Commit Graph

940 Commits

Author SHA1 Message Date
Marek Lindner
ea5bb6bbfe ipq40xx: add support for Plasma Cloud PA1200
Device specifications:

* QCA IPQ4018
* 256 MB of RAM
* 32 MB of SPI NOR flash (w25q256)
  - 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
  - QCA4019 hw1.0 (SoC)
  - requires special BDF in QCA4019/hw1.0/board-2.bin with
    bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=PlasmaCloud-PA1200
* 2T2R 5 GHz
  - QCA4019 hw1.0 (SoC)
  - requires special BDF in QCA4019/hw1.0/board-2.bin with
    bus=ahb,bmi-chip-id=0,bmi-board-id=17,variant=PlasmaCloud-PA1200
* 3x GPIO-LEDs for status (cyan, purple, yellow)
* 1x GPIO-button (reset)
* 1x USB (xHCI)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
  - phy@mdio4:
    + Label: Ethernet 1
    + gmac0 (ethaddr) in original firmware
    + used as LAN interface
  - phy@mdio3:
    + Label: Ethernet 2
    + gmac1 (eth1addr) in original firmware
    + 802.3af/at POE(+)
    + used as WAN interface
* 12V/24V 1A DC

Flashing instructions:

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.

Signed-off-by: Marek Lindner <marek.lindner@kaiwoo.ai>
[sven@narfation.org: prepare commit message, rebase, use all LEDs, switch
to dualboot_datachk upgrade script, use eth1 as designated WAN interface]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
2020-12-22 19:11:50 +01:00
Sven Eckelmann
5fc28ef479 ath79: Add support for Plasma Cloud PA300
Device specifications:

* Qualcomm/Atheros QCA9533 v2
* 650/600/217 MHz (CPU/DDR/AHB)
* 64 MB of RAM
* 16 MB of SPI NOR flash (mx25l12805d)
  - 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2x 10/100 Mbps Ethernet
* 2T2R 2.4 GHz Wi-Fi
* multi-color LED (controlled via red/green/blue GPIOs)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x fast ethernet
  - eth0
    + Label: Ethernet 1
    + 24V passive POE (mode B)
    + used as WAN interface
  - eth1
    + Label: Ethernet 2
    + 802.3af POE
    + builtin switch port 2
    + used as LAN interface
* 12-24V 1A DC
* internal antennas

Flashing instructions:

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.

Signed-off-by: Sven Eckelmann <sven@narfation.org>
2020-12-22 19:11:50 +01:00
Sven Eckelmann
3599ea5263 images: Fix sysupgrade.tar for devices with NOR flash
The NOR flash rootfs images stored in a sysupgrade.tar must end with the
JFFS2 marker. Otherwise, devices like OpenMesh A42/A62 are not able to
calculate the md5sum of the fixed squashfs part and store it inside the
u-boot-env.

But the commit ee76bd11bb ("images: fix boot failures on NAND with small
sub pages") adds up to 1020 0x00 bytes after the 0xdead0de EOF marker. The
calculated md5sum will be wrong due do this change and u-boot will fail to
boot the newly flashed device with a message like:

  Validating MD5Sum of 'vmlinux'...
  Passed!
  Validating MD5Sum of 'rootfs'...
  Failed!
      583a1b7b54b8601efa64ade42742459b != 8850ee812dfd7638e94083329d5d2781

  Data validation failed!

and boot the old image again.

Since the original change should not change the behavior of NOR images,
just check for the deadc0de marker at the end of the squashfs-jffs2 image
do avoid the problematic behavior for these images.

Fixes: ee76bd11bb ("images: fix boot failures on NAND with small sub pages")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
2020-12-22 19:11:50 +01:00
Sven Eckelmann
a4c30d9399 scripts/om-fwupgradecfg-gen.sh: Generate checksum over whole squashfs
The rootfs is padded to the full block size by padjffs2 and a 4 byte magic
value ("deadc0de") is added to the end. On first boot, the JFFS2 is
replacing the "deadc0de" marker when the rootfs_data is initialized.

The static part of the rootfs is therefore $rootfs_size - 4 and not
$rootfs_size - 262144 - 4.

Signed-off-by: Sven Eckelmann <sven@narfation.org>
2020-12-22 19:11:50 +01:00
Sven Eckelmann
7c75eaadfc scripts/om-fwupgradecfg-gen.sh: Drop block alignment code
The padding and block alignment is handled by the image build script and
doesn't need to be duplicated in the fwupgrade.cfg build script.

Signed-off-by: Sven Eckelmann <sven@narfation.org>
2020-12-22 19:11:50 +01:00
INAGAKI Hiroshi
fdcdbdfdef scripts: add -N option to mkhash for printing without newline
Added "-N" option, it allow printing hash(es) without newline.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2020-12-22 19:11:50 +01:00
Paul Spooren
bc0ffff36a build/json: add filesystem information
Some images are created using different filesystems, most popular
squashfs and ext4. To allow downstream projects to distinguesh between
those, add the `filesystem` information to created json files.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2020-12-13 22:07:52 -10:00
Karel Kočí
a3e5b24d43 scripts/feeds: fix preference of package install
The previous behavior prefered same feed for dependent packages as
initial package. This caused inconsitency in installation of packages.
The difference was if two feeds provide same package (different version)
there was different result if you executed install for that specific
version compared to install for package depending on it from different
feed.

This ensures that preferred feed is propagated without change and
selected feed is used only really for package it was selected for.

Signed-off-by: Karel Kočí <karel.koci@nic.cz>
2020-12-09 23:25:05 -10:00
Brian Norris
7f285d0b43 scripts/feeds: warn when skipping core package override
Otherwise, a n00b like myself can get quite confused when moving a
package from core to feeds, for example.

(Hint: one *really* needs to clear out the tmp/info/.packageinfo...
entries for the stale package, but '-f' works as well.)

