Hardware:
- SoC: MediaTek MT7628AN (MIPS 580MHz)
- Flash: 16 MiB XMC 25QH128CH10
- RAM: 128 MiB ESMT M14D1G1664A
- WLAN: 2.4 GHz (MT7628), 5 GHz (MT7613BEN 802.11ac)
- Ethernet: 1x 10/100 Mbps WAN, 1x 10/100 LAN (MT7628)
- USB 2.0 port
- Buttons: 1 Reset button, 1 slider button
- LEDs: 1x Red, 1x White
- Serial console: unpopulated header, 115200 8n1
- Power: 5 VDC, 2 A
MAC addresses:
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| WAN | 80:af:ca:xx:xx:x0 | label |
| LAN | 80:af:ca:xx:xx:x0 | label |
| WLAN 2g | 80:af:ca:xx:xx:x0 | label |
| WLAN 5g | 80:af:ca:xx:xx:x2 | label+2 |
+---------+-------------------+-----------+
Installation:
The installation must be done via TFTP by disassembling the router.
On other occasions Cudy has distributed intermediate firmware to make
installation easier, and so I recommend checking the Wiki for this
device if there is a more convenient solution than the one below.
To install using TFTP:
1. Upgrade to a beta firmware (signed by Cudy) that can be downloaded
from the wiki. This is required in order to use an unlocked u-boot.
2. Connect to UART.
3. While the router is turning on, press 1.
4. Connect to LAN and set your IP to 192.168.1.88/24. Configure a TFTP
server and an OpenWrt initramfs-kernel.bin firmware file as recovery.bin.
5. Press Enter three times. Verify the filename.
6. If you can reach LuCI or SSH now, just use the sysupgrade image with
the 'Keep settings' option turned off.
If you don't want to use the beta firmware nor the unlocked u-boot, you
can install the firmware writing the sysupgrade image on the firmware
partition of the SPI flash.
Signed-off-by: Luis Mita <luis@luismita.com>
(cherry picked from commit f1091ef7ac)
Link: https://github.com/openwrt/openwrt/pull/15875
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In kernel 5.15, the default erase sector size of the nor flash has
been switched from 4k to 64k. This may cause the configuration not
be preserved across upgrades. To avoid this issue, change the default
BLOCKSIZE to 64k.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Add support for OrayBox X1. It is a 802.11n router, based on MediaTek MT7628N.
Specifications:
SoC: MediaTek MT7628N (580MHz)
RAM: 64 MiB
Flash: 16 MiB NOR (Winbond W25Q128JVSIQ)
Wireless: 802.11b/g/n 2x2 2.4GHz (Built In)
Ethernet: 1x 100Mbps only
USB: 1x USB Type-A 2.0 Host Port
Button: 1x "Reset" button
LED: 1x Blue LED + 1x Red LED + 1x White LED
Power: 5V Micro-USB input
Manufacturer Page:
https://pgy.oray.com/router/x1.html/parameter
Flash Layout:
0x000000000000-0x000000030000 : "u-boot"
0x000000030000-0x000000040000 : "kpanic"
0x000000040000-0x000000050000 : "factory"
0x000000050000-0x000000fe0000 : "firmware"
0x000000fe0000-0x000000ff0000 : "bdinfo"
0x000000ff0000-0x000001000000 : "reserve"
Install via SSH:
Original firmware is based on OpenWRT, but SSH is not start by default,
You should enable it first
1. Login into web admin (10.168.1.1), default password is 'admin'
2. Open the following link, and the result should be {"code":0};
SSH is now started, username is root, password is same as web admin password
http://10.168.1.1/cgi-bin/oraybox?_api=ssh_set&enabled=1
4. You can flash firmware via mtd: mtd write /tmp/firmware_image.bin firmware
Signed-off-by: Bin We <me@udp.pw>
- drop unneeded default-state for led_power
- concat firmware partitions to extend available free space
- increase spi flash frequency to 32 Mhz (value from stock firmware bootlog)
- drop broken-flash-reset because of onboard flash chip W25Q256FV has reset support
- add compatible for pcie wifi according to kernel documetation
- switch to wan mac address with offset 0x28 in rf-eeprom
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
This device is a 'Range extender' variant of the Xiaomi 4A router.
Its identical to the 100m non-intl/chinese version as much as it can run
the same firmware, differences being form factor, LEDs, WPS button
and one 100M port only.
The stock firmware differs significantly, being 'app managed only'.
Device specification
--------------------
SoC: MT7628DAN MIPS_24KEc@580MHz 2.4G-n 2x2
WiFi: MT7612EN 5G-ac 80MHz 2T2R
Flash: 16MB W25Q128BV
DRAM: 64MB built-in SoC
Switch: built-in SoC
Ethernet: 1x10/100 Mbps
USB: None
Antennas: 2 x external, non-detachable
LEDs: 2 programmable blue/amber
Buttons: WPS and reset (hidden)
Housing: Range Extender / Wall wart
Serial: 115200,8n1
MAC Addresses
-------------
All 3 MACs are read from flash and identical to stock.
Label MAC is WIFI 2G
Installation
------------
No HTML UI on this device, serial console only. The serial connector
is unpopulated but standard size and clearly marked. Flash from the
U-Boot shell at boot by choosing (2) and flashing the sysupgrade file
via tftp.
Recovery/Debricking procedures of the xiaomi 4A and variants should
work, but there currently is no official source for the stock firmware.
Signed-off-by: Jo Deisenhofer <jo.deisenhofer@gmail.com>
Keenetic KN-1613 is a 2.4/5 Ghz band 11ac (Wi-Fi 5) router, based on MT7628AN.
