mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-26 17:01:14 +00:00
552d76f2be
352 Commits
| Author | SHA1 | Message | Date | |
|---|---|---|---|---|
Mikhail Zhilkin
|
bd783fd60a |
ramips: add support for Beeline SmartBox GIGA
Beeline SmartBox GIGA is a wireless WiFi 5 router manufactured by
Sercomm company.
Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 256 MiB, Nanya NT5CC128M16JR-EK
Flash: 128 MiB, Macronix MX30LF1G18AC
Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2
Wireless 5 GHz (MT7613BE): a/n/ac, 2x2
Ethernet: 3 ports - 2xGbE (WAN, LAN1), 1xFE (LAN2)
USB ports: 1xUSB3.0
Button: 1 button (Reset/WPS)
PCB ID: DBE00B-1.6MM
LEDs: 1 RGB LED
Power: 12 VDC, 1.5 A
Connector type: barrel
Bootloader: U-Boot
Installation
-----------------
1. Downgrade stock (Beeline) firmware to v.1.0.02;
2. Give factory OpenWrt image a shorter name, e.g. 1001.img;
3. Upload and update the firmware via the original web interface.
Remark: You might need make the 3rd step twice if your running firmware
is booted from the Slot 1 (Sercomm0 bootflag). The stock firmware
reverses the bootflag (Sercomm0 / Sercomm1) on each firmware update.
Revert to stock
---------------
1. Change the bootflag to Sercomm1 in OpenWrt CLI and then reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
2. Optional: Update with any stock (Beeline) firmware if you want to
overwrite OpenWrt in Slot 0 completely.
MAC Addresses
-------------
+-----+-----------+---------+
| use | address | example |
+-----+-----------+---------+
| LAN | label | *:16 |
| WAN | label + 1 | *:17 |
| 2g | label + 4 | *:1a |
| 5g | label + 5 | *:1b |
+-----+-----------+---------+
The label MAC address was found in Factory 0x21000
Notes
-----
1. The following scripts are required for the build:
sercomm-crypto.py - already exists in OpenWrt
sercomm-partition-tag.py - already exists in OpenWrt
sercomm-payload.py - already exists in OpenWrt
sercomm-pid.py - new, the part of this pull request
sercomm-kernel-header.py - new, the part of this pull request
2. This device (same as other Sercomm S2,S3-based devices) requires
special LZMA and LOADADDR settings for successful boot:
LZMA_TEXT_START=0x82800000
KERNEL_LOADADDR=0x81001000
LOADADDR=0x80001000
3. This device (same as several other Sercomm-based devices - Beeline,
Netgear, Etisalat, Rostelecom) has partition map (mtd1) containing
real partition offsets, which may differ from device to device
depending on the number and location of bad blocks on NAND.
"fixed-partitions" is used if the partition map is not found or
corrupted. This behavour (it's the same as on stock firmware) is
provided by MTD_SERCOMM_PARTS module.
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
|
||
Robert Marko
|
57a38c8d3e |
mvebu: add Methode euroDPU support
Add support for Methode euroDPU which is based on uDPU but does not have a second SFP cage, instead of which a Maxlinear G.hn IC is used. PHY mode is set to 1000Base-X despite Maxlinear IC being capable of 2500Base-X since until 5.15 support for mvebu is available trying to use 2500Base-X will cause buffer overruns for which the fix is not easily backportable. Installation instructions: 1. Boot the FIT initramfs image (openwrt-mvebu-cortexa53-methode_edpu-initramfs.itb) 2. sysupgrade using the openwrt-mvebu-cortexa53-methode_edpu-firmware.tgz Signed-off-by: Robert Marko <robert.marko@sartura.hr> |
||
|
Robert Marko
|
7f73acade0 |
mvebu: update and refactor uDPU DTS
uDPU DTS has pending upstream fixups, so backport those as well as split the DTS into a DTSI and DTS in preparation for euroDPU support which uses uDPU as the base. Ethernet aliases have not yet been sent upstream but will be soon in order for U-boot to set the correct MAC on both ethernet interfaces instead of just one. Since U-boot environment now has its own partition, update the envtools config script to search for it instead. Patch hardcoding PHY mode is also not applicable anymore, so drop it and set in the uDPU DTS directly. Signed-off-by: Robert Marko <robert.marko@sartura.hr> |
||
Chris Blake
|
949e8ba521 |
ath79: add support for Netgear PGZNG1
This adds support for the Netgear PGZNG1, also known as the ADT Pulse
Gateway.
Hardware:
CPU: Atheros AR9344
Memory: 256MB
Storage: 256MB NAND Hynix H27U2G8F2CTR-BC
USB: 1x USB 2.0
Ethernet: 2x 100Mb/s
WiFi: Atheros AR9340 2.4GHz 2T2R
Leds: 8 LEDs
Button: 1x Reset Button
UART:
Header marked JPE1. Pinout is VCC, TX, RX, GND. The marked pin, closest
to the JPE1 marking, is VCC. Note VCC isn't required to be connected
for UART to work.
Enable Stock Firmware Shell Access:
1. Interrupt u-boot and run the following commands
setenv console_mode 1
saveenv
reset
This will enable a UART shell in the firmware. You can then login using
the root password of `icontrol`. If that doesn't work, the device is
running a firmware based on OpenWRT where you can drop into failsafe to
mount the FS and then modify /etc/passwd.
Installation Instructions:
1. Interupt u-boot and run the following commands
setenv active_image 0
setenv stock_bootcmd nboot 0x81000000 0 \${kernel_offset}
setenv openwrt_bootcmd nboot 0x82000000 0 \${kernel_offset}
setenv bootcmd run openwrt_bootcmd
saveenv
2. boot initramfs image via TFTP u-boot
tftpboot 0x82000000 openwrt-ath79-nand-netgear_pgzng1-initramfs-kernel.bin; bootm 0x82000000
3. Once booted, use LuCI sysupgrade to
flash openwrt-ath79-nand-netgear_pgzng1-squashfs-sysupgrade.bin
MAC Table:
WAN (eth0): xx:xa - caldata 0x0
LAN (eth1): xx:xb - caldata 0x6
WLAN (phy0): xx:xc - burned into ath9k caldata
Not Working:
Z-Wave
RS422
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
(added more hw-info, fixed file permissions)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
|
||
Christian Lamparter
|
5f7828fcc2 |
apm821xx: MBL: make mtd chip work
The MBL has a 512KiB Microchip SST39VF040 chip for uboot and not much else. Thanks to Ewald who figured out that the "jedec-probe" vs. "jedec-flash" was the wrong binding. With this information and the jedec-probe support enabled => the chip works. | physmap-flash 4fff80000.nor_flash: physmap platform flash device: [mem 0x4fff80000-0x4ffffffff] | Found: SST 39LF040 | 4fff80000.nor_flash: Found 1 x8 devices at 0x0 in 8-bit bank Suggested-by: Ewald Comhaire <e.comhaire@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> |
||
Markus Stockhausen
|
6153c530cc |
realtek: add support for D-Link DGS-1210-20
Hardware specification
----------------------
* RTL8382M SoC, 1 MIPS 4KEc core @ 500MHz
* 128MB DRAM
* 32MB NOR Flash
* 16 x 10/100/1000BASE-T ports
- Internal PHY with 8 ports (RTL8218B)
- External PHY with 8 ports (RTL8218B)
* 4 x Gigabit RJ45/SFP Combo ports
- External PHY with 4 SFP ports (RTL8214FC)
* Power LED
* Reset button on front panel
* UART (115200 8N1) via unpopulated standard 0.1" pin header marked J6
UART pinout
-----------
[o]ooo|J6
| ||`------ GND
| |`------- RX
| `-------- TX
`---------- Vcc (3V3)
Boot initramfs image from U-Boot
--------------------------------
1. Press Escape key during `Hit Esc key to stop autoboot` prompt
2. Press CTRL+C keys to get into real U-Boot prompt
3. Init network with `rtk network on` command
4. Load image with `tftpboot 0x8f000000 openwrt-realtek-rtl838x-d-link_dgs-1210-20-initramfs-kernel.bin` command
5. Boot the image with `bootm` command
To install, upload the sysupgrade image to the OEM webpage or sysupgrade
from the system running from initramfs image.
It has been developed and tested on device with F1 revision.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
[correct initramfs image name]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
|
||
|
Mikhail Zhilkin
|
498c15376b |
ramips: add support for MTS WG430223
MTS WG430223 is a wireless AC1300 (WiFi 5) router manufactured by
Arcadyan company. It's very similar to Beeline Smartbox Flash (Arcadyan
WG443223).
Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 128 MiB
Flash: 128 MiB (Winbond W29N01HV)
Wireless 2.4 GHz (MT7615DN): b/g/n, 2x2
Wireless 5 GHz (MT7615DN): a/n/ac, 2x2
Ethernet: 3xGbE (WAN, LAN1, LAN2)
USB ports: No
Button: 1 (Reset/WPS)
LEDs: 2 (Red, Green)
Power: 12 VDC, 1 A
Connector type: Barrel
Bootloader: U-Boot (Ralink UBoot Version: 5.0.0.2)
OEM: Arcadyan WG430223
Installation
------------
1. Login to the router web interface (superadmin:serial number)
2. Navigate to Administration -> Miscellaneous -> Access control lists &
enable telnet & enable "Remote control from any IP address"
3. Connect to the router using telnet (default admin:admin)
4. Place *factory.trx on any web server (192.168.1.2 in this example)
5. Connect to the router using telnet shell (no password required)
6. Save MAC adresses to U-Boot environment:
uboot_env --set --name eth2macaddr --value $(ifconfig | grep eth2 | \
awk '{print $5}')
uboot_env --set --name eth3macaddr --value $(ifconfig | grep eth3 | \
awk '{print $5}')
uboot_env --set --name ra0macaddr --value $(ifconfig | grep ra0 | \
awk '{print $5}')
uboot_env --set --name rax0macaddr --value $(ifconfig | grep rax0 | \
awk '{print $5}')
7. Ensure that MACs were saved correctly:
uboot_env --get --name eth2macaddr
uboot_env --get --name eth3macaddr
uboot_env --get --name ra0macaddr
uboot_env --get --name rax0macaddr
8. Download and write the OpenWrt images:
cd /tmp
wget http://192.168.1.2/factory.trx
mtd_write erase /dev/mtd4
mtd_write write factory.trx /dev/mtd4
9. Set 1st boot partition and reboot:
uboot_env --set --name bootpartition --value 0
Back to Stock
-------------
1. Run in the OpenWrt shell:
fw_setenv bootpartition 1
reboot
2. Optional step. Upgrade the stock firmware with any version to
overwrite the OpenWrt in Slot 1.
MAC addresses
-------------
+-----------+-------------------+----------------+
| Interface | MAC | Source |
+-----------+-------------------+----------------+
| label | A4:xx:xx:51:xx:F4 | No MACs was |
| LAN | A4:xx:xx:51:xx:F6 | found on Flash |
| WAN | A4:xx:xx:51:xx:F4 | [1] |
| WLAN_2g | A4:xx:xx:51:xx:F5 | |
| WLAN_5g | A6:xx:xx:21:xx:F5 | |
+-----------+-------------------+----------------+
[1]:
a. Label wasb't found neither in factory nor in other places.
b. MAC addresses are stored in encrypted partition "glbcfg". Encryption
key hasn't known yet. To ensure the correct MACs in OpenWrt, a hack
with saving of the MACs to u-boot-env during the installation was
applied.
c. Default Ralink ethernet MAC address (00:0C:43:28:80:A0) was found in
"Factory" 0xfff0. It's the same for all MTS WG430223 devices. OEM
firmware also uses this MAC when initialazes ethernet driver. In
OpenWrt we use it only as internal GMAC (eth0), all other MACs are
unique. Therefore, there is no any barriers to the operation of several
MTS WG430223 devices even within the same broadcast domain.
Stock firmware image format
---------------------------
The same as Beeline Smartbox Flash but with another trx magic
+--------------+---------------+----------------------------------------+
| Offset | | Description |
+==============+===============+========================================+
| 0x0 | 31 52 48 53 | TRX magic "1RHS" |
+--------------+---------------+----------------------------------------+
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
|
||
Raylynn Knight
|
b515ad10a6 |
realtek: add support for ZyXEL GS1900-24E
The ZyXEL GS1900-24E is a 24 port gigabit switch similar to other GS1900
switches.
Specifications
--------------
* Device: ZyXEL GS1900-24E
* SoC: Realtek RTL8382M 500 MHz MIPS 4KEc
* Flash: 16 MiB Macronix MX25L12835F
* RAM: 128 MiB DDR2 SDRAM Nanya NT5TU128M8GE
* Ethernet: 24x 10/100/1000 Mbps
* LEDs: 1 PWR LED (green, not configurable)
1 SYS LED (green, configurable)
24 ethernet port link/activity LEDs (green, SoC controlled)
* Buttons: 1 "RESET" button on front panel
* Switch: 1 Power switch on rear of device
* Power 120-240V AC C13
* UART: 1 serial header (JP2) with populated standard pin connector on
the left side of the PCB.
Pinout (front to back):
+ Pin 1 - VCC marked with white dot
+ Pin 2 - RX
+ Pin 3 - TX
+ PIn 4 - GND
Serial connection parameters: 115200 8N1.
Installation
------------
OEM upgrade method:
* Log in to OEM management web interface
* Navigate to Maintenance > Firmware
* Select the HTTP radio button
* Select the Active radio button
* Use the browse button to locate the
realtek-rtl838x-zyxel_gs1900-24e-initramfs-kernel.bin
file and select open so File Path is updated with filename.
* Select the Apply button. Screen will display "Prepare
for firmware upgrade ...".
*Wait until screen shows "Do you really want to reboot?"
then select the OK button
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade -n /tmp/realtek-rtl838x-zyxel_gs1900-24e-squashfs-sysupgrade.bin
it may be necessary to restart the network (/etc/init.d/network restart) on
the running initramfs image.
U-Boot TFTP method:
* Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10).
* Set up a TFTP server on your client and make it serve the initramfs image.
* Connect serial, power up the switch, interrupt U-boot by hitting the
space bar, and enable the network:
> rtk network on
* Since the GS1900-24E is a dual-partition device, you want to keep the OEM
firmware on the backup partition for the time being. OpenWrt can only boot
from the first partition anyway (hardcoded in the DTS). To make sure we are
manipulating the first partition, issue the following commands:
> setsys bootpartition 0
> savesys
* Download the image onto the device and boot from it:
> tftpboot 0x84f00000 192.168.1.10:openwrt-realtek-rtl838x-zyxel_gs1900-24e-initramfs-kernel.bin
> bootm
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade -n /tmp/openwrt-realtek-rtl838x-zyxel_gs1900-24e-squashfs-sysupgrade.bin
it may be necessary to restart the network (/etc/init.d/network restart) on
the running initramfs image.
Signed-off-by: Raylynn Knight <rayknight@me.com>
|
||
Peter Adkins
|
b4184c666c |
ipq40xx: add support for Linksys WHW01 v1
This patch adds support for Linksys WHW01 v1 ("Velop") [FCC ID Q87-03331].
Specification
-------------
SOC: Qualcomm IPQ4018
WiFi 1: Qualcomm QCA4019 IEEE 802.11b/g/n
WiFi 2: Qualcomm QCA4019 IEEE 802.11a/n/ac
Bluetooth: Qualcomm CSR8811 (A12U)
Ethernet: Qualcomm QCA8072 (2-port)
SPI Flash 1: Mactronix MX25L1605D (2MB)
SPI Flash 2: Winbond W25M02GV (256MB)
DRAM: Nanya NT5CC128M16IP-DI (256MB)
LED Controller: NXP PCA963x (I2C)
Buttons: Single reset button (GPIO).