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2020-12-09 11:30:07 -10:00
Piotr Stefaniak
1db9b5b6d6 build: mkhash on FreeBSD
Apply patch from
https://bugs.openwrt.org/index.php?do=details&task_id=971
in order to make it easier to build OpenWRT on FreeBSD.

Signed-off-by: Piotr Stefaniak <pstef@freebsd.org>
2020-11-27 18:01:22 -10:00
Petr Štetiar
52a5d0d27f download.pl: properly cleanup intermediate .hash file
It seems like after a build the /dl dir seems to now contain a .hash
file for each source file due to inproper cleanup so fix it by removing
those intermediate files before leaving the download action.

Fixes: 4e19cbc553 ("download: handle possibly invalid local tarballs")
Reported-by: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-11-27 22:27:08 +01:00
Petr Štetiar
4e19cbc553 download: handle possibly invalid local tarballs
Currently it's assumed, that already downloaded tarballs are always
fine, so no checksum checking is performed and the tarball is used even
if it might be corrupted.

From now on, we're going to always check the downloaded tarballs before
considering them valid.

Steps to reproduce:

 1. Remove cached tarball

   rm dl/libubox-2020-08-06-9e52171d.tar.xz

 2. Download valid tarball again

   make package/libubox/download

 3. Invalidate the tarball

   sed -i 's/PKG_MIRROR_HASH:=../PKG_MIRROR_HASH:=ff/' package/libs/libubox/Makefile

 4. Now compile with corrupt tarball source

   make package/libubox/{clean,compile}

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-11-27 14:46:13 +01:00
Hannu Nyman
2b1d92f134 scripts/feeds: silence git warning by selecting pull style
Silence the warning in git 2.27 about undefined fast-forward style
in git pull. Define "ff-only" as the style.

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
2020-11-26 19:29:18 -10:00
Paul Spooren
0c87304d2b scripts: add size_compare.sh
As package size changes are a continuous topic on the mailing list this
scripts helps developers to compare their local package modifications
against latest upstream.

The script downloads the latest package indexes based on env variables
or the `.config` file. The script compares the actual installed size
(data.tar.gz) or the IPK package size.

An example output is found below:

```
user@dawn:~/src/openwrt/openwrt$ ./scripts/size_compare.sh
Compare packages of ath79/tiny/mips_24kc:
dropbear busybox iw ubus

Checking configuration difference
  % Total    % Received % Xferd  Average Speed   Time    Time     Time  Current
                                 Dload  Upload   Total   Spent    Left  Speed
100   554  100   554    0     0    336      0  0:00:01  0:00:01 --:--:--   336

 --- start config diff ---
--- /tmp/config.DDjwVh-LOCAL	2020-11-23 09:08:28.913203068 -1000
+++ /tmp/config.DDjwVh-UPSTREAM	2020-11-23 09:08:36.369240887 -1000
@@ -1,5 +1,9 @@
+CONFIG_ALL_KMODS=y
+CONFIG_ALL_NONSHARED=y
 CONFIG_AUTOREBUILD=y
+CONFIG_AUTOREMOVE=y
--- 8< ---
 CONFIG_BINARY_FOLDER=""
+CONFIG_BUILDBOT=y
+CONFIG_TARGET_ALL_PROFILES=y
 CONFIG_TARGET_ROOTFS_DIR=""
 CONFIG_USE_SSTRIP=y
 CONFIG_USE_UCLIBCXX=y
 --- end config diff ---

Checking installed size

Fetching latest package indexes...
  % Total    % Received % Xferd  Average Speed   Time    Time     Time  Current
                                 Dload  Upload   Total   Spent    Left  Speed
100 80634  100 80634    0     0  33499      0  0:00:02  0:00:02 --:--:-- 33485
  % Total    % Received % Xferd  Average Speed   Time    Time     Time  Current
                                 Dload  Upload   Total   Spent    Left  Speed
100 54082  100 54082    0     0  24252      0  0:00:02  0:00:02 --:--:-- 24252

Comparing package sizes...
Change 	Local	Remote 	Package
+271	51386	51115	base-files
+123	705241	705118	bnx2-firmware
+86	17209	17123	fstools
+22	47989	47967	procd
+21	208311	208290	busybox
+19	67181	67162	netifd

```

I plan to integrate this script into the CI so we have a summary how
sizes change over different architectures.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2020-11-24 18:18:48 -10:00
David Bauer
d369993898 scripts: download.pl: retry download using filename
With this commit, the download script will try downloading source files
using the filename instead of the url-filename in case the previous
download attempt using the url-filename failed.

This is required, as the OpenWrt sources mirrors serve files using the
filename files might be renamed to after downloading. If the original
mirror for a file where url-filename and filename do not match goes
down, the download failed prior to this patch.

Further improvement can be done by performing this only for the
OpenWrt sources mirrors.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-11-20 02:35:43 +01:00
Adrian Schmutzler
7e7470b517 scripts: add const_structs.checkpatch for checkpatch.pl
Kernel has separated the structs that are reported to be const in
checkpatch.pl into a file of its own, const_structs.checkpatch.

This file has been missing after the recent update of checkpatch.pl,
leading to the following message:

  No structs that should be const will be found - file
  '/data/openwrt/scripts/const_structs.checkpatch': No such file
  or directory

This commit adds the relevant file from v5.10-rc4.

Fixes: 086ee09bbc ("scripts: Update checkpatch.pl to 2020-06-11")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-11-18 21:50:58 +01:00
Adrian Schmutzler
6fdd4187e0 scripts: checkpatch.pl: suppress warnings about MAINTAINERS
The kernel expects changes to MAINTAINERS for all removed or added
files, printing warnings like:

  WARNING: added, moved or deleted file(s), does MAINTAINERS need updating?
  #828:
  deleted file mode 100644

Since this does not apply to "our" files in OpenWrt repo, this
warning should be disabled.

