213748a9bcd9 system-linux: implement full device present state management for force-external devices
3abe1fc87151 system-linux: add retry for adding member devices to a bridge
Signed-off-by: Felix Fietkau <nbd@nbd.name>
You can flash via tftp recovery:
- serve tftp-recovery image as /tp_recovery.bin on 192.168.0.225/24
- connect to any ethernet port
- power on the device while holding the reset button
- wait at least 8 seconds before releasing reset button
Flashing via OEM web interface does not work.
LTE module does not support DHCP so it must be configured via QMI.
Hardware Specification (v4.0 EU):
- SoC: MT7628NN
- Flash: Winbond W25Q64JVS (8MiB)
- RAM: ESMT M14D5121632A (64MiB)
- Wireless: SoC platform only (2.4GHz b/g/n, 2x internal antenna)
- Ethernet: 1NIC (4x100M)
- WWAN: TP-LINK LTE MODULE (2x external detachable antenna)
- Power: DC 9V 0.85A
Signed-off-by: Filip Moc <lede@moc6.cz>
d4d78db uxc: also delete procd runtime state on 'delete'
e935c0c jail: add 'debug' extern variable to preload_seccomp
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
There already was an option for autoconfiguring IPv4 from QMI but this
was removed by commit 3b9b963e6e ("uqmi: always use DHCP for IPv4").
DHCP does not work on MR400 LTE module (in TL-MR6400 v4) so let's readd
support for IPv4 autoconf from QMI but this time allow to configure this
for IPv4 and IPv6 independently and keep DHCP default on IPv4.
Signed-off-by: Filip Moc <lede@moc6.cz>
Give possibility to wait forever the registration by setting timeout
option to 0.
No timeout can be useful if the interface starts whereas no network is
available, because at the end of timeout the interface will be stopped
and never restarted.
Signed-off-by: Thomas Richard <thomas.richard@kontron.com>
This reverts commit 9eb9943f82.
Building the 'modular' variant requires 'semodule_package' from
'selinux-python' to be installed on the buildhost.
Apart from that, this change also broke the monolithic refpolicy
'targeted' build.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Update mpc to 1.2.1
http://www.multiprecision.org/mpc/
Bug fixes:
Fix an incompatibility problem with GMP 6.0 and before.
Fix an intermediate overflow in asin.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
351d690f1a09 wireless: fix passing bridge name for vlan hotplug pass-through
c1c2728946b5 config: initialize bridge and bridge vlans before other devices
5e18d5b9ccb1 interface: do not force link-ext hotplug interfaces to present by default
4544f026bb09 bridge-vlan: add support for defining aliases for vlan ids
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The wcsnrtombs function in all musl libc versions up through 1.2.1 has
been found to have multiple bugs in handling of destination buffer
size when limiting the input character count, which can lead to
infinite loop with no forward progress (no overflow) or writing past
the end of the destination buffera.
This function is not used internally in musl and is not widely used,
but does appear in some applications. The non-input-limiting form
wcsrtombs is not affected.
All users of musl 1.2.1 and prior versions should apply the attached
patch, which replaces the overly complex and erroneous implementation.
The upcoming 1.2.2 release will adopt this new implementation.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
With this commit, the download script will try downloading source files
using the filename instead of the url-filename in case the previous
download attempt using the url-filename failed.
This is required, as the OpenWrt sources mirrors serve files using the
filename files might be renamed to after downloading. If the original
mirror for a file where url-filename and filename do not match goes
down, the download failed prior to this patch.
Further improvement can be done by performing this only for the
OpenWrt sources mirrors.
Signed-off-by: David Bauer <mail@david-bauer.net>
The ImageBuilder downloads pre-built packages and adds them to images.
This process uses `opkg` which has the capability to verify package list
signatures via `usign`, as enabled per default on running OpenWrt
devices.
Until now this was disabled for ImageBuilders because neither the `opkg`
keys nor the `opkg-add` script was present during first packagelist
update.
To harden the ImageBuilder against *drive-by-download-attacks* both keys
and verification script are added to the ImageBuilder allowing `opkg` to
verify downloaded package indices.
This commit adds `opkg-add` to the ImageBuilder scripts folder. The keys
folder is added to ImageBuilder $TOPDIR to have an obvious place for users to
store their own keys. The `option check_signature` is appended to the
repositories.conf file. All of the above only happens if the Buildbot
runs with the SIGNATURE_CHECK option.
The keys stored in the ImageBuilder keys/ are the same as included in
the openwrt-keyring package. To avoid the chicken-egg problem of
downloading and verifying a package, containing signing keys, the keys
are added during the ImageBuilder generation. They are same as in
shipped images (stored at `/etc/opkg/keys/`).