Notes
-----
There does not appear to be a way to trigger TFTP recovery without entering
U-Boot. The device must be opened to access the serial console in order to
first flash OpenWrt onto a device from factory.
The device has automatic recovery backed by a second set of partitions on
the larger of the two SPI flash ICs. Both the primary and secondary must
be flashed to prevent accidental rollback to "factory" after 3 failed boot
attempts.
Serial console
--------------
A serial console is available on the following pins of the populated J2
connector on the device mainboard (115200 8n1).
(<-- Top of PCB / Device)
J2
[o o o o o o]
| | |
| | `-- GND
| `---- TX
`--------- RX
Installation instructions
-------------------------
1. Setup TFTP server with server IP set to 192.168.1.236.
2. Copy compiled `...squashfs-factory.bin` to `nodes-jr.img` in tftp root.
3. Connect to console using pinout detailed in the serial console section.
4. Power on device and press enter when prompted to drop into U-Boot.
5. Flash first partition device via `run flashimg`.
6. Once complete, reset device and allow to power up completely.
7. Once comfortable with device upgrade reboot and drop back into U-Boot.
8. Flash the second partition (recovery) via `run flashimg2`.
Revert to "factory"
-------------------
1. Download latest firmware update from vendor support site.
2. Copy extracted `.img` file to `nodes-jr.img` in tftp root.
3. Connect to console using pinout detailed in the serial console section.
4. Power on device and press enter when prompted to drop into U-Boot.
5. Flash first partition device via `run flashimg`.
6. Once complete, reset device and allow to power up completely.
7. Once comfortable with device upgrade reboot and drop back into U-Boot.
8. Flash the second partition (recovery) via `run flashimg2`.
Link: https://github.com/openwrt/openwrt/pull/3682
Signed-off-by: Peter Adkins <peter@sunkenlab.com>
(calibration from nvmem, updated to 5.10+5.15)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
|
||
|
Raylynn Knight
|
580723e86a |
realtek: add support for ZyXEL GS1900-16
The ZyXEL GS1900-16 is a 16 port gigabit switch similar to other GS1900 switches.
Specifications
--------------
* Device: ZyXEL GS1900-16
* SoC: Realtek RTL8382M 500 MHz MIPS 4KEc
* Flash: 16 MiB Macronix MX25L12835F
* RAM: 128 MiB DDR2 SDRAM Nanya NT5TU128M8HE
* Ethernet: 16x 10/100/1000 Mbps
* LEDs: 1 PWR LED (green, not configurable)
1 SYS LED (green, configurable)
16 ethernet port link/activity LEDs (green, SoC controlled)
* Buttons: 1 "RESET" button on front panel
* Power 120-240V AC C13
* UART: 1 serial header (J12) with populated standard pin connector on
the right back of the PCB.
Pinout (front to back):
+ Pin 1 - VCC marked with white dot
+ Pin 2 - RX
+ Pin 3 - TX
+ PIn 4 - GND
Serial connection parameters: 115200 8N1.
Installation
------------
OEM upgrade method:
* Log in to OEM management web interface
* Navigate to Maintenance > Firmware
* Select the HTTP radio button
* Select the Active radio button
* Use the browse button to locate the
realtek-generic-zyxel_gs1900-16-initramfs-kernel.bin
file amd select open so File Path is update with filename.
* Select the Apply button. Screen will display "Prepare
for firmware upgrade ...".
*Wait until screen shows "Do you really want to reboot?"
then select the OK button
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade -n /tmp/realtek-generic-zyxel_gs1900-16-squashfs-sysupgrade.bin
it may be necessary to restart the network (/etc/init.d/network restart) on
the running initramfs image.
U-Boot TFTP method:
* Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10).
* Set up a TFTP server on your client and make it serve the initramfs image.
* Connect serial, power up the switch, interrupt U-boot by hitting the
space bar, and enable the network:
> rtk network on
* Since the GS1900-16 is a dual-partition device, you want to keep the OEM
firmware on the backup partition for the time being. OpenWrt can only boot
from the first partition anyway (hardcoded in the DTS). To make sure we are
manipulating the first partition, issue the following commands:
> setsys bootpartition 0
> savesys
* Download the image onto the device and boot from it:
> tftpboot 0x84f00000 192.168.1.10:openwrt-realtek-generic-zyxel_gs1900-16-initramfs-kernel.bin
> bootm
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade -n /tmp/openwrt-realtek-generic-zyxel_gs1900-16-squashfs-sysupgrade.bin
it may be necessary to restart the network (/etc/init.d/network restart) on
the running initramfs image.
Signed-off-by: Raylynn Knight <rayknight@me.com>
[removed duplicate patch title, align RAM specification]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
|
||
Rodrigo Balerdi
|
f8b0010dfb |
ipq806x: add support for Arris TR4400 v2 / RAC2V1A
Hardware specs:
SoC: Qualcomm IPQ8065 (dual core Cortex-A15)
RAM: 512 MB DDR3
Flash: 256 MB NAND, 32 MB NOR
WiFi: QCA9983 2.4 GHz, QCA9984 5 GHz
Switch: QCA8337
Ethernet: 5x 10/100/1000 Mbit/s
USB: 1x USB 3.0 Type-A
Buttons: WPS, Reset
Power: 12 VDC, 2.5 A
Ethernet ports:
1x WAN: connected to eth2
4x LAN: connected via the switch to eth0 and eth1
(eth0 is disabled in OEM firmware)
MAC addresses (OEM and OpenWrt):
fw_env @ 0x00 d4🆎82:??:??:?a LAN (eth1)
fw_env @ 0x06 d4🆎82:??:??:?b WAN (eth2)
fw_env @ 0x0c d4🆎82:??:??:?c WLAN 2.4 GHz (ath1)
fw_env @ 0x12 d4🆎82:??:??:?d WLAN 5 GHz (ath0)
fw_env @ 0x18 d4🆎82:??:??:?e OEM usage unknown (eth0 in OpenWrt)
OID d4🆎82 is registered to:
ARRIS Group, Inc., 6450 Sequence Drive, San Diego CA 92121, US
More info:
https://openwrt.org/inbox/toh/arris/tr4400_v2
IMPORTANT:
This port requires moving the 'fw_env' partition prior to first boot to
consolidate 70% of the usable space in flash into a contiguous partition.
'fw_env' contains factory-programmed MAC addresses, SSIDs, and passwords.
Its contents must be copied to 'rootfs_1' prior to booting via initramfs.
Note that the stock 'fw_env' partition will be wiped during sysupgrade.
A writable 'stock_fw_env' partition pointing to the old, stock location
is included in the port to help rolling back this change if desired.
Installation:
- Requires serial access and a TFTP server.
- Fully boot stock, press ENTER, type in:
mtd erase /dev/mtd21
dd if=/dev/mtd22 bs=128K count=1 | mtd write - /dev/mtd21
umount /config && ubidetach -m 23 && mtd erase /dev/mtd23
- Reboot and interrupt U-Boot by pressing a key, type in:
set mtdids 'nand0=nand0'
set mtdparts 'mtdparts=nand0:155M@0x6500000(mtd_ubi)'
set bootcmd 'ubi part mtd_ubi && ubi read 0x44000000 kernel && bootm'
env save
- Setup TFTP server serving initramfs image as 'recovery.bin', type in:
set ipaddr 192.168.1.1
set serverip 192.168.1.2
tftpboot recovery.bin && bootm
- Use sysupgrade to install squashfs image.
This port is based on work done by AmadeusGhost <amadeus@jmu.edu.cn>.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
[add 5.15 changes for 0069-arm-boot-add-dts-files.patch]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
|
||
David Bauer
|
fb7ff6b027 |
uboot-envtools: add WS-AP3825i config
Add configuration to use uboot-envtools with the Extreme Networks WS-AP3825i. Signed-off-by: David Bauer <mail@david-bauer.net> |
||
Clemens Hopfer
|
4891b86538 |
ramips: add support for YunCore AX820/HWAP-AX820
There are two versions which are identical apart from the enclosure: YunCore AX820: indoor ceiling mount AP with integrated antennas YunCore HWAP-AX820: outdoor enclosure with external (N) connectors Hardware specs: SoC: MediaTek MT7621DAT Flash: 16 MiB SPI NOR RAM: 128MiB (DDR3, integrated) WiFi: MT7905DAN+MT7975DN 2.4/5GHz 2T2R 802.11ax Ethernet: 10/100/1000 Mbps x2 (WAN/PoE+LAN) LED: Status (green) Button: Reset Power: 802.11af/at PoE; DC 12V,1A Antennas: AX820(indoor): 4dBi internal; HWAP-AX820(outdoor): external Flash instructions: The "OpenWRT support" version of the AX820 comes with a LEDE-based firmware with proprietary MTK drivers and a luci webinterface and ssh accessible under 192.168.1.1 on LAN; user root, no password. The sysupgrade.bin can be flashed using luci or sysupgrade via ssh, you will have to force the upgrade due to a different factory name. Remember: Do *not* preserve factory configuration! MAC addresses as used by OEM firmware: use address source 2g 44:D1:FA:*:0b Factory 0x0004 (label) 5g 46:D1:FA:*:0b LAA of 2g lan 44:D1:FA:*:0c Factory 0xe000 wan 44:D1:FA:*:0d Factory 0xe000 + 1 The wan MAC can also be found in 0xe006 but is not used by OEM dtb. Due to different MAC handling in mt76 the LAA derived from lan is used for 2g to prevent duplicate MACs when creating multiple interfaces. Signed-off-by: Clemens Hopfer <openwrt@wireloss.net> |
||
Martin Kennedy
|
a5ac8ad0ba |
realtek: add ZyXEL GS1900-24HP v1 support
The ZyXEL GS1900-24HP v1 is a 24 port PoE switch with two SFP ports,
similar to the other GS1900 switches.
Specifications
--------------
* Device: ZyXEL GS1900-24HP v1
* SoC: Realtek RTL8382M 500 MHz MIPS 4KEc
* Flash: 16 MiB
* RAM: Winbond W9751G8KB-25 64 MiB DDR2 SDRAM
* Ethernet: 24x 10/100/1000 Mbps, 2x SFP 100/1000 Mbps
* LEDs:
* 1 PWR LED (green, not configurable)
* 1 SYS LED (green, configurable)
* 24 ethernet port link/activity LEDs (green, SoC controlled)
* 24 ethernet port PoE status LEDs
* 2 SFP status/activity LEDs (green, SoC controlled)
* Buttons:
* 1 "RESET" button on front panel (soft reset)
* 1 button ('SW1') behind right hex grate (hardwired power-off)
* PoE:
* Management MCU: ST Micro ST32F100 Microcontroller
* 6 BCM59111 PSE chips
* 170W power budget
* Power: 120-240V AC C13
* UART: Internal populated 10-pin header ('J5') providing RS232;
connected to SoC UART through a TI or SIPEX 3232C for voltage
level shifting.
* 'J5' RS232 Pinout (dot as pin 1):
2) SoC RXD
3) GND
10) SoC TXD
Serial connection parameters: 115200 8N1.
Installation
------------
OEM upgrade method:
* Log in to OEM management web interface
* Navigate to Maintenance > Firmware > Management
* If "Active Image" has the first option selected, OpenWrt will need to be
flashed to the "Active" partition. If the second option is selected,
OpenWrt will need to be flashed to the "Backup" partition.
* Navigate to Maintenance > Firmware > Upload
* Upload the openwrt-realtek-rtl838x-zyxel_gs1900-24hp-v1-initramfs-kernel.bin
file by your preferred method to the previously determined partition.
When prompted, select to boot from the newly flashed image, and reboot
the switch.
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade /tmp/openwrt-realtek-rtl838x-zyxel_gs1900-24hp-v1-squashfs-sysupgrade.bin
U-Boot TFTP method:
* Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10).
* Set up a TFTP server on your client and make it serve the initramfs
image.
* Connect serial, power up the switch, interrupt U-boot by hitting the
space bar, and enable the network:
> rtk network on
* Since the GS1900-24HP v1 is a dual-partition device, you want to keep the
OEM firmware on the backup partition for the time being. OpenWrt can
only be installed in the first partition anyway (hardcoded in the
DTS). To ensure we are set to boot from the first partition, issue the
following commands:
> setsys bootpartition 0
> savesys
* Download the image onto the device and boot from it:
> tftpboot 0x81f00000 192.168.1.10:openwrt-realtek-rtl838x-zyxel_gs1900-24hp-v1-initramfs-kernel.bin
> bootm
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade /tmp/openwrt-realtek-rtl838x-zyxel_gs1900-24hp-v1-squashfs-sysupgrade.bin
Signed-off-by: Martin Kennedy <hurricos@gmail.com>
[Add info on PoE hardware to commit message]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
|
||
Andrew Powers-Holmes
|
6f1efb2898 |
ath79: add support for Sophos AP100/AP55 family
The Sophos AP100, AP100C, AP55, and AP55C are dual-band 802.11ac access
points based on the Qualcomm QCA9558 SoC. They share PCB designs with
several devices that already have partial or full support, most notably the
Devolo DVL1750i/e.
The AP100 and AP100C are hardware-identical to the AP55 and AP55C, however
the 55 models' ART does not contain calibration data for their third chain
despite it being present on the PCB.
Specifications common to all models:
- Qualcomm QCA9558 SoC @ 720 MHz (MIPS 74Kc Big-endian processor)
- 128 MB RAM
- 16 MB SPI flash
- 1x 10/100/1000 Mbps Ethernet port, 802.3af PoE-in
- Green and Red status LEDs sharing a single external light-pipe
- Reset button on PCB[1]
- Piezo beeper on PCB[2]
- Serial UART header on PCB
- Alternate power supply via 5.5x2.1mm DC jack @ 12 VDC
Unique to AP100 and AP100C:
- 3T3R 2.4GHz 802.11b/g/n via SoC WMAC
- 3T3R 5.8GHz 802.11a/n/ac via QCA9880 (PCI Express)
AP55 and AP55C:
- 2T2R 2.4GHz 802.11b/g/n via SoC WMAC
- 2T2R 5.8GHz 802.11a/n/ac via QCA9880 (PCI Express)
AP100 and AP55:
- External RJ45 serial console port[3]
- USB 2.0 Type A port, power controlled via GPIO 11
Flashing instructions:
This firmware can be flashed either via a compatible Sophos SG or XG
firewall appliance, which does not require disassembling the device, or via
the U-Boot console available on the internal UART header.
To flash via XG appliance:
- Register on Sophos' website for a no-cost Home Use XG firewall license
- Download and install the XG software on a compatible PC or virtual
machine, complete initial appliance setup, and enable SSH console access
- Connect the target AP device to the XG appliance's LAN interface
- Approve the AP from the XG Web UI and wait until it shows as Active
(this can take 3-5 minutes)
- Connect to the XG appliance over SSH and access the Advanced Console
(Menu option 5, then menu option 3)
- Run `sudo awetool` and select the menu option to connect to an AP via
SSH. When prompted to enable SSH on the target AP, select Yes.
- Wait 2-3 minutes, then select the AP from the awetool menu again. This
will connect you to a root shell on the target AP.
- Copy the firmware to /tmp/openwrt.bin on the target AP via SCP/TFTP/etc
- Run `mtd -r write /tmp/openwrt.bin astaro_image`
- When complete, the access point will reboot to OpenWRT.
To flash via U-Boot serial console:
- Configure a TFTP server on your PC, and set IP address 192.168.99.8 with
netmask 255.255.255.0
- Copy the firmware .bin to the TFTP server and rename to 'uImage_AP100C'
- Open the target AP's enclosure and locate the 4-pin 3.3V UART header [4]
- Connect the AP ethernet to your PC's ethernet port
- Connect a terminal to the UART at 115200 8/N/1 as usual
- Power on the AP and press a key to cancel autoboot when prompted
- Run the following commands at the U-Boot console:
- `tftpboot`
- `cp.b $fileaddr 0x9f070000 $filesize`
- `boot`
- The access point will boot to OpenWRT.
