This patch adds support for the Edgecore ECW5410 indoor AP.
Specification:
- SoC: Qualcomm Atheros IPQ8068 ARMv7 2x Cortex A-15
- RAM: 256MB(225 usable) DDR3
- NOR Flash: 16MB SPI NOR
- NAND Flash: 128MB S34MS01G2 Parallel NAND
- Ethernet: 2 x 1G via 2x AR8033 PHY-s connected directly to GMAC2 and GMAC3 via SGMII (802.3af POE IN on eth0)
- USB: 1 x USB 3.0 SuperSpeed
- WLAN: 2x QCA9994 AC Wawe 2 (1x 2GHz bgn, 1x 5GHz acn)
- CC2540 BLE
- UART console on RJ45 next to ethernet ports exposed.
Its Cisco pin compatible, 115200 8n1 baud.
Installation instructions:
Through stock firmware or initramfs.
1.Connect to console
2. Login with root account, if password is unknown then interrupt the boot with f and reset it in failsafe.
3. Transfer factory image
4. Flash the image with ubiformat /dev/mtd1 -y -f <your factory image path>
This will replace the rootfs2 with OpenWrt, if you are currently running from rootfs2 then simply change /dev/mtd1 to /dev/mtd0
Note
Initramfs:
1. Connect to console
2. Transfer the image from TFTP server with tftpboot,
or by using DHCP advertised image with dhcp command.
3. bootm
4. Run ubiformat /dev/mtd1
You need to interrupt the bootloader after rebooting and run:
run altbootcmd
This will switch your active rootfs partition to one you wrote to and boot from it.
So if rootfs1 is active, then it will change it to rootfs2.
This will format the rootfs2 partition, if your active partition is 2 then simply change /dev/mtd1 with /dev/mtd0
If you dont format the partition you will be writing too, then sysupgrade will find existing UBI rootfs and kernel volumes and update those.
This will result in wrong ordering and OpenWrt will panic on boot.
5. Transfer sysupgrade image
6. Flash with sysupgrade -n.
Note that sysupgrade will write the image to rootfs partition that is not currently in use.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Changes:
- Update patches
- Update dts with new binding
Tx term offset dropped and replaced with a new compatible
Removed:
- 0071-5-PCI-qcom-Programming-the-PCIE-iATU-for-IPQ806x
Pci init does the same exact thing (was needed in older kernel version)
- 0071-7-pcie-Set-PCIE-MRRS-and-MPS-to-256B
Rejected upstream, can't find any reason to have this. No regression with
testing it on R7800.
Tested on R7800 (ipq8065), R7500 v2 ("ipq8064-v2")
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Tested-by: Paul Blazejowski <paulb@blazebox.homeip.net> [R7800]
[rebase and refresh]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The moves a few additional common nodes to the common DTSI files
for qcom-ipq8064-v2.0 and qcom-ipq8065 devices.
Remove a few redundant definitions on the way.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
- Replace dwc3 phy patch with upstream version
- Rework the dts to use the upstream bindings
- Update changed config flags
- Rename module to reflect config name
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[fix qcom,tx-deamp_3_5db typo, refresh patches, rename kmod]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Paul Blazejowski <paulb@blazebox.homeip.net> [R7800]
This uses upstream qcom-ipq8064-v1.0.dtsi and modifies it by patches
instead of keeping a local version. As a consequence:
- we use a part of the shared definitions there and update device
DTS files accordingly
- we move additional stuff from our local v1.0.dtsi to the patch
- we drop partitions, LEDs and keys from the file as we will
implement them differently anyway
Like with the previous patch, this follows the idea that a diff
from upstream might be easier to handle than a big file of our
own with different distribution pattern of properties.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Though a qcom-ipq8064.dtsi file exists upstream, we still do overwrite
it with a full version of our own in the ipq806x target. About half of
the contents of our file are upstream content, the other half are local
improvements.
To prevent us from having a lot of code maintained twice in parallel,
this adjusts the target to use the upstream qcom-ipq8064.dtsi. Our
local changes are arranged into three patches, the first pulling a
commit from upstream, the second doing a few small adjustments, and
the third adding all additional stuff.
This should get us the best of both worlds.
The property "ports-implemented" on sata@29000000 is moved to
2nd-level DTSI files as kernel defines it there as well.
While at, rename 080-ARM-dts-qcom-add-gpio-ranges-property.patch to
include the kernel version where it's added upstream.
Even though this might look more complicated in the first place,
the aim is to bring our files closer to upstream, so we can benefit
from changes directly and vice-versa. After all, this drop about
650 lines just copied from the upstream DTSI file.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Having looked at this again, it appears that only gsbi2_serial
is actually enabled for this device, so the entry in the broken
aliases node was correct.
Therefore, this needs to set its own serial0 instead of inheriting
"serial0 = &gsbi4_serial;" from DTSI. Do this with the correctly
named aliases node now.
Fixes: c83f7b6d21 ("ipq806x: fix aliases node name for Qualcomm
IPQ8064/DB149")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Kernel uses the label gsbiX_serial, so let's adjust our labels to
this naming scheme.
This is cosmetic, and actually only already existing gsbi4_serial
has been used at all.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This device uses a node incorrectly named "alias" instead of
"aliases" since it was introduced.
