Update the devicetree files to switch the GS1900 devices over to the new
pinctrl and GPIO driver. Enable the drivers to ensure the nodes can be
used.
This may fix issues caused by bad RMW behaviour on the GPIO data lines,
or glitches due to setting the pin direction before the pin level.
Although the driver supports retaining GPIO state after a warm boot,
some bootloaders appear to apply a default configuration on boot, which
may cause an interrupt in PoE-PSE support.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Add pending patches to add RTL8231 support as a MDIO-bus attached
multi-functional device. This includes subdrivers for the pincontrol and
GPIO features, as well as the LED matrix support.
Leave the drivers disabled until required by a device.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Add a disabled node for the auxiliary MDIO bus, used to manage the
RTL8231 expanders. A simple-mfd parent node is added, at the same
(implied) address as the switch@1b000000 node, as the switch drivers
should anyway transistion to MFD subdivices at some point.
Additionally, two pinctrl-single node are added to allow the MDX pins to
be muxed correctly, in case the bootloader leaves these unconfigured.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Add a driver that exposes the auxiliary busses, used for the RTL8231
expanders, as a proper MDIO controller. The device must be instantiated
under an MFD device, so the driver should also be compatible with SoC
managed by an external CPU via SPI.
Leave the driver disabled in builds until required.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Run 'make kernel_oldconfig' to get an up-to-date config.
"# CONFIG_I2C_MUX_RTL9300 is not set" is retained, as the kernel module
build will selects CONFIG_I2C_MUX=m, on which this symbol depends.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Updating the driver patches for ipq40xx (correctly) removed the
ethernet0 alias from qcom-ipq4019.dtsi; however, on some devices this
alias is needed for the bootloader to set MAC addresses in the FDT.
As it is unknown which devices actually need the alias, simply add it to
all devices trees for now that enable the &gmac now to avoid regressions
from previous OpenWrt releases. The additional alias should not cause any
issues even when it is not needed.
A TODO comment is added to the same Device Trees to document that the
alias may not be needed (hopefully preventing it from being copied
unnecessarily to newly added devices in the future). The following
devices are known to need the alias for correct MAC address assignment,
so no TODO comment is added:
- FRITZ!Box 4040
- FRITZ!Box 7530
Fixes: cd9c7211241e ("ipq40xx: 6.1: use latest DSA and ethernet patches")
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Link: https://github.com/openwrt/openwrt/pull/17442
Signed-off-by: Robert Marko <robimarko@gmail.com>
According to datasheet, on AR9344 the switch and switch analog need to
be reset first before initiating a full reset.
Resetting these systems fixes spurious reset hangs on Atheros AR9344
SoCs.
Link: https://github.com/freifunk-gluon/gluon/issues/2904
Signed-off-by: David Bauer <mail@david-bauer.net>
This reverts commit 7ce4ed4829fafdd37a57681304ea91e3749bc3c8.
Turns out that this requires more work, so revert to prevent making the
LED uncontrollable.
Signed-off-by: Robert Marko <robimarko@gmail.com>
The Linksys MX4200v2 doesn't have the same LED controller as the MX4200v1 or MX4300. It comes with the STMicroelectronics LED1202 while the others come with the NXP PCA9633.
This LED controller has a driver under development which is currently being reviewed by the respective kernel maintainers. They are currently on v11.
Apart from the changes needed on the MX4200v2, this commit also amends the configuration of other devices affected by this change as the LED controller is no common to all of them as it was originally thought.
Signed-off-by: Manuel Fombuena <fombuena@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/17451
Signed-off-by: Robert Marko <robimarko@gmail.com>
This LED controller has a driver under development which is currently being reviewed by the respective kernel maintainers. They are currently on v11 which is included here.
The LED1202 is a 12-channel low quiescent current LED driver with:
* Supply range from 2.6 V to 5 V
* 20 mA current capability per channel
* 1.8 V compatible I2C control interface
* 8-bit analog dimming individual control
* 12-bit local PWM resolution
* 8 programmable patterns
If the led node is present in the controller then the channel is
set to active.
The output current can be adjusted separately for each channel by 8-bit
analog (current sink input) and 12-bit digital (PWM) dimming control. The
LED1202 implements 12 low-side current generators with independent dimming
control.