Specification:
- System-On-Chip: MT7628AN
- CPU/Speed: 580 MHz
- Flash-Chip: Winbond w25q256
- Flash size: 32768 KiB
- RAM: 128 MiB
- 4x 10/100 Mbps Ethernet
- 2x external, non-detachable antennas
- UART (J1) header on PCB (115200 8n1)
- Wireless No1 (2T2R): SoC Built-in 2.4 GHz 802.11bgn
- Wireless No2 (2T2R): MT7613BE 5 GHz 802.11ac
- 4x LED, 2x button, 1x mode switch
Notes:
- The device supports dual boot mode
- The firmware partitions were concatinated into one
- The FN button led indicator has been reassigned as the 2.4GHz
wifi indicator.
Flash instruction:
The only way to flash OpenWrt image is to use tftp recovery mode in U-Boot:
1. Configure PC with static IP 192.168.1.2/24 and tftp server.
2. Rename "openwrt-ramips-mt76x8-keenetic_kn-1613-squashfs-factory.bin"
to "KN-1613_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
the router and keep button pressed until power led start blinking.
4. Router will download file from server, write it to flash and reboot.
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
CPU: MediaTek MT7628AN @ 575 MHz
Flash: 16 MB
RAM: 128 MB
Ethernet: 10/100Mbps x 1
Wlan: 300 Mbps
USB: USB 2.0 x 1
LED: red/green x 1
Button: reset x 1
1. Open https://www.hiwifi.wtf/, Get Cloud token and unlock ssh
2. Upload the openwrt firmware to the router via SCP
3. Login the router via SSH
4. Run `mtd -r write path_to_firmware.bin firmware`
I have tested on my device.
- The LED will display RED on power-on, After system start completed, trun GREEN
- Reset button working now. Long press after 5s will reset factory. Short press less 1s will reboot the device
- USB can working under official u-boot
Signed-off-by: Senis John <thank243@gmail.com>
RT-N600 is internally the same as RT-AC1200, as veryfied by @russinnes .
Adding alt_name so that people can find it in firmware selector.
Signed-off-by: Ray Wang <raywang777@foxmail.com>
Tested-by: Russ Innes <russ.innes@gmail.com>
Aka Kroks Rt-Cse5 UW DRSIM (KNdRt31R16), ID 1958:
https://kroks.ru/search/?text=1958
See Kroks OpenWrt fork for support of other models:
https://github.com/kroks-free/openwrt
Device specs:
- CPU: MediaTek MT7628AN
- Flash: 16MB SPI NOR
- RAM: 64MB
- Bootloader: U-Boot
- Ethernet: 5x 10/100 Mbps
- 2.4 GHz: b/g/n SoC
- USB: 1x
- SIM-reader: 2x (driven by a dedicated chip with it's own firmware)
- Buttons: reset
- LEDs: 1x Power, 1x Wi-Fi, 12x others (SIM status, Internet, etc.)
Flashing:
- sysupgrade image via stock firmware WEB interface, IP: 192.168.1.254
- U-Boot launches a WEB server if Reset button is held during power up,
IP: 192.168.1.1
MAC addresses as verified by OEM firmware:
vendor OpenWrt source
LAN eth0 factory 0x4 (label)
2g wlan0 label
Signed-off-by: Andrey Butirsky <butirsky@gmail.com>
Aka "Kroks KNdRt31R19".
Ported from v19.07.8 of OpenWrt fork:
see https://github.com/kroks-free/openwrt
for support of other models.
Device specs:
- CPU: MediaTek MT7628AN
- Flash: 16MB SPI NOR
- RAM: 64MB
- Bootloader: U-Boot
- Ethernet: 1x 10/100 Mbps
- 2.4 GHz: b/g/n SoC
- mPCIe: 1x (usually equipped with an LTE modem by vendor)
- Buttons: reset
- LEDs: 1x Modem, 1x Injector, 1x Wi-Fi, 1x Status
Flashing:
- sysupgrade image via stock firmware WEB interface.
- U-Boot launches a WEB server if Reset button is held during power up.
Server IP: 192.168.1.1
SIM card switching:
The device supports up to 4 SIM cards - 2 locally on board and 2 on
remote SIM-injector.
By default, 1-st local SIM is active.
To switch to e.g. 1-st remote SIM:
echo 0 > /sys/class/gpio/modem1power/value
echo 0 > /sys/class/gpio/modem1sim1/value
echo 1 > /sys/class/gpio/modem1rsim1/value
echo 1 > /sys/class/gpio/modem1power/value
MAC addresses as verified by OEM firmware:
vendor OpenWrt source
LAN eth0 factory 0x4 (label)
2g wlan0 label
Signed-off-by: Kroks <dev@kroks.ru>
[butirsky@gmail.com: port to master; drop dts-v1]
Signed-off-by: Andrey Butirsky <butirsky@gmail.com>
The international version of Mi Router 4A 100M is physically
identical to the non-international one, but appears to be
using a different partitioning scheme with the "overlay"
partition being 2MiB in size instead of 1MiB. This means
the following "firmware" partition starts at a different
address and the DTS needs to be adjusted for the firmware
to work.
Signed-off-by: Nita Vesa <werecatf@outlook.com>
Specifications:
Chipset:MT7628DA+MT7612E
Antenna : 2.4Ghz:2x5dbi Antenna + 5.8Ghz:2x5dbi Antenna
Wireless Rate:2.4Ghz 300Mbps , 5.8Ghz 867Mbps
Output Power :100mW(20dbm)
Physical port:110/100Mbps RJ45 WAN Port , 310/100Mbps RJ45 LAN Port
Flash: 8Mb
DRam: 64Mb
Flashing: default bootloader attempts to boot from tftp://192.168.1.10/firmware_auto.bin using 192.168.1.1
Known issues:
mac-address-increment for 5GHZ doesnt work, i failed to figure out why. Original firmware using +1 from original value in factory partition.
Signed-off-by: Sergei Iudin <tsipa740@gmail.com>
Asus RT-N12+ B1 and Asus RT-N300 B1 are the same device
with a different name.
The OEM firmwares have the same MD5 with Asus RT-N11P B1.
