Commit Graph

176 Commits

Author SHA1 Message Date
Ben Greear
545a561785 ath10k-ct: Update wave-1 and wave-2 firmware to latest.
This updates to latest ath10k-ct firmware.  Hopefully we are
at the end of the development cycle for this firmware release,
so these should be stable.

wave-1 changes since last release:

Release 20

  *  Allow flushing peer when deleting.  Hopefully this will allow the
     peer delete command to happen in a reasonable amount of time even
     if the RF environment is busy (or peer has died).
     To enable this, set the high flag in the mac-addr second word in the
     ath10k driver near end of the ath10k_wmi_op_gen_peer_delete method:

     cmd->peer_macaddr.word1 |= __cpu_to_le32(0x80000000);

  *  Attempt to fix crash seen in resmgr-ocs, appearantly due to list corruption.
     Use a temporary list instead of trying to rely on for-each-safe.

  *  Add flag to tx-descriptor to allow driver to request no-ack on data
     frames.  This is bit 15 on the flag1 field (previously un-used).

  *  Add option to support specifying the tx-rate-code and retry count on
     a per-packet basis.  Only a single series is supported at this time.
     Useful mainly for radiotap monitor-tx type testing at this point.

  *  Fix crash on startup when chip is at -40 deg C and calibration fails.  Instead
     of asserting, just keep retrying calibration, which appears to start working
     after a few minutes (when the chip warms up).

  *  Allow reporting per-chain rssi for management frames.  We pack the values into
     empty space in the mgt-frame wmi header.  This will only be enabled if the driver
     requests it, since otherwise the driver is assumed to not understand the new API.
     ath10k-ct drivers that support this feature will automatically enable it.

  *  A customer reports a case that appears to be the hardware not properly detecting
     end of AMPDU, so frames were being mis-delivered to the wrong peer.  Attempt to
     work around this, and in doing so, clean up a bunch of void* abuse in the block-ack
     reordering code (could not ever confirm there was a problem in this area).

  *  Re-work the rx-mem logic to be less complicated and to use less memory.

  *  Attempt to fix crash that appearanty happens because the driver can sometimes
     delete a vdev in 'up' state.

  *  Attempt to fix hung scan state machine issues.

  *  Fix crash in tx path due to un-initialized memory.

wave-2 changes since last release:

Release 10

  *  Fix an assert related to tx scheduling.  This hopefully fixes
     what appears to be a regression that I added some time back.

  *  Enable CSI reporting for 9984, and maybe 9888/9886.  Only in
     non-trimmed builds.

  *  Other stability improvements, including regression fixes from
     some tricky bugs introduced in earlier releases.

  *  Allow compiling for IPQ4019 chipset.

  *  Firmware will now send txbf frames to the host (driver) if the
     TXBF (0xF00000001) set-special feature is enabled, or when the radio
     is in monitor mode.  But, if the frame is consumed by the txbf_cv
     logic, then the pkt cannot be delivered to the host in this manner.  Instead,
     a WMI event will be sent and host can find the txbf_cv data in shared
     memory.  See ath10k_wmi_event_txbf_cv_mesg() in ath10k-ct driver.

  *  Support rx-all-mgt option.  When enabled, the firmware will deliver all
     management frames that it can to the host.  No RX filters are changed
     when this option is enabled.

  *  Fix at least some problems with sending tx-beamforming frames to SU-MIMO
     peers.  Looks like this was a regression in my code.

  *  Fix a crash in rate-ctrl due to nss mismatch.  This was something I introduced
     while trying to fix other bugs in rate-ctrl some time back.

  *  Attempt to fix a sw-peer-key object leak in IBSS mode.  The peer key code
     is very complex, and shares some pointers as union members.  I think I fixed
     at least some of the issues, but would not be surprised if more exist.

  *  Improve ath10k user guide to document CT firmware features:
     https://www.candelatech.com/ath10k-ug.php

  *  Add ct-special option to configure the txbf sounding time.  See ath10k-ug.php

  *  Fix and allow the driver to tell the firmware to send sounding frames.  See ath10k-ug.php
     In further testing, this seems to fail much of the time, and I am not sure why.
     Disabling this in diet (trimmed) builds.