Internal volatile memory allows the user to store up to 8 different patterns,
each pattern is a particular output configuration in terms of PWM
duty-cycle (on 4096 steps). Analog dimming (on 256 steps) is per channel but
common to all patterns. Each device tree LED node will have a corresponding
entry in /sys/class/leds with the label name. The brightness property
corresponds to the per channel analog dimming, while the patterns[1-8] to the
PWM dimming control.
Signed-off-by: Manuel Fombuena <fombuena@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/17451
Signed-off-by: Robert Marko <robimarko@gmail.com>
I think I implemented the U-Boot handling incorrectly on M30 (saw the issue while porting M60 to OpenWrt). Maybe someone with more U-Boot experience can have a look at it.
What I understood until now:
Before flashing, `sw_tryactive` must be set to 0 because OpenWrt runs on partition 0
During reset after flashing, U-Boot executes the following line:
`boot_rd_auto_sw_img=if itest.s ${sw_tryactive} == 2; then run boot_by_part; else run boot_by_tryactive; fi`
As `sw_tryactive` was set to 0 before flashing, `boot_by_tryactive` will be executed:
`boot_by_tryactive=if itest.s ${sw_tryactive} == 0; then setenv sw_tryactive 2; setenv sw_active 1; saveenv; run ub0; else setenv sw_tryactive 2; setenv sw_active 2; saveenv; run ub1; fi`
As `sw_tryactive` was set to 0 before flashing, `sw_active` will be set to 1 and `ub0` will be executed:
`ub0=setenv bootpart 0; mtkboardboot; run ub0to1; uip main; reset`
If the OpenWrt boot is successful, `ub0to1` and `uip` main will never be executed. Only in case OpenWrt cannot be loaded, `mtkboardboot` will return and the fallback `ub0to1` is executed.
Conclusion: It's sufficient to set `sw_tryacitve` to 0 before flashing, the added code in `target/linux/mediatek/filogic/base-files/etc/init.d/bootcount` is useless.
In the worst case (/proc/cmdline doesn't contain `bootpart=ubi0` as expected), the bootpart variable would be set to 1 and causes starting the firmware from the second partition instead of the one on the first partition.
Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17298
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Images for certain devices are staring to become too large, as some
device only have 6MB available in their vendor partition layout for the
initial install. This is especially pressing for bootloaders only
supporting gzip compression.
Drop some packages from DEFAULT_PACKAGES that aren't strictly required
for a factory install. The user can always install more packages later
using opkg/apk, or via a sysupgrade to a custom build.
firewall4 is kept to ensure the most recent firewall package is selected
in builds including LuCI.
ethtool is kept as a frequently used diagnostics tool.
Link: https://github.com/openwrt/openwrt/pull/17450
Signed-off-by: Sander Vanheule <sander@svanheule.net>
We can use a package for the MV88E6060 DSA switch on the single
ath79 device that uses it, saving around 600 KB of memory on
all other devices (for the DSA infrastructure, mainly).
As far as I can see the TP-Link TL WR941 v2 is the only device
using MV88E6060 and the only device with a DSA switch overall.
However the ath79 people should look at this so I'm not
mistaken.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.ozlabs.org/project/openwrt/patch/20250102-ath79-mv88e6060-module-v1-1-c2a8e31e72fc@linaro.org/
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Sync buffalo.sh with the one in ramips/mt7621 to improve handling of the
TRX magic numbers of Buffalo WSR devices and switching sysupgrade method
between buffalo_upgrade_ubinized() and nand_do_upgrade().
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17408
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Unify the common part to the function and don't fixup trx when booting
with initramfs image.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17408
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Specification:
SoC: MediaTek MT7628AN
RAM: 128M DDR2, Etron Technology EM68C16CWQG-25H
Flash: 32M, cFeon EN25QH256A (Dual Boot, SPI)
Switch: MediaTek MT7628AN, 4 ports 100 Mbps
WiFi: MediaTek MT7628AN 2.4 GHz 802.11n and MediaTek MT7613BEN 5 GHz 802.11ac
USB: 1 port USB 2.0
GPIO: 3 buttons (Wi-Fi, Reset, FN), 4 LEDs (Power, Internet, FN, Wi-Fi), USB port power controls
Disassembly:
There are 2 screws at the bottom. After removing the screws, pry the gray plastic part around (it is secured with latches) and remove it.
UART Interface:
The UART interface can be connected to the 5 pin located between the WAN port and the RESET button.