Same instructions for Asus RT-N11P B1 see:
commit c3dc52e39a ("ramips: add support for Asus RT-N10P V3 / RT-N11P B1 / RT-N12 VP B1")
Signed-off-by: Semih Baskan <strstgs@gmail.com>
(Added id from the PR review to commit message)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Hardware specifications:
SoC: MT7628DAN MIPS_24KEc@580MHz 2.4G-n 2x2
WiFi: MT7613BEN 5G-ac 160MHz 2x2
Switch: 4x100M built-in SoC
Flash: 16MB W25Q128JVSQ SPI-NOR
DRAM: 64MB built-in SoC
MAC addresses as verified by OEM firmware:
use address source
Lan/Wan/2G *:60 factory 0x4 (label)
5G *:64 factory 0x8000
Serial console: 57600,8n1
Installation:
Asus windows recovery tool:
install the Asus firmware restoration utility
unplug the router, hold the reset button while powering it on
release when the power LED flashes slowly
specify a static IP on your computer:
IP address: 192.168.1.75
Subnet mask 255.255.255.0
start the Asus firmware restoration utility, specify the factory image
and press upload
do NOT power off the device after OpenWrt has booted until the LED flashing
after flashing OpenWrt, there will be first no 5GHz Wifi available probably,
wait until blinking finishes and do a reboot
TFTP Recovery method:
set computer to a static ip, 192.168.1.75
connect computer to the LAN 1 port of the router
hold the reset button while powering on the router for a few seconds
send firmware image using a tftp client; i.e from linux:
$ tftp
tftp> binary
tftp> connect 192.168.1.1
tftp> put factory.bin
tftp> quit
do NOT power off the device after OpenWrt has booted until the LED flashing
after flashing OpenWrt, there will be first no 5GHz Wifi available probably,
wait until blinking finishes and do a reboot
Signed-off-by: Tamas Balogh <tamasbalogh@hotmail.com>
The Wavlink WL-WN531A3 is an AC1200 router with 5 fast ethernet ports
and one USB 2.0 port.
It's also known as Wavlink QUANTUM D4.
Hardware
--------
SoC: Mediatek MT7628AN
RAM: 64MB
FLASH: 8MB NOR (GigaDevice GD25Q64CSIG3)
ETH:
- 5x 10/100 Mbps Ethernet (4x LAN + 1x WAN)
WIFI:
- 2.4GHz: 1x (integrated in SOC) (2x2:2)
- 5GHz: 1x MT7612E (2x2:2)
- 4 external antennas
BTN:
- 1x Reset button
- 1x WPS button
- 1x Turbo button
- 1x Touchlink button
- 1x ON/OFF switch
LEDS:
- 1x Red led (system status)
- 1x Blue led (system status)
- 7x Blue leds (wifi led + 5 ethernet ports + power)
USB:
- 1x USB 2.0 port
UART:
- 57600-8-N-1
J1
O VCC +3,3V (near lan ports)
o RX
o TX
o GND
Everything works correctly.
Currently there is no firmware update available. Because of this, in
order to restore the OEM firmware, you must firstly dump the OEM
firmware from your router before you flash the OpenWrt image.
Backup the OEM Firmware
-----------------------
The following steps are to be intended for users having little to none
experience in linux. Obviously there are many ways to backup the OEM
firmware, but probably this is the easiest way for this router.
Procedure tested on M31A3.V4300.200420 firmware version.
1) Go to http://192.168.10.1/webcmd.shtml
2) Type the following line in the "Command" input box and then press enter:
mkdir /etc_ro/lighttpd/www/dev; cp /dev/mtd0ro /etc_ro/lighttpd/www/dev/mtd0ro; ls -la /etc_ro/lighttpd/www/dev/mtd0ro
3) After few seconds in the textarea should appear this output:
-rw-r--r-- 1 0 0 8388608 /etc_ro/lighttpd/www/dev/mtd0ro
If your output doesn't match mine, stop reading and ask for
help in the forum.
4) Open in another tab http://192.168.10.1/dev/mtd0ro to download the
content of the whole NOR. If the file size is 0 byte, stop reading
and ask for help in the forum.
5) Come back to the http://192.168.10.1/webcmd.shtml webpage and type:
rm /etc_ro/lighttpd/www/dev/mtd0ro; for i in 1 2 3 4 ; do cp /dev/mtd${i}ro /etc_ro/lighttpd/www/dev/mtd${i}ro; done; ls -la /etc_ro/lighttpd/www/dev/
6) After few seconds, in the textarea should appear this output:
-rw-r--r-- 1 0 0 196608 mtd1ro
-rw-r--r-- 1 0 0 65536 mtd2ro
-rw-r--r-- 1 0 0 65536 mtd3ro
-rw-r--r-- 1 0 0 8060928 mtd4ro
drwxr-xr-x 7 0 0 0 ..
drwxr-xr-x 2 0 0 0 .
If your output doesn't match mine, stop reading and ask for
help in the forum.
7) Open the following links to download the partitions of the OEM FW:
http://192.168.10.1/dev/mtd1rohttp://192.168.10.1/dev/mtd2rohttp://192.168.10.1/dev/mtd3rohttp://192.168.10.1/dev/mtd4ro
If one (or more) of these files are 0 byte, stop reading and ask
for help in the forum.
8) Store these downloaded files in a safe place.
9) Reboot your router to remove any temporary file in ram.
Installation
------------
Flash the initramfs image in the OEM firmware interface
(http://192.168.10.1/update.shtml).
When Openwrt boots, flash the sysupgrade image otherwise you won't be
able to keep configuration between reboots.
Restore OEM Firmware
--------------------
Flash the "mtd4ro" file you previously backed-up directly from LUCI.
Warning: Remember to not keep settings!
Warning2: Remember to force the flash.
Notes
-----
1) Router mac addresses:
LAN XX:XX:XX:XX:XX:9B (factory @ 0x28)
WAN XX:XX:XX:XX:XX:9C (factory @ 0x2e)
WIFI 2G XX:XX:XX:XX:XX:9D (factory @ 0x04)
WIFI 5G XX:XX:XX:XX:XX:9E (factory @ 0x8004)
LABEL XX:XX:XX:XX:XX:9D
2) There is just one wifi led for both wifi interfaces.