MAC addresses as verified by OEM firmware:
use address source
LAN label config 0x201a (label)
2g label + 1 art 0x1002 (also found at config 0x2004)
5g label + 9 art 0x5006
Increments confirmed across three AP55C, two AP55, and one AP100C.
These changes have been tested to function on both current master and
21.02.0 without any obvious issues.
[1] Button is present but does not alter state of any GPIO on SoC
[2] Buzzer and driver circuitry is present on PCB but is not connected to
any GPIO. Shorting an unpopulated resistor next to the driver circuitry
should connect the buzzer to GPIO 4, but this is unconfirmed.
[3] This external RJ45 serial port is disabled in the OEM firmware, but
works in OpenWRT without additional configuration, at least on my
three test units.
[4] On AP100/AP55 models the UART header is accessible after removing
the device's top cover. On AP100C/AP55C models, the PCB must be removed
for access; three screws secure it to the case.
Pin 1 is marked on the silkscreen. Pins from 1-4 are 3.3V, GND, TX, RX
Signed-off-by: Andrew Powers-Holmes <andrew@omnom.net>
|
||
Abdul Aziz Amar
|
78c3534645 |
ramips: add support for BOLT! Arion
This device is from now-defunct BOLT! ISP in Indonesia.
The original firmware is based on mediatek SDK running linux 2.6 or 3.x in later revision.
Specifications:
- SoC: MediaTek MT7621
- Flash: 32 MiB NOR SPI
- RAM: 128 MiB DDR3
- Ethernet: 2x 10/100/1000 Mbps (switched, LAN + WAN)
- WIFI0: MT7603E 2.4GHz 802.11b/g/n
- WIFI1: MT7612E 5GHz 802.11ac
- Antennas: 2x internal, non-detachable
- LEDs: Programmable LEDs: 5 blue LEDs (wlan, tel, sig1-3) and 2 red LEDs (wlan and sig1)
Non-programmable "Power" LED
- Buttons: Reset and WPS
Instalation:
Install from TFTP
Set your PC IP to 10.10.10.3 and gateway to 10.10.10.123
Press "1" when turning on the router, and type the initramfs file name
You also need to solder pin header or cable to J4 or neighboring test points (T19-T21)
Pinouts from top to bottom: GND, TX, RX, VCC (3.3v)
Baudrate: 57600n8
There's also an additional gigabit transformer and RTL8211FD managed by the LTE module on the backside of the PCB.
Signed-off-by: Abdul Aziz Amar <abdulaziz.amar@gmail.com>
|
||
Thibaut VARÈNE
|
a05dcb0724 |
ath79: add support for Yuncore A930
Specification: - QCA9533 (650 MHz), 64 or 128MB RAM, 16MB SPI NOR - 2x 10/100 Mbps Ethernet, with 802.3at PoE support (WAN) - 2T2R 802.11b/g/n 2.4GHz Flash instructions: If your device comes with generic QSDK based firmware, you can login over telnet (login: root, empty password, default IP: 192.168.188.253), issue first (important!) 'fw_setenv' command and then perform regular upgrade, using 'sysupgrade -n -F ...' (you can use 'wget' to download image to the device, SSH server is not available): fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000" sysupgrade -n -F openwrt-...-yuncore_...-squashfs-sysupgrade.bin In case your device runs firmware with YunCore custom GUI, you can use U-Boot recovery mode: 1. Set a static IP 192.168.0.141/24 on PC and start TFTP server with 'tftp' image renamed to 'upgrade.bin' 2. Power the device with reset button pressed and release it after 5-7 seconds, recovery mode should start downloading image from server (unfortunately, there is no visible indication that recovery got enabled - in case of problems check TFTP server logs) Signed-off-by: Clemens Hopfer <openwrt@wireloss.net> Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org> |
||
|
Thibaut VARÈNE
|
c91df224f5 |
ath79: add support for Yuncore XD3200
Specification: - QCA9563 (775MHz), 128MB RAM, 16MB SPI NOR - 2T2R 802.11b/g/n 2.4GHz - 2T2R 802.11n/ac 5GHz - 2x 10/100/1000 Mbps Ethernet, with 802.3at PoE support (WAN port) LED for 5 GHz WLAN is currently not supported as it is connected directly to the QCA9882 radio chip. Flash instructions: If your device comes with generic QSDK based firmware, you can login over telnet (login: root, empty password, default IP: 192.168.188.253), issue first (important!) 'fw_setenv' command and then perform regular upgrade, using 'sysupgrade -n -F ...' (you can use 'wget' to download image to the device, SSH server is not available): fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000" sysupgrade -n -F openwrt-...-yuncore_...-squashfs-sysupgrade.bin In case your device runs firmware with YunCore custom GUI, you can use U-Boot recovery mode: 1. Set a static IP 192.168.0.141/24 on PC and start TFTP server with 'tftp' image renamed to 'upgrade.bin' 2. Power the device with reset button pressed and release it after 5-7 seconds, recovery mode should start downloading image from server (unfortunately, there is no visible indication that recovery got enabled - in case of problems check TFTP server logs) Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org> |
||
Daniel Golle
|
fa67639513 |
uboot-envtools: oxnas: fix wrong eraseblock size for shuttle,kd20
Shuttle KD20 has NAND flash with 0x20000 (128KiB) erase blocks. Correctly set that in uboot-envtools as well to allow writing to the bootloader environment using fw_setenv. Signed-off-by: Daniel Golle <daniel@makrotopia.org> |
||
Richard Huynh
|
9f9477b275 |
mediatek: Add support for Xiaomi Redmi Router AX6S
Also known as the "Xiaomi Router AX3200" in western markets, but only the AX6S is widely installation-capable at this time. SoC: MediaTek MT7622B RAM: DDR3 256 MiB (ESMT M15T2G16128A) Flash: SPI-NAND 128 MiB (ESMT F50L1G41LB or Gigadevice GD5F1GQ5xExxG) WLAN: 2.4/5 GHz 4T4R 2.4 GHz: MediaTek MT7622B 5 GHz: MediaTek MT7915E Ethernet: 4x 10/100/1000 Mbps Switch: MediaTek MT7531B LEDs/Keys: 2/2 (Internet + System LED, Mesh button + Reset pin) UART: Marked J1 on board VCC RX GND TX, beginning from "1". 3.3v, 115200n8 Power: 12 VDC, 1.5 A Notes: U-Boot passes through the ethaddr from uboot-env partition, but also has been known to reset it to a generic mac address hardcoded in the bootloader. However, bdata is also populated with the ethernet mac addresses, but is also typically never written to. Thus this is used instead. Installation: 1. Flash stock Xiaomi "closed beta" image labelled 'miwifi_rb03_firmware_stable_1.2.7_closedbeta.bin'. (MD5: 5eedf1632ac97bb5a6bb072c08603ed7) 2. Calculate telnet password from serial number and login 3. Execute commands to prepare device nvram set ssh_en=1 nvram set uart_en=1 nvram set boot_wait=on nvram set flag_boot_success=1 nvram set flag_try_sys1_failed=0 nvram set flag_try_sys2_failed=0 nvram commit 4. Download and flash image On computer: python -m http.server On router: cd /tmp wget http://<IP>:8000/factory.bin mtd -r write factory.bin firmware Device should reboot at this point. Reverting to stock: Stock Xiaomi recovery tftp that accepts their signed images, with default ips of 192.168.31.1 + 192.168.31.100. Stock image should be renamed to tftp server ip in hex (Eg. C0A81F64.img) Triggered by holding reset pin on powerup. A simple implementation of this would be via dnsmasq's dhcp-boot option or using the vendor's (Windows only) recovery tool available on their website. Signed-off-by: Richard Huynh <voxlympha@gmail.com> |
||
|
Mikhail Zhilkin
|
f8b02130d2 |
ramips: add support for Beeline SmartBox Flash
Beeline SmartBox Flash is a wireless AC1300 (WiFi 5) router manufactured
by Arcadyan company.
Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 256 MiB, Winbond W632GU6NB
Flash: 128 MiB (NAND), Winbond W29N01HVSINF
Wireless 2.4 GHz (MT7615DN): b/g/n, 2x2
Wireless 5 GHz (MT7615DN): a/n/ac, 2x2
Ethernet: 3xGbE (WAN, LAN1, LAN2)
USB ports: 1xUSB3.0
Button: 1 (Reset/WPS)
LEDs: 1 RGB LED
Power: 12 VDC, 1.5 A
Connector type: Barrel
Bootloader: U-Boot (Ralink UBoot Version: 5.0.0.2)
OEM: Arcadyan WE42022
Installation
------------
1. Place *factory.trx on any web server (192.168.1.2 in this example)
2. Connect to the router using telnet shell (no password required)
3. Save MAC adresses to U-Boot environment:
uboot_env --set --name eth2macaddr --value $(ifconfig | grep eth2 | \
awk '{print $5}')
uboot_env --set --name eth3macaddr --value $(ifconfig | grep eth3 | \
awk '{print $5}')
uboot_env --set --name ra0macaddr --value $(ifconfig | grep ra0 | \
awk '{print $5}')
uboot_env --set --name rax0macaddr --value $(ifconfig | grep rax0 | \
awk '{print $5}')
4. Ensure that MACs were saved correctly:
uboot_env --get --name eth2macaddr
uboot_env --get --name eth3macaddr
uboot_env --get --name ra0macaddr
uboot_env --get --name rax0macaddr
5. Download and write the OpenWrt images:
cd /tmp
wget http://192.168.1.2/factory.trx
mtd_write erase /dev/mtd4
mtd_write write factory.trx /dev/mtd4
6. Set 1st boot partition and reboot:
uboot_env --set --name bootpartition --value 0
reboot
Back to Stock
-------------
1. Run in the OpenWrt shell:
fw_setenv bootpartition 1
reboot
2. Optional step. Upgrade the stock firmware with any version to
overwrite the OpenWrt in Slot 1.
MAC addresses
-------------
+-----------+-------------------+----------------+
| Interface | MAC | Source |
+-----------+-------------------+----------------+
| label | 30:xx:xx:51:xx:09 | No MACs was |
| LAN | 30:xx:xx:51:xx:09 | found on Flash |
| WAN | 30:xx:xx:51:xx:06 | [1] |
| WLAN_2g | 30:xx:xx:51:xx:07 | |
| WLAN_5g | 32:xx:xx:41:xx:07 | |
+-----------+-------------------+----------------+
[1]:
a. Label wasb't found neither in factory nor in other places.
b. MAC addresses are stored in encrypted partition "glbcfg". Encryption
key hasn't known yet. To ensure the correct MACs in OpenWrt, a hack
with saving of the MACs to u-boot-env during the installation was
applied.
c. Default Ralink ethernet MAC address (00:0C:43:28:80:36) was found in
"Factory" 0xfff0. It's the same for all Smartbox Flash devices. OEM
firmware also uses this MAC when initialazes ethernet driver. In
OpenWrt we use it only as internal GMAC (eth0), all other MACs are
unique. Therefore, there is no any barriers to the operation of several
Smartbox Flash devices even within the same broadcast domain.
Stock firmware image format
---------------------------
+--------------+---------------+----------------------------------------+
| Offset | 1.0.15 | Description |
+==============+===============+========================================+
| 0x0 | 5d 43 6f 74 | TRX magic "]Cot" |
+--------------+---------------+----------------------------------------+
| 0x4 | 00 70 ff 00 | Length (reverse) |
+--------------+---------------+----------------------------------------+
| | | htonl(~crc) from 0xc ("flag_version") |
| 0x8 | 72 b3 93 16 | to "Length" |
+--------------+---------------+----------------------------------------+
| 0xc | 00 00 01 00 | Flags |
+--------------+---------------+----------------------------------------+
| | | Offset (reverse) of Kernel partition |
| 0x10 | 1c 00 00 00 | from the start of the header |
+--------------+---------------+----------------------------------------+
| | | Offset (reverse) of RootFS partition |
| 0x14 | 00 00 42 00 | from the start of the header |
+--------------+---------------+----------------------------------------+
| 0x18 | 00 00 00 00 | Zeroes |
+--------------+---------------+----------------------------------------+
| 0x1c | 27 05 19 56 … | Kernel data + zero padding |
+--------------+---------------+----------------------------------------+
| | | RootFS data (starting with "hsqs") + |
| 0x420000 | 68 73 71 73 … | zero padding to "Length" |
+--------------+---------------+----------------------------------------+
| | | Some signature data (format is |
| | | unknown). Necessary for the fw |
| "Lenght" | 00 00 00 00 … | update via oem fw web interface. |
+--------------+---------------+----------------------------------------+
| "Lenght" + | | TRX magic "HDR0". U-Boot is |
| 0x10c | 48 44 52 30 | checking it at every boot. |
+--------------+---------------+----------------------------------------+
| | | 1.00: |
| | | Zero padding to ("Lenght" + 0x23000) |
| | | 1.0.12: |
| | | Zero padding to ("Lenght" + 0x2a000) |
| "Lenght" + | | 1.0.13, 1.0.15, 1.0.16: |
| 0x110 | 00 00 00 00 | Zero padding to ("Lenght" + 0x10000) |
+--------------+---------------+----------------------------------------+
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
|
||
Michael Pratt
|
41be1a2de2 |
ath79: add support for Araknis AN-700-AP-I-AC
FCC ID: 2AG6R-AN700APIAC
Araknis AN-700-AP-I-AC is an indoor wireless access point with
1 Gb ethernet port, dual-band wireless,
internal antenna plates, and 802.3at PoE+
this board is a Senao device:
the hardware is equivalent to EnGenius EAP1750
the software is modified Senao SDK which is based on openwrt and uboot
including image checksum verification at boot time,
and a failsafe image that boots if checksum fails
**Specification:**
- QCA9558 SOC MIPS 74kc, 2.4 GHz WMAC, 3x3
- QCA9880 WLAN PCI card, 5 GHz, 3x3, 26dBm
- AR8035-A PHY RGMII GbE with PoE+ IN
- 40 MHz clock
- 16 MB FLASH MX25L12845EMI-10G
- 2x 64 MB RAM NT5TU32M16
- UART console J10, populated, RX shorted to ground
- 4 antennas 5 dBi, internal omni-directional plates
- 4 LEDs power, 2G, 5G, wps
- 1 button reset
NOTE: all 4 gpio controlled LEDS are viewed through the same lightguide
therefore, the power LED is off for default state
**MAC addresses:**
MAC address labeled as ETH
Only one Vendor MAC address in flash at art 0x0
eth0 ETH *:xb art 0x0
phy1 2.4G *:xc ---
phy0 5GHz *:xd ---
**Serial Access:**
the RX line on the board for UART is shorted to ground by resistor R176
therefore it must be removed to use the console
but it is not necessary to remove to view boot log
optionally, R175 can be replaced with a solder bridge short
the resistors R175 and R176 are next to the UART RX pin at J10
**Installation:**
Method 1: Firmware upgrade page:
(if you cannot access the APs webpage)
factory reset with the reset button
connect ethernet to a computer
OEM webpage at 192.168.20.253
username and password 'araknis'
make a new password, login again...
Navigate to 'File Management' page from left pane
Click Browse and select the factory.bin image
Upload and verify checksum
Click Continue to confirm
wait about 3 minutes
Method 2: Serial to load Failsafe webpage:
After connecting to serial console and rebooting...