This can be achieved easiest by setting $reported_maintainer_file
to 1. While this is a hack that tricks the script into believing
the proper MAINTAINERS changes have been made, it's the easiest
solution as it does not require to touch any other code.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-11-18 21:50:53 +01:00
Felix Fietkau
184d735707 scripts/kconfig.pl: allow regex syntax in filtering out config entries
This will be used to filter out some autogenerated config values from
the kernel config files

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2020-11-13 13:17:53 +01:00
Paul Spooren
3c0357e7b4 scripts: add spelling.txt for checkpatch.pl
Running the updated checkpatch version with spelling.txt show that
spelling mistakes happen to everyone.

> /target/linux$ fd .*.patch | xargs ../../scripts/checkpatch.pl | rg spell
WARNING: 'usefull' may be misspelled - perhaps 'useful'?
WARNING: 'afecting' may be misspelled - perhaps 'affecting'?
WARNING: 'usefull' may be misspelled - perhaps 'useful'?
WARNING: 'afecting' may be misspelled - perhaps 'affecting'?
WARNING: 'begining' may be misspelled - perhaps 'beginning'?
WARNING: 'superflous' may be misspelled - perhaps 'superfluous'?
WARNING: 'multipe' may be misspelled - perhaps 'multiple'?
WARNING: 'recieves' may be misspelled - perhaps 'receives'?
WARNING: 'retreive' may be misspelled - perhaps 'retrieve'?
WARNING: 'tranfer' may be misspelled - perhaps 'transfer'?
WARNING: 'additonal' may be misspelled - perhaps 'additional'?
WARNING: 'accomodate' may be misspelled - perhaps 'accommodate'?
[...]

Signed-off-by: Paul Spooren <mail@aparcar.org>
2020-11-12 18:21:55 +01:00
Paul Spooren
66e87a1f38 scripts: checkpatch remove device-tree doc check
Remove checks for device tree documentation as the OpenWrt tree comes
withouth the ./Documentation folder.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2020-11-12 18:21:55 +01:00
Paul Spooren
086ee09bbc scripts: Update checkpatch.pl to 2020-06-11
Checkpatch grown in functionallity and we should make use of that. If
OpenWrt patches should be upstream material they should also be checked
based on upstream checkpatch.pl instead of 2013.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2020-11-12 18:21:55 +01:00
Paul Spooren
165f0b00cd build: store SOURCE_DATE_EPOCH in JSON info files
The source date epoch is the only reproducible date close to the actual
build date. It can be used for tooling like the firmware wizard to show
the image age.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2020-11-12 18:19:44 +01:00
Paul Spooren
fcd3e13779 scripts: mkhash fail on hashing a folder
mkhash currently returns the hash of an empty input when trying to hash
a folder. This can be missleading in caseswhere e.g. an env variable is
undefined which should contain a filename. `mkhash ./path/to/$FILE`
would exit with code 0 and return a legit looking checksum.

A better behaviour would be to fail with exit code 1, which imitates the
behaviour of `md5sum` and `sha256sum`.

To avoid hashing of folders the `stat()` is checked.

Hashing empty inputs result in the following checksums:
md5: d41d8cd98f00b204e9800998ecf8427e
sha256: e3b0c44298fc1c149afbf4c8996fb92427ae41e4649b934ca495991b7852b855

Signed-off-by: Paul Spooren <mail@aparcar.org>
2020-11-09 10:54:29 +00:00
Paul Spooren
fac98f1c54 scripts: mkhash fix return code handling
If hashing a file fails mkhash shouldn't just silently fail. Now check
after each call of `hash_file()` the return and exit early in case of
errors. The return value which was previously ignored and would always
return 0.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2020-11-09 10:54:29 +00:00
Paul Spooren
91a0dc5161 scripts: mkhash show -n option in usage
The -n option prints the filename of hashed files next to the calculated
checksum. Reflect that in the usage message.

user@dawn:~/src/openwrt/openwrt$ ./a.out md5 -n .config
eb06db36e7b6751cb18801945e46bf5d .config

Signed-off-by: Paul Spooren <mail@aparcar.org>
2020-11-09 10:52:19 +00:00
Petr Štetiar
4b7165722c scripts: bundle-libraries.sh: fix broken SDK compiler
Recent versions (> 5.33) of `file` report liblto_plugin.so as
executable:

 $ file liblto_plugin.so
 liblto_plugin.so.0.0.0: ELF 64-bit LSB pie executable ...

Which then leads to improper packaging of the plugin, resulting in the
broken compiler:

 configure: checking whether the C compiler works
 mips-openwrt-linux-musl/bin/ld: liblto_plugin.so: error loading plugin: liblto_plugin.so: invalid ELF header

As the LTO compiler plugin library is incorrectly packaged as SDK
executable:

 $ head -1 ~/staging_dir/toolchain...libexec/gcc/.../liblto_plugin.so
 #!/usr/bin/env bash

Fix this by filtering out shared libraries from the patching.

Ref: https://bugzilla.redhat.com/show_bug.cgi?id=1296868
Acked-by: Jo-Philipp Wich <jo@mein.io>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-11-02 08:39:49 +01:00
Petr Štetiar
f52aee0455 scripts/getver.sh: silence rev-list errors
Shallow copies are quite common on CI platforms nowadays, making REBOOT
tag unavailable, thus producing following confusing errors in the build
logs:

 fatal: Invalid revision range ee53a240ac902dc83209008a2671e7fdcf55957a..HEAD
 fatal: Invalid revision range ee53a240ac902dc83209008a2671e7fdcf55957a..0493d57e04774d47921a7d2014b567455d5dc16b

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-11-02 08:39:49 +01:00
Tony Ambardar
5b3ff53ebd scripts/qemustart: update malta to use MIPS64 R2 cpu
Explicitly set the QEMU cpu type and support the MIPS R2 ISA, for both
64-bit and 32-bit targets. The later previously supported MIPS R2 by
implicit default.

