QCA956x is configured like AR934x, not like the older chips.
Should fix ethernet hangs when using the WAN port without SGMII
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Prior to commit 1496b95a0 ("x86: clean up default grub baudrate
settings") we had three different baud rates for the Geode targets:
19200 for net5501, 38400 for alix2, and 115200 for Geos.
It doesn't seem that there's a very good reason for varying from our
default 115200 baud, so let's make the Geode target do that instead.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This makes the Geode images actually useful again. The Geos profile
should include the relevant hardware for that board, and the Default
profile adds the via-rhine adapter which seems to have been present in
the net5501 and alix targets killed in commit 9e0759ea26 ("x86: merge
all geode based subtargets into one").
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Lima is a module for the (IoE) internet of everything applications,
based on Qualcomm/Atheros QCA4531.
Specification:
- 650/600/216 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 32 MB of FLASH
- 2T2R 2.4 GHz
- 2x 10/100 Mbps Ethernet
- USB 2.0 Host
- PCIe
- UART for serial console
- 14x GPIO
Flash instruction:
1. Download lede-ar71xx-generic-lima-squashfs-sysupgrade.bin
and rename it to 8dev_recovery.bin
2. Binary file copy to USB stick and plug into slot USB
3. Press S2 (reset) button
4. Press and hold the S1 button by 5 seconds
5. Wait ~40 seconds to complete recovery
Tested on:
- Lima development kit
Signed-off-by: Karol Dudek <karoiz@sli.pl>
commit 33b72b8e0f
"ar8216: adjust ATU flushing in case of link changes"
introduced portwise flushing on link down events. Now the ARL table could
be in a chaotic state after boot where ar8xxx_sw_get_arl_table looped
forever (depending on the entries collected while booting).
Signed-off-by: Günther Kelleter <guenther.kelleter@devolo.de>
GPIO18 and GPIO19 on OMEGA2(+) should be GPIO mode, enable PWM lead to a conflict
[ 0.290633] rt2880-pinmux pinctrl: pin io18 already requested by pinctrl; cannot claim for 10005000.pwm
[ 0.299722] rt2880-pinmux pinctrl: pin-18 (10005000.pwm) status -22
[ 0.305729] rt2880-pinmux pinctrl: could not request pin 18 (io18) from group pwm0 on device rt2880-pinmux
[ 0.315131] mtk-pwm 10005000.pwm: Error applying setting, reverse things back
Keep PWM disabled.
Signed-off-by: Furong Xu <xfr@outlook.com>
Removing redundant spaces from the name of the option. Without fix:
root@LEDE:~# opkg install ugps
Installing ugps (2016-10-24-32a6b2b7-1) to root...
Downloading http://downloads.lede-project.org/releases/17.01-SNAPSHOT/packages/mips_24kc/base/ugps_2016-10-24-32a6b2b7-1_mips_24kc.ipk
Configuring ugps.
uci: Parse error (invalid character in name field) at line 3, byte 23
uci: Parse error (invalid character in name field) at line 3, byte 23
sh: out of range
root@LEDE:~# uci show gps
uci: Parse error (invalid character in name field) at line 3, byte 23
With this fix:
root@LEDE:~# uci show gps
gps.@gps[0]=gps
gps.@gps[0].tty='ttyACM0'
gps.@gps[0].adjust_time='1'
Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
- Check for changes in toolchain/ only
- Only replace the stamp file if it was changed
- Fix dependencies for staging dir prepare
- Move the stamp file to TOOLCHAIN_DIR
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The Asus WL-500W buttons are active high,
but the software treats them as active low.
Fix the inverted logic.
Signed-off-by: Mirko Parthey <mirko.parthey@web.de>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
BCM4704 SoC has only USB 1.1 core:
ssb: Core 3 found: USB 1.1 Hostdev (cc 0x808, rev 0x03, vendor 0x4243)
but this device actually comes with two USB 2.0 ports.
It appears embedded controller isn't used but instead there are two PCI
attached controllers (next to the BCM4321 wireless card):
1106:3038 VT82xx/62xx UHCI USB 1.1 Controller
1106:3104 USB 2.0
Choose a set of USB drivers which actually support this hardware.
Signed-off-by: Mirko Parthey <mirko.parthey@web.de>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
When memory is tight, modules may need to be loaded into vmalloc()
space. The code then has to generate jump trampolines which enable
relocations between vmalloc space and physical address space.
The code had a bug that was freeing these trampolines even when the
module was successfully loaded.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This update includes numerous small fixes for:
1) Interfaces setup
2) Packets parsing
3) Sending replies
Without this there were multiple problems with exchanging information
between (u)mdns and other implementations (including (u)mdns as well).