Interrupt uboot with any key pressed rapidly
execute `run failsafe_boot` OR `bootm 0x9fd70000`
wait a minute
connect to ethernet and navigate to
192.168.20.253
Select the factory.bin image and upload
wait about 3 minutes
**Return to OEM:**
Method 1: Serial to load Failsafe webpage (above)
Method 2: delete a checksum from uboot-env
this will make uboot load the failsafe image at next boot
because it will fail the checksum verification of the image
ssh into openwrt and run
`fw_setenv rootfs_checksum 0`
reboot, wait a minute
connect to ethernet and navigate to
192.168.20.253
select OEM firmware image and click upgrade
Method 3: backup mtd partitions before upgrade
**TFTP recovery:**
Requires serial console, reset button does nothing
rename initramfs-kernel.bin to '0101A8C0.img'
make available on TFTP server at 192.168.1.101
power board, interrupt boot with serial console
execute `tftpboot` and `bootm 0x81000000`
NOTE: TFTP may not be reliable due to bugged bootloader
set MTU to 600 and try many times
**Format of OEM firmware image:**
The OEM software is built using SDKs from Senao
which is based on a heavily modified version
of Openwrt Kamikaze or Altitude Adjustment.
One of the many modifications is sysupgrade being performed by a custom script.
Images are verified through successful unpackaging, correct filenames
and size requirements for both kernel and rootfs files, and that they
start with the correct magic numbers (first 2 bytes) for the respective headers.
Newer Senao software requires more checks but their script
includes a way to skip them.
The OEM upgrade script is at
/etc/fwupgrade.sh
OKLI kernel loader is required because the OEM software
expects the kernel to be less than 1536k
and the OEM upgrade procedure would otherwise
overwrite part of the kernel when writing rootfs.
Note on PLL-data cells:
The default PLL register values will not work
because of the external AR8035 switch between
the SOC and the ethernet port.
For QCA955x series, the PLL registers for eth0 and eth1
can be see in the DTSI as 0x28 and 0x48 respectively.
Therefore the PLL registers can be read from uboot
for each link speed after attempting tftpboot
or another network action using that link speed
with `md 0x18050028 1` and `md 0x18050048 1`.
The clock delay required for RGMII can be applied at the PHY side,
using the at803x driver `phy-mode` setting through the DTS.
Therefore, the Ethernet Configuration registers for GMAC0
do not need the bits for RGMII delay on the MAC side.
This is possible due to fixes in at803x driver
since Linux 5.1 and 5.3
Signed-off-by: Michael Pratt <mcpratt@pm.me>
|
||
|
Michael Pratt
|
56716b578e |
ath79: add support for Araknis AN-500-AP-I-AC
FCC ID: 2AG6R-AN500APIAC
Araknis AN-500-AP-I-AC is an indoor wireless access point with
1 Gb ethernet port, dual-band wireless,
internal antenna plates, and 802.3at PoE+
this board is a Senao device:
the hardware is equivalent to EnGenius EAP1200
the software is modified Senao SDK which is based on openwrt and uboot
including image checksum verification at boot time,
and a failsafe image that boots if checksum fails
**Specification:**
- QCA9557 SOC MIPS 74kc, 2.4 GHz WMAC, 2x2
- QCA9882 WLAN PCI card 168c:003c, 5 GHz, 2x2, 26dBm
- AR8035-A PHY RGMII GbE with PoE+ IN
- 40 MHz clock
- 16 MB FLASH MX25L12845EMI-10G
- 2x 64 MB RAM NT5TU32M16
- UART console J10, populated, RX shorted to ground
- 4 antennas 5 dBi, internal omni-directional plates
- 4 LEDs power, 2G, 5G, wps
- 1 button reset
NOTE: all 4 gpio controlled LEDS are viewed through the same lightguide
therefore, the power LED is off for default state
**MAC addresses:**
MAC address labeled as ETH
Only one Vendor MAC address in flash at art 0x0
eth0 ETH *:e1 art 0x0
phy1 2.4G *:e2 ---
phy0 5GHz *:e3 ---
**Serial Access:**
the RX line on the board for UART is shorted to ground by resistor R176
therefore it must be removed to use the console
but it is not necessary to remove to view boot log
optionally, R175 can be replaced with a solder bridge short
the resistors R175 and R176 are next to the UART RX pin at J10
**Installation:**
Method 1: Firmware upgrade page:
(if you cannot access the APs webpage)
factory reset with the reset button
connect ethernet to a computer
OEM webpage at 192.168.20.253
username and password 'araknis'
make a new password, login again...
Navigate to 'File Management' page from left pane
Click Browse and select the factory.bin image
Upload and verify checksum
Click Continue to confirm
wait about 3 minutes
Method 2: Serial to load Failsafe webpage:
After connecting to serial console and rebooting...
Interrupt uboot with any key pressed rapidly
execute `run failsafe_boot` OR `bootm 0x9fd70000`
wait a minute
connect to ethernet and navigate to
192.168.20.253
Select the factory.bin image and upload
wait about 3 minutes
**Return to OEM:**
Method 1: Serial to load Failsafe webpage (above)
Method 2: delete a checksum from uboot-env
this will make uboot load the failsafe image at next boot
because it will fail the checksum verification of the image
ssh into openwrt and run
`fw_setenv rootfs_checksum 0`
reboot, wait a minute
connect to ethernet and navigate to
192.168.20.253
select OEM firmware image and click upgrade
Method 3: backup mtd partitions before upgrade
**TFTP recovery:**
Requires serial console, reset button does nothing
rename initramfs-kernel.bin to '0101A8C0.img'
make available on TFTP server at 192.168.1.101
power board, interrupt boot with serial console
execute `tftpboot` and `bootm 0x81000000`
NOTE: TFTP may not be reliable due to bugged bootloader
set MTU to 600 and try many times
**Format of OEM firmware image:**
The OEM software is built using SDKs from Senao
which is based on a heavily modified version
of Openwrt Kamikaze or Altitude Adjustment.
One of the many modifications is sysupgrade being performed by a custom script.
Images are verified through successful unpackaging, correct filenames
and size requirements for both kernel and rootfs files, and that they
start with the correct magic numbers (first 2 bytes) for the respective headers.
Newer Senao software requires more checks but their script
includes a way to skip them.
The OEM upgrade script is at
/etc/fwupgrade.sh
OKLI kernel loader is required because the OEM software
expects the kernel to be less than 1536k
and the OEM upgrade procedure would otherwise
overwrite part of the kernel when writing rootfs.
Note on PLL-data cells:
The default PLL register values will not work
because of the external AR8035 switch between
the SOC and the ethernet port.
For QCA955x series, the PLL registers for eth0 and eth1
can be see in the DTSI as 0x28 and 0x48 respectively.
Therefore the PLL registers can be read from uboot
for each link speed after attempting tftpboot
or another network action using that link speed
with `md 0x18050028 1` and `md 0x18050048 1`.
The clock delay required for RGMII can be applied at the PHY side,
using the at803x driver `phy-mode` setting through the DTS.
Therefore, the Ethernet Configuration registers for GMAC0
do not need the bits for RGMII delay on the MAC side.
This is possible due to fixes in at803x driver
since Linux 5.1 and 5.3
Signed-off-by: Michael Pratt <mcpratt@pm.me>
|
||
|
Michael Pratt
|
561f46bd02 |
ath79: add support for Araknis AN-300-AP-I-N
FCC ID: U2M-AN300APIN
Araknis AN-300-AP-I-N is an indoor wireless access point with
1 Gb ethernet port, dual-band wireless,
internal antenna plates, and 802.3at PoE+
this board is a Senao device:
the hardware is equivalent to EnGenius EWS310AP
the software is modified Senao SDK which is based on openwrt and uboot
including image checksum verification at boot time,
and a failsafe image that boots if checksum fails
**Specification:**
- AR9344 SOC MIPS 74kc, 2.4 GHz WMAC, 2x2
- AR9382 WLAN PCI on-board 168c:0030, 5 GHz, 2x2
- AR8035-A PHY RGMII GbE with PoE+ IN
- 40 MHz clock
- 16 MB FLASH MX25L12845EMI-10G
- 2x 64 MB RAM 1839ZFG V59C1512164QFJ25
- UART console J10, populated, RX shorted to ground
- 4 antennas 5 dBi, internal omni-directional plates
- 4 LEDs power, 2G, 5G, wps
- 1 button reset
NOTE: all 4 gpio controlled LEDS are viewed through the same lightguide
therefore, the power LED is off for default state
**MAC addresses:**
MAC address labeled as ETH
Only one Vendor MAC address in flash at art 0x0
eth0 ETH *:7d art 0x0
phy1 2.4G *:7e ---
phy0 5GHz *:7f ---
**Serial Access:**
the RX line on the board for UART is shorted to ground by resistor R176
therefore it must be removed to use the console
but it is not necessary to remove to view boot log
optionally, R175 can be replaced with a solder bridge short
the resistors R175 and R176 are next to the UART RX pin at J10
**Installation:**
Method 1: Firmware upgrade page:
(if you cannot access the APs webpage)
factory reset with the reset button
connect ethernet to a computer
OEM webpage at 192.168.20.253
username and password 'araknis'
make a new password, login again...
Navigate to 'File Management' page from left pane
Click Browse and select the factory.bin image
Upload and verify checksum
Click Continue to confirm
wait about 3 minutes
Method 2: Serial to load Failsafe webpage:
After connecting to serial console and rebooting...
Interrupt uboot with any key pressed rapidly
execute `run failsafe_boot` OR `bootm 0x9fd70000`
wait a minute
connect to ethernet and navigate to
192.168.20.253
Select the factory.bin image and upload
wait about 3 minutes
**Return to OEM:**
Method 1: Serial to load Failsafe webpage (above)
Method 2: delete a checksum from uboot-env
this will make uboot load the failsafe image at next boot
because it will fail the checksum verification of the image
ssh into openwrt and run
`fw_setenv rootfs_checksum 0`
reboot, wait a minute
connect to ethernet and navigate to
192.168.20.253
select OEM firmware image and click upgrade
Method 3: backup mtd partitions before upgrade
**TFTP recovery:**
Requires serial console, reset button does nothing
rename initramfs-kernel.bin to '0101A8C0.img'
make available on TFTP server at 192.168.1.101
power board, interrupt boot with serial console
execute `tftpboot` and `bootm 0x81000000`
NOTE: TFTP may not be reliable due to bugged bootloader
set MTU to 600 and try many times
**Format of OEM firmware image:**
The OEM software is built using SDKs from Senao
which is based on a heavily modified version
of Openwrt Kamikaze or Altitude Adjustment.
One of the many modifications is sysupgrade being performed by a custom script.
Images are verified through successful unpackaging, correct filenames
and size requirements for both kernel and rootfs files, and that they
start with the correct magic numbers (first 2 bytes) for the respective headers.
Newer Senao software requires more checks but their script
includes a way to skip them.
The OEM upgrade script is at
/etc/fwupgrade.sh
OKLI kernel loader is required because the OEM software
expects the kernel to be less than 1536k
and the OEM upgrade procedure would otherwise
overwrite part of the kernel when writing rootfs.
Note on PLL-data cells:
The default PLL register values will not work
because of the external AR8035 switch between
the SOC and the ethernet port.
For QCA955x series, the PLL registers for eth0 and eth1
can be see in the DTSI as 0x28 and 0x48 respectively.
Therefore the PLL registers can be read from uboot
for each link speed after attempting tftpboot
or another network action using that link speed
with `md 0x18050028 1` and `md 0x18050048 1`.
The clock delay required for RGMII can be applied at the PHY side,
using the at803x driver `phy-mode` setting through the DTS.
Therefore, the Ethernet Configuration registers for GMAC0
do not need the bits for RGMII delay on the MAC side.
This is possible due to fixes in at803x driver
since Linux 5.1 and 5.3
Signed-off-by: Michael Pratt <mcpratt@pm.me>
|
||
|
Martin Kennedy
|
d1a8690742 |
realtek: add ZyXEL GS1900-24 v1 support
The ZyXEL GS1900-24 v1 is a 24 port switch with two SFP ports, similar to
the other GS1900 switches.
Specifications
--------------
* Device: ZyXEL GS1900-24 v1
* SoC: Realtek RTL8382M 500 MHz MIPS 4KEc
* Flash: 16 MiB
* RAM: Winbond W9751G8KB-25 64 MiB DDR2 SDRAM
* Ethernet: 24x 10/100/1000 Mbps, 2x SFP 100/1000 Mbps
* LEDs:
* 1 PWR LED (green, not configurable)
* 1 SYS LED (green, configurable)
* 24 ethernet port link/activity LEDs (green, SoC controlled)
* 2 SFP status/activity LEDs (green, SoC controlled)
* Buttons:
* 1 "RESET" button on front panel (soft reset)
* 1 button ('SW1') behind right hex grate (hardwired power-off)
* Power: 120-240V AC C13
* UART: Internal populated 10-pin header ('J5') providing RS232;
connected to SoC UART through a SIPEX 3232EC for voltage
level shifting.
* 'J5' RS232 Pinout (dot as pin 1):
2) SoC RXD
3) GND
10) SoC TXD
Serial connection parameters: 115200 8N1.
Installation
------------
OEM upgrade method:
* Log in to OEM management web interface
* Navigate to Maintenance > Firmware > Management
* If "Active Image" has the first option selected, OpenWrt will need to be
flashed to the "Active" partition. If the second option is selected,
OpenWrt will need to be flashed to the "Backup" partition.
* Navigate to Maintenance > Firmware > Upload
* Upload the openwrt-realtek-rtl838x-zyxel_gs1900-24-v1-initramfs-kernel.bin
file by your preferred method to the previously determined partition.
When prompted, select to boot from the newly flashed image, and reboot
the switch.
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade /tmp/openwrt-realtek-rtl838x-zyxel_gs1900-24-v1-squashfs-sysupgrade.bin
U-Boot TFTP method:
* Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10).
* Set up a TFTP server on your client and make it serve the initramfs
image.
