Since KERNEL_SWAP is only enabled by default for !SMALL_FLASH targets, we need
to check if the current kernel supports swap before trying to configure
zram-swap, as opkg can't check for kernel dependencies.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
The FRITZ!Box 3390 actually contains two SoCs, one Lantiq with a
5GHz WiFi and one AR9342 with a 2.4GHz WiFi. Only the Lantiq
has access to the flash memory, the Atheros runs fully from RAM.
Specifications
--------------
- Lantiq 500 MHz
- 128MiB RAM
- 128MiB NAND
- 256k Flash
- AR9580 5GHz WiFi
- AR9342 560 MHz
- 64MiB RAM
- AR9328 2.4GHz WiFi
Remarks
-------
This commit only adds support for the Lantiq side of things and
prepares the drivers for communication with the Atheros SoC. Thus,
only 5GHz WiFi works by default, the 2.4GHz WiFi will be added via
another target.
Some kernel patches will be required to add support for the Atheros SoC.
Installation
------------
Use the eva_ramboot.py script to boot the initramfs image. Then, transfer
the sysupgrade image to the device and run sysupgrade to flash it to the
NAND.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
Acked-by: Aleksander Jan Bajkowski A.Bajkowski@stud.elka.pw.edu.pl
Signed-off-by: Joachim Cerny <cocktail_yogi@web.de>
Switch to Actual Net Data Rate (ACTNDR) for speed reporting on lantiq VDSL modems
Refer to ITU-T G.997.1 chapter 7.5.2.8
Independent whether retransmission is used or not in a given transmit direction:
- In L0 state, this parameter reports the Net Data Rate (as specified in G.992.3, G.992.5 or G.993.2) at which the bearer channel is operating.
- In L2 state, the parameter contains the Net Data Rate (as specified in G.992.3, G.992.5 or G.993.2) in the previous L0 state.
Signed-off-by: Jeroen Peelaerts <jeroen.peelaerts@gmail.com>
Reviewed-by: Andre Heider <a.heider@gmail.com>
This commit adds monitoring for a couple of DSL line features that are
present in the lantiq firmware blobs.
* G.INP ON/OFF
* Trellis encoding ON/OFF
* Virtaul Noise ON/OFF
* Bitswap ON/OFF
Difference in size for ltq-vdsl-app = 1k
Difference in size for kmod-ltq-vdsl-vr9 < 1k
Reviewed-by: Andre Heider <a.heider@gmail.com>
Signed-off-by: Jeroen Peelaerts <jeroen.peelaerts@gmail.com>
"firmware" partition size defined in the device tree file is 0xf70000,
so the right IMAGE_SIZE is 15808k
Fixes: df1e5d6463 ("ramips: fix partition layout of hiwifi hc5x61")
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Add 5.10 as testing kernel. Builds successfully with
CONFIG_ALL_KMODS=y enabled.
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
This was done by executing these commands:
$ make kernel_oldconfig CONFIG_TARGET=subtarget
$ make kernel_oldconfig CONFIG_TARGET=subtarget_platform
Some common symbols have been moved to target config.
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
This was done by executing these commands:
$ make kernel_oldconfig CONFIG_TARGET=subtarget
$ make kernel_oldconfig CONFIG_TARGET=subtarget_platform
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
If service() is called w/o parameter then the status display for services
with multiple instances is incorrect. E.g. samba4 or wpad have 2 instances.
root@OpenWrt:~# /etc/init.d/samba4 status
running
root@OpenWrt:~# /etc/init.d/wpad status
running
Before change:
/etc/init.d/samba4 enabled stopped
/etc/init.d/wpad enabled stopped
After change:
/etc/init.d/samba4 enabled running
/etc/init.d/wpad enabled running
Signed-off-by: Alexander Egorenkov <egorenar-dev@posteo.net>
Upstream iproute2 detects libbpf using a one-line $CC test-compile, which
normally ignores LDFLAGS. With NLS enabled however, LDFLAGS includes an
"rpath-link" linker option needed to resolve libintl.so. Its absence
causes both the compile and libbpf detection to fail:
ld: warning: libintl.so.8, needed by libbpf.so, not found (try using
-rpath or -rpath-link)
ld: libelf.so.1: undefined reference to `libintl_dgettext'
collect2: error: ld returned 1 exit status
Fix this by directly including $LDFLAGS in the test-compile command.