It currently shows only the 2.4 GHz wifi activity.
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
Asus RT-AC1200 is a 2.4/5GHz dual band AC router,
based on MediaTek MT7628AN.
Specification:
* SoC: MT7628AN
* RAM: DDR2 64 MiB
* Flash: 16 MiB NOR (W25Q128BV)
* Wi-Fi:
* 2.4GHz: SoC Built-in
* 5GHz: MT7612EN
* Ethernet: 5x 100Mbps
* Switch: SoC built-in
* USB: 1x 2.0
Flash Layout:
0x0000000-0x0030000 : "bootloader"
0x0030000-0x0040000 : "nvram"
0x0040000-0x0050000 : "factory"
0x0050000-0x1000000 : "firmware"
MAC address:
LAN: factory 0x28
WAN: factory 0x22
2.4G: factory 0x4
5G: factory 0x8004
Installation via **recovery** mode:
1. Download the Asus recovery firmware (windows) tool from
http://dlcdnet.asus.com/pub/ASUS/LiveUpdate/Release/Wireless/Rescue.zip
2. Set your ethernet IP manually 192.168.1.5 / 255.255.255.0 with NO
gateway.
3. Plug in your ethernet to LAN port 1 on the router.
4. Load up the recovery software with the firmware file, but don't press
"Upload" yet.
5. Plug in the router to power WHILE HOLDING the reset button in. While
CONTINUING to hold the button, select "Upload" Continue to hold the
reset button in until it finishes and verifies!
6. If that doesn't work try pressing "Upload" first just before you do
step 5. At some point while holding reset the rescue tool will finally
detect and upload the firmware. That's when you can let go of the
reset button.
7. The router will reboot and not much will happen. Wait a minute or 2.
8. Power off and on the router again. Voila. Set everything your Ethernet
IP back to DHCP (automatically) and you're good to go.
Revert to stock firmware:
1. Install stock image via recovery mode.
Tested-by: Ivan Pavlov <AuthorReflex@gmail.com>
Signed-off-by: Ray Wang <raywang777@foxmail.com>
When Joowin WR758AC V1 and V2 devices were added, they should have been
added with the primary manufacturer name which is COMFAST, since Joowin
is just an alternate vendor name on some coutries or stores.
Fix this by changing the the vendor name on the respective files and set
Joowin as ALT0 variants while ensuring compatibility for early users.
Also adjust the model names to better follow the naming rules.
As a side effect, fix mt76x8 network script which was left incorrectly
unsorted on the case block conditions.
Fixes: 766733e172 ("ramips: add support for Joowin WR758AC V1 and V2")
Signed-off-by: Rodrigo Araujo <araujo.rm@gmail.com>
This commit adds support for Joowin (aka Comfast) WR758AC V1 and V2
devices.
Both have the same wall AP/repeater form factor and differ only
in the 5Ghz chipset (V1 has MT7662, V2 has MT7663).
OpenWrt developers forum page:
https://forum.openwrt.org/t/87355
Specifications:
- CPU: MediaTek MT7628AN (580MHz)
- Flash: 8MB
- RAM: 64MB DDR2
- 2.4 GHz: 802.11b/g/n (MT7603)
- 5 GHz: 802.11ac (V1 has MT7662, V2 has MT7663)
- Antennas: 4x external single band antennas
- LAN: 1x 10/100M
- LED: Wifi 3x blue. Programmable
- Button: WPS
MAC addresses as verified by OEM firmware:
use address source
LAN *:83 factory 0xe000
2g *:85 factory 0x4
5g *:86 factory 0x8004
How to install:
1- Setup a TFTP server on a machine with IP address 192.168.1.10/24
2- Name the image as `firmware_auto.bin` and place it on the root of the
TFTP server
3- Connect the device via Ethernet, it should pick and flash the image
Signed-off-by: Rodrigo Araujo <araujo.rm@gmail.com>
This commit adds support for the Wavlink WL-WN576A2 wall-plug wireles
repeater / router. It is also sold under the name SilverCrest SWV 733 B1.
Device specs:
- CPU: MediaTek MT7628AN
- Flash: 8MB
- RAM: 64MB
- Bootloader: U-Boot
- Ethernet: 1x 10/100 Mbps
- 2.4 GHz: b/g/n SoC
- 5 GHz: a/n/ac MT7610EN
- Buttons: WPS, reset, sliding switch (ap/repeater)
- LEDs: 5x wifi status, 1x LAN/WAN, 1x WPS
Flashing:
U-Boot launches a TFTP client if WPS button is held during boot.
- Server IP: 192.168.10.100
- Firmware file name: firmware.bin
Device will reboot automatically. First boot takes about 90s.
Coelner (waenger@gmail.com) is the original author, but I have made some
fixes. He does not wish to sign off using his real name.
Signed-off-by: Thomas Aldrian <dev.aldrian@gmail.com>
This commit adds support for Xiaomi MiWiFi 3C device.
Xiaomi MiWifi 3C has almost the same system architecture
as the Xiaomi Mi WiFi Nano, which is already officially
supported by OpenWrt.
The differences are:
- Numbers of antennas (4 instead of 2). The antenna management
is done via the µC. There is no configuration needed in the
software code.
- LAN port assignments are different. LAN1 and WAN are
interchanged.
OpenWrt Wiki: https://openwrt.org/toh/xiaomi/mir3c
OpenWrt developers forum page:
https://forum.openwrt.org/t/support-for-xiaomi-mi-3c
Specifications:
- CPU: MediaTek MT7628AN (575MHz)
- Flash: 16MB
- RAM: 64MB DDR2
- 2.4 GHz: IEEE 802.11b/g/n with Integrated LNA and PA
- Antennas: 4x external single band antennas
- WAN: 1x 10/100M
- LAN: 2x 10/100M
- LED: 1x amber/blue/red. Programmable
- Button: Reset
MAC addresses as verified by OEM firmware:
use address source
LAN *:92 factory 0x28
WAN *:92 factory 0x28
2g *:93 factory 0x4
OEM firmware uses VLAN's to create the network interface for WAN and LAN.