* Connect serial, power up the switch, interrupt U-boot by hitting the
space bar, and enable the network:
> rtk network on
> Since the GS1900-24 v1 is a dual-partition device, you want to keep the
OEM firmware on the backup partition for the time being. OpenWrt can
only be installed in the first partition anyway (hardcoded in the
DTS). To ensure we are set to boot from the first partition, issue the
following commands:
> setsys bootpartition 0
> savesys
* Download the image onto the device and boot from it:
> tftpboot 0x81f00000 192.168.1.10:openwrt-realtek-rtl838x-zyxel_gs1900-24-v1-initramfs-kernel.bin
> bootm
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade /tmp/openwrt-realtek-rtl838x-zyxel_gs1900-24-v1-squashfs-sysupgrade.bin
Signed-off-by: Martin Kennedy <hurricos@gmail.com>
|
||
INAGAKI Hiroshi
|
98113220fa |
uboot-envtools: add support for I-O DATA BSH-G24MB
This patch adds the device-specific configuration to u-boot-envtools for I-O DATA BSH-G24MB switch. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> |
||
Langhua Ye
|
d15f9b9043 |
uboot-envtools: mt7622: add support for Ruijie RG-EW3200GX PRO
Add U-Boot environment settings for Ruijie RG-EW3200GX PRO to allow users to access the bootloader environment using fw_printenv/fw_setenv while running OpenWrt. Signed-off-by: Langhua Ye <y1248289414@outlook.com> |
||
Piotr Dymacz
|
2d5b596b49 |
uboot-envtools: ath79: add support for ALFA Network Tube-2HQ
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com> |
||
Lech Perczak
|
7ac8da0060 |
ath79: support ZTE MF286A/R
ZTE MF286A and MF286R are indoor LTE category 6/7 CPE router with simultaneous dual-band 802.11ac plus 802.11n Wi-Fi radios and quad-port gigabit Ethernet switch, FXS and external USB 2.0 port. Hardware highlights: - CPU: QCA9563 SoC at 775MHz, - RAM: 128MB DDR2, - NOR Flash: MX25L1606E 2MB SPI Flash, for U-boot only, - NAND Flash: W25N01GV 128MB SPI NAND-Flash, for all other data, - Wi-Fi 5GHz: QCA9886 2x2 MIMO 802.11ac Wave2 radio, - WI-Fi 2.4GHz: QCA9563 3x3 MIMO 802.11n radio, - Switch: QCA8337v2 4-port gigabit Ethernet, with single SGMII CPU port, - WWAN: [MF286A] MDM9230-based category 6 internal LTE modem [MF286R] PXA1826-based category 7 internal LTE modem in extended mini-PCIE form factor, with 3 internal antennas and 2 external antenna connections, single mini-SIM slot. - FXS: one external ATA port (handled entirely by modem part) with two physical connections in parallel, - USB: Single external USB 2.0 port, - Switches: power switch, WPS, Wi-Fi and reset buttons, - LEDs: Wi-Fi, Test (internal). Rest of LEDs (Phone, WWAN, Battery, Signal state) handled entirely by modem. 4 link status LEDs handled by the switch on the backside. - Battery: 3Ah 1-cell Li-Ion replaceable battery, with charging and monitoring handled by modem. - Label MAC device: eth0 The device shares many components with previous model, MF286, differing mostly by a Wave2 5GHz radio, flash layout and internal LED color. In case of MF286A, the modem is the same as in MF286. MF286R uses a different modem based on Marvell PXA1826 chip. Internal modem of MF286A is supported via uqmi, MF286R modem isn't fully supported, but it is expected to use comgt-ncm for connection, as it uses standard 3GPP AT commands for connection establishment. Console connection: connector X2 is the console port, with the following pinout, starting from pin 1, which is the topmost pin when the board is upright: - VCC (3.3V). Do not use unless you need to source power for the converer from it. - TX - RX - GND Default port configuration in U-boot as well as in stock firmware is 115200-8-N-1. Installation: Due to different flash layout from stock firmware, sysupgrade from within stock firmware is impossible, despite it's based on QSDK which itself is based on OpenWrt. STEP 0: Stock firmware update: As installing OpenWrt cuts you off from official firmware updates for the modem part, it is recommended to update the stock firmware to latest version before installation, to have built-in modem at the latest firmware version. STEP 1: gaining root shell: Method 1: This works if busybox has telnetd compiled in the binary. If this does not work, try method 2. Using well-known exploit to start telnetd on your router - works only if Busybox on stock firmware has telnetd included: - Open stock firmware web interface - Navigate to "URL filtering" section by going to "Advanced settings", then "Firewall" and finally "URL filter". - Add an entry ending with "&&telnetd&&", for example "http://hostname/&&telnetd&&". - telnetd will immediately listen on port 4719. - After connecting to telnetd use "admin/admin" as credentials. Method 2: This works if busybox does not have telnetd compiled in. Notably, this is the case in DNA.fi firmware. If this does not work, try method 3. - Set IP of your computer to 192.168.0.22. (or appropriate subnet if changed) - Have a TFTP server running at that address - Download MIPS build of busybox including telnetd, for example from: https://busybox.net/downloads/binaries/1.21.1/busybox-mips and put it in it's root directory. Rename it as "telnetd". - As previously, login to router's web UI and navigate to "URL filtering" - Using "Inspect" feature, extend "maxlength" property of the input field named "addURLFilter", so it looks like this: <input type="text" name="addURLFilter" id="addURLFilter" maxlength="332" class="required form-control"> - Stay on the page - do not navigate anywhere - Enter "http://aa&zte_debug.sh 192.168.0.22 telnetd" as a filter. - Save the settings. This will download the telnetd binary over tftp and execute it. You should be able to log in at port 23, using "admin/admin" as credentials. Method 3: If the above doesn't work, use the serial console - it exposes root shell directly without need for login. Some stock firmwares, notably one from finnish DNA operator lack telnetd in their builds. STEP 2: Backing up original software: As the stock firmware may be customized by the carrier and is not officially available in the Internet, IT IS IMPERATIVE to back up the stock firmware, if you ever plan to returning to stock firmware. It is highly recommended to perform backup using both methods, to avoid hassle of reassembling firmware images in future, if a restore is needed. Method 1: after booting OpenWrt initramfs image via TFTP: PLEASE NOTE: YOU CANNOT DO THIS IF USING INTERMEDIATE FIRMWARE FOR INSTALLATION. - Dump stock firmware located on stock kernel and ubi partitions: ssh root@192.168.1.1: cat /dev/mtd4 > mtd4_kernel.bin ssh root@192.168.1.1: cat /dev/mtd9 > mtd9_ubi.bin And keep them in a safe place, should a restore be needed in future. Method 2: using stock firmware: - Connect an external USB drive formatted with FAT or ext4 to the USB port. - The drive will be auto-mounted to /var/usb_disk - Check the flash layout of the device: cat /proc/mtd It should show the following: mtd0: 000a0000 00010000 "u-boot" mtd1: 00020000 00010000 "u-boot-env" mtd2: 00140000 00010000 "reserved1" mtd3: 000a0000 00020000 "fota-flag" mtd4: 00080000 00020000 "art" mtd5: 00080000 00020000 "mac" mtd6: 000c0000 00020000 "reserved2" mtd7: 00400000 00020000 "cfg-param" mtd8: 00400000 00020000 "log" mtd9: 000a0000 00020000 "oops" mtd10: 00500000 00020000 "reserved3" mtd11: 00800000 00020000 "web" mtd12: 00300000 00020000 "kernel" mtd13: 01a00000 00020000 "rootfs" mtd14: 01900000 00020000 "data" mtd15: 03200000 00020000 "fota" mtd16: 01d00000 00020000 "firmware" Differences might indicate that this is NOT a MF286A device but one of other variants. - Copy over all MTD partitions, for example by executing the following: for i in 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15; do cat /dev/mtd$i > \ /var/usb_disk/mtd$i; done "Firmware" partition can be skipped, it is a concatenation of "kernel" and "rootfs". - If the count of MTD partitions is different, this might indicate that this is not a MF286A device, but one of its other variants. - (optionally) rename the files according to MTD partition names from /proc/mtd - Unmount the filesystem: umount /var/usb_disk; sync and then remove the drive. - Store the files in safe place if you ever plan to return to stock firmware. This is especially important, because stock firmware for this device is not available officially, and is usually customized by the mobile providers. STEP 3: Booting initramfs image: Method 1: using serial console (RECOMMENDED): - Have TFTP server running, exposing the OpenWrt initramfs image, and set your computer's IP address as 192.168.0.22. This is the default expected by U-boot. You may wish to change that, and alter later commands accordingly. - Connect the serial console if you haven't done so already, - Interrupt boot sequence by pressing any key in U-boot when prompted - Use the following commands to boot OpenWrt initramfs through TFTP: setenv serverip 192.168.0.22 setenv ipaddr 192.168.0.1 tftpboot 0x81000000 openwrt-ath79-nand-zte_mf286a-initramfs-kernel.bin bootm 0x81000000 (Replace server IP and router IP as needed). There is no emergency TFTP boot sequence triggered by buttons, contrary to MF283+. - When OpenWrt initramfs finishes booting, proceed to actual installation. Method 2: using initramfs image as temporary boot kernel This exploits the fact, that kernel and rootfs MTD devices are consecutive on NAND flash, so from within stock image, an initramfs can be written to this area and booted by U-boot on next reboot, because it uses "nboot" command which isn't limited by kernel partition size. - Download the initramfs-kernel.bin image - After backing up the previous MTD contents, write the images to the "firmware" MTD device, which conveniently concatenates "kernel" and "rootfs" partitions that can fit the initramfs image: nandwrite -p /dev/<firmware-mtd> \ /var/usb_disk/openwrt-ath79-zte_mf286a-initramfs-kernel.bin - If write is OK, reboot the device, it will reboot to OpenWrt initramfs: reboot -f - After rebooting, SSH into the device and use sysupgrade to perform proper installation. Method 3: using built-in TFTP recovery (LAST RESORT): - With that method, ensure you have complete backup of system's NAND flash first. It involves deliberately erasing the kernel. - Download "-initramfs-kernel.bin" image for the device. - Prepare the recovery image by prepending 8MB of zeroes to the image, and name it root_uImage: dd if=/dev/zero of=padding.bin bs=8M count=1 cat padding.bin openwrt-ath79-nand-zte_mf286a-initramfs-kernel.bin > root_uImage - Set up a TFTP server at 192.0.0.1/8. Router will use random address from that range. - Put the previously generated "root_uImage" into TFTP server root directory. - Deliberately erase "kernel" partition" using stock firmware after taking backup. THIS IS POINT OF NO RETURN. - Restart the device. U-boot will attempt flashing the recovery initramfs image, which will let you perform actual installation using sysupgrade. This might take a considerable time, sometimes the router doesn't establish Ethernet link properly right after booting. Be patient. - After U-boot finishes flashing, the LEDs of switch ports will all light up. At this moment, perform power-on reset, and wait for OpenWrt initramfs to finish booting. Then proceed to actual installation. STEP 4: Actual installation: - Set your computer IP to 192.168.1.22/24 - scp the sysupgrade image to the device: scp openwrt-ath79-nand-zte_mf286a-squashfs-sysupgrade.bin \ root@192.168.1.1:/tmp/ - ssh into the device and execute sysupgrade: sysupgrade -n /tmp/openwrt-ath79-nand-zte_mf286a-squashfs-sysupgrade.bin - Wait for router to reboot to full OpenWrt. STEP 5: WAN connection establishment Since the router is equipped with LTE modem as its main WAN interface, it might be useful to connect to the Internet right away after installation. To do so, please put the following entries in /etc/config/network, replacing the specific configuration entries with one needed for your ISP: config interface 'wan' option proto 'qmi' option device '/dev/cdc-wdm0' option auth '<auth>' # As required, usually 'none' option pincode '<pin>' # If required by SIM option apn '<apn>' # As required by ISP option pdptype '<pdp>' # Typically 'ipv4', or 'ipv4v6' or 'ipv6' For example, the following works for most polish ISPs config interface 'wan' option proto 'qmi' option device '/dev/cdc-wdm0' option auth 'none' option apn 'internet' option pdptype 'ipv4' The required minimum is: config interface 'wan' option proto 'qmi' option device '/dev/cdc-wdm0' In this case, the modem will use last configured APN from stock firmware - this should work out of the box, unless your SIM requires PIN which can't be switched off. If you have build with LuCI, installing luci-proto-qmi helps with this task. Restoring the stock firmware: Preparation: If you took your backup using stock firmware, you will need to reassemble the partitions into images to be restored onto the flash. The layout might differ from ISP to ISP, this example is based on generic stock firmware The only partitions you really care about are "web", "kernel", and "rootfs". These are required to restore the stock firmware through factory TFTP recovery. Because kernel partition was enlarged, compared to stock firmware, the kernel and rootfs MTDs don't align anymore, and you need to carve out required data if you only have backup from stock FW: - Prepare kernel image cat mtd12_kernel.bin mtd13_rootfs.bin > owrt_kernel.bin truncate -s 4M owrt_kernel_restore.bin - Cut off first 1MB from rootfs dd if=mtd13_rootfs.bin of=owrt_rootfs.bin bs=1M skip=1 - Prepare image to write to "ubi" meta-partition: cat mtd6_reserved2.bi mtd7_cfg-param.bin mtd8_log.bin mtd9_oops.bin \ mtd10_reserved3.bin mtd11_web.bin owrt_rootfs.bin > \ owrt_ubi_ubi_restore.bin You can skip the "fota" partition altogether, it is used only for stock firmware update purposes and can be overwritten safely anyway. The same is true for "data" partition which on my device was found to be unused at all. Restoring mtd5_cfg-param.bin will restore the stock firmware configuration you had before. Method 1: Using initramfs: This method is recmmended if you took your backup from within OpenWrt initramfs, as the reassembly is not needed. - Boot to initramfs as in step 3: - Completely detach ubi0 partition using ubidetach /dev/ubi0_0 - Look up the kernel and ubi partitions in /proc/mtd - Copy over the stock kernel image using scp to /tmp - Erase kernel and restore stock kernel: (scp mtd4_kernel.bin root@192.168.1.1:/tmp/) mtd write <kernel_mtd> mtd4_kernel.bin rm mtd4_kernel.bin - Copy over the stock partition backups one-by-one using scp to /tmp, and restore them individually. Otherwise you might run out of space in tmpfs: (scp mtd3_ubiconcat0.bin root@192.168.1.1:/tmp/) mtd write <ubiconcat0_mtd> mtd3_ubiconcat0.bin rm mtd3_ubiconcat0.bin (scp mtd5_ubiconcat1.bin root@192.168.1.1:/tmp/) mtd write <ubiconcat1_mtd> mtd5_ubiconcat1.bin rm mtd5_ubiconcat1.bin - If the write was correct, force a device reboot with reboot -f Method 2: Using live OpenWrt system (NOT RECOMMENDED): - Prepare a USB flash drive contatining MTD backup files - Ensure you have kmod-usb-storage and filesystem driver installed for your drive - Mount your flash drive mkdir /tmp/usb mount /dev/sda1 /tmp/usb - Remount your UBI volume at /overlay to R/O mount -o remount,ro /overlay - Write back the kernel and ubi partitions from USB drive cd /tmp/usb mtd write mtd4_kernel.bin /dev/<kernel_mtd> mtd write mtd9_ubi.bin /dev/<kernel_ubi> - If everything went well, force a device reboot with reboot -f Last image may be truncated a bit due to lack of space in RAM, but this will happen over "fota" MTD partition which may be safely erased after reboot anyway. Method 3: using built-in TFTP recovery: This method is recommended if you took backups using stock firmware. - Assemble a recovery rootfs image from backup of stock partitions by concatenating "web", "kernel", "rootfs" images dumped from the device, as "root_uImage" - Use it in place of "root_uImage" recovery initramfs image as in the TFTP pre-installation method. Quirks and known issuesa - It was observed, that CH340-based USB-UART converters output garbage during U-boot phase of system boot. At least CP2102 is known to work properly. - Kernel partition size is increased to 4MB compared to stock 3MB, to accomodate future kernel updates - at this moment OpenWrt 5.10 kernel image is at 2.5MB which is dangerously close to the limit. This has no effect on booting the system - but keep that in mind when reassembling an image to restore stock firmware. - uqmi seems to be unable to change APN manually, so please use the one you used before in stock firmware first. If you need to change it, please use protocok '3g' to establish connection once, or use the following command to change APN (and optionally IP type) manually: echo -ne 'AT+CGDCONT=1,"IP","<apn>' > /dev/ttyUSB0 - The only usable LED as a "system LED" is the blue debug LED hidden inside the case. All other LEDs are controlled by modem, on which the router part has some influence only on Wi-Fi LED. - Wi-Fi LED currently doesn't work while under OpenWrt, despite having correct GPIO mapping. All other LEDs are controlled by modem, including this one in stock firmware. GPIO19, mapped there only acts as a gate, while the actual signal source seems to be 5GHz Wi-Fi radio, however it seems it is not the LED exposed by ath10k as ath10k-phy0. - GPIO5 used for modem reset is a suicide switch, causing a hardware reset of whole board, not only the modem. It is attached to gpio-restart driver, to restart the modem on reboot as well, to ensure QMI connectivity after reboot, which tends to fail otherwise. - Modem, as in MF283+, exposes root shell over ADB - while not needed for OpenWrt operation at all - have fun lurking around. The same modem module is used as in older MF286. Signed-off-by: Lech Perczak <lech.perczak@gmail.com> |
||
|
Lech Perczak
|
411940ded4 |
ath79: uboot-envtools: fix partition for ZTE MF286
By mistake, a wrong partition for U-boot environment was introduced for
ZTE MF286 while adding support, when flash layout wasn't finalized. Fix
that, according to the actual flash layout:
dev: size erasesize name
mtd0: 00140000 00020000 "fota-flag"
mtd1: 00140000 00020000 "caldata"
mtd2: 00140000 00020000 "mac"
mtd3: 00f40000 00020000 "ubiconcat0"
mtd4: 00400000 00020000 "kernel"
mtd5: 06900000 00020000 "ubiconcat1"
mtd6: 00080000 00010000 "u-boot"
mtd7: 00020000 00010000 "u-boot-env"
mtd8: 07840000 00020000 "ubi"
Fixes:
|
||
|
Martin Kennedy
|
cfe79f2eb8 |
mpc85xx: Patch HiveAP 330 u-boot to fix boot
When Kernel 5.10 was enabled for mpc85xx, the kernel once again became too large upon decompression (>7MB or so) to decompress itself on boot (see FS#4110[1]). There have been many attempts to fix booting from a compressed kernel on the HiveAP-330: - |
||
Raymond Wang
|
3343ca7e68 |
ramips: add support for Xiaomi Mi Router CR660x series
Xiaomi Mi Router CR6606 is a Wi-Fi6 AX1800 Router with 4 GbE Ports.
