This patch removes CONFIG_MTD_SPI_NOR_USE_4K_SECTORS from the default
symbols for the ath79/mikrotik target.
MikroTik devices hold some of their user-configurable settings in the
soft_config partition, which is typically sized 4 KiB, of the SPI NOR
flash memory. Previously, in the ar71xx target, it was possible to use
64 KiB erase sectors but also smaller 4 KiB ones when needed. This is
no longer the case in ath79 with newer kernels so, to be able to write
to these 4 KiB small partitions without erasing 60 KiB around, the
CONFIG_MTD_SPI_NOR_USE_4K_SECTORS symbol was added to the defaults.
However, this ended up making sysupgrade images which were built with
64 KiB size blocks not to keep settings (e.g., the files under
/etc/config/) over the flashing process.
Using 4 KiB erase sector size on the sysupgrade images (by setting
BLOCKSIZE = 4k) allows keeping settings over a flashing process, but
renders the process terribly slow, possibly causing a user to
mistakenly force a manual device reboot while the process is still on-
going. Instead, ditching the 4 KiB erase sectors for the default
64 KiB erase size provides normal SPI write speed and sysupgrade times,
at the expense of not being able to modify the soft_config partition
(which is rarely a required thing).
An OpenWrt patch for MTD_SPI_NOR_USE_4K_SECTORS_LIMIT may once have
allowed to use different per-partition erase sector sizes. Due to
changes on recent kernels it now only works on a per-device basis.
Also, partial eraseblock write can be performed in ath79 with kernels
5.4 and lower, by copying the blocks from the 64 KiB, erasing the whole
sector and restoring those blocks not meant to be modified. A kernel
bump had that patch broken for a long time, but got fixed in bf2870c.
Note: the settings in the soft_config partition can be reset to their
defaults by holding the reset button for 5 seconds (and less than 10
seconds) at device boot.
Fixes: FS#3492 (sysupgrade […] loses settings...)
Fixes: a66eee6336 (ath79: add mikrotik subtarget)
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
(cherry picked from commit 68d91f08ed)
Changes from 4.7.0:
Fix one high (OCSP verification issue) and two low vulnerabilities
Improve compatibility layer
Other improvements and fixes
For detailed changes refer to https://github.com/wolfSSL/wolfssl/releases
Signed-off-by: Ivan Pavlov <AuthorReflex@gmail.com>
(cherry picked from commit 7d92bb0509)
[Added patch to allow compilation with libtool 2.4]
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Backport upstream patch to fix build with GCC 10 on 32 x86 targets.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
(cherry picked from commit 718a4f4780)
This fixes a kernel build problem.
The removed parts of the patch are already applied upstream.
Fixes: b4ed8a9275 ("kernel: bump 5.4 to 5.4.154")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 9501ce909f)
They're preferred terminal descriptions for tmux, with additional support to
some special characters and italic fonts. More info can be found at:
https://github.com/tmux/tmux/wiki/FAQ
Fixes: FS#3404
Signed-off-by: Jitao Lu <dianlujitao@gmail.com>
(cherry picked from commit 917126ff4c)
The terminfo is required by the popular terminal multiplexer screen and
tmux, offer it by default as the size impact is minimal with 885 Bytes.
Signed-off-by: Paul Spooren <mail@aparcar.org>
(cherry picked from commit 6a6b5a677e)
The terminfo files were all in one row which is terrible to read.
Split them over multiple lines to improve readability.
Signed-off-by: Paul Spooren <mail@aparcar.org>
(cherry picked from commit 75ea474b90)
isl.gforge.inria.fr has been dead since early this month [1]. Switch to
libisl.sourceforge.io for the time being.
[1] https://groups.google.com/g/isl-development/c/JGaMo2VUu_8
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
(cherry picked from commit dd0ad9b661)
Add in a fix for 160Mhz dfs on 5.10 and higher.
Add support for 5.13 and 5.15 kernels.
Add of_get_mac_address support for 5.15 driver.