  *  Fix crashes related to deleting peers while they are in power-save mode.  Reported
     by LEDE user on r7800 with 9984 NIC.
  *  Make rate-ctrl txbf probe work better.  If enabled, the rate-ctrl logic will periodically
     send out probes at an NSS that can to txbf.  Previously, txbf probes would not reliably happen
     if both AP and peer had the same nss (ie, 2x2 talking to 2x2).  To enable this feature, you
     need to enable the fwtest-cmdid number 20.

  *  Report rx-timeout error counters.  These were previously un-reported, though the
     field existed in the wmi struct already.

  *  txbf:  Ignore frames not destined for us.  If NIC is in promisc mode, it
     could acquire and process NDPA frames that were not destined for it.  Check
     the dest-MAC and ignore frames not for us (pass them up the stack for monitor
     mode instead of save them in the peer's rate-ctrl logic.)

  *  Port ping-pong crash handling and othe related features to IPQ4019 target.  It should
     now act similar to 9984 in this regard.

  *  Fix a few asserts related to txbf and tx-seq logic.

  *  Add custom-stats support, for rx-reorder-stats.  Similar to what I did for wave-1.

  *  Disable AMSDU for IBSS.  This now matches what I did for peregrine.  It seems to
     work better this way, though I did not debug it in detail.

  *  Enable the set-special command to re-enable AMSDU for IBSS if user wants to experiment.

  *  Fix bug where dbglog did not disable IRQs, so if you made dbglog messages from the IRQ
     handler, it could cause corruption that could crash the firmware and/or corrupt the log
     message buffers.

  *  Don't assert if there are no buffer descriptors for RX of non-data frame.

  *  Retry any stuck block-ack sessions every 20 seconds instead of just disabling BA for
     ever when we get too many failures.

  *  Fix SGI flag when reporting tx-rate info.  The flag moved since wave-1 days, and
     I did not notice that when I ported my changes forward to wave-2.

  *  Allow disabling special CCA handling for IBSS txqs.  Earlier testing indicated this
     might improve throughput in some testing on 9984 chips in IBSS mode, but subsequent
     testing looks about the same without it.  Since I do not really understand what this
     setting exists for, leave it at upstream defaults.  A new set-special API command (0x12)
     can be used to enable this hack for testing.  Setting 0x1 bit disables special CCA handling
     for non-beacon IBSS txqs, setting 0x2 bit disables it for beacon queues as well.

  *  Add MCAST-BCAST feature flag.  This tells driver we do not need a monitor interface
     to do MESH.

  *  When calculating the rx-address filter (affects ACK & BLOCK-ACK, among other things),
     to not add in monitor interfaces if other interfaces are up.  There is no need for
     a monitor device to ACK frames.

Signed-off-by: Ben Greear <greearb@candelatech.com>
2018-03-23 22:08:22 +01:00
Ben Greear
375be15429 ath10k-ct: Update DEPENDS and PROVIDES
Update DEPENDS and PROVIDES so that ath10k-ct firmware
and drivers can be used to replace stock firmware
and drivers.  The -htt firmware variant, which requires
ath10k-ct driver now selects ath10k-ct driver when the
firmware is selected.

Signed-off-by: Ben Greear <greearb@candelatech.com>
2018-03-23 22:08:22 +01:00
Ben Greear
8bb9f8dd47 ath10k-firmware: Support CT IPQ4019 firmware.
Initial beta release of the CT IPQ4019 firmware.  Features are
similar to the CT 9984 firmware

Signed-off-by: Ben Greear <greearb@candelatech.com>
2018-03-22 09:09:55 +01:00
Zoltan HERPAI
3db9d6e57d intel-microcode: update to 20180312
- Update microcode for 24 CPU types
- Implements IBRS/IBPB/STIPB support, Spectre-v2 mitigation for:
  Sandybridge, Ivy Bridge, Haswell, Broadwell, Skylake, Kaby Lake,
  Coffee Lake
- Missing production updates:
   - Broadwell-E/EX Xeons (sig 0x406f1)
   - Anniedale/Morefield, Apollo Lake, Avoton, Cherry Trail, Braswell,
     Gemini Lake, Denverton
- New Microcodes:
   - sig 0x00050653, pf_mask 0x97, 2018-01-29, rev 0x1000140
   - sig 0x00050665, pf_mask 0x10, 2018-01-22, rev 0xe000009