Alongside the general model, it has three carrier customized models:
CR6606 (China Unicom), CR6608 (China Mobile), CR6609 (China Telecom)
Specifications:
- SoC: MediaTek MT7621AT
- RAM: 256MB DDR3 (ESMT M15T2G16128A)
- Flash: 128MB NAND (ESMT F59L1G81MB)
- Ethernet: 1000Base-T x4 (MT7530 SoC)
- WLAN: 2x2 2.4GHz 574Mbps + 2x2 5GHz 1201Mbps (MT7905DAN + MT7975DN)
- LEDs: System (Blue, Yellow), Internet (Blue, Yellow)
- Buttons: Reset, WPS
- UART: through-hole on PCB ([VCC 3.3v](RX)(GND)(TX) 115200, 8n1)
- Power: 12VDC, 1A
Jailbreak Notes:
1. Get shell access.
1.1. Get yourself a wireless router that runs OpenWrt already.
1.2. On the OpenWrt router:
1.2.1. Access its console.
1.2.2. Create and edit
/usr/lib/lua/luci/controller/admin/xqsystem.lua
with the following code (exclude backquotes and line no.):
```
1 module("luci.controller.admin.xqsystem", package.seeall)
2
3 function index()
4 local page = node("api")
5 page.target = firstchild()
6 page.title = ("")
7 page.order = 100
8 page.index = true
9 page = node("api","xqsystem")
10 page.target = firstchild()
11 page.title = ("")
12 page.order = 100
13 page.index = true
14 entry({"api", "xqsystem", "token"}, call("getToken"), (""),
103, 0x08)
15 end
16
17 local LuciHttp = require("luci.http")
18
19 function getToken()
20 local result = {}
21 result["code"] = 0
22 result["token"] = "; nvram set ssh_en=1; nvram commit; sed -i
's/channel=.*/channel=\"debug\"/g' /etc/init.d/dropbear; /etc/init.d/drop
bear start;"
23 LuciHttp.write_json(result)
24 end
```
1.2.3. Browse http://{OWRT_ADDR}/cgi-bin/luci/api/xqsystem/token
It should give you a respond like this:
{"code":0,"token":"; nvram set ssh_en=1; nvram commit; ..."}
If so, continue; Otherwise, check the file, reboot the rout-
er, try again.
1.2.4. Set wireless network interface's IP to 169.254.31.1, turn
off DHCP of wireless interface's zone.
1.2.5. Connect to the router wirelessly, manually set your access
device's IP to 169.254.31.3, make sure
http://169.254.31.1/cgi-bin/luci/api/xqsystem/token
still have a similar result as 1.2.3 shows.
1.3. On the Xiaomi CR660x:
1.3.1. Login to the web interface. Your would be directed to a
page with URL like this:
http://{ROUTER_ADDR}/cgi-bin/luci/;stok={STOK}/web/home#r-
outer
1.3.2. Browse this URL with {STOK} from 1.3.1, {WIFI_NAME}
{PASSWORD} be your OpenWrt router's SSID and password:
http://{MIROUTER_ADDR}/cgi-bin/luci/;stok={STOK}/api/misy-
stem/extendwifi_connect?ssid={WIFI_NAME}&password={PASSWO-
RD}
It should return 0.
1.3.3. Browse this URL with {STOK} from 1.3.1:
http://{MIROUTER_ADDR}/cgi-bin/luci/;stok={STOK}/api/xqsy-
stem/oneclick_get_remote_token?username=xxx&password=xxx&-
nonce=xxx
1.4. Before rebooting, you can now access your CR660x via SSH.
For CR6606, you can calculate your root password by this project:
https://github.com/wfjsw/xiaoqiang-root-password, or at
https://www.oxygen7.cn/miwifi.
The root password for carrier-specific models should be the admi-
nistration password or the default login password on the label.
It is also feasible to change the root password at the same time
by modifying the script from step 1.2.2.
You can treat OpenWrt Router however you like from this point as
long as you don't mind go through this again if you have to expl-
oit it again. If you do have to and left your OpenWrt router unt-
ouched, start from 1.3.
2. There's no official binary firmware available, and if you lose the
content of your flash, no one except Xiaomi can help you.
Dump these partitions in case you need them:
"Bootloader" "Nvram" "Bdata" "crash" "crash_log"
"firmware" "firmware1" "overlay" "obr"
Find the corespond block device from /proc/mtd
Read from read-only block device to avoid misoperation.
It's recommended to use /tmp/syslogbackup/ as destination, since files
would be available at http://{ROUTER_ADDR}/backup/log/YOUR_DUMP
Keep an eye on memory usage though.
3. Since UART access is locked ootb, you should get UART access by modify
uboot env. Otherwise, your router may become bricked.
Excute these in stock firmware shell:
a. nvram set boot_wait=on
b. nvram set bootdelay=3
c. nvram commit
Or in OpenWrt:
a. opkg update && opkg install kmod-mtd-rw
b. insmod mtd-rw i_want_a_brick=1
c. fw_setenv boot_wait on
d. fw_setenv bootdelay 3
e. rmmod mtd-rw
Migrate to OpenWrt:
1. Transfer squashfs-firmware.bin to the router.
2. nvram set flag_try_sys1_failed=0
3. nvram set flag_try_sys2_failed=1
4. nvram commit
5. mtd -r write /path/to/image/squashfs-firmware.bin firmware
Additional Info:
1. CR660x series routers has a different nand layout compared to other
Xiaomi nand devices.
2. This router has a relatively fresh uboot (2018.09) compared to other
Xiaomi devices, and it is capable of booting fit image firmware.
Unfortunately, no successful attempt of booting OpenWrt fit image
were made so far. The cause is still yet to be known. For now, we use
legacy image instead.
Signed-off-by: Raymond Wang <infiwang@pm.me>
|
||
Wenli Looi
|
c32008a37b |
ath79: add partial support for Netgear EX7300v2
Hardware -------- SoC: QCN5502 Flash: 16 MiB RAM: 128 MiB Ethernet: 1 gigabit port Wireless No1: QCN5502 on-chip 2.4GHz 4x4 Wireless No2: QCA9984 pcie 5GHz 4x4 USB: none Installation ------------ Flash the factory image using the stock web interface or TFTP the factory image to the bootloader. What works ---------- - LEDs - Ethernet port - 5GHz wifi (QCA9984 pcie) What doesn't work ----------------- - 2.4GHz wifi (QCN5502 on-chip) (I was not able to make this work, probably because ath9k requires some changes to support QCN5502.) Signed-off-by: Wenli Looi <wlooi@ucalgary.ca> |
||
|
Lech Perczak
|
8c78a13bfc |
ath79: support ZTE MF286
ZTE MF286 is an indoor LTE category 6 CPE router with simultaneous dual-band 802.11ac plus 802.11n Wi-Fi radios and quad-port gigabit Ethernet switch, FXS and external USB 2.0 port. Hardware highlights: - CPU: QCA9563 SoC at 775MHz, - RAM: 128MB DDR2, - NOR Flash: MX25L1606E 2MB SPI Flash, for U-boot only, - NAND Flash: GD5F1G04UBYIG 128MB SPI NAND-Flash, for all other data, - Wi-Fi 5GHz: QCA9882 2x2 MIMO 802.11ac radio, - WI-Fi 2.4GHz: QCA9563 3x3 MIMO 802.11n radio, - Switch: QCA8337v2 4-port gigabit Ethernet, with single SGMII CPU port, - WWAN: MDM9230-based category 6 internal LTE modem in extended mini-PCIE form factor, with 3 internal antennas and 2 external antenna connections, single mini-SIM slot. Modem model identified as MF270, - FXS: one external ATA port (handled entirely by modem part) with two physical connections in parallel, - USB: Single external USB 2.0 port, - Switches: power switch, WPS, Wi-Fi and reset buttons, - LEDs: Wi-Fi, Test (internal). Rest of LEDs (Phone, WWAN, Battery, Signal state) handled entirely by modem. 4 link status LEDs handled by the switch on the backside. - Battery: 3Ah 1-cell Li-Ion replaceable battery, with charging and monitoring handled by modem. - Label MAC device: eth0 Console connection: connector X2 is the console port, with the following pinout, starting from pin 1, which is the topmost pin when the board is upright: - VCC (3.3V). Do not use unless you need to source power for the converer from it. - TX - RX - GND Default port configuration in U-boot as well as in stock firmware is 115200-8-N-1. Installation: Due to different flash layout from stock firmware, sysupgrade from within stock firmware is impossible, despite it's based on QSDK which itself is based on OpenWrt. STEP 0: Stock firmware update: As installing OpenWrt cuts you off from official firmware updates for the modem part, it is recommended to update the stock firmware to latest version before installation, to have built-in modem at the latest firmware version. STEP 1: gaining root shell: Method 1: This works if busybox has telnetd compiled in the binary. If this does not work, try method 2. Using well-known exploit to start telnetd on your router - works only if Busybox on stock firmware has telnetd included: - Open stock firmware web interface - Navigate to "URL filtering" section by going to "Advanced settings", then "Firewall" and finally "URL filter". - Add an entry ending with "&&telnetd&&", for example "http://hostname/&&telnetd&&". - telnetd will immediately listen on port 4719. - After connecting to telnetd use "admin/admin" as credentials. Method 2: This works if busybox does not have telnetd compiled in. Notably, this is the case in DNA.fi firmware. If this does not work, try method 3. - Set IP of your computer to 192.168.1.22. - Have a TFTP server running at that address - Download MIPS build of busybox including telnetd, for example from: https://busybox.net/downloads/binaries/1.21.1/busybox-mips and put it in it's root directory. Rename it as "telnetd". - As previously, login to router's web UI and navigate to "URL filtering" - Using "Inspect" feature, extend "maxlength" property of the input field named "addURLFilter", so it looks like this: <input type="text" name="addURLFilter" id="addURLFilter" maxlength="332" class="required form-control"> - Stay on the page - do not navigate anywhere - Enter "http://aa&zte_debug.sh 192.168.1.22 telnetd" as a filter. - Save the settings. This will download the telnetd binary over tftp and execute it. You should be able to log in at port 23, using "admin/admin" as credentials. Method 3: If the above doesn't work, use the serial console - it exposes root shell directly without need for login. Some stock firmwares, notably one from finnish DNA operator lack telnetd in their builds. STEP 2: Backing up original software: As the stock firmware may be customized by the carrier and is not officially available in the Internet, IT IS IMPERATIVE to back up the stock firmware, if you ever plan to returning to stock firmware. Method 1: after booting OpenWrt initramfs image via TFTP: PLEASE NOTE: YOU CANNOT DO THIS IF USING INTERMEDIATE FIRMWARE FOR INSTALLATION. - Dump stock firmware located on stock kernel and ubi partitions: ssh root@192.168.1.1: cat /dev/mtd4 > mtd4_kernel.bin ssh root@192.168.1.1: cat /dev/mtd8 > mtd8_ubi.bin And keep them in a safe place, should a restore be needed in future. Method 2: using stock firmware: - Connect an external USB drive formatted with FAT or ext4 to the USB port. - The drive will be auto-mounted to /var/usb_disk - Check the flash layout of the device: cat /proc/mtd It should show the following: mtd0: 00080000 00010000 "uboot" mtd1: 00020000 00010000 "uboot-env" mtd2: 00140000 00020000 "fota-flag" mtd3: 00140000 00020000 "caldata" mtd4: 00140000 00020000 "mac" mtd5: 00600000 00020000 "cfg-param" mtd6: 00140000 00020000 "oops" mtd7: 00800000 00020000 "web" mtd8: 00300000 00020000 "kernel" mtd9: 01f00000 00020000 "rootfs" mtd10: 01900000 00020000 "data" mtd11: 03200000 00020000 "fota" Differences might indicate that this is NOT a vanilla MF286 device but one of its later derivatives. - Copy over all MTD partitions, for example by executing the following: for i in 0 1 2 3 4 5 6 7 8 9 10 11; do cat /dev/mtd$i > \ /var/usb_disk/mtd$i; done - If the count of MTD partitions is different, this might indicate that this is not a standard MF286 device, but one of its later derivatives. - (optionally) rename the files according to MTD partition names from /proc/mtd - Unmount the filesystem: umount /var/usb_disk; sync and then remove the drive. - Store the files in safe place if you ever plan to return to stock firmware. This is especially important, because stock firmware for this device is not available officially, and is usually customized by the mobile providers. STEP 3: Booting initramfs image: Method 1: using serial console (RECOMMENDED): - Have TFTP server running, exposing the OpenWrt initramfs image, and set your computer's IP address as 192.168.1.22. This is the default expected by U-boot. You may wish to change that, and alter later commands accordingly. - Connect the serial console if you haven't done so already, - Interrupt boot sequence by pressing any key in U-boot when prompted - Use the following commands to boot OpenWrt initramfs through TFTP: setenv serverip 192.168.1.22 setenv ipaddr 192.168.1.1 tftpboot 0x81000000 openwrt-ath79-nand-zte_mf286-initramfs-kernel.bin bootm 0x81000000 (Replace server IP and router IP as needed). There is no emergency TFTP boot sequence triggered by buttons, contrary to MF283+. - When OpenWrt initramfs finishes booting, proceed to actual installation. Method 2: using initramfs image as temporary boot kernel This exploits the fact, that kernel and rootfs MTD devices are consecutive on NAND flash, so from within stock image, an initramfs can be written to this area and booted by U-boot on next reboot, because it uses "nboot" command which isn't limited by kernel partition size. - Download the initramfs-kernel.bin image - Split the image into two parts on 3MB partition size boundary, which is the size of kernel partition. Pad the output of second file to eraseblock size: dd if=openwrt-ath79-nand-zte_mf286-initramfs-kernel.bin \ bs=128k count=24 \ of=openwrt-ath79-zte_mf286-intermediate-kernel.bin dd if=openwrt-ath79-nand-zte_mf286-initramfs-kernel.bin \ bs=128k skip=24 conv=sync \ of=openwrt-ath79-zte_mf286-intermediate-rootfs.bin - Copy over /usr/bin/flash_eraseall and /usr/bin/nandwrite utilities to /tmp. This is CRITICAL for installation, as erasing rootfs will cut you off from those tools on flash! - After backing up the previous MTD contents, write the images to the respective MTD devices: /tmp/flash_eraseall /dev/<kernel-mtd> /tmp/nandwrite /dev/<kernel-mtd> \ /var/usb_disk/openwrt-ath79-zte_mf286-intermediate-kernel.bin /tmp/flash_eraseall /dev/<kernel-mtd> /tmp/nandwrite /dev/<rootfs-mtd> \ /var/usb_disk/openwrt-ath79-zte_mf286-intermediate-rootfs.bin - Ensure that no bad blocks were present on the devices while writing. If they were present, you may need to vary the split between kernel and rootfs parts, so U-boot reads a valid uImage after skipping the bad blocks. If it fails, you will be left with method 3 (below). - If write is OK, reboot the device, it will reboot to OpenWrt initramfs: reboot -f - After rebooting, SSH into the device and use sysupgrade to perform proper installation. Method 3: using built-in TFTP recovery (LAST RESORT): - With that method, ensure you have complete backup of system's NAND flash first. It involves deliberately erasing the kernel. - Download "-initramfs-kernel.bin" image for the device. - Prepare the recovery image by prepending 8MB of zeroes to the image, and name it root_uImage: dd if=/dev/zero of=padding.bin bs=8M count=1 cat padding.bin openwrt-ath79-nand-zte_mf286-initramfs-kernel.bin > root_uImage - Set up a TFTP server at 192.0.0.1/8. Router will use random address from that range. - Put the previously generated "root_uImage" into TFTP server root directory. - Deliberately erase "kernel" partition" using stock firmware after taking backup. THIS IS POINT OF NO RETURN. - Restart the device. U-boot will attempt flashing the recovery initramfs image, which will let you perform actual installation using sysupgrade. This might take a considerable time, sometimes the router doesn't establish Ethernet link properly right after booting. Be patient. - After U-boot finishes flashing, the LEDs of switch ports will all light up. At this