This updates uboot-envtools with the updated names from ramips
target.
Fixes: 6d4382711a ("ramips: use full names for Xiaomi Mi Router devices")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This commit adds support for Xiaomi's Mi Router 4C device.
Specifications:
- CPU: MediaTek MT7628AN (580MHz)
- Flash: 16MB
- RAM: 64MB DDR2
- 2.4 GHz: IEEE 802.11b/g/n with Integrated LNA and PA
- Antennas: 4x external single band antennas
- WAN: 1x 10/100M
- LAN: 2x 10/100M
- LEDs: 2x yellow/blue. Programmable (labelled as power on case)
- Non-programmable (shows WAN activity)
- Button: Reset
How to install:
1- Use OpenWRTInvasion to gain telnet and ftp access.
2- Push openwrt firmware to /tmp/ using ftp.
3- Connect to router using telnet. (IP: 192.168.31.1 -
Username: root - No password)
4- Use command "mtd -r write /tmp/firmware.bin OS1" to flash into
the router..
5- It takes around 2 minutes. After that router will restart itself
to OpenWrt.
Signed-off-by: Ataberk Özen <ataberkozen123@gmail.com>
[wrap commit message, bump PKG_RELEASE for uboot-envtools, remove
dts-v1 from DTS, fix LED labels]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
FCC ID: A8J-EAP300A
Engenius EAP300 v2 is an indoor wireless access point with a
100/10-BaseT ethernet port, 2.4 GHz wireless, internal antennas,
and 802.3af PoE.
**Specification:**
- AR9341
- 40 MHz reference clock
- 16 MB FLASH MX25L12845EMI-10G
- 64 MB RAM
- UART at J1 (populated)
- Ethernet port with POE
- internal antennas
- 3 LEDs, 1 button (power, eth, wlan) (reset)
**MAC addresses:**
phy0 *:d3 art 0x1002 (label)
eth0 *:d4 art 0x0/0x6
**Installation:**
- if you get Failsafe Mode from failed flash:
only use it to flash Original firmware from Engenius
or risk kernel loop or halt which requires serial cable
Method 1: Firmware upgrade page:
OEM webpage at 192.168.1.1
username and password "admin"
Navigate to "Firmware" page from left pane
Click Browse and select the factory.bin image
Upload and verify checksum
Click Continue to confirm and wait 3 minutes
Method 2: Serial to load Failsafe webpage:
After connecting to serial console and rebooting...
Interrupt uboot with any key pressed rapidly
execute `run failsafe_boot` OR `bootm 0x9fdf0000`
wait a minute
connect to ethernet and navigate to
"192.168.1.1/index.htm"
Select the factory.bin image and upload
wait about 3 minutes
**Return to OEM:**
If you have a serial cable, see Serial Failsafe instructions
*DISCLAIMER*
The Failsafe image is unique to Engenius boards.
If the failsafe image is missing or damaged this will not work
DO NOT downgrade to ar71xx this way, can cause kernel loop or halt
The easiest way to return to the OEM software is the Failsafe image
If you dont have a serial cable, you can ssh into openwrt and run
`mtd -r erase fakeroot`
Wait 3 minutes
connect to ethernet and navigate to 192.168.1.1/index.htm
select OEM firmware image from Engenius and click upgrade
**TFTP recovery** (unstable / not reliable):
rename initramfs to 'vmlinux-art-ramdisk'
make available on TFTP server at 192.168.1.101
power board while holding or pressing reset button repeatedly
NOTE: for some Engenius boards TFTP is not reliable
try setting MTU to 600 and try many times
**Format of OEM firmware image:**
The OEM software of EAP300 v2 is a heavily modified version
of Openwrt Kamikaze. One of the many modifications
is to the sysupgrade program. Image verification is performed
simply by the successful ungzip and untar of the supplied file
and name check and header verification of the resulting contents.
To form a factory.bin that is accepted by OEM Openwrt build,
the kernel and rootfs must have specific names
and begin with the respective headers (uImage, squashfs).
Then the files must be tarballed and gzipped.
The resulting binary is actually a tar.gz file in disguise.
This can be verified by using binwalk on the OEM firmware images,
ungzipping then untaring.
The OEM upgrade script is at /etc/fwupgrade.sh.