This is needed after commit 93608697f3 ("malta: update MIPS64 ISA to R2"),
otherwise booting malta images with scripts/qemustart will hang.

Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
2020-10-11 16:16:24 +02:00
Christian Lamparter
f6fbc39706 build: define PWM_SUPPORT arch feature flag
As the PWM has its own sub-system in the Linux kernel,
I think it should be handled in the same way as GPIO, RTC, PCI...

This patch introduces a specific feature flag "pwm" and the
"leds-pwm" kernel module as the first customer.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-09-25 19:32:33 +02:00
Christian Lamparter
fed1788689 scripts: mkits.sh make it possible to specify fdt@#
Some bootloaders are really keen on just one special
fdt in a multi-image fit image. This is a problem, because
currently this is fixed to "fdt@1".

This patch introduces a new device variable:
DEVICE_FDT_NUM that allows to specify the right
fdt number.

If the value is absent "1" will be chosen.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-09-25 19:32:33 +02:00
Paul Spooren
8be2eb3b9b scripts: update SPDX license names
SPDX moved from GPL-2.0 to GPL-2.0-only and from GPL-2.0+ to
GPL-2.0-or-later. Reflect that in the SPDX license headers.

Signed-off-by: Paul Spooren <mail@aparcar.org>
[adjust commit title, update remaining files]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-22 20:36:04 +02:00
Jo-Philipp Wich
4038c031cb scripts: ipkg-build: simplify uid/gid resolving
Use the prepared .packageusergroup file to lookup user and group names
when processing the passed file mode.

Also replace the various subshell/cut invocations with a sequence of
standard variable interpolations which fixes paths with embedded colons
as a side-effect.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2020-09-14 17:11:04 +02:00
Paul Spooren
51ec51871f build: add user/group ID resolve function
With the introduction of `./tmp/userids` the `ipkg-build` script can now
resolve values of "PKG_FILE_MODES", allowing users to set names rather
than numeric values.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2020-09-14 10:54:52 +01:00
David Bauer
fe82ea049e scripts: download.pl: fix indentation
Signed-off-by: David Bauer <mail@david-bauer.net>
2020-09-11 17:35:19 +02:00
Jo-Philipp Wich
10dbdeccfa scripts: bundle-libraries.sh: retain preloaded libraries
Since the introduction of fakeroot support, wrapped SDK executables might
be invoked from a shell that has libfakeroot.so preloaded.

Since we're using preloading as well in order to mangle argv[0] when
invoking the shipped ELF interpreter directly, we must take care of
preloading the already preloaded libraries as well, to avoid invoked
programs losing their fakeroot capabilities.

Extend the bundle-libraries.sh script to take any existing $LD_PRELOAD
into account when invoking the target ELF executable with a preloaded
runas.so library.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2020-09-10 14:24:50 +02:00
Paul Spooren
fd29f2bcd9 build: store granular timestamps in packages
With the new `SOURCE` argument of `get_source_date_epoch` it is possible
to set package timestamps based on actual package changes rather thane
$TOPDIR changes.

This commit adds a new variable PKG_SOURCE_DATE_EPOCH which is used by
the `ipkg` build script. As a fallback the existing SOURCE_DATE_EPOCH is
used or as last resort the current time.

The redundant checks for `.git/` and `.svn/` are removed.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2020-08-31 11:18:06 +01:00
Paul Spooren
a83b2af47f build: get_source_date_epoch allow external repos
The SOURCE_DATE_EPOCH variable is used to make builds reproducible even
if rebuild at different times. Instead of using the current timestamp,
the time of the last source change is used.

Created packages are `touch`ed with a specific timestamp so resulting
packages have the same checksums.

The `get_source_date_epoch.sh` script tries multiple ways (file, git,
hg) to determine the correct timestamp.

Until now the script would only consider the $TOPDIR instead of package
specific changes. Resulting in packages with same versions but different
timestamps, as $TOPDIR (openwrt.git) received changes not affecting
package versions. This results in warning/erros in `opkg` as the package
versions stay the same but checksums changed.

This commit adds an optional argument to get the `SOURCE_DATE_EPOCH` of
a specific path (e.g. package SOURCE) rather than the $TOPDIR. As a
consequence this allows granular but still reproducible timestamps.

As packages might be distributed over multiple repositories the check
for `.git/` becomes unfeasible. Instead tell `git` and `hg` to change
their working directories and automatically traverse the repo folder.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2020-08-31 11:18:06 +01:00
Paul Spooren
ae87e53e33 build: Fix Shellcheck for get_source_date_epoch.sh
If a `cd` to `TOPDIR` fails the script should quit.

Also unify `try_mtime` function by storing it in a variable.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2020-08-31 11:18:06 +01:00
Paul Spooren
353ce2e521 build: ipkg-build use fakeroot with PKG_FILE_MODES
The `ipkg-build` script converts a folder into a `opkg` installable
package. Until now it would use root:root for all packages and try to
preserve file modes.

This has the two drawbacks of packages want to add non-root files or add
SUID files, like the `sudo` package does.

To give more flexibility regarding file modes and avoid init script
hacks, a new variable called `PKG_FILE_MODES`. The variable contains a
list of files modes in the format `path:owner:group:mode`.

An example for the `sudo` package below:

```
PKG_FILE_MODES:=\
        /usr/bin/sudo:root:root:4755 \
        /etc/sudoers:root:root:0440
```

The `ipkg-build` now runs within a fakeroot environment to set any mode
and directly store it in the resulting `ipk` package archive.