Bootloader info:
The stock bootloader uses a "Dual ROM Partition System".
OS1 is a deep copy of OS2.
The bootloader start OS2 by default.
To force start OS1 it is needed to set "flag_try_sys2_failed=1".
How to install:
1- Use OpenWRTInvasion to gain telnet, ssh and ftp access.
https://github.com/acecilia/OpenWRTInvasion
(IP: 192.168.31.1 - Username: root - Password: root)
2- Connect to router using telnet or ssh.
3- Backup all partitions. Use command "dd if=/dev/mtd0 of=/tmp/mtd0".
Copy /tmp/mtd0 to computer using ftp.
4- Copy openwrt-ramips-mt76x8-xiaomi_miwifi-3c-squashfs-sysupgrade.bin
to /tmp in router using ftp.
5- Enable UART access and change start image for OS1.
```
nvram set uart_en=1
nvram set flag_last_success=1
nvram set boot_wait=on
nvram set flag_try_sys2_failed=1
nvram commit
```
6- Installing Openwrt on OS1 and free OS2.
```
mtd erase OS1
mtd erase OS2
mtd -r write /tmp/openwrt-ramips-mt76x8-xiaomi_miwifi-3c-squashfs-sysupgrade.bin OS1
```
Limitations: For the first install the image size needs to be less
than 7733248 bits.
Thanks for all community and especially for this device:
minax007, earth08, S.Farid
Signed-off-by: Eduardo Santos <edu.2000.kill@gmail.com>
[wrap lines, remove whitespace errors, add mediatek,mtd-eeprom to
&wmac, convert to nvmem]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Specs (same as in v1):
- MT7628AN (575 MHz)
- 64MB RAM
- 8MB of flash (SPI NOR)
- 1x 10/100Mbps Ethernet (MT7628AN built-in switch with vlan)
- 1x 2.4GHz wifi (MT7628AN)
- 1x 5Ghz wifi (MT7612E)
- 4x LEDs (5 GPIO-controlled)
- 1x reset button
- 1x WPS button
The only and important difference between v1 & v3 is in flash memory
layout, so pls don't interchange these 2 builds!
Installation through web-ui (on OEM factory firmware):
1. Visit http://tplinkrepeater.net or the configured IP address of
your RE305 v3 (default 192.168.0.254).
2. Log in with the password you've set during initial setup of the
RE305 (there is no default password).
3. Go to Settings -> System Tools -> Firmware upgrade
4. Click Browse and select the OpenWRT image with factory.bin suffix
(not sysupgrade.bin)
5. A window with a progress bar will appear. Wait until it completes.
6. The RE305 will reboot into OpenWRT and serve DHCP requests on the
ethernet port.
7. Connect an RJ45 cable from the RE305 to your computer and access
LuCI at http://192.168.1.1/ to configure (or use ssh).
Disassembly:
Just unscrew 4 screws in the corners & take off the back cover.
Serial is exposed to the right side of the main board (in the middle)
and marked with TX/RX/3V3/GND, but the holes are filled with solder.
Installation through serial:
1. connect trough serial (1n8, baudrate=57600)
2. setup the TFTP server and connect it via ethernet
(ipaddr=192.168.0.254 of device, serverip=192.168.0.184 - your pc)
3. boot from a initramfs image first (choose 1 in the bootloader
options)
4. test it a bit with that, then proceed to run sysupgrade build
MAC addresses as verified by OEM firmware:
use OpenWrt address reference
LAN eth0 *:d2 label
2g wlan0 *:d1 label - 1
5g wlan1 *:d0 label - 2
The label MAC address can be found in config 0x2008.
Signed-off-by: Michal Kozuch <servitkar@gmail.com>
[redistribute WLAN node properties between DTS/DTSI, remove
compatible on DTSI, fix indent/wrapping, split out firmware-utils
change]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch adds support for D-Link DAP-1325-A1 (Range Extender Wi-Fi N300)
Specifications:
- SoC: 580Mhz MT7628NN
- RAM: 64MB, DDR2 SDRAM
- Storage: 8MB, SPI (W25Q64JVSSIQ)
- Ethernet: 1x 10/100 LAN port
- WIFI: 2.4 GHz 802.11bgn
- LED: Status (2x to provide 3 colors), Wi-Fi Signal Strength (4x)
- Buttons: Reset, WPS
- UART: Serial console (57600, 8n1)
Row of 4 holes near LAN port, starting from square hole:
3.3V, TX,RX,GND
- FCC ID: fccid.io/KA2AP1325A1/
Installation:
Failsafe UI
Firmware can be uploaded with Failsafe UI web page:
- turn device off
- press and hold reset button
- turn device on
- keep holding reset until red wifi strength led turns on (ab. 10sec)
- connect to device through LAN port
PC must be configured with static ip (192.168.0.x)
- connect to 192.168.0.50
- select image to be flashed and upload.
Device will reboot after successful update
Serial port/TFTP server
- Connect through serial connectors on PCB (e.g. with teraterm)
- Set up a TFTP server, and connect through LAN with static IP
- Put image file in the root of the server
- Boot the device and select '2' at U-Boot startup
- Set device IP, server IP and image file name
- Start upload and flash
Signed-off-by: Giovanni Cascione <ing.cascione@gmail.com>
[fix whitespaces in DTS, convert to nvmem, add mtd-eeprom]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Specifications:
* SOC: MT7628AN + MT7612E
* ROM: 8 MiB Flash
* RAM: 64 MiB DDR2
* WAN: 10/100M *1
* LAN: 10/100M *3
* Button: Reset *1
* LEDs: orange *1, white *1
* Antennas: 2.4 GHz *2 + 5 GHz *2
* TTL Baudrate: 57600
* TFTP Upgrade: IP: 192.168.51.1, Server: 192.168.51.100
MAC addresses as verified by OEM firmware:
use address source
2g *:d8 factory 0x0004 (label)
5g *:d9 factory 0x8004
LAN *:d7 factory $label -1
WAN *:da factory $label +2
Installation (TFTP + U-Boot):
* Connect device with a TTL cable and open a serial session by
PuTTY.