OKLI kernel loader is required because the OEM software
expects the kernel size to be no greater than 1536k
and otherwise the factory.bin upgrade procedure would
overwrite part of the kernel when writing rootfs.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
[clarify MAC address section, bump PKG_RELEASE for uboot-envtools]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch adds support for Globalscale ESPRESSObin-Ultra. Device uses
the same Armada-3720 SoC with extended hardware support.
- SoC: Armada-3720
- RAM: 1 GB DDR4
- Flash: 4MB SPI NOR (mx25u3235f) + 8 GB eMMC
- Ethernet: Topaz 6341 88e6341 (4x GB LAN + 1x WAN with 30W PoE)
- WiFI: 2x2 802.11ac Wi-Fi marvell (88w8997 PCIe+USB)
- 1x USB 2.0 port
- 1x USB 3.0 port
- 1x microSD slot
- 1x mini-PCIe slot (USB [with nano-sim slot])
- 1x mini-USB debug UART
- 1x RTC Clock and battery
- 1x reset button
- 1x power button
- 4x LED (RGBY)
- Optional 1x M.2 2280 slot
** Installation **
Copy dtb from build_dir to bin/ and run tftpserver there:
$ cp ./build_dir/target-aarch64_cortex-a53_musl/linux-mvebu_cortexa53/
linux-5.4.65/arch/arm64/boot/dts/marvell/armada-3720-espressobin-ultra.dtb
bin/targets/mvebu/cortexa53/
$ in.tftpd -L -s bin/targets/mvebu/cortexa53/
Connect to the device UART via microUSB port on the back side and power on the device.
Power on the device and hit any key to stop the autoboot.
Set serverip (host IP) and ipaddr (any free IP address on the same subnet), e.g:
$ setenv serverip 192.168.1.10 # Host
$ setenv ipaddr 192.168.1.15 # Device
Ping server to confirm network is working:
$ ping $serverip
Using neta@30000 device
host 192.168.1.15 is alive
Tftpboot the firmware:
$ tftpboot $kernel_addr_r openwrt-mvebu-cortexa53-globalscale_espressobin-ultra-initramfs-kernel.bin
$ tftpboot $fdt_addr_r armada-3720-espressobin-ultra.dtb
Set the console and boot the image:
$ setenv bootargs $console
$ booti $kernel_addr_r - $fdt_addr_r
Once the initramfs is booted, transfer openwrt-mvebu-cortexa53-globalscale_espressobin-ultra-squashfs-sdcard.img.gz
to /tmp dir on the device.
Gunzip and dd the image:
$ gunzip /tmp/openwrt-mvebu-cortexa53-globalscale_espressobin-ultra-squashfs-sdcard.img.gz
$ dd if=/tmp/openwrt-mvebu-cortexa53-globalscale_espressobin-ultra-squashfs-sdcard.img of=/dev/mmcblk0 && sync
Reboot the device.
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
Add support for the following devices:
- Xiaomi Mi Wi-Fi Router 3G v2
- Xiaomi Mi Router 4A Gigabit Edition
Signed-off-by: Antonis Kanouras <antonis@metadosis.eu>
[add explicit case for 4A, bump PKG_RELEASE,
improve commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
On the Turris Omnia 2019, u-boot environment is located at 0xF0000, instead
of 0xC0000. The switch happened with u-boot-omnia package version 2019-04-2
(May 10, 2019).
Check the installed u-boot release, and set the default accordingly.
Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
[bump PKG_RELEASE, use lower case for hex offset]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The RAVPower RP-WD03 is a battery powered router, with an Ethernet and
USB port. Due due a limitation in the vendor supplied U-Boot bootloader,
we cannot exceed a 1.5 MB kernel size, as is the case with recent builds
(i.e. post v19.07). This breaks both factory and sysupgrade images.
To address this, use the lzma loader (loader-okli) to work around this
limitation.
The improvements here also address the "misplaced" U-Boot environment
partition, which is located between the kernel and rootfs in the stock
image / implementation. This is addressed by making use of mtd-concat,
maximizing space available in the booted image.
This will make sysupgrade from earlier versions impossible.
Changes are based on the recently supported HooToo HT-TM05, as the
hardware is almost identical (except for RAM size) and is from the same
vendor (SunValley). While at it, also change the SPI frequency
accordingly.