Remove it without replacement, as the definitions in it don't
seem to be required anyway:
The serial0 definition has never been effective anyway and this
would be the only device deviating from the common setting
"serial0 = &gsbi4_serial;" for ipq8064. (So, maybe the wrong
node prevented us from finding out about the wrong serial
definition?)
The mdio-gpio0 alias was supposed to be removed in d2a2eb7e48
anyway, the redundant definition in the alias node was just
overlooked back then.
Fixes: 0fd202f3e5 ("ipq806x: add db149 dts files")
Fixes: d2a2eb7e48 ("ipq806x: replace caf nss-gmac driver by upstream stmmac")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
At this moment Linksys EA8500 uses only eth0.
This patch change switch registers, which allow to use eth1 as lan
and eth0 as wan. The method work with similar Linksys EA7500V1
and it work with EA8500.
Suggested-by: Sungbo Eo <mans0n@gorani.run>
Tested-by: Brian Onn <brian.a.onn@gmail.com>
Tested-by: Adrian Panella <ianchi74@outlook.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
This patch adds support for the Linksys EA7500 V1 router.
Specification:
- CPU: Qualcomm IPQ8064
- RAM: 256MB
- Flash: NAND 128MB
- WiFi: QCA9982 an+ac + QCA9983 bgn
- Ethernet: 5 GBE Ports (WAN+ 4xLAN) (QCA8337)
- USB: 1x USB 3.0 1x USB2.0
- Serial console: RJ-45 115200 8n1 (1V8 Voltage level)
- 2 Buttons
- 1 LED
Known issues:
- Some devices won't flash via web gui
Installation:
- Newer stock images doesn't allow to install custom firmware.
- Please downgrade software to 1.1.2 version. Official firmware:
https://downloads.linksys.com/downloads/firmware/FW_EA7500_1.1.2.172843_prod.gpg.img
- Do it two times to downgrade all stored images.
- Apply factory image via web-gui.
Serial + TFTP method:
- downgrade to 1.1.2 two times
- connect ehternet and serial cable
- set ip address of tftp server to 192.168.1.254
- put openwrt factory image to tftp folder and rename it to macan.bin
- stop device while booting in u-boot
- run command: "run flashimg"
- run command: "setenv boot_part 1"
- run command "saveenv"
- reset
Back to stock:
- Please use old non-gpg image like this 1.1.2:
https://downloads.linksys.com/downloads/firmware/FW_EA7500_1.1.2.172843_prod.img
- ssh to router and copy image to tmp
- use sysupgrade -n -F
Tested by github users: @jack338c and @grzesiczek1
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
[removed i2c4_pins, mdio0_pins, nand_pins, rgmii2_pins from DTSI]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
All device DTS files in the target set the serial0 property to the
same value (*). So, let's move the definitions to the DTSI files.
That's also where the kernel defines it (qcom-ipq8064-v1.0.dtsi).
* The only exception is ipq8064-db149, which defines
"serial0 = &uart2;", but inside a block called "alias" instead of
"aliases". It must be assumed that this is broken anyway, so we
don't touch it here.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
All device DTS files in the target set the stdout-path to the same
value. So, let's move the definitions to the DTSI files.
That's also where the kernel defines it (qcom-ipq8064-v1.0.dtsi).
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
So far, the DTSI files on ipq806x had a linear inheritance:
qcom-ipq8064.dtsi
v
qcom-ipq8064-v1.0.dtsi
v
qcom-ipq8064-v2.0.dtsi
v
qcom-ipq8065.dtsi
This poses problems when one wants to set something that is specific
to an architecture closer to the top of the tree.
In this patch, we remove the chain-like inheritance and have all
other files derived from qcom-ipq8064.dtsi (changing this name to
something more generic is not possible due to upstream use).
The removal of inheritance will require a few entries to be copied
from qcom-ipq8064-v2.0.dtsi to qcom-ipq8065.dtsi. However, it also
opens an opportunity for some clean-up:
- Many definitions can be improved by just using the innermost labels.
- Instead of disabling the CPU_SPC node for ipq8065, it is now off by
default and enabled where needed.
- Instead of patching phy-tx0-term-offset into qcom-ipq8064.dtsi and
then having it changed for qcom-ipq8064-v2.0/qcom-ipq8065, just have
the appropriate settings done in the lower DTSI files directly.
- For the opp_table0 adjustments for ipq8065, just redefine what's
changed, but don't add all the untouched properties again.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
As almost same pinmux nodes are repeated in each device dts,
let's define them once in the ipq8064 dtsi and remove the rest.
* uart0_pins : Did not touch.
* i2c4_pins : This node seems to be not used at all in dts.
Added the most common form in the dtsi. Did not touch rpm_pins.
* spi_pins : The common mux node is already present in the dtsi.
Removed the duplicate nodes from dts.
* nand_pins : Moved the entire node.
* mdio0_pins : Moved the common mux node.
* rgmii2_pins: Moved the common mux node. "pins" property is overrided in ap161.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
As mdio0 is used in every dts move it to general ipq8064
dts and use label to set device specific definition.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Since this dtsi now have wrong definition in the upstream version,
include it to overwrite and remove any problem.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