* Press "2" when booting to select "Load system code then write
to Flash via TFTP".
* Configure the IP of local host server.
* Upload firmware by tftpd64, it will boot when write instruction
is executed.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[fix DTS line endings, fix label MAC address, adjust status LED
names, convert mtd-mac-address-increment to mac-address-increment]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The minew g1-c is a smart home gateway / BLE gateway.
A Nordic nRF52832 is available via USB UART (cp210x) to support BLE.
The LED ring is a ring of 24x ws2812b connect to a generic GPIO (unsupported).
There is a small LED which is only visible when the device is open which
will be used as LED until the ws2812b is supported.
The board has also a micro sdcard/tfcard slot (untested).
The Nordic nRF52832 exposes SWD over a 5pin header (GND, VCC, SWD, SWC, RST).
The vendor uses an older OpenWrt version, sysupgrade can be used via
serial or ssh.
CPU: MT7628AN / 580MHz
RAM: DDR2 128 MiB RAM
Flash: SPI NOR 16 MiB W25Q128
Ethernet: 1x 100 mbit (Port 0) (PoE in)
USB: USB hub, 2x external, 1x internal to USB UART
Power: via micro usb or PoE 802.11af
UART: 3.3V, 115200 8n1
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
This commit adds support for the Wavlink WL-WN578A2 dual-band wall-plug
wireless router. This device is also sold under the name SilverCrest
SWV 733 A2.
Device Specifications:
- CPU: MediaTek MT7628AN (580MHz)
- Flash: 8MB
- RAM: 64MB
- Bootloader: U-Boot
- Ethernet: 2x 10/100 Mbps
- 2.4 GHz: 802.11b/g/n SoC
- 5 GHz: 802.11a/n/ac MT7610E
- Antennas: internal
- 4 green LEDs: WPS/Power, LAN, WAN, wifi-low, wifi-med, wifi-high
- Buttons: Reset, WPS
- Sliding mode switch: AP, repeater, client
- Small sliding power switch
Flashing instructions:
U-Boot launches TFTP client if WPS button is pressed during power-on.
Configure as follows:
- Server IP: 192.168.10.100
- Filename (rename sysupgrade file to this): firmware.bin
Flashing should not take more than a minute, device will reboot
automatically.
Signed-off-by: Thomas Aldrian <dev.aldrian@gmail.com>
Vendor firmware expects model name without manufacturer name inside
'supported_devices' part of metadata. This allows direct upgrade to
OpenWrt from vendor's GUI.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Make packages depending on usb-serial selective, so we do not have
to add kmod-usb-serial manually for every device.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Specifications:
- SoC: MediaTek MT7688AN
- RAM: 128 MB
- Flash: 32 MB
- Ethernet: 5x 10/100 (1x WAN, 4x LAN)
- Wireless: built in 2.4GHz (bgn)
- USB: 1x USB 2.0 port
- Buttons: 1x Reset
- LEDs: 1x (WiFi)
Flash instructions:
- Configure TFTP server with IP address 10.10.10.3
- Name the firmware file as firmware.bin
- Connect any Ethernet port to the TFTP server's LAN
- Choose option 2 in U-Boot
- Alternatively choose option 7 to upload firmware to the built-in
web server
MAC addresses as verified by OEM firmware:
use address source
2g *:XX factory 0x4
LAN *:XX+1 factory 0x28
WAN *:XX+1 factory 0x2e
Notes:
This board is ostensibly a module containing the MediaTek MT7688AN SoC,
128 MB DDR2 SDRAM and 32 MB flash storage. The SoC can be operated in
IoT Gateway Mode or IoT Device Mode.
From some vendors the U-Boot that comes installed operates on UART 2
which is inaccessible in gateway mode and operates unreliably in the
Linux kernel when using more than 64 MB of RAM. For those, updating
U-Boot is recommended.
Signed-off-by: Ewan Parker <ewan@ewan.cc>
[add WLAN to 01_leds]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This aligns the device/image names of the older Xiaomi Mi Router
devices with their "friendly" model and DEVICE_MODEL properties.
This also reintroduces consistency with the newer devices already
following that scheme.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This commit adds support for Xiaomi's Mi Router 4C device.
Specifications:
- CPU: MediaTek MT7628AN (580MHz)
- Flash: 16MB
- RAM: 64MB DDR2
- 2.4 GHz: IEEE 802.11b/g/n with Integrated LNA and PA
- Antennas: 4x external single band antennas
- WAN: 1x 10/100M
- LAN: 2x 10/100M
- LEDs: 2x yellow/blue. Programmable (labelled as power on case)
- Non-programmable (shows WAN activity)
- Button: Reset
How to install:
1- Use OpenWRTInvasion to gain telnet and ftp access.
2- Push openwrt firmware to /tmp/ using ftp.
3- Connect to router using telnet. (IP: 192.168.31.1 -
Username: root - No password)
4- Use command "mtd -r write /tmp/firmware.bin OS1" to flash into
the router..
5- It takes around 2 minutes. After that router will restart itself
to OpenWrt.
Signed-off-by: Ataberk Özen <ataberkozen123@gmail.com>
[wrap commit message, bump PKG_RELEASE for uboot-envtools, remove
dts-v1 from DTS, fix LED labels]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
TL-MR6400v5 is very similar to TL-MR6400v4. Main differences are:
- smaller form factor
- different LED GPIOs
- different switch connections
You can flash via tftp recovery:
- serve tftp-recovery image as /tp_recovery.bin on 192.168.0.225/24
- connect to any ethernet port
- power on the device while holding the reset button
- wait at least 8 seconds before releasing reset button
Flashing via OEM web interface does not work.