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2018-03-21 23:24:09 +01:00
Mathias Kresin
35e01cf68a ipq-wifi: add board-2.bin for ASUS RT-AC58U
The existing file is 0 byte. Replace the ASUS RT-AC58U board-2.bin with
the correct file.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-03-15 21:00:39 +01:00
Chris Blake
4943afd781 ipq40xx: add Cisco Meraki MR33 Support
This patch adds support for Cisco Meraki MR33

hardware highlights:

SOC:	IPQ4029 Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM:	256 MiB DDR3L-1600 @ 627 MHz Micron MT41K128M16JT-125IT
NAND:	128 MiB SLC NAND Spansion S34ML01G200TFV00 (106 MiB usable)
ETH:	Qualcomm Atheros AR8035 Gigabit PHY (1 x LAN/WAN) + PoE
WLAN1:	QCA9887 (168c:0050) PCIe 1x1:1 802.11abgn ac Dualband VHT80
WLAN2:	Qualcomm Atheros QCA4029 2.4GHz 802.11bgn 2:2x2
WLAN3:	Qualcomm Atheros QCA4029 5GHz 802.11a/n/ac 2:2x2 VHT80
LEDS:	1 x Programmable RGB+White Status LED (driven by Ti LP5562 on i2c-1)
	1 x Orange LED Fault Indicator (shared with LP5562)
	2 x LAN Activity / Speed LEDs (On the RJ45 Port)
BUTTON:	one Reset button
MISC:	Bluetooth LE Ti cc2650 PG2.3 4x4mm - BL_CONFIG at 0x0001FFD8
	AT24C64 8KiB EEPROM
	Kensington Lock

Serial:
	WARNING: The serial port needs a TTL/RS-232 3V3 level converter!
	The Serial setting is 115200-8-N-1. The board has a populated
	1x4 0.1" header with half-height/low profile pins.
	The pinout is: VCC (little white arrow), RX, TX, GND.

Flashing needs a serial adaptor, as well as patched ubootwrite utility
(needs Little-Endian support). And a modified u-boot (enabled Ethernet).
Meraki's original u-boot source can be found in:
<https://github.com/riptidewave93/meraki-uboot/tree/mr33-20170427>

Add images to do an installation via bootloader:
 0. open up the MR33 and connect the serial console.

 1. start the 2nd stage bootloader transfer from client pc:

  # ubootwrite.py --write=mr33-uboot.bin
  (The ubootwrite tool will interrupt the boot-process and hence
   it needs to listen for cues. If the connection is bad (due to
   the low-profile pins), the tool can fail multiple times and in
   weird ways. If you are not sure, just use a terminal program
   and see what the device is doing there.

 2. power on the MR33 (with ethernet + serial cables attached)
    Warning: Make sure you do this in a private LAN that has
    no connection to the internet.

 - let it upload the u-boot this can take 250-300 seconds -

 3. use a tftp client (in binary mode!) on your PC to upload the sysupgrade.bin
    (the u-boot is listening on 192.168.1.1)
    # tftp 192.168.1.1
    binary
    put openwrt-ipq40xx-meraki_mr33-squashfs-sysupgrade.bin

 4. wait for it to reboot

 5. connect to your MR33 via ssh on 192.168.1.1

For more detailed instructions, please take a look at the:
"Flashing Instructions for the MR33" PDF. This can be found
on the wiki: <https://openwrt.org/toh/meraki/mr33>
(A link to the mr33-uboot.bin + the modified ubootwrite is
also there)

Thanks to Jerome C. for sending an MR33 to Chris.

Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-03-14 19:04:52 +01:00
Christian Lamparter
87c42101cf ipq40xx: add support for ASUS RT-AC58U/RT-ACRH13
This patch adds support for ASUS RT-AC58U/RT-ACRH13.

hardware highlights:

SOC:	IPQ4018 / QCA Dakota
CPU:	Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM:	128 MiB DDR3L-1066 @ 537 MHz (1074?) NT5CC64M16GP-DI
NOR:	2 MiB Macronix MX25L1606E (for boot, QSEE)
NAND:   128 MiB Winbond W25NO1GVZE1G (cal + kernel + root, UBI)
ETH:    Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN)
USB:    1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
WLAN1:  Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2:  Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT:	one Reset and one WPS button
LEDS:	Status, WAN, WIFI1/2, USB and LAN (one blue LED for each)
Serial:
	WARNING: The serial port needs a TTL/RS-232 3V3 level converter!
	The Serial setting is 115200-8-N-1. The board has an unpopulated
	1x4 0.1" header. The pinout (VDD, RX, GND, TX) is printed on the
	PCB right next to the connector.

