Using the arrow keys to navigate the U-Boot menu often leads to being
dropped into the U-Boot shell unexpectedly.
This can be prevented in most cases by improving the logic to detect the
arrow key ESC sequence and only reprinting the menu if actually needed.
Also enable CONFIG_SERIAL_RX_BUFFER for all boards as it helps preventing
the remaining cases.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Building uboot-mediatek fails with GCC-14, uboot v2024.10 and
CONFIG_SYS_NONCACHED_MEMORY defined with error:
cmd/cache.c: In function 'do_dcache':
cmd/cache.c:57:25: error: implicit declaration of function
'noncached_set_region' [-Wimplicit-function-declaration]
This is caused by upstream commit 7d6cee2cd0e2e2507aca1e3a6fe0e2cb241a116e
("cmd: cache: Remove weak functions") as this removes weak functions in
favor of arch-specific definitions.
This patch adds the function prototype for `noncached_set_region` to
arch-specific header for ARM. It also adds an include in cmd/cache.c to
make the function available there.
Fixes: #16697
Fixes: f8c22c9bff ("uboot-mediatek: update to U-Boot 2024.10")
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
[@dangowrt refreshed patch]
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add u-boot support based on the kernel dts introduced in d1016446 and
the GL-MT6000 u-boot support in fe10f974.
The pcie-mediatek-gen3 kernel driver doesn't like hotplug, so to work in
PCIe mode, the 5G modem on this device needs to be switched on by u-boot
before starting the kernel. Include an init_modem step in the boot_system
action to set the relevant gpios. (The factory bootloader does the same,
using Mediatek SDK-specific gpio_power_clr and gpio_pull_up.)
Ideally the modem would be started using gpio-hog in the device tree, but
this will need to wait until mediatek gpio-hog support is fixed upstream:
https://lore.kernel.org/u-boot/6ef2583e85eea60560d7776377d662779e7c44e5.1722419839.git.chris@arachsys.com/
The bootloader can be replaced using the built-in web interface of the
factory bootloader. Hold the reset button for five seconds while powering
on the device and it will boot into a recovery http server.
http://192.168.1.1/uboot.html and http://192.168.1.1/bl2.html can then
be used to upload openwrt-mediatek-filogic-glinet_gl-x3000-bl31-uboot.fip
and openwrt-mediatek-filogic-glinet_gl-x3000-preloader.bin respectively.
Alternatively, from a root shell on the running system, unlock the boot
partition with
echo 0 >/sys/block/mmcblk0boot0/force_ro
then write openwrt-mediatek-filogic-glinet_gl-x3000-bl31-uboot.fip to
/dev/mmcblk0p4 and openwrt-mediatek-filogic-glinet_gl-x3000-preloader.bin
to /dev/mmcblk0boot0.
Signed-off-by: Chris Webb <chris@arachsys.com>
Link: https://github.com/openwrt/openwrt/pull/15645
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Same as TP-Link TL-XDR608x, this router comes with locked vendor
loader. Add U-Boot build for replacement loader for this device.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/15930
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hardware specification:
SoC: MediaTek MT7981B 2x A53
Flash: 128 MB SPI-NAND
RAM: 256MB
Ethernet: 4x 10/100/1000 Mbps
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset, Mesh
Power: DC 12V 1A
Gain telnet access:
1. Login into web interface, and download the configuration.
2. Decode and uncompress the configuration:
* Enter fakeroot if you are not login as root.
base64 -d e-xxxxxxxxxxxx-cfg.tar.gz | tar -zx
3. Edit 'etc/passwd', remove root password: 'root::1:0:99999:7:::'.
4. Edit 'etc/rc.local', insert telnetd command before 'exit 0':
( sleep 3s; /usr/sbin/telnetd; ) &
5. Repack the configuration:
tar -zc etc/ | base64 > e-xxxxxxxxxxxx-cfg.tar.gz
6. Upload new configuration via web interface, now you can connect to
ASR3000 via telnet.