LTE module does not support DHCP so it must be configured via QMI.
Hardware Specification (v5.0 EU):
- SoC: MT7628NN
- Flash: Winbond W25Q64JVS (8MiB)
- RAM: ESMT M14D5121632A (64MiB)
- Wireless: SoC platform only (2.4GHz b/g/n, 2x internal antenna)
- Ethernet: 1NIC (4x100M)
- WWAN: TP-LINK LTE MODULE (2x external detachable antenna)
- Power: DC 9V 0.85A
Signed-off-by: Filip Moc <lede@moc6.cz>
You can flash via tftp recovery:
- serve tftp-recovery image as /tp_recovery.bin on 192.168.0.225/24
- connect to any ethernet port
- power on the device while holding the reset button
- wait at least 8 seconds before releasing reset button
Flashing via OEM web interface does not work.
LTE module does not support DHCP so it must be configured via QMI.
Hardware Specification (v4.0 EU):
- SoC: MT7628NN
- Flash: Winbond W25Q64JVS (8MiB)
- RAM: ESMT M14D5121632A (64MiB)
- Wireless: SoC platform only (2.4GHz b/g/n, 2x internal antenna)
- Ethernet: 1NIC (4x100M)
- WWAN: TP-LINK LTE MODULE (2x external detachable antenna)
- Power: DC 9V 0.85A
Signed-off-by: Filip Moc <lede@moc6.cz>
This patch adds support for the WiFi Pineapple Mark 7, a wireless
penetration testing tool.
Specifications:
* SoC: MediaTek MT7628 (580MHz)
* RAM: 256MiB (DDR2)
* Storage 1: 32MiB NOR (SPI)
* Storage 2: 2GB eMMC
* Wireless 1: 802.11b/g/n 2.4GHz (Built In)
* Wireless 2: 802.11b/g/n 2.4GHz (MT7601)
* Wireless 3: 802.11b/g/n 2.4GHz (MT7601)
* USB: 1x USB Type-A 2.0 Host Port
* Ethernet: 1x USB Type-C AX88772C Ethernet
* UART: 57600 8N1 on PCB
* Inputs: 1x Reset Button
* Outputs: 1x RGB LED
* FCCID: 2AA52MK7
Flash Instructions:
Original firmware is based on OpenWRT.
Use sysupgrade via SSH to flash.
Signed-off-by: Marc Egerton <foxtrot@realloc.me>
[pepe2k@gmail.com: set only required/used gpio groups to gpio function]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
TP-Link RE200 v4 is a wireless range extender with Ethernet and 2.4G and 5G
WiFi with internal antennas.
It's based on MediaTek MT7628AN+MT7610EN like the v2/v3.
Specifications
--------------
- MediaTek MT7628AN (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 1T1R 5 GHz
- 1x 10/100 Mbps Ethernet
- 8x LED (GPIO-controlled), 2x button
- UART connection holes on PCB (57600 8n1)
There are 2.4G and 5G LEDs in red and green which are controlled
separately.
MAC addresses
-------------
The MAC address assignment matches stock firmware, i.e.:
LAN : *:8E
2.4G: *:8D
5G : *:8C
MAC address assignment has been done according to the RE200 v2.
The label MAC address matches the OpenWrt ethernet address.
Installation
------------
Web Interface
-------------
It is possible to upgrade to OpenWrt via the web interface. Simply flash
the -factory.bin from OEM. In contrast to a stock firmware, this will not
overwrite U-Boot.
Recovery
--------
Unfortunately, this devices does not offer a recovery mode or a tftp
installation method. If the web interface upgrade fails, you have to open
your device and attach serial console.
Instructions for serial console and recovery may be checked out in
commit 6d6f36ae78 ("ramips: add support for TP-Link RE200 v2") or on
the device's Wiki page.
Signed-off-by: Richard Fröhning <misanthropos@gmx.de>
[removed empty line, fix commit message formatting]
Signed-off-by: David Bauer <mail@david-bauer.net>
This patch adds support for the TP-Link TL-WR850N v2. This device
is very similar to TP-Link TL-WR840 v4 and TP-Link TL-WR841 v13.
Specifications:
SOC: MediaTek MT7628NN
Flash: 8 MiB SPI
RAM: 64 MiB
WLAN: MediaTek MT7628NN
Ethernet: 5 ports (100M)
Installation Using the integrated tftp capability of the router:
1. Turn off the router.
2. Connect pc to one of the router LAN ports.
3. Set your PC IPv4 address to 192.168.0.66/24.
4. Run any TFTP server on the PC.
5. Put the recovery firmware on the root directory of TFTP server
and name the file tp_recovery.bin
6. Start the router by pressing power button while holding the
WPS/Reset button (or both WPS/Reset and WIFI buttons)
7. Router connects to your PC with IPv4 address 192.168.0.2,
downloads the firmware, installs it and reboots. LEDs are
flashing. Now you have OpenWrt installed.
8. Change your IPv4 PC address to something in 192.168.1.0/24
network or use DHCP to get an address from your OpenWrt router.
9. Done! You can login to your router via ssh.
Forum link:
https://forum.openwrt.org/t/add-support-for-tp-link-tl-wr850n-v2/66899
Signed-off-by: Andrew Freeman <labz56@gmail.com>
[squash an tidy up commits, sort nodes]
Signed-off-by: Darsh Patel <darshkpatel@gmail.com>
[minor commit message adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Like NAND-based devices, SPI-NOR based Netgear devices also share
a common setup for their images. This creates a common defition
for them in image/Makefile, so it can be reused across subtargets.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
WIZnet WizFi630s board name is written slightly different it its OEM
OpenWrt firmware. This causes an incompatibility warning during flashing
with sysupgrade. This patch is adding the vendor board name to the
supported devices list to avoid this warning. For initial flashing you
can use sysupgrade via command line or luci beside of TFTP.
Do not keep the OEM configuration during sysupgrade.