U-Boot Note: The ethernet driver isn't always reliable and can sometime
time out... Don't worry, just retry.

Access via the serial console is required. As well as a working
TFTP-server setup and the initramfs image. (If not provided, it
has to be built from the OpenWrt source. Make sure to enable
LZMA as the compression for the INITRAMFS!)

To install the image permanently, you have to do the following
steps in the listed order.

1. Open up the router.
   There are four phillips screws hiding behind the four plastic
   feets on the underside.

2. Connect the serial cable (See notes above)

3. Connect your router via one of the four LAN-ports (yellow)
   to a PC which can set the IP-Address and ssh and scp from.

   If possible set your PC's IPv4 Address to 192.168.1.70
   (As this is the IP-Address the Router's bootloader expects
   for the tftp server)

4. power up the router and enter the u-boot
   choose option 1 to upload the initramfs image. And follow
   through the ipv4 setup.

Wait for your router's status LED to stop blinking rapidly and
glow just blue. (The LAN LED should also be glowing blue).

3. Connect to the OpenWrt running in RAM

   The default IPv4-Address of your router will be 192.168.1.1.

   1. Copy over the openwrt-sysupgrade.bin image to your router's
      temporary directory

   # scp openwrt-sysupgrade.bin root@192.168.1.1:/tmp

   2. ssh from your PC into your router as root.

   # ssh root@192.168.1.1

   The default OpenWrt-Image won't ask for a password. Simply hit the Enter-Key.

   Once connected...: run the following commands on your temporary installation

   3. delete the "jffs2" ubi partition to make room for your new root partition

   # ubirmvol /dev/ubi0 --name=jffs2

   4. install OpenWrt on the NAND Flash.

   # sysupgrade -v /tmp/openwrt-sysupgrade.bin

   - This will will automatically reboot the router -

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-03-14 19:04:51 +01:00
John Crispin
54b275c8ed ipq40xx: add target
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: John Crispin <john@phrozen.org>
2018-03-14 19:04:50 +01:00
Henryk Heisig
21486911ac firmware: ath10k-firmware: update QCA9984 firmware to 10.4-3.5.3-00053
This patch updates ath10k-firmware to use the
firmware-5.bin_10.4-3.5.3-00053 firmware for the QCA9984.

The update fixes "ath10k_pci 0001:01:00.0: Invalid VHT mcs 15 peer
stats" spamming the kernel ring buffer at very high frequencies, but
introduces the new "ath10k_pci 0001:01:00.0: Unknown eventid: 36925".
This new warning doesn't appear to cause problems in practice and is
only emitted relatively rarely, not causing dmesg to overflow within
minutes.

Tested on the ZyXEL NBG6817; early feedback also suggests this firmware
to work well (with the same fixes and caveats) on the Netgear r7800 as
well.

Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2018-03-09 22:15:02 +01:00
Henryk Heisig
11b476f925 firmware: ath10k-firmware: update to 2018-02-09
This patch updates ath10k-firmware to last commit and use the
firmware-5.bin_10.4-3.5.3-00053 firmware for the QCA9888.

Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2018-03-09 22:15:01 +01:00
Stijn Segers
dc7f2fdd52 linux-firmware: bump firmware for Intel Wireless 8260AC to version 31
Bump the firmware for 8260AC and related hardware to version 31.