Both options `-o` and `-g` are no longer required due to the introduction
of the more flexible `-m` options, which takes the `PKG_FILE_MODES` as
input.

Lastly the option `-c` is removed as it's unused within the script.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2020-08-31 11:13:12 +01:00
Jo-Philipp Wich
bf96eb55c8 Revert "scripts/download: add sources CDN as first mirror"
This reverts commit c737a9ee6a.

The source CDN has been discontinued in its current form and will take a
while to be reestablished. Even then it makes little sense to put a CDN
before other CDNs such as kernel.org, apache.org, sourceforge etc.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2020-08-24 15:55:14 +02:00
Paul Spooren
1fdf6b745c treewide: replace which with command -v
Fix shellcheck SC2230
> which is non-standard. Use builtin 'command -v' instead.

Using `command -v` is POSIX compliant while `which` is not.  Also to
mention, `command -v` is a shell builtin whereas `which` is a separate
busybox applet.

Once applied to everything concerning OpenWrt we can disable the busybox
feature `which` and save 3.8kB.

Acked-by: Stijn Tintel <stijn@linux-ipv6.be>
Signed-off-by: Paul Spooren <mail@aparcar.org>
[also replace cases in zram-swap]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-12 11:08:05 +02:00
Petr Štetiar
80d360202f scripts: remove checkpatch.sh
That file was added accidentally in v3 of the patch and I haven't
properly reviewed that patch before pushing it.

Fixes: 656b562aff ("scripts: Add Buildbot dump-target-info.pl script")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-08-04 14:25:44 +02:00
Paul Spooren
656b562aff scripts: Add Buildbot dump-target-info.pl script
The script comes from buildbot.git[0] and is used to print available
targets and architectures, which are then build.

As the buildbot clones openwrt.git anyway, the script might as well live
here to be used for other cases as well, e.g. determining what
architectures are available when building Docker containers or show
developers an overview which architectures are used by which target.

It's called with either the parameter `architectures` or `targets`,
showing architectures followed by supported targets or targets, followed
by the supported architectures:

$ ./scripts/dump-target-info.pl architectures
aarch64_cortex-a53 bcm27xx/bcm2710 mediatek/mt7622 mvebu/cortexa53 sunxi/cortexa53
aarch64_cortex-a72 bcm27xx/bcm2711 mvebu/cortexa72
...

$ ./scripts/dump-target-info.pl targets
apm821xx/nand powerpc_464fp
apm821xx/sata powerpc_464fp
...

In the future the the script could be removed from the buildbot
repository and maintained only here.

Rename `dumpinfo.pl` to `dump-target-info.pl` to improve verbosity of
filename.

[0]: https://git.openwrt.org/?p=buildbot.git;a=blob;f=scripts/dumpinfo.pl;h=aa97f8d60379076a41b968402e9337cea824ece5;hb=HEAD

Signed-off-by: Paul Spooren <mail@aparcar.org>
2020-08-04 09:28:39 +02:00
Adrian Schmutzler
b99623329c scripts/checkpatch.pl: fix README.md file name after rename
checkpatch.pl uses a list of files to detect the root OpenWrt
directory. This includes README, which has been renamed to
README.md in the previous commit.

Update the file name in checkpatch.pl to prevent errors like the
following when running the script:

   Must be run from the top-level dir. of a OpenWrt tree

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-02 15:51:39 +02:00
Adrian Schmutzler
1d5260cf72 build: add option to mark devices as BROKEN
By specifying "BROKEN := 1" or "BROKEN := y" for a device, it will be
hidden (and deselected) by default. By that, it provides a stronger
option to "disable" a device beyond just using DEFAULT := n.

To make these devices visible, just enable the BROKEN option in
developer settings as already implemented for targets and packages.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-30 21:49:07 +02:00
Paul Spooren
5b8b42c78b build,json: fix compatibility with Python 3.5
The f-string feature was introduced in Python 3.6. As Buildbots may run
on Debian 9, which comes per default with Python 3.5, this would cause
an issue. Instead of f-strings use the *legacy* `.format()` function.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2020-07-13 22:45:04 +02:00
Kevin Darbyshire-Bryant
8242c6de29 scripts/env: Fix 56f813674a scripts/env: use command -v instead of which
We don't need to see how git will be executed and it produces non silent
output on 'scripts/env diff' commands when there are no differences
unlike before.

Re-introduce original silent behaviour.

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2020-07-12 13:29:28 +01:00
Adrian Schmutzler
52cdd6185e scripts/mkits.sh: fix use of printf
Due to a line break, printf was accidentally called with three
arguments instead of two, causing a different output than before.

Fix it by splitting the printf command into two lines.

Fixes: 907053193a ("scripts/mkits.sh: replace echo -e with printf")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-11 18:46:53 +02:00
Petr Štetiar
dec9ae6d9e scripts/mkits.sh: fix remaining shellcheck warning
Fixes following shellcheck warning:

 In scripts/mkits.sh line 19:
 		 "-k kernel [-D name -d dtb] -o its_file" "$(basename $0)"
                                                                       ^-- SC2086: Double quote to prevent globbing and word splitting.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-07-11 14:42:32 +02:00
Rosen Penev
3d418dd51e scripts/mkits.sh: switch from bash to sh
This no longer needs bash.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2020-07-11 14:42:32 +02:00
Rosen Penev
7aefc85cab scripts/mkits.sh: fix improper string and array concatenation
Found with shellcheck.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2020-07-11 14:42:32 +02:00
Rosen Penev
765858f7ad scripts/mkits.sh: add missing quotes
Found with shellcheck.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2020-07-11 14:42:32 +02:00
Rosen Penev
907053193a scripts/mkits.sh: replace echo -e with printf
echo flags are not POSIX. printf does the same with added \n.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2020-07-11 14:42:32 +02:00
Petr Štetiar
92d7cedcad scripts/gen_image_generic.sh: fix more shellcheck warnings
Fixes following shellcheck warnings:

 In scripts/gen_image_generic.sh line 20:
 cyl=$(( (KERNELSIZE + ROOTFSSIZE) * 1024 * 1024 / (head * sect * 512)))
 ^-^ SC2034: cyl appears unused. Verify use (or export if used externally).
 --
 In scripts/gen_image_generic.sh line 34:
     [ -n "$PADDING" ] && dd if=/dev/zero of="$OUTPUT" bs=512 seek="$(($ROOTFSOFFSET + $ROOTFSSIZE))" conv=notrunc count="$sect"
                                                                       ^-----------^ SC2004: $/${} is unnecessary on arithmetic variables.
 --
 In scripts/gen_image_generic.sh line 35:
     mkfs.fat -n kernel -C "$OUTPUT.kernel" -S 512 "$(($KERNELSIZE / 1024))"
                                                       ^---------^ SC2004: $/${} is unnecessary on arithmetic variables.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-07-11 14:42:32 +02:00
Rosen Penev
aee169b06d scripts/gen_image_generic.sh: use /bin/sh
This has nothing bash specific.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2020-07-11 13:33:28 +02:00
Rosen Penev
3819337cdf scripts/gen_image_generic.sh: replace -o with if/&&
-o is not well defined.

Found with shellcheck.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2020-07-11 13:33:28 +02:00
Petr Štetiar
227e47b3ca scripts/env: fix remaining shellcheck warning
Fixes following shellcheck warning:

 In scripts/env line 25:
 	exit ${1:-1}
             ^-----^ SC2086: Double quote to prevent globbing and word splitting.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-07-11 13:33:28 +02:00
Rosen Penev
5b7cace9e3 scripts/env: use read -r instead of read
read mangles backslashes.

Found with shellcheck.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2020-07-11 13:33:28 +02:00
Rosen Penev
f80a540dbf scripts/env: exit in case of failure to cd
Found with shellcheck.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2020-07-11 13:33:28 +02:00
Rosen Penev
e68810ba53 scripts/env: replace \! with !
The latter is more standard. The former throws an error under
shellcheck.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2020-07-11 13:33:28 +02:00
Rosen Penev
56f813674a scripts/env: use command -v instead of which
Simpler and built in to the shell.

Found with shellcheck.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2020-07-11 13:33:28 +02:00
Huangbin Zhan
3caad5150c build: fix compatibility with python 3.6
On a system python3 is linked to python3.6, fail to perform json_overview_image_info
 and got `TypeError: __init__() got an unexpected keyword argument 'capture_output'`.
This patch emulate the behaviour on python 3.7+.

Signed-off-by: Huangbin Zhan <zhanhb88@gmail.com>
2020-07-07 19:47:24 +02:00
Sergio E. Nemirowski
ab26022cc1 build: mconf readme update
This updates mconf.c readme message to maintain less changes with
upstream and consistency with nconf.c

Signed-off-by: Sergio E. Nemirowski <sergio@outerface.net>
2020-07-07 19:47:24 +02:00
Sergio E. Nemirowski
8fb0b15efd build: add nconfig
Add support for make target nconfig (ncurses)

Reviewed-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Signed-off-by: Sergio E. Nemirowski <sergio@outerface.net>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-07-07 19:47:24 +02:00
Daniel Golle
3b0f698760 build,json: fix build failure in case no data is found
Only collect arch_packages if actually generating any output.

Fixes: commit f09b9319 ("build,json: store arch_packages in profiles.json"(
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Paul Spooren <mail@aparcar.org>
2020-07-03 22:09:24 +01:00
Paul Spooren
f09b9319c6 build,json: store arch_packages in profiles.json
The `arch_packages` contains the supported package architecture.

Previously it was necessary to parse the `Packages` index for the line
`Architecture:`, requiring both an additional parser and file download.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2020-07-03 15:28:05 +01:00
Paul Spooren
263f7e5bbd build: store default/device packages in JSON
With this commit the `profiles.json` contain both the target specific
`default_packages` as well as the device specific `device_packages` as a
array of strings.

This information is required for downstream projects like the various
web-based interactive firmware generators.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Paul Spooren <mail@aparcar.org>
2020-06-30 23:21:10 +01:00
Álvaro Fernández Rojas
3f8e163e01 scripts: config: remove accidentally added file
Also ignore the file.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-06-02 18:17:31 +02:00
Álvaro Fernández Rojas
35d7f92c60 scripts: support Sercomm load tags
Header consists in Sercomm PID bytes, followed by a SHA256 hash of the
input binary.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-06-02 13:06:42 +02:00
Álvaro Fernández Rojas
7f1250a7fe scripts: support Sercomm crypto
Sercomm firmwares are encrypted with AES 256 CBC.
The key is generated with a custom algorithm from the firmware tag:
	char key[32];
	char version[32];
	char iv[32];
	char random[32];
	char size[32];
Key must be generated with Sercomm's algorithm. However, the rest of the
header can be empty. IV and random are set to 0 on purpose.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-06-02 08:37:54 +02:00
Álvaro Fernández Rojas
58bdbe7321 scripts: support Sercomm partition tags
Sercomm uses a custom layout for partition tags:
	char part_name[32];
	char size[32];
	char part_version[32];
	char reserved[32];
	char rootfs_version[32];

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-06-02 08:33:11 +02:00
Rosen Penev
69f8983af4 scripts/flashing/flash.sh: remove trailing whitespaces
Signed-off-by: Rosen Penev <rosenp@gmail.com>
[cut out of patch with different subject]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-24 14:44:00 +02:00
Rosen Penev
34a2780395 scripts/flashing/flash.sh: Add missing quotes
These are in if statements (where they should be), and echo output that is
not piped to anything. These should be safe.