moment, perform power-on reset, and wait for OpenWrt initramfs to finish booting. Then proceed to actual installation. STEP 4: Actual installation: - scp the sysupgrade image to the device: scp openwrt-ath79-nand-zte_mf286-squashfs-sysupgrade.bin \ root@192.168.1.1:/tmp/ - ssh into the device and execute sysupgrade: sysupgrade -n /tmp/openwrt-ath79-nand-zte_mf286-squashfs-sysupgrade.bin - Wait for router to reboot to full OpenWrt. STEP 5: WAN connection establishment Since the router is equipped with LTE modem as its main WAN interface, it might be useful to connect to the Internet right away after installation. To do so, please put the following entries in /etc/config/network, replacing the specific configuration entries with one needed for your ISP: config interface 'wan' option proto 'qmi' option device '/dev/cdc-wdm0' option auth '<auth>' # As required, usually 'none' option pincode '<pin>' # If required by SIM option apn '<apn>' # As required by ISP option pdptype '<pdp>' # Typically 'ipv4', or 'ipv4v6' or 'ipv6' For example, the following works for most polish ISPs config interface 'wan' option proto 'qmi' option device '/dev/cdc-wdm0' option auth 'none' option apn 'internet' option pdptype 'ipv4' If you have build with LuCI, installing luci-proto-qmi helps with this task. Restoring the stock firmware: Preparation: If you took your backup using stock firmware, you will need to reassemble the partitions into images to be restored onto the flash. The layout might differ from ISP to ISP, this example is based on generic stock firmware. The only partitions you really care about are "web", "kernel", and "rootfs". For easy padding and possibly restoring configuration, you can concatenate most of them into images written into "ubi" meta-partition in OpenWrt. To do so, execute something like: cat mtd5_cfg-param.bin mtd6-oops.bin mtd7-web.bin mtd9-rootfs.bin > \ mtd8-ubi_restore.bin You can skip the "fota" partition altogether, it is used only for stock firmware update purposes and can be overwritten safely anyway. The same is true for "data" partition which on my device was found to be unused at all. Restoring mtd5_cfg-param.bin will restore the stock firmware configuration you had before. Method 1: Using initramfs: - Boot to initramfs as in step 3: - Completely detach ubi0 partition using ubidetach /dev/ubi0_0 - Look up the kernel and ubi partitions in /proc/mtd - Copy over the stock kernel image using scp to /tmp - Erase kernel and restore stock kernel: (scp mtd4_kernel.bin root@192.168.1.1:/tmp/) mtd write <kernel_mtd> mtd4_kernel.bin rm mtd4_kernel.bin - Copy over the stock partition backups one-by-one using scp to /tmp, and restore them individually. Otherwise you might run out of space in tmpfs: (scp mtd3_ubiconcat0.bin root@192.168.1.1:/tmp/) mtd write <ubiconcat0_mtd> mtd3_ubiconcat0.bin rm mtd3_ubiconcat0.bin (scp mtd5_ubiconcat1.bin root@192.168.1.1:/tmp/) mtd write <ubiconcat1_mtd> mtd5_ubiconcat1.bin rm mtd5_ubiconcat1.bin - If the write was correct, force a device reboot with reboot -f Method 2: Using live OpenWrt system (NOT RECOMMENDED): - Prepare a USB flash drive contatining MTD backup files - Ensure you have kmod-usb-storage and filesystem driver installed for your drive - Mount your flash drive mkdir /tmp/usb mount /dev/sda1 /tmp/usb - Remount your UBI volume at /overlay to R/O mount -o remount,ro /overlay - Write back the kernel and ubi partitions from USB drive cd /tmp/usb mtd write mtd4_kernel.bin /dev/<kernel_mtd> mtd write mtd8_ubi.bin /dev/<kernel_ubi> - If everything went well, force a device reboot with reboot -f Last image may be truncated a bit due to lack of space in RAM, but this will happen over "fota" MTD partition which may be safely erased after reboot anyway. Method 3: using built-in TFTP recovery (LAST RESORT): - Assemble a recovery rootfs image from backup of stock partitions by concatenating "web", "kernel", "rootfs" images dumped from the device, as "root_uImage" - Use it in place of "root_uImage" recovery initramfs image as in the TFTP pre-installation method. Quirks and known issues - Kernel partition size is increased to 4MB compared to stock 3MB, to accomodate future kernel updates - at this moment OpenWrt 5.10 kernel image is at 2.5MB which is dangerously close to the limit. This has no effect on booting the system - but keep that in mind when reassembling an image to restore stock firmware. - uqmi seems to be unable to change APN manually, so please use the one you used before in stock firmware first. If you need to change it, please use protocok '3g' to establish connection once, or use the following command to change APN (and optionally IP type) manually: echo -ne 'AT+CGDCONT=1,"IP","<apn>' > /dev/ttyUSB0 - The only usable LED as a "system LED" is the green debug LED hidden inside the case. All other LEDs are controlled by modem, on which the router part has some influence only on Wi-Fi LED. - Wi-Fi LED currently doesn't work while under OpenWrt, despite having correct GPIO mapping. All other LEDs are controlled by modem, including this one in stock firmware. GPIO19, mapped there only acts as a gate, while the actual signal source seems to be 5GHz Wi-Fi radio, however it seems it is not the LED exposed by ath10k as ath10k-phy0. - GPIO5 used for modem reset is a suicide switch, causing a hardware reset of whole board, not only the modem. It is attached to gpio-restart driver, to restart the modem on reboot as well, to ensure QMI connectivity after reboot, which tends to fail otherwise. - Modem, as in MF283+, exposes root shell over ADB - while not needed for OpenWrt operation at all - have fun lurking around. - MAC address shift for 5GHz Wi-Fi used in stock firmware is 0x320000000000, which is impossible to encode in the device tree, so I took the liberty of using MAC address increment of 1 for it, to ensure different BSSID for both Wi-Fi interfaces. Signed-off-by: Lech Perczak <lech.perczak@gmail.com> |
||
|
Daniel Golle
|
31872a38be
|
uboot-envtools: add configuration for UniElec U7623 board
Add U-Boot env settings to allow accessing the environment using fw_printenv and fw_setenv tools on the UniElec U7623 board. Signed-off-by: Daniel Golle <daniel@makrotopia.org> |
||
Sven Eckelmann
|
8143709c90 |
ath79: Add support for OpenMesh OM2P v1
Device specifications:
======================
* Qualcomm/Atheros AR7240 rev 2
* 350/350/175 MHz (CPU/DDR/AHB)
* 32 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2x 10/100 Mbps Ethernet
* 1T1R 2.4 GHz Wi-Fi
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x fast ethernet
- eth0
+ 18-24V passive POE (mode B)
+ used as WAN interface
- eth1
+ builtin switch port 4
+ used as LAN interface
* 12-24V 1A DC
* external antenna
The device itself requires the mtdparts from the uboot arguments to
properly boot the flashed image and to support dual-boot (primary +
recovery image). Unfortunately, the name of the mtd device in mtdparts is
still using the legacy name "ar7240-nor0" which must be supplied using the
Linux-specfic DT parameter linux,mtd-name to overwrite the generic name
"spi0.0".
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to the
device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann <sven@narfation.org>
|
||
|
Sven Eckelmann
|
97f5617259 |
ath79: Add support for OpenMesh OM5P-AC v1
Device specifications:
======================
* Qualcomm/Atheros QCA9558 ver 1 rev 0
* 720/600/240 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2T2R 2.4 GHz Wi-Fi (11n)
* 2T2R 5 GHz Wi-Fi (11ac)
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
* external h/w watchdog (enabled by default))
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* TI tmp423 (package kmod-hwmon-tmp421) for temperature monitoring
* 2x ethernet
- eth0
+ AR8035 ethernet PHY (RGMII)
+ 10/100/1000 Mbps Ethernet
+ 802.3af POE
+ used as LAN interface
- eth1
+ AR8035 ethernet PHY (SGMII)
+ 10/100/1000 Mbps Ethernet
+ 18-24V passive POE (mode B)
+ used as WAN interface
* 12-24V 1A DC
* internal antennas
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to the
device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann <sven@narfation.org>
|
||
|
Sven Eckelmann
|
72ef594550 |
ath79: Add support for OpenMesh OM5P-AN
Device specifications:
======================
* Qualcomm/Atheros AR9344 rev 2
* 560/450/225 MHz (CPU/DDR/AHB)
* 64 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 1T1R 2.4 GHz Wi-Fi
* 2T2R 5 GHz Wi-Fi
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* TI tmp423 (package kmod-hwmon-tmp421) for temperature monitoring
* 2x ethernet
- eth0
+ AR8035 ethernet PHY
+ 10/100/1000 Mbps Ethernet
+ 802.3af POE
+ used as LAN interface
- eth1
+ 10/100 Mbps Ethernet
+ builtin switch port 1
+ 18-24V passive POE (mode B)
+ used as WAN interface
* 12-24V 1A DC
* internal antennas
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to the
device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann <sven@narfation.org>
|
||
Nick McKinney
|
e0a574d4b7 |
ramips: add support for Linksys EA6350 v4
Specifications: - SoC: MT7621DAT (880MHz, 2 Cores) - RAM: 128 MB - Flash: 128 MB NAND - Ethernet: 5x 1GiE MT7530 - WiFi: MT7603/MT7613 - USB: 1x USB 3.0 This is another MT7621 device, very similar to other Linksys EA7300 series devices. Installation: Upload the generated factory.bin image via the stock web firmware updater. Reverting to factory firmware: Like other EA7300 devices, this device has an A/B router configuration to prevent bricking. Hard-resetting this device three (3) times will put the device in failsafe (default) mode. At this point, flash the OEM image to itself and reboot. This puts the router back into the 'B' image and allows for a firmware upgrade. Troubleshooting: If the firmware will not boot, first restore the factory as described above. This will then allow the factory.bin update to be applied properly. Signed-off-by: Nick McKinney <nick@ndmckinney.net> |
||
Pawel Dembicki
|
4e46ae1f69 |
kirkwood: add support for NETGEAR ReadyNAS Duo v2
NETGEAR ReadyNAS Duo v2 is a NAS based on Marvell kirkwood SoC.
Specification:
- Processor Marvell 88F6282 (1.6 GHz)
- 256MB RAM
- 128MB NAND
- 1x GBE LAN port (PHY: Marvell 88E1318)
- 1x USB 2.0
- 2x USB 3.0
- 2x SATA
- 3x button
- 5x leds
- serial on J5 connector accessible from rear panel
(115200 8N1) (VCC,TX,RX,GND) (3V3 LOGIC!)
Installation by USB + serial:
- Copy initramfs image to fat32 usb drive
- Connect pendrive to USB 2.0 front socket
- Connect serial console
- Stop booting in u-boot
- Do:
usb reset
setenv bootargs 'console=ttyS0,115200n8 earlyprintk'
setenv bootcmd 'nand read.e 0x1200000 0x200000 0x600000;bootm 0x1200000'
saveenv
fatload usb 0:1 0x1200000 openwrt-kirkwood-netgear_readynas-duo-v2-initramfs-uImage
bootm 0x1200000
- copy sysupgrade image via ssh.
- run sysupgrade
Installation by TFTP + serial:
- Setup TFTP server and copy initramfs image
- Connect serial console
- Stop booting in u-boot
- Do:
setenv bootargs 'console=ttyS0,115200n8 earlyprintk'
setenv bootcmd 'nand read.e 0x1200000 0x200000 0x600000;bootm 0x1200000'
saveenv
setenv serverip 192.168.1.1
setenv ipaddr 192.168.1.2
tftpboot 0x1200000 openwrt-kirkwood-netgear_readynas-duo-v2-initramfs-uImage
bootm 0x1200000
- copy sysupgrade image via ssh.
- run sysupgrade
Known issues:
- Power button and PHY INTn pin are connected to the same GPIO. It
causes that every network restart button is pressed in system.
As workaround, button is used as regular BTN_1.
For more info please look at file:
RND_5.3.13_WW.src/u-boot/board/mv_feroceon/mv_hal/usibootup/usibootup.c
from Netgear GPL sources.
Tested-by: Raylynn Knight <rayknight@me.com>
Tested-by: Lech Perczak <lech.perczak@gmail.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
|
||
Stijn Tintel
|
3fda16078b |
qoriq: add support for WatchGuard Firebox M300
This device is based on NXP's QorIQ T2081QDS board, with a quad-core dual-threaded 1.5 GHz ppc64 CPU and 4GB ECC RAM. The board has 5 ethernet interfaces, of which 3 are connected to the ethernet ports on the front panel. The other 2 are internally connected to a Marvell 88E6171 switch; the other 5 ports of this switch are also connected to the ethernet ports on the front panel. Installation: write the sdcard image to an SD card. Stock U-Boot will not boot, wait for it to fail then run these commands: setenv OpenWrt_fdt image-watchguard-firebox-m300.dtb setenv OpenWrt_kernel watchguard_firebox-m300-kernel.bin setenv wgBootSysA 'setenv bootargs root=/dev/mmcblk0p2 rw rootdelay=2 console=$consoledev,$baudrate fsl_dpaa_fman.fsl_fm_max_frm=1530; ext2load mmc 0:1 $fdtaddr $OpenWrt_fdt; ext2load mmc 0:1 $loadaddr $OpenWrt_kernel; bootm $loadaddr - $fdtaddr' saveenv reset The default U-Boot boot entry will now boot OpenWrt from the SD card. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> Acked-by: Rui Salvaterra <rsalvaterra@gmail.com> |
||
TruongSinh Tran-Nguyen
|
febc2b831f
|
ipq40xx: add support for GL.iNet GL-B2200
This patch adds supports for the GL-B2200 router. Specifications: - SOC: Qualcomm IPQ4019 ARM Quad-Core - RAM: 512 MiB - Flash: 16 MiB NOR - SPI0 - EMMC: 8GB EMMC - ETH: Qualcomm QCA8075 - WLAN1: Qualcomm Atheros QCA4019 2.4GHz 802.11b/g/n 2x2 - WLAN2: Qualcomm Atheros QCA4019 5GHz 802.11n/ac W2 2x2 - WLAN3: Qualcomm Atheros QCA9886 5GHz 802.11n/ac W2 2x2 - INPUT: Reset, WPS - LED: Power, Internet - UART1: On board pin header near to LED (3.3V, TX, RX, GND), 3.3V without pin - 115200 8N1 - UART2: On board with BLE module - SPI1: On board socket for Zigbee module Update firmware instructions: Please update the firmware via U-Boot web UI (by default at 192.168.1.1, following instructions found at https://docs.gl-inet.com/en/3/troubleshooting/debrick/). Normal sysupgrade, either via CLI or LuCI, is not possible from stock firmware. Please do use the *gl-b2200-squashfs-emmc.img file, gunzipping the produced *gl-b2200-squashfs-emmc.img.gz one first. What's working: - WiFi 2G, 5G - WPA2/WPA3 Not tested: - Bluetooth LE/Zigbee Credits goes to the original authors of this patch. V1->V2: - updates *arm-boot-add-dts-files.patch correctly (sorry, my mistake) - add uboot-envtools support V2->V3: - Li Zhang updated official patch to fix wrong MAC address on wlan0 (PCI) interface V3->V4: - wire up sysupgrade Signed-off-by: Li Zhang <li.zhang@gl-inet.com> [fix tab and trailing space, document what's working and what's not] Signed-off-by: TruongSinh Tran-Nguyen <i@truongsinh.pro> [rebase on top of master, address remaining comments] Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com> [remove redundant check in platform.sh] Signed-off-by: Daniel Golle <daniel@makrotopia.org> |
||
|
Piotr Dymacz
|
ddfebaff9f |
uboot-envtools: move imx to imx_cortexa9
Subtarget-specific files under 'uboot-envtools' package are supported
since
|
||
|
Piotr Dymacz
|
346db2f3b0 |
uboot-envtools: rename 'imx6' to 'imx'
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com> |
||
|
Daniel Golle
|
cb5953635e
|
uboot-envtools: mt7622: make use of find_mmc_part
Signed-off-by: Daniel Golle <daniel@makrotopia.org> |
||
Jihoon Han
|
84451173f0 |
ath79: add support for Dongwon T&I DW02-412H
Dongwon T&I DW02-412H is a 2.4/5GHz band 11ac (WiFi-5) router, based on
Qualcomm Atheros QCA9557.