Signed-off-by: Stijn Segers <foss@volatilesystems.org>
2018-03-09 22:13:21 +01:00
Dongming Han
04d3308b62 ipq806x: add support for GL.iNet GL-B1300
This patch adds support for GL.iNet GL-B1300

Specification:
- SOC:        IPQ4028 / QCA Dakota
- RAM:        256 MiB
- FLASH:      32 MiB
- ETH:        Qualcomm Atheros QCA8075 Gigabit Switch (2 x LAN, 1 x WAN)
- USB:        1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
- WLAN1:      Qualcomm Atheros QCA4028 2.4GHz 802.11bgn 2:2x2
- WLAN2:      Qualcomm Atheros QCA4028 5GHz 802.11a/n/ac 2:2x2
- INPUT:      one reset and one WPS button
- LEDS:       3 leds: Power, WIFI(only for 2.4G currently), and one reserved
- UART:       1 x UART on PCB (3.3V, TX, RX, GND) - 115200 8N1

Installation:
Method 1:
- use serial port to stop uboot
- uboot command: run lf
Method 2:
- push down reset button and power on
- wait until three leds constantly on then release
- upgrade by uboot web at http://192.168.1.1
Note:
- the sysupgrade image need to be renamed to lede-gl-b1300.bin in both method.
- the sysupgrade image can be automatically downloaded if tftp server at
  192.168.1.2 have that file.
- the wifi led will be flashing when writing image.

Signed-off-by: Dongming Han <handongming@gl-inet.com>
2018-02-14 09:40:32 +01:00
Yangbo Lu
0f7c83bb26 layerscape: update ppfe firmware to LSDK1712
Updated ppfe firmware to NXP LSDK1712 release. Used
ppfe firmware git tree on NXP github since it was
migrated here from qoriq-open-source github.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2018-02-13 10:01:51 +01:00
Yangbo Lu
13b2735a46 layerscape: add ls-rcw-bin package
NXP LSDK1712 release used two rcw git trees. The
original rcw git tree was still source code but
dropping ls1012a/ls1088a/ls2088a boards in LSDK1712.
Instead another new rcw git tree was used to just
provided rcw binaries for these boards dropped. So
this patch is to update ls-rcw to LSDK1712 release
and add a new ls-rcw-bin package.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2018-02-13 10:01:50 +01:00
Yangbo Lu
0a4d12b769 layerscape: update PPA firmware to LSDK1712
This patch is to update PPA firmware to NXP LSDK1712
release.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2018-02-13 10:01:50 +01:00
Yangbo Lu
4e85171e85 layerscape: migrate fman-ucode to NXP github
fman-ucode had been migrated from qoriq-open-source
github to NXP github. So the Makefile should be fixed
accordingly.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2018-02-13 10:01:50 +01:00
Yangbo Lu
f613743687 layerscape: update MC firmware to LSDK1712
Updated MC firmware to NXP LSDK1712 release. Used
MC firmware git tree on NXP github since it was
migrated here from qoriq-open-source github.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2018-02-13 10:01:50 +01:00
Sven Eckelmann
25a72f5a01 ipq-wifi: drop OpenMesh A42 board-2.bin
The BDFs for OpenMesh A42 were upstreamed [1] to the ath10k-firmware
repository and are now part of ath10k-firmware 2018-01-26. The
ipq-wifi-openmesh_a42 package can now be dropped because OpenWrt already
ships the QCA4019 board-2.bin from this version.

[1] https://wireless.wiki.kernel.org/en/users/drivers/ath10k/boardfiles

Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2018-02-11 16:33:00 +01:00
Sven Eckelmann
80b54b85ad firmware: ath10k-firmware: update to 2018-01-26
* introduces the BDFs for the OpenMesh A42 in
  /lib/firmware/ath10k/QCA4019/hw1.0/board-2.bin.
* adds new firmware firmware-6.bin_RM.4.4.1.c1-00037-QCARMSWP-1 for
  QCA6174 hw3.0

Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2018-02-11 16:33:00 +01:00
Zoltan HERPAI
01020bc74d firmware: add microcode package for Intel
Compiling the Intel microcode package results in a
microcode.bin and a microcode-64.bin. As we can
decide based on the subtarget which should be used,
we'll only split the required .bin file with
iucode-tool.

x64 will get the intel-microcode-64.bin
All other variants will get intel-microcode.bin

The microcodes will be updated from preinit via a common
script - that's the earliest place where we can do it.

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2018-02-11 14:39:21 +01:00
Zoltan HERPAI
8fb3476345 firmware: add microcode package for AMD
Use the Debian repository for sourcing the ucode files.

Current (20171205) includes support for fam17h CPUs already.

The microcodes will be updated from preinit via a common
script - that's the earliest place where we can do it.