To allow a local package feed in which the user can add additional
packages, a local set of `usign` and `ucert` keys is generated, same as
building OpenWrt from source. The private key signs the local repository
inside the packages/ folder. The local public key is added to the keys/
folder to be considered by `opkg` when updating repositories. This way a
local package feed can be modified while requiring `opkg` to check
signatures for remote feed, making HTTPS optional.
The new option `ADD_LOCAL_KEY` allows to add the local key inside the
created images, adding the advantage that sysupgrades can validate the
ImageBuilders local key.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Commit 5d76065 moved the creation of the symvers directory to
include/kernel-build.mk. This is fine when building from scratch. But
when unpacking an SDK the directory doesn't exist and because the kernel
won't be built (again) this directory will not be created by the build
system, causing build failure if make tries to copy files into it.
This moves the creation of the symvers directory back into
include/kernel.mk so that the directory is created in any case.
Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
This patch adds support for the WiFi Pineapple Mark 7, a wireless
penetration testing tool.
Specifications:
* SoC: MediaTek MT7628 (580MHz)
* RAM: 256MiB (DDR2)
* Storage 1: 32MiB NOR (SPI)
* Storage 2: 2GB eMMC
* Wireless 1: 802.11b/g/n 2.4GHz (Built In)
* Wireless 2: 802.11b/g/n 2.4GHz (MT7601)
* Wireless 3: 802.11b/g/n 2.4GHz (MT7601)
* USB: 1x USB Type-A 2.0 Host Port
* Ethernet: 1x USB Type-C AX88772C Ethernet
* UART: 57600 8N1 on PCB
* Inputs: 1x Reset Button
* Outputs: 1x RGB LED
* FCCID: 2AA52MK7
Flash Instructions:
Original firmware is based on OpenWRT.
Use sysupgrade via SSH to flash.
Signed-off-by: Marc Egerton <foxtrot@realloc.me>
[pepe2k@gmail.com: set only required/used gpio groups to gpio function]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
New batches of the R36A board series might no longer keep separated
Ethernet MAC addresses stored in flash. Use same approach as on the
N2Q and calculate Ethernet MACs from WLAN one which is kept in ART.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
ALFA Network Pi-WiFi4 is a Qualcomm QCA9531 v2 based, high-power 802.11n
WiFi board in Raspberry Pi 3B shape, equipped with 1x FE and 4x USB 2.0.
Specifications:
- Qualcomm/Atheros QCA9531 v2
- 650/400/200 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16+ MB of flash (SPI NOR)
- 1x 10/100 Mbps Ethernet
- 2T2R 2.4 GHz Wi-Fi with Qorvo RFFM8228P FEM
- 2x IPEX/U.FL connectors on PCB
- 4x USB 2.0 Type-A
- Genesys Logic GL850G 4-port USB HUB
- USB power is controlled by GPIO
- 5x LED (3x on PCB, 2x in RJ45, 4x driven by GPIO)
- 1x button (reset)
- external h/w watchdog (EM6324QYSP5B, enabled by default)
- 1x micro USB Type-B for power and system console (Holtek HT42B534)
- UART and GPIO (8-pin, 1.27 mm pitch) header on PCB
Flash instruction:
You can use sysupgrade image directly in vendor firmware which is based
on LEDE/OpenWrt. Alternatively, you can use web recovery mode in U-Boot:
1. Configure PC with static IP 192.168.1.2/24.
2. Connect PC with one of RJ45 ports, press the reset button, power up
device, wait for first blink of all LEDs (indicates network setup),
then keep button for 3 following blinks and release it.
3. Open 192.168.1.1 address in your browser and upload sysupgrade image.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Kernel has separated the structs that are reported to be const in
checkpatch.pl into a file of its own, const_structs.checkpatch.
This file has been missing after the recent update of checkpatch.pl,
leading to the following message:
No structs that should be const will be found - file
'/data/openwrt/scripts/const_structs.checkpatch': No such file
or directory
This commit adds the relevant file from v5.10-rc4.
Fixes: 086ee09bbc ("scripts: Update checkpatch.pl to 2020-06-11")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The kernel expects changes to MAINTAINERS for all removed or added
files, printing warnings like:
WARNING: added, moved or deleted file(s), does MAINTAINERS need updating?
#828:
deleted file mode 100644
Since this does not apply to "our" files in OpenWrt repo, this
warning should be disabled.
This can be achieved easiest by setting $reported_maintainer_file
to 1. While this is a hack that tricks the script into believing
the proper MAINTAINERS changes have been made, it's the easiest
solution as it does not require to touch any other code.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The Xiaomi Mi Router 4A Gigabit model has a race condition on bootup
causing the SQUASHFS data errors to appear and create a bootloop
scenario.
Adding the m25p,fast-read property resolves this issue.