Signed-off-by: Andrew Robbins <andrew@robbinsa.me>
(cherry picked from commit 1d2bc94f78)
"Alternate certification chains, as oppossed to requiring full chain
validataion. Certificate validation behavior is relaxed, similar to
openssl and browsers. Only the peer certificate must validate to a trusted
certificate. Without this, all certificates sent by a peer must be
used in the trust chain or the connection will be rejected."
This fixes e.g. uclient-fetch and curl connecting to servers using a Let's
Encrypt certificate which are cross-signed by the now expired
DST Root CA X3, see [0].
This is the recommended solution from upstream [1].
The binary size increases by ~12.3kb:
1236160 staging_dir/target-mipsel_24kc_musl/usr/lib/libwolfssl.so.4.8.1.39c36f2f
1248704 staging_dir/target-mipsel_24kc_musl/usr/lib/libwolfssl.so.4.8.1.39c36f2f
[0] https://github.com/openwrt/packages/issues/16674
[1] https://github.com/wolfSSL/wolfssl/issues/4443#issuecomment-934926793
Signed-off-by: Andre Heider <a.heider@gmail.com>
[bump PKG_RELEASE]
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 28d8e6a871)
1. Add support for Marvell CN9130 SoC
2. Add support for CP115,and create an armada-cp11x.dtsi file which will be used to instantiate both CP110 and CP115
3. Add support for AP807/AP807-quad,AP807 is a major component of CN9130 SoC series
4. Drop PCIe I/O ranges from CP11x file and externalize PCIe macros from CP11x file
Signed-off-by: Ian Chang <ianchang@ieiworld.com>
(cherry picked from commit c98ddf0f01)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
While the binary `python3.10` is correctly detected by the build system
the default `python3` binary is currently not detected if pointing to a
Python 3.10 installation.
Fix this by extending the grep regex.
Signed-off-by: Paul Spooren <mail@aparcar.org>
(cherry picked from commit 56ea2bf2ee)
Modifying PHY capabilities in the probe function broke with upstream
commit 92ed2eb7f4b7 ("net: phy: probe the PHY before determining the
supported features").
AR8316 switches only support 10/100 Mbit/s link modes because of this
change.
Provide a get_features method for the PHY driver, so Gigabit link mode
will be advertised to link partners again.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 766e0f584a)
Fedora 35 contains Python 3.10 as default version. Make use of it.
Signed-off-by: Marcin Juszkiewicz <marcin@juszkiewicz.com.pl>
[fix commit subject]
Signed-off-by: Paul Spooren <mail@aparcar.org>
(cherry picked from commit e1c03ca185)
Fix Fedora 34/35 issue where 'which' detection of 'which' wasn't working
because Fedora use alias and proc
Fixup of fca5ad55d2 prereq-build: fix `which` detection on Fedora
Reported-by: Jani Partanen <rtfm@iki.fi>
Suggest-by: Etienne Champetier <champetier.etienne@gmail.com>
Tested-by: Georgi Valkov <gvalkov@abv.bg>
Signed-off-by: Paul Spooren <mail@aparcar.org>
(cherry picked from commit 0d1ebf0d6d)
Make the organization (O=) of the cert configurable via uci. If not
configured, use a combination of "OpenWrt" and an unique id like it was
done before.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
(cherry picked from commit 2c6c1501af)
The official Plasma Cloud firmware adjusted the BDFs to contain new
conformance test limits and target power values. These should be imported
to avoid emissions outside the allowed limits.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
(cherry picked from commit e0721608f9)
In hostapd_ubus_add_bss(), ubus objects are not registered for mesh
interfaces. This provokes a segfault when accessing the ubus object in
mesh deinit.
This commit adds the same condition to hostapd_ubus_free_bss() for
discarding those mesh interfaces.
Signed-off-by: Jesus Fernandez Manzano <jesus.manzano@galgus.net>
(cherry picked from commit 5269c47e8d)
The rockchip platform supports squashfs SD card images. However, the
resulting image is not padded to completely fill the rootfs partition.
Because of that, the f2fs overlay might not be erased, resulting in
uci-defaults not bing executed or the configuration not being erased,
even though drop config was selected.
Modify the image generation process so the image is padded to cover the
entire root filesystem partition.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit b56f7407d9)
Takimata reported on the OpenWrt forum in thread [0], that his
MyBook Live Duo wasn't booting OpenWrt 21.02 after upgrading
from the previous OpenWrt 19.07.