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2018-02-11 14:39:18 +01:00
Christian Lamparter
51dd8f3875 ipq-wifi: align AVM FRITZ!Box 4040's board-2.bin package
This patch renames the AVM FRITZ!Box 4040's board-2.bin
file and package to match the 'vendor_product' format.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-01-18 21:21:11 +01:00
Christian Lamparter
8d755ef052 firmware: ath10k-firmware: update QCA988x firmware to 10.2.4-1.0-00033
This patch updates ath10k-firmware to use the
firmware-5.bin_10.2.4-1.0-00033 firmware for the QCA988x.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-01-18 21:21:11 +01:00
Christian Lamparter
f6a8505de0 firmware: ath10k-firmware: update QCA9887 firmware to 10.2.4-1.0-00033
This patch updates ath10k-firmware to use the
firmware-5.bin_10.2.4-1.0-00033 firmware for the QCA9887.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-01-18 21:21:11 +01:00
Christian Lamparter
2d3a73afc4 firmware: ath10k-firmware: update QCA9888 firmware to 10.4-3.4-00104
This patch updates ath10k-firmware to use the
firmware-5.bin_10.4-3.4-00104 firmware for the QCA9888.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-01-18 21:21:11 +01:00
Christian Lamparter
da5312d06e firmware: ath10k-firmware: update QCA9984 firmware to 10.4-3.4-00104
This patch updates ath10k-firmware to use the
firmware-5.bin_10.4-3.4-00104 firmware for the QCA9984.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-01-18 21:21:11 +01:00
Christian Lamparter
e0184fd0d5 firmware: ath10k-firmware: update QCA4019 firmware to 10.4-3.4-00104
This patch updates ath10k-firmware to use the
firmware-5.bin_10.4-3.4-00104 firmware for the QCA4019.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-01-18 21:21:11 +01:00
Christian Lamparter
280a7d3948 firmware: ath10k-firmware: update to 2017-12-20
This update automatically includes a new firmware for the QCA6174:
firmware-6.bin_WLAN.RM.4.4.1-00079-QCARMSWPZ-1

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-01-18 21:21:11 +01:00
Sven Eckelmann
28b2a8cb82 ipq-wifi: add board-2.bin for OpenMesh A42
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2018-01-13 07:58:39 +01:00
Mathias Kresin
c3d9fe96dc ipq806x: drop partitial supported boards
There are only artifacts for these boards in our tree and not even
partial support.

Drop teh stale files.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-13 07:33:02 +01:00
Yangbo Lu
ab8da4d285 layerscape: add byte_swap.py script for ls-rcw package
This patch is to add a byte_swap.py script for rcw bin
byte swapping instead of using tclsh.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2017-12-26 23:30:59 +01:00
Yangbo Lu
5741835ed4 layerscape: fix PKG_BUILD_DIR for packages
PKG_BUILD_DIR was defined with quoting PKG_VERSION in
layerscape package makefiles. Now PKG_VERSION has been
removed from these makefiles. When PKG_BUILD_DIR quotes
PKG_VERSION, '=' should be used instead ':=' to make
sure PKG_VERSION has been defined in common makefile.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2017-12-26 23:30:59 +01:00
Hauke Mehrtens
dda2229c52 layerscape: fix package download
The git hash was changed for multiple layerscape packages without
changing the version number. The LEDE build system will not download the
packages again if the old version is already there and so some people
and the build bots are using wrong version of some packages. Use
PKG_SOURCE_DATE instead of PKG_VERSION to generate packages with the
date and the first charterers of the git hash. This will change the file
name and make the build system download them again, also if in future
the git hash is changed the file name will change and trigger a new
download.

This should fix a problem spotted by build bot.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-12-21 10:02:16 +01:00
Christian Lamparter
96b485ec7a firmware: ath10k-firmware: update QCA4019 firmware to 10.4-3.2.1-00058
This patch updates ath10k-firmware to use the
firmware-5.bin_10.4-3.2.1-00058 firmware for the QCA4019.

Cc: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2017-12-08 19:54:14 +01:00
Ted Hess
b83c32511e layerscape: rename firmware packages to avoid name collisions
layerscape firmware package names collide with existing package contributions.
Ex: layerscape mc and midnight-commander(mc) are in conflict.