Found with shellcheck.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2020-05-24 14:44:00 +02:00
Álvaro Fernández Rojas
d90828411a scripts: add CFE Partition Tags support
Some BCM63xx NAND devices require a specific JFFS2 partition tag to verify
the JFFS2 partition validity:
	u32 part_id;
	u32 part_size;
	u16 flags;
	char part_name[33];
	char part_version[21];
	u32 part_crc32;

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-21 19:11:24 +02:00
Eneas U de Queiroz
80b350f528 build: have config-clean deal with old temp files
This is a temporary commit to have 'make config-clean' remove
temporary files from the previous scripts/config version.

The .gitignore file is updated to deal with the old files as well.

Cc: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
2020-05-20 17:03:45 +02:00
Eneas U de Queiroz
9f843b1d43 build: scripts/config - update to kconfig-v5.6
Major changes include:
 - Much more readable reverse dependencies separated in groups
 - Improved recursive dependency report
 - More readable .config files: add comments to signal end of menus
 - More warnings for incorrect Config.in entries, such as a 'choice'
   default not contained in the 'choice'
 - Hability to properly display pseudographics with non-latin locales
 - Recursive dependencies can optionally be treated as errors

Changes from failed dcf3e63a35 attempt:
 - Recursive dependencies are treated as warnings by default
 - The option to treat them as errors is implemented as a command-line
   flag to scripts/config/conf instead of a compile-time definition
 - fixed handling of select with umnet dependencies

Cc: Petr Štetiar <ynezz@true.cz>
Cc: Jo-Philip Wich <jow@mein.io>
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
2020-05-20 17:03:45 +02:00
Álvaro Fernández Rojas
258cb7f169 scripts: cfe-wfi-tag: fix shebang
Fixes: 72985233a6 ("scripts: support CFE WFI images")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-19 08:06:29 +02:00
Álvaro Fernández Rojas
30fcb62840 scripts: cfe-bin-header: fix shebang
Fixes: e575a7f777 ("scripts: support tags for CFE binaries")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-19 08:05:22 +02:00
Álvaro Fernández Rojas
72985233a6 scripts: support CFE WFI images
CFE WFI (Whole Flash Image) consists in 20 byte footer:
- u32: CRC32
- u32: WFI Version
- u32: Chip ID
- u32: Flash Type
- u32: Flags

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-18 18:24:06 +02:00
Álvaro Fernández Rojas
e575a7f777 scripts: support tags for CFE binaries
CFE loads binaries based on a 12 byte header which corresponds to:
- u32: Load Address
- u32: Entry Address
- u32: Size

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-18 18:24:06 +02:00
Paul Spooren
c737a9ee6a scripts/download: add sources CDN as first mirror
OpenWrt now has a CDN for sources at sources.cdn.openwrt.org which
mirrors sources.openwrt.org.

Downloading sources outside Europe or US (mainland) could
result in low throughput, extremely slowing down the first compilation of
the build system.

This patch adds sources.cdn.openwrt.org as the first mirror to offer
worldwide fast download speeds by default. If the CDN goes down for
whatever reason, the script jumps to the next available mirror and
downloads requested files as before (in regional varying speed).

Signed-off-by: Paul Spooren <mail@aparcar.org>
Acked-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
2020-04-14 23:16:55 +01:00
Paul Spooren
14cbd8fb2d scripts: JSON merge don't crash if no JSON found
The JSON `WORK_DIR` ($(KDIR)/json_info_files) is only created if the new
image generation methods from `image.mk` are used. However some targets
like `armvirt` do not use it yet, so the folder is never created.

The `json_overview_image_info.py` script used to raise an error if the
given `WORK_DIR` isn't a folder, however it should just notify about
missing JSON files.

This patch removes the Python assert and exists with code 0 even if no
JSON files were found, as this is not necessarily an error but simply
not yet implemented. Using `glob` on an not existing `Path` results in
an empty list, therefore the for loop won't run.

Signed-off-by: Paul Spooren <mail@aparcar.org>
CC: Petr Štetiar <ynezz@true.cz>
2020-04-14 23:16:55 +01:00
Jo-Philipp Wich
7b1d809a8d Revert "build: scripts/config - update to kconfig-v5.6"
This reverts commit dcf3e63a35.

The kconfig update requires further testing and refinement until it can
remain in tree. Main problems are:

 - Recursive deps are now fatal instead of a warning
 - Previously legal syntax now leads to hard failures
 - It fails all package builds since multiple days

The updated kconfig implementation needs to cope with the current status
quo in the various package feeds before we can reconsider it for master.

It is not desirable that single broken packages can hard-fail the entire
build pipeline.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2020-04-12 00:10:47 +02:00
Jo-Philipp Wich
6c16d64b2a Revert "build: add option to warn on recursive dependency"
This reverts commit 3204430e38.

Reverting this commit in preparation for reverting
dcf3e63a35 ("build: scripts/config - update to kconfig-v5.6") which
introduces various unaddressed build breakages.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2020-04-12 00:10:30 +02:00
Jo-Philipp Wich
fbc01f2a4c Revert "build: config: allow bool to select a module pkg"
This reverts commit 8514b6b42c.

Reverting this commit in preparation for reverting
dcf3e63a35 ("build: scripts/config - update to kconfig-v5.6") which
introduces various unaddressed build breakages.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2020-04-12 00:10:16 +02:00
Eneas U de Queiroz
8514b6b42c build: config: allow bool to select a module pkg
kconfig-v5.6 disallowed a bool symbol to select another symbol that
'depends on m' (i.e. can be only 'm' on 'n').  It is, in fact, an unmet
dependency to have set to 'y'.  However, openwrt depends on the previous
behavior, to be able to build a package that can be a module or built-in
depending on a bool config.  This restores the previous behavior.