The last logged entries on his console
|[ 0.531599] sata1-regulator GPIO handle specifies active low - ignored
|[ 0.538391] sata0-regulator GPIO handle specifies active low - ignored
|[ 0.759791] ata2: SATA link down (SStatus 0 SControl 300)
|[ 0.765251] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
|[ 5.909555] ata1.00: qc timeout (cmd 0xec)
|[ 5.913656] ata1.00: failed to IDENTIFY (I/O error, err_mask=0x4)
|[ 6.231757] ata1: SATA link down (SStatus 0 SControl 300)
This extract clearly showed that the HDD on which OpenWrt is installed,
simply disappeared after the SATA power regulators had been initialized.
Since the device-tree regulators haven't changed since the OpenWrt 19.07
days this will require further investigation on the snapshot/master/trunk
branch.
For the time being, it was requested to just delete the nodes so,
the device will boot again. Which unfortunately, will have to wait
until 21.02.1 is released.
He also confirmed that the My Book Live Single wasn't affected.
It works with or without this change.
[0] <https://forum.openwrt.org/t/21-02-0-and-snapshot-fail-to-boot-on-my-book-live-duo/106585>
Reported-by: Takimata (forum.openwrt.org/u/takimata)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The minew g1-c is a smart home gateway / BLE gateway.
A Nordic nRF52832 is available via USB UART (cp210x) to support BLE.
The LED ring is a ring of 24x ws2812b connect to a generic GPIO (unsupported).
There is a small LED which is only visible when the device is open which
will be used as LED until the ws2812b is supported.
The board has also a micro sdcard/tfcard slot (untested).
The Nordic nRF52832 exposes SWD over a 5pin header (GND, VCC, SWD, SWC, RST).
The vendor uses an older OpenWrt version, sysupgrade can be used via
serial or ssh.
CPU: MT7628AN / 580MHz
RAM: DDR2 128 MiB RAM
Flash: SPI NOR 16 MiB W25Q128
Ethernet: 1x 100 mbit (Port 0) (PoE in)
USB: USB hub, 2x external, 1x internal to USB UART
Power: via micro usb or PoE 802.11af
UART: 3.3V, 115200 8n1
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
The board data file for the Plasma Cloud PA2200 is not part of the default
board-2.bin which is shipped by ath10k-board-qca4019. A typo in the device
package name resulted in a not correctly selected package for the device
specific board-2.bin. The wifi driver has therefore loaded the wrong
calibration information into the wifi chip.
Fixes: 4871fd2616 ("ipq40xx: add support for Plasma Cloud PA2200")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
(cherry picked from commit c7e9335e4c)
The board data file for the Plasma Cloud PA1200 is not part of the default
board-2.bin which is shipped by ath10k-board-qca4019. A typo in the device
package name resulted in a not correctly selected package for the device
specific board-2.bin. The wifi driver has therefore loaded the wrong
calibration information into the wifi chip.
Fixes: ea5bb6bbfe ("ipq40xx: add support for Plasma Cloud PA1200")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
(cherry picked from commit d0ffc17535)
The board data file for the EnGenius EMR3500 is not part of the default
board-2.bin which is shipped by ath10k-board-qca4019. As result, the wrong
calibration information will be loaded into the wifi chip.
Fixes: 3f61e5e1b9 ("ipq40xx: add support for EnGenius EMR3500")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
(cherry picked from commit 14bd392a1c)
The board data file for the EnGenius EMD1 is not part of the default
board-2.bin which is shipped by ath10k-board-qca4019. As result, the wrong
calibration information will be loaded into the wifi chip.
Fixes: 51f3035978 ("ipq40xx: add support for EnGenius EMD1")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
(cherry picked from commit d9f4a4280e)
This patch fixes the forwarding behavior of bridge in bridge
configurations with DSA.
Without it, the configuration of the upper bridge might overwrite
settings of the lower bridge. For example, a vlan-aware bridge
with DSA interfaces in it might be offloaded to the DSA hardware. If the
bridge interface itself gets slave of a different bridge without vlan
filtering, the vlan filtering setting of the lower bridge is overwritten
by the upper bridge, which results in an incorrect hardware
configuration.