Flash instructions:
1. Connect to ASR3000, backup everything, especially 'Factory' part.
2. Write new BL2:
mtd write openwrt-mediatek-filogic-abt_asr3000-preloader.bin BL2
3. Write new FIP:
mtd write openwrt-mediatek-filogic-abt_asr3000-bl31-uboot.fip FIP
4. Set static IP on your PC:
IP 192.168.1.254/24, GW 192.168.1.1
5. Serve OpenWrt initramfs image using TFTP server.
6. Cut off the power and re-engage, wait for TFTP recovery to complete.
7. After OpenWrt has booted, perform sysupgrade.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/15887
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
There is no point in hard-coding the UBI volume numbers as we are
dynamically looking up the volume by volume name in all cases by now.
Remove this relict as it causes problems without being useful for
anything.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
1. Rename function _do_env_set() to env_do_env_set().
2. Replace kwbimage hack with UBOOT_CUSTOMIZE_CONFIG:
"--disable TOOLS_KWBIMAGE" and "--disable TOOLS_LIBCRYPTO".
3. Disable CONFIG_CMD_BOOTEFI_BOOTMGR for all supported devices
because the newly added UEFI bootmenu entries doesn't work.
4. Enable CONFIG_VERSION_VARIABLE for the OpenWrt One.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Co-authored-by: Daniel Golle <daniel@makrotopia.org>
The gpio is actually low active, fix it.
Fixes: 40e7fab9e4 ("mediatek: add Nokia EA0326GMP support")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/15651
Signed-off-by: Robert Marko <robimarko@gmail.com>
Hardware specification:
SoC: MediaTek MT7981B 2x A53
Flash: 128 MB SPI-NAND
RAM: 256MB
Ethernet: 4x 10/100/1000 Mbps
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset, WPS/Mesh
Power: DC 12V 1A
Gain SSH access:
1. Login into web interface, and download the configuration.
2. Download the configration utilities:
https://firmware.download.immortalwrt.eu.org/cnsztl/mediatek/filogic/openwrt-mediatek-mt7981-nokia-ea0326gmp-config-utils.tar.gz
These binaries are extraced from the factory firmware, which are
dynamically linked with aarch64 musl 1.1.24. To use them, you
must run them under the same runtime environment, otherwise the
binaries will not work properly!
3. Upload the configuration and utilities to a suitable environment.
4. Uncompress the utilities, move them to '/bin' and give them executable permisison:
tar -zxf openwrt-mediatek-mt7981-nokia-ea0326gmp-config-utils.tar.gz
mv mkconfig seama /bin
chmod +x /bin/mkconfig
chmod +x /bin/seama
5. Decrypt and uncompress the configuration:
Enter fakeroot if you are not login as root.
mkconfig -a de-enca -m EA0326GMP_3FE79221BAAA -i EA0326GMP_3FE79221BAAA-xxxxxxxx-backup.tar.gz -o backup.tar.gz
tar -zxf backup.tar.gz
6. Edit 'etc/config/dropbear', set 'enable' to '1'.
7. Edit 'etc/passwd', remove root password: 'root::1:0:99999:7:::'.
8. Repack the configuration:
tar -zcf backup.tar.gz etc/
mkconfig -a enca -m EA0326GMP_3FE79221BAAA -i backup.tar.gz -o EA0326GMP_3FE79221BAAA-xxxxxxxx-backup.tar.gz
9. Upload new configuration via web interface, now you can SSH to EA0326GMP.
A minimum configuration which enabled SSH access is also provided
to simplify the process:
https://firmware.download.immortalwrt.eu.org/cnsztl/mediatek/filogic/openwrt-mediatek-mt7981-nokia-ea0326gmp-enable-ssh.tar.gz
Flash instructions:
1. SSH to EA0326GMP, backup everything, especially 'Factory' part.
2. Write new BL2:
mtd write openwrt-mediatek-filogic-nokia_ea0326gmp-preloader.bin BL2
3. Write new FIP:
mtd write openwrt-mediatek-filogic-nokia_ea0326gmp-bl31-uboot.fip FIP
4. Set static IP on your PC:
IP 192.168.1.254/24, GW 192.168.1.1
5. Serve OpenWrt initramfs image using TFTP server.
6. Cut off the power and re-engage, wait for TFTP recovery to complete.
7. After OpenWrt has booted, perform sysupgrade.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Dont allow x2 read and cache read operations on FM35Q1GA as they seem
to be unstable. Also the Linux drivers does not allow x2 ops.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add ubi volumes for mt7988a-rfb and support for using factory data
for Ethernet MAC addresses and MT7996 WLAN calibration data.