Installation:
- Download the needed OpenWrt install files, place them in the root
of a clean TFTP server running on your computer. Rename the files as,
- openwrt-ramips-mt7620-ravpower_rp-wd03-squashfs-kernel.bin => kernel
- openwrt-ramips-mt7620-ravpower_rp-wd03-squashfs-rootfs.bin => rootfs
- Plug the router into your computer via Ethernet
- Set your computer to use 10.10.10.254 as its IP address
- With your router shut down, hold down the power button until the first
white LED lights up.
- Push and hold the reset button and release the power button. Continue
holding the reset button for 30 seconds or until it begins searching
for files on your TFTP server, whichever comes first.
- The router (10.10.10.128) will look for your computer at 10.10.10.254
and install the two files. Once it has finished installation, it will
automatically reboot and start up OpenWrt.
- Set your computer to use DHCP for its IP address
Notes:
- U-Boot environment can be modified, u-boot-env is preserved on initial
install or sysupgrade
- mtd-concat functionality is included, to leave a "hole" for u-boot-env,
combining the OEM kernel and rootfs partitions
Most of the changes in this commit are the work of Russell Morris (as
credited below), I only wrapped them up and added compat-version.
Thanks to @mpratt14 and @xabolcs for their help getting the lzma loader
to work!
Fixes: 5ef79af4f8 ("ramips: add support for Ravpower WD03")
Suggested-by: Russell Morris <rmorris@rkmorris.us>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The HooToo HT-TM05 is a battery powered router, with an Ethernet and USB port.
Vendor U-Boot limited to 1.5 MB kernel size, so use lzma loader (loader-okli).
Specifications:
SOC: MediaTek MT7620N
BATTERY: 10400mAh
WLAN: 802.11bgn
LAN: 1x 10/100 Mbps Ethernet
USB: 1x USB 2.0 (Type-A)
RAM: 64 MB
FLASH: GigaDevice GD25Q64, Serial 8 MB Flash, clocked at 50 MHz
Flash itself specified to 80 MHz, but speed limited by mt7620 SPI
fast-read enabled (m25p)
LED: Status LED (blue after boot, green with WiFi traffic
4 leds to indicate power level of the battery (unable to control)
INPUT: Power, reset button
MAC assignment based on vendor firmware:
2.4 GHz *:b4 (factory 0x04)
LAN/label *:b4 (factory 0x28)
WAN *:b5 (factory 0x2e)
Tested and working:
- Ethernet
- 2.4 GHz WiFi (Correct MAC-address)
- Installation from TFTP (recovery)
- OpenWRT sysupgrade (Preserving and non-preserving), through the usual
ways: command line and LuCI
- LEDs (except as noted above)
- Button (reset)
- I2C, which is needed for reading battery charge status and level
- U-Boot environment / variables (from U-Boot, and OpenWrt)
Installation:
- Download the needed OpenWrt install files, place them in the root
of a clean TFTP server running on your computer. Rename the files as,
- ramips-mt7620-hootoo_tm05-squashfs-kernel.bin => kernel
- ramips-mt7620-hootoo_tm05-squashfs-rootfs.bin => rootfs
- Plug the router into your computer via Ethernet
- Set your computer to use 10.10.10.254 as its IP address
- With your router shut down, hold down the power button until the first
white LED lights up.
- Push and hold the reset button and release the power button. Continue
holding the reset button for 30 seconds or until it begins searching
for files on your TFTP server, whichever comes first.
- The router (10.10.10.128) will look for your computer at 10.10.10.254
and install the two files. Once it has finished installation, it will
automatically reboot and start up OpenWrt.
- Set your computer to use DHCP for its IP address
Notes:
- U-Boot environment can be modified, u-boot-env is preserved on initial
install or sysupgrade
- mtd-concat functionality is included, to leave a "hole" for u-boot-env,
combining the OEM kernel and rootfs partitions
I would like to thank @mpratt14 and @xabolcs for their help getting the
lzma loader to work!
Signed-off-by: Russell Morris <rmorris@rkmorris.us>
[drop changes in image/Makefile, fix indent and PKG_RELEASE in
uboot-envtools, fix LOADER_FLASH_OFFS, minor commit message facelift,
add COMPILE to Device/Default]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
In the rare event a pre-populated fw_env.config exists in the rootfs prior
to firstboot, calling fw_setenv after the system has initialised will
annihilate the devices environment due to two identical lines in
fw_env.config.