Specifications
--------------
- SoC: Qualcomm Atheros QCA9557-AT4A
- RAM: DDR2 128MB
- Flash: SPI NOR 2MB (Winbond W25Q16DVSSIG / ESMT F25L16PA(2S)) +
NAND 64/128MB
- WiFi:
- 2.4GHz: QCA9557 WMAC
- 5GHz: QCA9882-BR4A
- Ethernet: 5x 10/100/1000Mbps
- Switch: QCA8337N-AL3C
- USB: 1x USB 2.0
- UART:
- JP2: 3.3V, TX, RX, GND (3.3V is the square pad) / 115200 8N1
Installation
--------------
1. Connect a serial interface to UART header and
interrupt the autostart of kernel.
2. Transfer the factory image via TFTP and write it to the NAND flash.
3. Update U-Boot environment variable.
> tftpboot 0x81000000 <your image>-factory.img
> nand erase 0x1000000
> nand write 0x81000000 0x1000000 ${filesize}
> setenv bootpart 2
> saveenv
Revert to stock firmware
--------------
1. Revert to stock U-Boot environment variable.
> setenv bootpart 1
> saveenv
MAC addresses as verified by OEM firmware
--------------
WAN: *:XX (label)
LAN: *:XX + 1
2.4G: *:XX + 3
5G: *:XX + 4
The label MAC address was found in art 0x0.
Credits
--------------
Credit goes to the @manatails who first developed how to port OpenWRT
to this device and had a significant impact on this patch.
And thanks to @adschm and @mans0n for guiding me to revise the code
in many ways.
Signed-off-by: Jihoon Han <rapid_renard@renard.ga>
Reviewed-by: Sungbo Eo <mans0n@gorani.run>
Tested-by: Sungbo Eo <mans0n@gorani.run>
|
||
Eduardo Santos
|
3c97fb4346 |
ramips: add support for Xiaomi MiWifi 3C
This commit adds support for Xiaomi MiWiFi 3C device. Xiaomi MiWifi 3C has almost the same system architecture as the Xiaomi Mi WiFi Nano, which is already officially supported by OpenWrt. The differences are: - Numbers of antennas (4 instead of 2). The antenna management is done via the µC. There is no configuration needed in the software code. - LAN port assignments are different. LAN1 and WAN are interchanged. OpenWrt Wiki: https://openwrt.org/toh/xiaomi/mir3c OpenWrt developers forum page: https://forum.openwrt.org/t/support-for-xiaomi-mi-3c Specifications: - CPU: MediaTek MT7628AN (575MHz) - Flash: 16MB - RAM: 64MB DDR2 - 2.4 GHz: IEEE 802.11b/g/n with Integrated LNA and PA - Antennas: 4x external single band antennas - WAN: 1x 10/100M - LAN: 2x 10/100M - LED: 1x amber/blue/red. Programmable - Button: Reset MAC addresses as verified by OEM firmware: use address source LAN *:92 factory 0x28 WAN *:92 factory 0x28 2g *:93 factory 0x4 OEM firmware uses VLAN's to create the network interface for WAN and LAN. Bootloader info: The stock bootloader uses a "Dual ROM Partition System". OS1 is a deep copy of OS2. The bootloader start OS2 by default. To force start OS1 it is needed to set "flag_try_sys2_failed=1". How to install: 1- Use OpenWRTInvasion to gain telnet, ssh and ftp access. https://github.com/acecilia/OpenWRTInvasion (IP: 192.168.31.1 - Username: root - Password: root) 2- Connect to router using telnet or ssh. 3- Backup all partitions. Use command "dd if=/dev/mtd0 of=/tmp/mtd0". Copy /tmp/mtd0 to computer using ftp. 4- Copy openwrt-ramips-mt76x8-xiaomi_miwifi-3c-squashfs-sysupgrade.bin to /tmp in router using ftp. 5- Enable UART access and change start image for OS1. ``` nvram set uart_en=1 nvram set flag_last_success=1 nvram set boot_wait=on nvram set flag_try_sys2_failed=1 nvram commit ``` 6- Installing Openwrt on OS1 and free OS2. ``` mtd erase OS1 mtd erase OS2 mtd -r write /tmp/openwrt-ramips-mt76x8-xiaomi_miwifi-3c-squashfs-sysupgrade.bin OS1 ``` Limitations: For the first install the image size needs to be less than 7733248 bits. Thanks for all community and especially for this device: minax007, earth08, S.Farid Signed-off-by: Eduardo Santos <edu.2000.kill@gmail.com> [wrap lines, remove whitespace errors, add mediatek,mtd-eeprom to &wmac, convert to nvmem] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> |
||
|
Robert Marko
|
78cf3e53b1 |
mvebu: add Globalscale MOCHAbin
Globalscale MOCHAbin is a Armada 7040 based development board.
Specifications:
* Armada 7040 Quad core ARMv8 Cortex A-72 @ 1.4GHz
* 2 / 4 / 8 GB of DDR4 DRAM
* 16 GB eMMC
* 4MB SPI-NOR (Bootloader)
* 1x M.2-2280 B-key socket (for SSD expansion, SATA3 only)
* 1x M.2-2250 B-key socket (for modems, USB2.0 and I2C only)
* 1x Mini-PCIe 3.0 (x1, USB2.0 and I2C)
* 1x SATA 7+15 socket (SATA3)
* 1x 16-pin (2×8) MikroBus Connector
* 1x SIM card slot (Connected to the mini-PCIe and both M.2 slots)
* 2x USB3.0 Type-A ports via SMSC USB5434B hub
* Cortex 2x5 JTAG
* microUSB port for UART (PL2303GL/PL2303SA onboard)
* 1x 10G SFP+
* 1x 1G SFP (Connected to 88E1512 PHY)
* 1x 1G RJ45 with PoE PD (Connected to 88E1512 PHY)
* 4x 1G RJ45 ports via Topaz 88E6141 switch
* RTC with battery holder (SoC provided, requires CR2032 battery)
* 1x 12V DC IN
* 1x Power switch
* 1x 12V fan header (3-pin, power only)
* 1x mini-PCIe LED header (2x0.1" pins)
* 1x M.2-2280 LED header (2x0.1" pins)
* 6x Bootstrap jumpers
* 1x Power LED (Green)
* 3x Tri-color RGB LEDs (Controllable)
* 1x Microchip ATECC608B secure element
Note that 1G SFP and 1G WAN cannot be used at the same time as they are in
parallel connected to the same PHY.
Installation:
Copy dtb from build_dir to bin/ and run tftpserver there:
$ cp ./build_dir/target-aarch64_cortex-a72_musl/linux-mvebu_cortexa72/image-armada-7040-mochabin.dtb bin/targets/mvebu/cortexa72/
$ in.tftpd -L -s bin/targets/mvebu/cortexa72/
Connect to the device UART via microUSB port and power on the device.
Power on the device and hit any key to stop the autoboot.
Set serverip (host IP) and ipaddr (any free IP address on the same subnet), e.g:
$ setenv serverip 192.168.1.10 # Host
$ setenv ipaddr 192.168.1.15 # Device
Set the ethernet device (Example for the 1G WAN):
$ setenv ethact mvpp2-2
Ping server to confirm network is working:
$ ping $serverip
Using mvpp2-2 device
host 192.168.1.15 is alive
Tftpboot the firmware:
$ tftpboot $kernel_addr_r openwrt-mvebu-cortexa72-globalscale_mochabin-initramfs-kernel.bin
$ tftpboot $fdt_addr_r image-armada-7040-mochabin.dtb
Boot the image:
$ booti $kernel_addr_r - $fdt_addr_r
Once the initramfs is booted, transfer openwrt-mvebu-cortexa72-globalscale_mochabin-squashfs-sdcard.img.gz
to /tmp dir on the device.
Gunzip and dd the image:
$ gunzip /tmp/openwrt-mvebu-cortexa72-globalscale_mochabin-squashfs-sdcard.img.gz
$ dd if=/tmp/openwrt-mvebu-cortexa72-globalscale_mochabin-squashfs-sdcard.img of=/dev/mmcblk0 && sync
Reboot the device.
Hit any key to stop the autoboot.
Reset U-boot env and set the bootcmd:
$ env default -a
$ setenv bootcmd 'load mmc 0 ${loadaddr} boot.scr && source ${loadaddr}'
Optionally I would advise to edit the console env variable to remove earlycon as that
causes the kernel to never use the driver for the serial console.
Earlycon should be used only for debugging before the kernel can configure the console
and will otherwise cause various issues with the console.
$ setenv console 'console=ttyS0,115200'
Save and reset
$ saveenv
$ reset
OpenWrt should boot from eMMC now.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
|
||
Soma Zambelly
|
c5b44af2fc |
realtek: add ZyXEL GS1900-24HPv2 support
The ZyXEL GS1900-24HPv2 is a 24 port PoE switch with two SFP ports, similar to the other GS1900 switches.
Specifications
--------------
* Device: ZyXEL GS1900-24HPv2
* SoC: Realtek RTL8382M 500 MHz MIPS 4KEc
* Flash: 16 MiB
* RAM: W631GG8MB-12 128 MiB DDR3 SDRAM
(stock firmware is configured to use only 64 MiB)
* Ethernet: 24x 10/100/1000 Mbps, 2x SFP 100/1000 Mbps
* LEDs: 1 PWR LED (green, not configurable)
1 SYS LED (green, configurable)
24 ethernet port link/activity LEDs (green, SoC controlled)
24 ethernet port PoE status LEDs
2 SFP status/activity LEDs (green, SoC controlled)
* Buttons: 1 "RESTORE" button on front panel
1 "RESET" button on front panel
* Power 120-240V AC C13
* UART: 1 serial header (J41) with populated standard pin connector on
the left edge of the PCB, angled towards the side.
The casing has a rectangular cutout on the side that provides
external access to these pins.
Pinout (front to back):
+ GND
+ TX
+ RX
+ VCC
Serial connection parameters for both devices: 115200 8N1.
Installation
------------
OEM upgrade method:
(Possible on master once https://patchwork.ozlabs.org/project/openwrt/patch/20210624210408.19248-1-bjorn@mork.no/ is merged)
* Log in to OEM management web interface
* Navigate to Maintenance > Firmware > Management
* If "Active Image" has the first option selected, OpenWrt will need to be
flashed to the "Active" partition. If the second option is selected,
OpenWrt will need to be flashed to the "Backup" partition.
* Navigate to Maintenance > Firmware > Upload
* Upload the openwrt-realtek-generic-zyxel_gs1900-24hp-v2-initramfs-kernel.bin
file by your preferred method to the previously determined partition.
When prompted, select to boot from the newly flashed image, and reboot the switch.
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade -n /tmp/openwrt-realtek-generic-zyxel_gs1900-24hp-v2-squashfs-sysupgrade.bin
it may be necessary to restart the network (/etc/init.d/network restart) on
the running initramfs image.
U-Boot TFTP method:
* Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10).
* Set up a TFTP server on your client and make it serve the initramfs image.
* Connect serial, power up the switch, interrupt U-boot by hitting the
space bar, and enable the network:
> rtk network on
* Since the GS1900-24HPv2 is a dual-partition device, you want to keep the OEM
firmware on the backup partition for the time being. OpenWrt can only boot
from the first partition anyway (hardcoded in the DTS). To make sure we are
manipulating the first partition, issue the following commands:
> setsys bootpartition 0
> savesys
* Download the image onto the device and boot from it:
> tftpboot 0x84f00000 192.168.1.10:openwrt-realtek-generic-zyxel_gs1900-24hp-v2-initramfs-kernel.bin
> bootm
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade -n /tmp/openwrt-realtek-generic-zyxel_gs1900-24hp-v2-squashfs-sysupgrade.bin
it may be necessary to restart the network (/etc/init.d/network restart) on
the running initramfs image.
Signed-off-by: Soma Zambelly <zambelly.soma@gmail.com>
|
||
Andrea Poletti
|
de0c380a5f |
ramips: add support for Sitecom WLR-4100 v1 002
Sitecom WLR-4100 v1 002 (marked as X4 N300) is a wireless router
Specification:
SoC: MT7620A
RAM: 64 MB DDR2
Flash: MX25L6405D SPI NOR 8 MB
WIFI: 2.4 GHz integrated
Ethernet: 5x 10/100/1000 Mbps QCA8337
USB: 1x 2.0
LEDS: 2x GPIO controlled, 5x switch
Buttons: 1x GPIO controlled
UART: row of 4 unpopulated holes near USB port, starting count from
white triangle on PCB:
VCC 3.3V
GND
TX
RX
baud: 115200, parity: none, flow control: none
Installation
Connect to one of LAN (yellow) ethernet ports,
Open router configuration interface,
Go to Toolbox > Firmware,
Browse for OpenWrt factory image with dlf extension and hit Apply,
Wait few minutes, after the Power LED will stop blinking, the router is
ready for configuration.
Known issues
Some USB 2.0 devices work at full speed mode 1.1 only
MAC addresses
factory partition only contains one (binary) MAC address in 0x4.
u-boot-env contains four (ascii) MAC addresses, of which two appear
to be valid.
factory 0x4 **:**:**:**:b9:84 binary
u-boot-env ethaddr **:**:**:**:b9:84 ascii
u-boot-env wanaddr **:**:**:**:b9:85 ascii
u-boot-env wlanaddr 00:AA:BB:CC:DD:12 ascii
u-boot-env iNICaddr 00:AA:BB:CC:DD:22 ascii
The factory firmware only assigns ethaddr. Thus, we take the
binary value which we can use directly in DTS.
Additional information
OEM firmware shell password is: SitecomSenao
useful for creating backup of original firmware.
There is also another revision of this device (v1 001), based on RT3352 SoC
Signed-off-by: Andrea Poletti <polex73@yahoo.it>
[remove config DT label, convert to nvmem, remove MAC address
setup from u-boot-env, add MAC address info to commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|