE. The temp
increase is just 2°C and Watt usage the change is minimal in the order
of additional millwatt. The SoC and krait in general looks to suffer for
some problem with cache scaling. To have better system stability, force
cpu freq and cache freq to the max value supported by the system. This
follows mvebu platform where cpufreq is broken and cause minimal
temp/watt increase.
User can still tweak the governor to ondemand using sysfs entry if
needed.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport initial LEDs hw control support. Currently this is limited to
only rx/tx and link events for the netdev trigger but the API got
accepted and the additional modes are working on and will be backported
later.
Refresh every patch and add the additional config flag for QCA8K new
LEDs support.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
commit 0c45ad41e1 changes ipq806x usb kmod name
from usb-phy-qcom-dwc3 to phy-qcom-ipq806x-usb, so
use new name.
Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
This allows loading modules with large memory requirements, recently needed
while testing on armvirt/32. Past forum discussions [1] and bug reports [2]
also raised this and the ipq806x target already set it in response [3].
Given this increases kernel image size by only ~1KB, is generally useful on
multi-platform kernels, and enabled by default on upstream arm32 Linux, add
it to the generic config.
The setting has similar utility on arm64, is a requirement for KASLR, and
already enabled on most OpenWrt aarch64 targets, so pull this into the
top-level generic config.
[1]: https://forum.openwrt.org/t/vmap-allocation-for-size-442368-failed-use-vmalloc-size-to-increase-size/34545/7
[2]: https://github.com/openwrt/openwrt/issues/8282
[3]: f81e148eb6 ("ipq806x: update 4.19 kernel config").
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Refresh dts for kernel 6.1 support.
Changes:
- nbg6817 drop amba node and reference directly sdcc1.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
With 6.1 lots have changed and the platform for Makefile.boot got
dropped. Replace the patch with a new version that is alligned to the
new implementation.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
should have been part of the ipq-wifi update.
Fixes: 8217f02a1c ("ipq-wifi: drop upstreamed board-2.bin")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The BDFs for the:
Aruba AP-365
Devolo Magic 2 WiFi next
Edgecore ECW5410
Edgecore OAP100
Extreme Networks WS-AP3915i
GL.iNet GL-A1300
GL.iNet GL-AP1300
GL.iNet GL-S1300
Linksys EA8300
Linksys WHW03v2
Nokia Wi4A AC400i
P&W R619AC
Pakedge WR-1
Qxwlan E2600AC C1
Sony NCP-HG100/Cellular
Teltonika RUTX10
ZTE MF18A
were upstreamed to the ath10k-firmware repository
and landed in linux-firmware.git.
Furthermore the BDFs for the:
8devices Habanero
8devices Jalapeno
Qxwlan E2600AC C2
have been updated.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
All targets are bumped to 5.15. Remove the old 5.10 patches, configs
and files using:
find target/linux -iname '*-5.10' -exec rm -r {} \;
Further, remove the 5.10 include.
Signed-off-by: Nick Hainke <vincent@systemli.org>
Drop arm override compile patch. The use is dubious and at times (2016)
it was never explained why this was required.
Krait CPU and Cortex-a15 may be similar but they have some intrinsic
difference. While very similar they differ a lot in additional feature
and also cache configuration.
Also these conflict with raid6 libraty compilation that use specific
workaround not compatible with cortex-a15 and produce compilation
warning.
Fix compilation warning:
cc1: error: switch '-mcpu=cortex-a15' conflicts with switch '-march=armv7-a+simd' [-Werror]
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fix compilation warning from mangle bootargs patch. Now that we flag
warning as error these cause compilation error.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fix following error when building 32bit arm targets with kmod-crypto-sha512
ERROR: module '/home/user/openwrt/build_dir/target-arm_xscale_musl_eabi/linux-kirkwood_generic/linux-5.15.109/arch/arm/crypto/sha512-arm.ko' is missing.
Signed-off-by: Lu jicong <jiconglu58@gmail.com>