This was backported from kernel 5.7.
Ref: https://lore.kernel.org/netdev/20191222192235.GK25745@shell.armlinux.org.uk/
Fixes: FS#3996
Signed-off-by: Fabian Bläse <fabian@blaese.de>
(cherry picked from commit c50ece58c4)
These options are selectable when some of the kernel debug options like
KERNEL_SOFTLOCKUP_DETECTOR are selected.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 1a3b3dc797)
The LOCKUP_DETECTOR configuration option split into the
SOFTLOCKUP_DETECTOR and HARDLOCKUP_DETECTOR configuration option some
time ago. The HARDLOCKUP_DETECTOR option is only working on some
architectures, but SOFTLOCKUP_DETECTOR should work everywhere. Replace
KERNEL_LOCKUP_DETECTOR with KERNEL_SOFTLOCKUP_DETECTOR.
LOCKUP_DETECTOR will be selected by SOFTLOCKUP_DETECTOR automatically.
Fixes: b951f53fba ("build: Add additional kernel debug options")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit d27f6e2c5d)
At this moment kernel partition in Linksyses EA3500/E4200/EA4500 is
ended before start of rootfs partition. It was introduced in 9808b9ae02
and it broke easy revert to stock. Sysupgrade, when OFW is used, write
whole stock image to kernel partition. Most likeley image will be bigger
than small kernel partition and it make stock system invalid.
This patch change size of kernel partitions and now it overlaps rootfs.
Revert to stock will be possible again.
Fixes: 9808b9ae02 ("kirkwood: switch to kernel 4.9")
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
This patch has been carried since introduction throughout every kernel
major bump and no one has tested if the later kernels improved the
situation. The Armada 3720 SoC can only process GbE interrupts on Core 0
and this is already limited in all stable kernels, so ditch this
workaround for 64 bit SoCs.
Ref: https://git.kernel.org/torvalds/c/cf9bf871280d
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
(cherry picked from commit cbdd2b62e4)
The Onion Omega is a hardware development platform with built-in WiFi.
https://onioniot.github.io/wiki/
Specifications:
- QCA9331 @ 400 MHz (MIPS 24Kc Big-Endian Processor)
- 64MB of DDR2 RAM running at 400 MHz
- 16MB of on-board flash storage
- Support for USB 2.0
- Support for Ethernet at 100 Mbps
- 802.11b/g/n WiFi at 150 Mbps
- 18 digital GPIOs
- A single Serial UART
- Support for SPI
- Support for I2S
Flash instructions:
The device is running OpenWrt upon release using the ar71xx target.
Both a sysupgrade
and uploading the factory image using u-boots web-UI do work fine.
Depending on the ssh client, it might be necessary to enable outdated
KeyExchange methods e.g. in the clients ssh-config:
Host 192.168.1.1
KexAlgorithms +diffie-hellman-group1-sha1
The stock credentials are: root onioneer
For u-boots web-UI manually configure `192.168.1.2/24` on your computer,
connect to `192.168.1.1`.
MAC addresses as verified by OEM firmware:
2G phy0 label
LAN eth0 label - 1
LAN is only available in combination with an optional expansion dock.
Based on vendor acked commit:
commit 5cd49bb067 ("ar71xx: add support for Onion Omega")
Partly reverts:
commit fc553c7e4c ("ath79: drop unused/incomplete dts")
Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me>
(cherry picked from commit d98738b5c1)
This version fixes two vulnerabilities:
- SM2 Decryption Buffer Overflow (CVE-2021-3711)
Severity: High
- Read buffer overruns processing ASN.1 strings (CVE-2021-3712)
Severity: Medium
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
(cherry picked from commit 7119fd32d3)
Backport a patch from upstream U-Boot to fix the compile with host GCC 10.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 8d143784cb)
Backport a patch from upstream U-Boot to fix the compile with host GCC 10.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit a1034afba8)
The bootloader will look for a configuration section named ap.dk01.1-c2
in the FIT image. If this doesn't exist, the device won't boot.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
(cherry picked from commit a43da1be43)