Suggested-by: David Bentham <db260179@gmail.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
CPU: Atheros AR9342 rev 3 SoC
RAM: 64 MB DDR2
Flash: 16 MB NOR SPI
WLAN 2.4GHz: Atheros AR9342 v3 (ath9k)
WLAN 5.0GHz: QCA988X
Ports: 2x GbE
Flashing procedure is identical to other ubnt devices.
https://openwrt.org/toh/ubiquiti/common
Flashing through factory firmware
1. Ensure firmware version v8.7.0 is installed.
Up/downgrade to this exact version.
2. Patch fwupdate.real binary using
`hexdump -Cv /bin/ubntbox | sed 's/14 40 fe 27/00 00 00 00/g' | \
hexdump -R > /tmp/fwupdate.real`
3. Make the patched fwupdate.real binary executable using
`chmod +x /tmp/fwupdate.real`
4. Copy the squashfs factory image to /tmp on the device
5. Flash OpenWrt using `/tmp/fwupdate.real -m <squashfs-factory image>`
6. Wait for the device to reboot
(copied from Ubiquiti NanoBeam AC and modified)
To keep it consistent, we will add the gen1 variant to
the nanobeam ac gen1.
Signed-off-by: Nick Hainke <vincent@systemli.org>
No special changes, just get in sync with recent code.
See here for the changelog:
https://valgrind.org/docs/manual/dist.news.html
The ipkg sizes changes as follows for mips 24kc :
3.15 : valgrind_3.15.0-2_mips_24kc.ipk 1450680
3.16.1 : valgrind_3.16.1-1_mips_24kc.ipk 1491954
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
No special changes, just get in sync with recent code.
See here for the changelog:
https://github.com/strace/strace/releases/tag/v5.9
The ipkg sizes changes as follows for mips 24kc :
5.8 : strace_5.8-1_mips_24kc.ipk 271195
5.9 : strace_5.9-1_mips_24kc.ipk 278352
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
No special changes, just get in sync with recent code.
See here for the changelog:
http://software.es.net/iperf/news.html#iperf-3-9-released
The ipkg sizes changes as follows for mips 24kc :
3.7 : iperf3_3.7-1_mips_24kc.ipk 39675
3.9 : iperf3_3.9-1_mips_24kc.ipk 41586
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Avoid needlessly breaking old initscripts that set EXTRA_COMMANDS. This
will aid in debugging (as it simplifies reverting to an older version of
a package) and unbreaks third-party feeds (and packages that maintain
their OpenWrt initscripts as part of the software's repo instead of the
OpenWrt feed like fastd).
Without this, initscripts that set EXTRA_COMMANDS become completely
unusable, as all default commands like start/stop cease working.
Fixes: 1a69f50dc6 ("base-files: fix rc.common help alignment")
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
This sets the validity interval for the BSS transition candidate
list to the same value as the disassociation timer.
Currently the value is always 0, which is the specification states is a
reserved value. Also, wpa_supplicant and from the looks of it some
Android implementations will outright ignore the candidate list in this
case.
Signed-off-by: David Bauer <mail@david-bauer.net>
* Add support for passing airtime_sta_weight into hostapd configuration.
* Since that commit it is possible to configure station weights. Set higher
value for larger airtime share, lower for smaller share.
I have tested this functionality by modyfing /etc/config/wireless to:
config wifi-device 'radio0'
...
option airtime_mode '1'
config wifi-iface 'default_radio0'
...
list airtime_sta_weight '01:02:03:04:05:06 1024'
Now, when the station associates with the access point it has been assigned
a higher weight value.
root@OpenWrt:~# cat /sys/kernel/debug/ieee80211/phy0/netdev\:wlan0/stations/01\:02\:03\:04\:05\:06/airtime
RX: 12656 us
TX: 10617 us
Weight: 1024
Deficit: VO: -2075 us VI: 256 us BE: -206 us BK: 256 us
[MAC address has been changed into a dummy one.]
Signed-off-by: Dobroslaw Kijowski <dobo90@gmail.com>
airtime_mode is always parsed as an empty string since it hasn't been
added into hostapd_common_add_device_config function.
Fixes: e289f183 ("hostapd: add support for per-BSS airtime configuration")
Signed-off-by: Dobroslaw Kijowski <dobo90@gmail.com>
This adds a new get_status method to a hostapd interface, which
provides information about the current interface status.
Signed-off-by: David Bauer <mail@david-bauer.net>
This adds information from mac80211 to hostapd get_client ubus function.
This way, TX as well as RX status information as well as the signal can
be determined.
Signed-off-by: David Bauer <mail@david-bauer.net>
procd-seccomp switched to OCI-compliant seccomp parser instead of our
(legacy, OpenWrt-specific) format. Convert ruleset to new format.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