Reported-by: Ian Cooper <iancooper@hotmail.com>
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
The libbfd package definition uses $(ICONV_DEPENDS) and $(INTL_DEPENDS)
but links against neither, leading to libbfd detection failures in other
packages (e.g. bpftools) and on-target relocation problems with libintl.so:
root@OpenWrt:/# ldd /usr/lib/libbfd.so
ldd (0x77db6000)
libc.so => ldd (0x77db6000)
libgcc_s.so.1 => /lib/libgcc_s.so.1 (0x77c6d000)
Error relocating /usr/lib/libbfd.so: libintl_dgettext: symbol not found
Add NLS-conditional linking of "libintl" to fix this. Also remove libbfd
package dependency $(ICONV_DEPENDS) which is not used during building or
linking.
Tested with QEMU on malta/be32, after building all packages from binutils,
bpftools and iproute2, using different libc options musl and glibc.
Fixes: 08e8175696 ("binutils: use nls.mk to fix libbfd link errors in
other packages")
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
There is no direct linking of libintl from bpftools, only secondary linking
through libelf, so remove "-lintl" from TARGET_LDFLAGS.
Fixes: 5582fbd613 ("bpftools: support NLS, fix ppc build and update to 5.8.9")
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Ran update_kernel.sh in a fresh clone without any existing toolchains.
Manually rebased:
pending-5.4/611-netfilter_match_bypass_default_table.patch
The upstream change affecting this patch is the revert of an earlier
kernel commit. Therefore, we just revert our corresponding changes
in [1].
Build system: x86_64
Build-tested: ipq806x/R7800
[1] 9b1b89229f ("kernel: bump 5.4 to 5.4.86")
Signed-off-by: John Audia <graysky@archlinux.us>
[adjust manually rebased patch, add explanation]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
1. Add leds and configs
2. Add network configs
3. Add script to clear partial boot flag
4. Hack to use port 5 as cpu port as port 8 connected to eth2
wont pass any frames
5. Enable EA9500 image generation
Hardware Info:
- Processor - Broadcom BCM4709C0KFEBG dual-core @ 1.4 GHz
- Switch - BCM53012 in BCM4709C0KFEBG & external BCM53125
- DDR3 RAM - 256 MB
- Flash - 128 MB (Toshiba TC58BVG0S3HTA00)
- 2.4GHz - BCM4366 4×4 2.4/5G single chip 802.11ac SoC
- Power Amp - Skyworks SE2623L 2.4 GHz power amp (x4)
- 5GHz x 2 - BCM4366 4×4 2.4/5G single chip 802.11ac SoC
- Power Amp - PLX Technology PEX8603 3-lane, 3-port PCIe switch
- Ports - 8 Ports, 1 WAN Ports
- Antennas - 8 Antennas
- Serial Port - @j6 [GND,TX,RX] (VCC NC) 115200 8n1
Flashing Instructions:
1. Connect a USB-TTL table to J6 on the router as well as a
ethernet cable to a lan port and your PC.
2. Power-on the router.
3. Use putty or a serial port program to view the terminal.
Hit Ctrl+C and interrupt the CFE terminal terminal.
4. Setup a TFTP server on your local machine at setup you
local IP to 192.168.1.2
5. Start the TFTP Server
6. Run following commands at the CFE terminal
flash -noheader 192.168.1.2:/openwrt.trx nflash0.trx
flash -noheader 192.168.1.2:/openwrt.trx nflash0.trx2
nvram set bootpartition=0 && nvram set partialboots=0 && nvram commit
7. Reboot router to be presented by OpenWrt
Note: Only installation method via serial cable is supported at the moment.
The trx firmware has to be flashed to both the partitions using following
commands from CFE prompt. This will cover US and Non-US variants.
Signed-off-by: Vivek Unune <npcomplete13@gmail.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
973cc6c compiler: actually expand block scope fix to for/while alt syntax
97bf297 compiler: ensure that alternative if/for/while syntax has own block scope
f0e2a64 tests: add missing test case for fixed switch codegen
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The uImage.FIT partition parser used to squeeze in FIT partitions in
the range where partition editor tools (fdisk and such) expect the
regular partition. This is confusing people and tools when adding
additional partitions on top of the partition used for OpenWrt's
uImage.FIT.