Signed-off-by: Tobias Welz <tw@wiznet.eu>
TP-Link RE200 v3 is a wireless range extender with Ethernet and 2.4G and 5G
WiFi with internal antennas. It's based on MediaTek MT7628AN+MT7610EN like the v2.
Specifications
--------------
- MediaTek MT7628AN (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 1T1R 5 GHz
- 1x 10/100 Mbps Ethernet
- 8x LED (GPIO-controlled), 2x button
Unverified:
- UART header on PCB (57600 8n1)
There are 2.4G and 5G LEDs in red and green which are controlled
separately.
MAC addresses
-------------
MAC address assignment has been done according to the RE200 v2.
The label MAC address matches the OpenWrt ethernet address.
Installation
------------
Web Interface
-------------
It is possible to upgrade to OpenWrt via the web interface. Simply flash
the -factory.bin from OEM. In contrast to a stock firmware, this will not
overwrite U-Boot.
Recovery
--------
Unfortunately, this devices does not offer a recovery mode or a tftp
installation method. If the web interface upgrade fails, you have to open
your device and attach serial console.
The device has not been opened for adding support. However, it is expected
that the behavior is similar to the RE200 v2. Instructions for serial console
and recovery may be checked out in commit 6d6f36ae78 ("ramips: add support
for TP-Link RE200 v2") or on the device's Wiki page.
Signed-off-by: Richard Fröhning <misanthropos@gmx.de>
[adjust commit title/message, sort support list]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
For the TP-Link 4M devices with tplink-v2-image recipe
(mktplinkfw2.c), there are two different flash layouts based
on the size of the (u)boot partition:
device uboot OEM firmware OpenWrt (incl. config)
tl-wr840n-v5 0x20000 0x3c0000 0x3d0000
tl-wr841n-v14 0x10000 0x3d0000 0x3e0000
In both cases, the 0x10000 config partition is used for the firmware
partition as well due to the limited space available and since it's
recreated by the OEM firmware anyway.
However, the TFTP flashing process will only copy data up to the
size of the initial (OEM) firmware size. Therefore, while we can
use the bigger partition to have additional erase blocks on the
device, we have to limit the image sizes to the TFTP limits.
So far, only one layout definition has been set up in mktplinkfw2.c
for 4M mediatek devices. This adds a second one and assigns them
to the devices so the image sizes are correctly restrained.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This commit adds support for the Jotale JS76x8 series development boards.
These devices have the following specifications:
- SOC: MT7628AN/NN, MT7688AN, MT7628DAN
- RAM of MT7628AN/NN and MT7688AN: 64/128/256 MB (DDR2)
- RAM of MT7628DAN: 64 MB (DDR2)
- FLASH:8/16/32 MB (SPI NOR)
- Ethernet:3x 10/100 Mbps ethernet ports (MT76x8 built-in switch)
- WIFI:1x 2T2R 2.4 GHz Wi-Fi
- LEDs:1x system status green LED, 1x wifi green LED,
3x ethernet green LED
- Buttons:1x reset button
- 1x microSD slot
- 4x USB 2.0 port
- 1x mini-usb debug UART
- 1x DC jack for main power (DC 5V)
- 1x TTL/RS232 UART
- 1x TTL/RS485 UART
- 13x GPIO header
- 1x audio codec(wm8960)
Installation via OpenWrt:
The original firmware is OpenWrt, so both LuCI and sysupgrade can be used.
Installation via U-boot web:
1. Power on board with reset button pressed, release it
after wifi led start blinking.
2. Setup static IP 192.168.1.123/4 on your PC.
3. Go to 192.168.1.8 in browser and upload "sysupgrade" image.
Installation via U-boot tftp:
1. Connect to serial console at the mini usb, which has been connected to UART0
on board (115200 8N1)
2. Setup static IP 192.168.1.123/4 on your PC.
3. Place openwrt-firmware.bin on your PC tftp server (192.168.1.123).
3. Connect one of LAN ports on board to your PC.
4. Start terminal software (e.g. screen /dev/ttyUSB0 115200) on PC.
5. Apply power to board.
6. Interrupt U-boot with keypress of "2".
7. At u-boot prompts:
Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N) Y
Input device IP (192.168.1.8) ==:192.168.1.8
Input server IP (192.168.1.123) ==:192.168.1.123
Input Linux Kernel filename (root_uImage) ==:openwrt-firmware.bin
8. board will download file from tftp server, write it to flash and reboot.
Signed-off-by: Robinson Wu <wurobinson@qq.com>
[add license to DTS files, fix state_default and reduce to the mimimum,
move phy0tpt trigger to DTS, drop ucidef_set_led_timer, fix network ports]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This reverts commit 1623defbdb.
As already stated in the reverted patch, the OEM firmware will
properly recreate the config partition if it is overwritten by
OpenWrt.
The main reason for adding the partition was the image size
restriction imposed by the 0x3d0000 limitation of the TFTP
flashing process. Addressing this by shrinking the firmware
partition is not a good solution to that problem, though:
1. For a working image, the size of the content has to be smaller
than the available space, so empty erase blocks will remain.
2. Conceptually, the restriction is on the image, so it makes sense
to implement it in the same way, and not via the partitioning.
Users could e.g. do initial flash with TFTP restriction with
an older image, and then sysupgrade into a newer one, so TFTP
restriction does not apply.
3. The (content) size of the recovery image is enforced to 0x3d0000
by the tplink-v2-image command in combination with
TPLINK_FLASHLAYOUT (flash layout in mktplinkfw2.c) anyway.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The config partition was missing from the flash layout of the device.
Although the stock firmware resets a corrupted config partition to the
default values, the TFTP flash with an image bigger than 0x3d0000 will
truncate the image as the bootloader only copies 0x3d0000 bytes to flash
during TFTP flashing.
Fixed by adding the config partition and shrinking the firmware
partition.
Fixes: 3fd97c522b ("ramips: add support for TP-Link TL-WR841n v14")
Signed-off-by: Alexander Müller <donothingloop@gmail.com>