Check for existence prior to blind appendage.
Signed-off-by: Imran Khan <gururug@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[daniel@makrotopia.org: fixed patch format, improved grep, cosmetics]
Forward the OpenWrt TARGET_LDFLAGS to the linker of the fw_printenv tool.
In addition also use the more standard make invocation script.
With this change the fw_printenv tool is built with PIE and Full RELRO
support when activated globally in OpenWrt.
Signed-off-by: Hauke Mehrtens <hauke.mehrtens@intel.com>
After changing board names to DT compat string, we also need to
adjust the script which generates uboot-env configuration files.
Fixes: e880a30549 ("mxs: use generic sysinfo board detection")
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Currently, the build system uses an openwrt mirror which does not currently
work and FTP can be unreliable under several circumstances. This change
implicitly allows using all the mirrors to download.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Several changes has been made:
+ AES support has been removed by
upstream commit c6831c7 (2017-11-14)
[remove patch "200-fw_env_no_aes.patch"]
+ Support for UBI volumes has beed added by
upstream commit 34255b9 (2017-11-15)
[remove patch "300-support-env-in-ubivol-chardev.patch"]
+ A command line argument has beed added ("-c") to manually indicate
the location of the environment configuration file
Also, patch "400-u-boot-2015.10-stdint.patch" is no longer
necessary, and the config option to enable UBI support has
been removed.
Size comparisons:
fw_printenv size:
Target Before After
ar71xx 15,189 bytes 18,133 bytes (+2,944 bytes)
ipq40xx 20,873 bytes 20,987 bytes (+114 bytes)
mvebu 20,881 bytes 20,991 bytes (+110 bytes)
ramips 15,128 bytes 18,072 bytes (+2,944 bytes)
OPKG package size:
Target Before After
ar71xx 11,309 bytes 12,875 bytes (+1,566 bytes)
ipq40xx 11,772 bytes 13,299 bytes (+1,527 bytes)
mvebu 11,609 bytes 13,114 bytes (+1,505 bytes)
ramips 10,975 bytes 12,503 bytes (+1,528 bytes)
Compile tested: ipq40xx (musl, glibc, gcc5-musl), ar71xx, mvebu, ramips
Run tested: ipq40xx (ASUS RT-AC58U)
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
The Pistachio target is a MIPS interaptiv based SoC developed by
Imagination Technologies. It includes blocks for i2c, spi, audio,
usb and WiFi.
This also adds the base support for the 'Creator Ci40 (marduk)'
device which uses the Pistachio SoC to create an IoT hub by
including Bluetooth, WiFi and 6lowpan on one board. Additionally 2x
Mikrobus ports are available to expand with further RF technologies
or add sensors. You can find out more here http://creatordev.io.
Note, this commit is just the initial board support hence the
following are not expected to work yet:
* WiFi
* Bluetooth
* 6lowpan
* Audio
* Mikrobus uarts, user leds (clock dependency of 6lowpan chip)
The aim of this commit is to essentially have the same level of
support that currently exists in the mainline kernel.
Signed-off-by: Abhijit Mahajani <Abhijit.Mahajani@imgtec.com>
Signed-off-by: Francois Berder <francois.berder@imgtec.com>
Signed-off-by: Ian Pozella <Ian.Pozella@imgtec.com>
Signed-off-by: Mayank Sirotiya <Mayank.Sirotiya@imgtec.com>
Signed-off-by: Sean Kelly <Sean.Kelly@imgtec.com>
Note, that licensing stuff is a nightmare: many packages does not clearly
state their licenses, and often multiple source files are simply copied
together - each with different licensing information in the file headers.
I tried hard to ensure, that the license information extracted into the OpenWRT's
makefiles fit the "spirit" of the packages, e.g. such small packages which
come without a dedicated source archive "inherites" the OpenWRT's own license
in my opinion.
However, I can not garantee that I always picked the correct information
and/or did not miss license information.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
SVN-Revision: 43155
On UBI enabled devices, U-Boot might store it's environment on
UBI volume(s). Support this in uboot-envtools, so fw_setenv and
fw_printenv can work on these platforms.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 40929