Firmware packages: mc, ppa, rcw and dpl are renamed to ls-mc, ls-ppa, ls-rcw
and ls-dpl respectively.

Signed-off-by: Ted Hess <thess@kitschensync.net>
2017-12-02 10:38:08 -05:00
Hauke Mehrtens
9cfcd49735 kernel: e100: take e100 firmware from linux-firmware repository
The firmware directory in the Linux kernel was removed in kernel 4.14,
take the e100 firmware files now from the linux-firmware repository
instead. To do so create the new package e100-firmware. This will also
work with older kernel versions.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-11-22 22:37:05 +01:00
Christian Lamparter
5e6792eab4 wireless-regdb: fix PKG_MIRROR_HASH
make check complains about PKG_MIRROR_HASH of the wireless-regdb package:

WARNING: PKG_MIRROR_HASH does not match wireless-regdb-2017-10-20-4343d359.tar.xz
hash 5f5b669f32ae36cb65b1d99efbbbfd42c2983cda32f6448346e3e54ffaba3889

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2017-11-22 13:07:48 +01:00
Bjørn Mork
73e8fcf894 linux-firmware: add IO Edgeport USB Serial firmware
Preparing for kernel versions without firmware.

Signed-off-by: Bjørn Mork <bjorn@mork.no>
2017-11-16 22:56:54 +01:00
Felix Fietkau
a8d751c243 wireless-regdb: add package containing the wireless regulatory database
Installs to /lib/firmware for newer cfg80211 versions

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-11-16 15:23:32 +01:00
Yangbo Lu
2b1ec44dbd layerscape: add ls1012afrdm device support
The QorIQ FRDM-LS1012A Board is an ultra-low-cost
development platform for QorIQ LS1012A Series Network
Processors built on ARM Cortex-A53 processor.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2017-11-10 23:00:49 +01:00
Yangbo Lu
5b8639f02e layerscape: add ppa firmware package
This patch is to add PPA (The Primary Protected Application)
package and also enable it for all layerscape devices.
LSDK github provides ppa source code git tree, but it
only could be compiled with 64-bit toolchain. For 32-bit
devices, there was no method to use it.
https://github.com/qoriq-open-source/ppa-generic

This patch is to directly use a private ppa binary tree for
both 32-bit and 64-bit devices.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2017-11-10 23:00:49 +01:00
Yangbo Lu
82fbca8aaa layerscape: support LSDK ppfe
This patch is to use ppfe git tree on LSDK github
instead of private git tree, and support the latest
ppfe on ls1012ardb.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2017-11-10 23:00:49 +01:00
Yangbo Lu
1552dd01d9 layerscape: use 1GHz CPU fequency for ls1012ardb
Used 1GHz CPU fequency for ls1012ardb instead of 800MHz.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2017-11-10 23:00:47 +01:00
Yangbo Lu
b915ac8ce2 layerscape: update rcw to LSDK-17.09-update-103017 tag
Updated rcw to LSDK-17.09-update-103017 tag.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2017-11-10 23:00:47 +01:00
Yangbo Lu
47cff4cf5f layerscape: support all-in-one firmware for ls1088ardb/ls2088ardb
Suppport all-in-one firmware for ls1088ardb/ls2088ardb by
integrating u-boot/rcw/mc/dpl/restool.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2017-11-10 23:00:47 +01:00
Yangbo Lu
1e0276a39a layerscape: add dpl firmware package
This patch is to add data path layout files for the
second generation Data Path Acceleration Architecture.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2017-11-10 23:00:47 +01:00
Yangbo Lu
71a1df796e layerscape: add mc firmware package
This patch is to add package support for Management
Complex Firmware for the second generation Data Path
Acceleration Architecture.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2017-11-10 23:00:47 +01:00
Yangbo Lu
85e0d259d2 layerscape: move fman/rcw/ppfe packages to layerscape/
This patch is to create a layerscape directory for all
firmware packages of layerscape.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2017-11-10 23:00:47 +01:00
Henryk Heisig
f774d68fff ath10k-firmware: qca9888 firmware: remove board.bin
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2017-10-27 00:45:32 +02:00
Ben Whitten
76662637fa linux-firmware: add ath6k firmware to package
Systems which include the ath6k chipset need to have the firmware included
in the image.

Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
2017-10-15 00:24:21 +02:00