Also add rootdisk handle. Removes the need to keep using nmbm
Signed-off-by: Felix Fietkau <nbd@nbd.name>
With the switch from the uImage.FIT partition parser to fitblk the
cmdline needs to be adjusted as well. Do this now as it has been
forgotten when the switch was done.
Fixes: 6368ed1ae5 ("mediatek: mt7623: phase out uImage.FIT partition parser")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This adds support for the bpi-r4 variant with internal 2.5G PHY and
additional ethernet port instead of second sfp.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Add support for Xiaomi Redmi AX6S to be used as a second-stage
UBI loader.
The defconfig/env is minimal: Boot fit from UBI. If that failed,
load and boot initramfs image from TFTP.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Make sure patch sequence number is unique by moving patch
440-add-jdcloud_re-cp-03.patch -> 441-add-jdcloud_re-cp-03.patch
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Probing of the fitblk driver in some situations happens after Linux
attempts to mount rootfs, which then fails.
Always use 'rootwait' kernel parameter when using fitblk for rootfs.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Use the new fitblk driver on the BananaPi R2 as well as UniElec U7623.
Introduce boot device selection for fitblk's /chosen/rootdisk
handle, similar to how it is already done on MT7622, MT7986 and MT7988.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The default environment for the Linksys E8450 and Belkin RT3200 got
truncated by one line due to a broken patch. While the impact was
luckily only cosmetic, fix it so bootmenu title also shows U-Boot
version again.
Fixes: 6aec3c7b5b ("mediatek: mt7622: modernize Linksys E8450 / Belkin RT3200 UBI build")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Fix NAND flash layout which was out-of-sync with the definition in
ARM TrustedFirmware-A which expects UBI to start at 0x200000.
Fixes: b03d3644cf ("mediatek: filogic: add BananaPi BPi-R3 mini")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The R3 mini comes with two Airoha EN8811H PHYs for 2.5G Ethernet.
The driver added to U-Boot expects the firmware for the PHY to be
stored inside UBI volume en8811h-fw or MMC boot1 hardware partition.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Move fip and factory into UBI static volumes.
Use fitblk instead of partition parser.
!! RUN INSTALLER FIRST !!
Existing users of previous OpenWrt releases or snapshot builds will
have to **re-run the updated installer** before upgrading to firmware
after this commit.
DO NOT flash or run even just the initramfs image unless you have
run the updated installer which moves the content of the 'factory'
partition into a UBI volume.
tl;dr: DON'T USE YET!
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Modernize bootloader and flash memory layout of the BPi-R64 similar to
how it has also been done for the BPi-R3.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Modernize U-Boot to provide a better reference:
* store fip image in UBI now that TF-A supports that
* switch from uImage.FIT partition parser to new fitblk
virtual firmware block driver (root=/dev/fit0)
* automatically set root device according to boot_mode register
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Rebase local patches on top of quarterly timed release, allowing to
drop numerous patches which have been accepted upstream since the
release of U-Boot 2023.07.02.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
If nodes /chosen/rootdisk-${bootdevice} exists, set /chosen/rootdisk
phandle according to boot device selected by the bootstrap pins.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
When erasing large amounts of blocks at once this can take a long
time on slow cards. Instead of a fixed timeout, wait longer if more
blocks are being erased.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add basic U-Boot drop-in replacement compatible with the flash layout
of the vendor loader of the Zbtlink WG3526 (16M) MT7621 router board.
The idea here is a to have a reference build of uboot-mediatek also for
a simple MIPS boards more popular than MT7621 RFB.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