This also follows project rename to umdns which was required to avoid
confusion with Apple's mdnsd from mDNSResponder project.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The cAP 2nD, mAP 2nD and wAP 2nD apparently all share the same QCA953x/SPI-NOR
platform.
This patch adds preliminary kernel support based on init data used in
Mikrotik's linux-3.3.5 kernel patch. Since this is totally experimental and
untested, the necessary glue in base-files has not been added, the code is
provided as a starting point in case somebody with that hardware wants to help
getting it supported.
The cAP lite (cAPL 2nD) should also be supported once it is determined whether
or not it uses the same board identifier as the mAP lite.
Code has been successfully built and has no side effect (no impact on already
supported devices).
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
This patch adds support for the MikroTik RouterBOARD hEX lite
https://routerboard.com/RB750r2
Specifications:
- SoC: Qualcomm QCA9531 (850MHz)
- RAM: 64MB
- Storage: 16MB NOR SPI flash
- Ethernet: 5x100M (1 PoE in)
This ethernet router is based on the same platform as the hEX PoE lite (it
shares the same board identifier), but has no USB and no PoE out.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
This patch adds support for the MikroTik RouterBOARD hEX PoE lite
https://routerboard.com/RB750UPr2
Specifications:
- SoC: Qualcomm QCA9531 (650MHz)
- RAM: 64MB
- Storage: 16MB NOR SPI flash
- Ethernet: 5x100M (1 PoE in, 1 PoE out)
- USB: Type A
This ethernet router is based on the same platform as the wireless router hAP.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
This patch implements support for the hAP lite in mach-rbspi.c
hAP lite was supported via mach-rb941.c, so this file is removed
as well as the corresponding build bits.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
This patch adds support for the MikroTik RouterBOARD mAP lite
https://routerboard.com/RBmAPL-2nD
Specifications:
- SoC: Qualcomm QCA9533 (650MHz)
- RAM: 64MB
- Storage: 16MB NOR SPI flash
- Wireless: builtin QCA9533, 2x2:2
- Ethernet: 1x100M
This is another 16M SPI NOR mikrotik device. The machine file is named
mach-rbspi.c because I plan to add support for several of the other spi-based
RouterBOARD devices in subsequent patches: they share most of the hardware
and thus the same codebase.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
Implement a new flag "-f" for the feeds update command which causes the
script to fall back to a more agressive git update strategy in case there
are locally modified files in the feeds directory.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
5f91241 procd: add cancel_timeout on rc scripts when a runtime_timeout is specified
961dc69 procd: stop service using SIGKILL if SIGTERM failed to do so
Signed-off-by: John Crispin <john@phrozen.org>
Default trigger action timeout was added to procd.sh in commit f88e3a4c0
(procd: add default timeout for reload trigger actions)
However, the timeout value was not placed under the correct JSON-script
array nesting level and thus did not apply.
To fix this and make the timeout actually apply to the reload triggers,
we place it in the correct scope, that is the per-trigger array.
Fixes: f88e3a4c0a
Signed-off-by: Denis Osvald <denis.osvald@sartura.hr>
Some boards were apparently forgotten when ralink,portmap was renamed
to mediatek,portmap -- probably because they used the long obsolete
ralink,port-map attribute.
If this commit breaks ethernet wan/lan assignment, this is because
the port-map attribute wasn't actually parsed, you'll have to replace
"wllll" by "llllw" in the dts file belonging to that board (and send
a patch doing that!)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This adds the default LED and network settings for the PC Engines APU2
when running under the x86 target.
[dwmw2: Change Ethernet port setup]
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Based on a patch from Chris Blake <chrisrblake93@gmail.com>, except let's
do it by using the LED configuration instead of hard-coding it for each
board type. And try using /bin/board_detect to do the default behaviour,
on the first boot where the config hasn't yet been generated.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This change moves the files in 657418d to the root of the x86 target.
This is done in preperation for adding more devices under other
subtargets.
CC: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
The DWR-512 embeds the hw slic device si3210. This device have the IRQ line
attached to the gpio1. This patch export the gpio1 with proper name and
parameters to the sysfs.
Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
this caused
'mv: can't rename '/mnt/sysupgrade.tgz': No such file or directory'
when running sysupgrade -n
Signed-off-by: John Crispin <john@phrozen.org>
This can be used to tweak the buildbot behavior without having to change
buildbot's configuration.
It will also allow us to add more aggressive clean steps (e.g. on
toolchain changes), which would break developers' workflows if enable
by default.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