Ref: https://forum.openwrt.org/t/wireless-fails-on-snapshot-r12900-kernel-5-4-on-c2600-ipq806x
Tested-by: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz> [added forum ref]
2020-04-11 19:06:26 +02:00
Eneas U de Queiroz
3204430e38 build: add option to warn on recursive dependency
This addes the option to treat recursive dependencies as warnings
instead of errors, by running make with WARN_RECURSIVE_DEP=1.

Note that the script/config targets will not get rebuilt when you add or
remove WARN_RECURSIVE_DEP while running make.  One must run
'make config-clean' before building config with a different setting.

Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
2020-04-09 12:51:10 +02:00
Eneas U de Queiroz
dcf3e63a35 build: scripts/config - update to kconfig-v5.6
Major changes include:
 - Much more readable reverse dependencies separated in groups
 - Improved recursive dependency report
 - More readable .config files: add comments to signal end of menus
 - More warnings for incorrect Config.in entries, such as a 'choice'
   default not contained in the 'choice'
 - Hability to properly display pseudographics with non-latin locales
 - Recursive dependencies are now treated as errors - this should make
   it harder for them to creep in.

Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
2020-04-09 12:51:10 +02:00
Eneas U de Queiroz
8636a17214 build: simplify building *config targets
Instead of passing pkg-config location through a variable when building
qconf (make xconfig), prepend its parent directory to the PATH, as it is
being done for other conf targets.

Use a Makefile pattern rule to group all 'scripts/config/%onf'
(currently conf, mconf, qconf) targets in a single rule.  Add -O2 to
CFLAGS when building them as well.

Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
2020-04-09 12:51:10 +02:00
Paul Spooren
07449f692c build: refactor JSON info files to profiles.json
JSON info files contain machine readable information of built profiles
and resulting images. These files were added in commit 881ed09ee6
("build: create JSON files containing image info").

They are useful for firmware wizards and script checking for
reproducibility.

Currently all JSON files are stored next to the built images, resulting
in up to 168 individual files for the ath79/generic target.

This patch refactors the JSON creation to store individual per image
(not per profile) files in $(BUILD_DIR)/json_info_files and create an
single overview file called `profiles.json` in the target directory.

Storing per image files and not per profile solves the problem of
parallel file writes. If a profiles sysupgrade and factory image are
finished at the same time both processes would write to the same JSON
file, resulting in randomly broken outputs.

Some target like x86/64 do not use the image code yet, resulting in
missing JSON files. If no JSON info files were created, no
`profiles.json` files is created as it would be empty anyway.

As before, this creation is enabled by default only if `BUILDBOT` is set.

Tested via buildroot & ImageBuilder on ath79/generic, imx6 and x86/64.

Signed-off-by: Paul Spooren <mail@aparcar.org>
[json_info_files dir handling in Make, if case refactoring]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-04-03 12:17:45 +02:00
李国
a6b7c3e672 x86: generate EFI platform bootable images
Add EFI platform bootable images for x86 platforms. These images can
also boot from legacy BIOS platform.

EFI System Partition need to be fat12/fat16/fat32 (not need to load
filesystem drivers), so the first partition of EFI images are not ext4
filesystem any more.

GPT partition table has an alternate partition table, we did not
generate it. This may cause problems when use these images as qemu disk
(kernel can not find rootfs), we pad enough sectors will be ok.

Signed-off-by: 李国 <uxgood.org@gmail.com>
[part_magic_* refactoring, removed genisoimage checks]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-03-31 16:20:47 +02:00
Paul Spooren
2cb6d471b7 scripts: fixup qemustart for new x86 image names
qemustart allows easy testing of created images via `qemu`. The script
automatically selects created images and can setup e.g. networks.

As the x86 target now uses the generic image.mk the profile appears also
in the image name, this is *generic*.

Add the profile name to the qemustart script so it still finds the file.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2020-03-21 10:36:00 +00:00
Jeffery To
f96cfe019a build: Fix directory symlinks not removed when cleaning STAGING_DIR
Currently, a symbolic link whose target is a directory will not be
removed when cleaning packages from STAGING_DIR.

In the first cleaning pass in scripts/clean-package.sh, the -f test for
a directory symlink returns false (because the link target is a
directory) and so the symlink is not removed.

In the second pass, the -d test returns true for a directory symlink,
but the symlink is not removed by rmdir because rmdir only removes
(real) directories.

This updates clean-package.sh to remove all non-directories (including
symbolic links) in the first pass.

Signed-off-by: Jeffery To <jeffery.to@gmail.com>
2020-03-01 21:35:59 +01:00
Rosen Penev
e37e2f0cf1 scripts/arm-magic.sh: switch to /bin/sh
This does not use any special bash stuff.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2020-01-02 23:59:20 +01:00
Rosen Penev
995378a2a5 scripts/env: replace -a and -o with &&/||
The former are not well defined.

Found with shellcheck.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2020-01-02 23:56:19 +01:00
Rosen Penev
2fe5319d58 scripts/env: use explicit find location
Some find binaries do not imply the current directory.

Found with shellcheck.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2020-01-02 23:51:45 +01:00
Rosen Penev
33f87d2ef6 scripts/gen-dependencies.sh: use /bin/sh
This uses no special bash stuff.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2020-01-01 17:01:02 +01:00
Rosen Penev
dec46a9ea0 scripts/gen-dependencies.sh: replace backticks with $()
Found with shellcheck.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2020-01-01 17:00:38 +01:00
Rosen Penev
9a8ba44f9c scripts/mkits.sh: replace legacy backticks with $()
This replaces deprecated backticks by more versatile $(...) syntax.

Found with shellcheck.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
[adjust commit title and message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-31 11:44:04 +01:00
Rosen Penev
543d945f07 scripts/symlink-tree.sh: use /bin/sh
This uses nothing bash specific.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2019-12-31 11:43:15 +01:00