Instead of squeezing in the additional partitions, rather start with
all uImage.FIT partitions at offset 64.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Introduce cmdline_get_var() to /lib/function.sh and make use of it in
export_rootdev() in /lib/upgrade/common.sh, making the code more
simple and removing one level of indentation.
Introduce get_partition_by_name() to /lib/upgrade/common.sh which is
useful on non-EFI GPT platforms like mt7622.
Remove some dead-code while at it.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Fixes the following error when building without CONFIG_MODULE_STRIPPED:
FATAL: modpost: sound/soc/ralink/snd-soc-ralink-i2s: struct
of_device_id is not terminated with a NULL entry!
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
MIPS Coherent Processor Systems (CPS), which include the MT7621 SoC, support
deep sleep idle states and have a specific cpuidle driver for them.
Enable support for it, while also switching from constant timer ticks to the
idle dynticks model, with the TEO governor.
Run-tested on a Redmi AC2100.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
We've been carrying this patch for many years [1], in order to fix a timer
calibration issue on MT7621. Turns out, after retesting with a recent kernel
(Linux 5.10), the system works perfectly fine without it (no rcu_sched stalls
or inconsistent BogoMIPS values across CPUs).
Manually refreshed:
322-mt7621-fix-cpu-clk-add-clkdev.patch
323-mt7621-memory-detect.patch
[1] https://git.openwrt.org/?p=openwrt/openwrt.git;a=commitdiff;h=6f4a903533361a2906a4d94ac6f597cd9c6c47bc
Suggested-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Tested-by: Donald Hoskins <grommish@gmail.com>
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
a4355a6 firewall3: clean up the flow table detection logic
edd0dc5 firewall3: create a common helper to find strings in files
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
The terminfo is required by the popular terminal multiplexer screen and
tmux, offer it by default as the size impact is minimal with 885 Bytes.
Signed-off-by: Paul Spooren <mail@aparcar.org>
The terminfo files were all in one row which is terrible to read.
Split them over multiple lines to improve readability.
Signed-off-by: Paul Spooren <mail@aparcar.org>
The Pine64(+) and the SoPine64 baseboard has two USB ports. One of
these (the lower) is connected directly to a USB host, the other
one's (upper) PHY is shared with the separate OTG controller. In
order to get it working, MUSB support needs to be enabled.
As there are other targets which compile MUSB support into the kernel
and not package it into modules, the same is done here.
[ 1.348760] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.04
[ 1.357029] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.364250] usb usb5: Product: MUSB HDRC host driver
[ 1.369219] usb usb5: Manufacturer: Linux 5.4.99 musb-hcd
[ 1.374617] usb usb5: SerialNumber: musb-hdrc.1.auto
[ 1.379891] hub 5-0:1.0: USB hub found
[ 1.383677] hub 5-0:1.0: 1 port detected
[...]
[ 697.299440] usb 1-1: new high-speed USB device number 2 using ehci-platform
[ 697.461855] usb 1-1: New USB device found, idVendor=090c, idProduct=1000, bcdDevice=11.00
[ 697.470038] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 697.477180] usb 1-1: Product: USB Flash Disk
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
1. Use upstream accepted NVMEM patches
2. Minor fix for BCM4908 partitioning
3. Support for Linksys firmware partitions on Northstar
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This includes several improvements and fixes:
61db17e rules: fix device and chain usage for DSCP/MARK targets
7b844f4 zone: avoid duplicates in devices list
c2c72c6 firewall3: remove last remaining sprintf()
12f6f14 iptables: fix serializing multiple weekdays
00f27ab firewall3: fix duplicate defaults section detection
e8f2d8f ipsets: allow blank/commented lines with loadfile
8c2f9fa fw3: zones: limit zone names to 11 bytes
78d52a2 options: fix parsing of boolean attributes
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
The original GL.iNet firmware has two different mac addresses in the
factory/art partition. The first one is for the WAN interface only and the
second one is for both lan0 and lan1.
But the original submission for OpenWrt didn't initialize the mac
addresses of the LAN ports for the DSA device at all. The ethernet mac
address was then used for all DSA ports.
Fixes: 050c24f05c ("mvebu: add support for GL.iNet GL-MV1000")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
There are only two lan ports and one wan port on Youku yk1
Fixes: e9baf8265b ("ramips: add support for Youku YK1")
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[add Fixes:]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