Pins (from WAN port to Reset button): VCC, TX, RX, NC, GRD
Settings: 115200, 8N1
Flashing via OEM recovery software:
1. Download the OEM recovery software from the manufacturer's website
2. Download the firmware image (for OpenWRT it is *-squashfs-factory.bin), rename it to KN-1713_recovery.bin
3. Replace the file in the fw folder OEM recovery software with the file from step 2.
4. Run the OEM recovery software and follow the instructions.
Flashing via TFTP:
1. Connect your PC and router to port 1-3, configure PC interface using IP 192.168.1.2, mask 255.255.255.252
2. Serve the firmware image (for OpenWRT it is *-squashfs-factory.bin) renamed to KN-1713_recovery.bin via TFTP
3. Power up the router while pressing Reset button on the back
4. Release Restart button when Power LED starts blinking
To revert back to OEM firmware:
The return to the OEM firmware is carried out by using the methods described above with the help of the appropriate firmware image.
When using OEM bootloader, the firmware image size cannot exceed the size of one OEM «Firmware_x» partition or Kernel + rootFS size.
Signed-off-by: Anton Yu. Ivanusev <ivanusevanton@yandex.ru>
Link: https://github.com/openwrt/openwrt/pull/17382
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Avoids having to set the MAC in userspace.
Also added a mac-base change to set the wifi MACs. It's not clear if
upstream would want it once mac-base is upstreamed.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17064
Signed-off-by: Robert Marko <robimarko@gmail.com>
On the AVM 5490/5491, lan1, lan2 and wan ports are connected directly
to the internal GSWIP switch. The lan3 and lan4 ports are connected via
an external QCA8334 switch. This commit adds the missing entries in dts
and adds the driver module.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/17473
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Now we can set the mt76x8 SDXC pinmux in device tree.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/17446
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
These two packages are SDXC drivers for Mediatek mt762x series SoCs.
One is upstream implementation, and the other is downstream driver.
Installing them together will result in conflicts.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/17446
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
There are only 5 devices in mt76x8 sub-target selected the MTK SDXC
driver package. And they are all single ethernet port routers or dev
boards:
* LinkIt Smart 7688
* Onion Omega2+
* RAVPower RP-WD009
* VoCore VoCore2
* VoCore VoCore2-Lite
For these devices, they are using the ephy p1 - p4 as the SDXC IO
pins. Therefore, these GPIO pads must be configured in "digital"
IO mode.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/17446
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
After adding the correct package and pin group configurations,
the SDXC card slot can now function properly.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/17446
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The mt76x8 SDXC pin register definition is incompatible with the
mtmips generic pinctrl driver structure. This hack allows us to
mux the SDXC IO to different pin groups in device tree.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/17446
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In the MTK vendor driver, mt762x SDXC registers MSDC_PATCH_BIT and
MSDC_PATCH_BIT1 have different init values than upstream driver.
These magical values should have some help for the stability.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/17446
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Correct a few mistakes around dependencies and naming and unset
CONFIG_FIRMWARE_RP1 in RPi5B's config and instead of a builtin, build it
as a module.
Without this change, there are two entries for rp1.ko in
/lib/modules/$(uname -r)/modules.builtin due to how we strip the leading
directories when we generate it. See: package/kernel/linux/Makefile
around line 63.
% grep rp1.ko /lib/modules/$(uname -r)/modules.builtin
pwm-rp1.ko
clk-rp1.ko
rp1.ko
rp1.ko
The kernel log gets spammed with tons of superfluous warnings as a
results of the double entry:
daemon.warn modprobe: found duplicate builtin module rp1
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/17461
Signed-off-by: Robert Marko <robimarko@gmail.com>
Commit 8a477bafb4637e3499f69f569133039ce060559e backported an upstream patch
without refreshing the patches.
Fixes: 8a477bafb463 ("rockchip: fix phy reset on rk356x")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17474
Signed-off-by: Robert Marko <robimarko@gmail.com>
7a3bcd39ae1f r8169: use helper r8169_mod_reg8_cond to simplify rtl_jumbo_config
e3e9e9039fa6 r8169: align WAKE_PHY handling with r8125/r8126 vendor drivers
330dc2297c82 r8169: improve rtl_set_d3_pll_down
c507e96b5763 r8169: improve __rtl8169_set_wol
83cb4b470c66 r8169: remove leftover locks after reverted change
2cd02f2fdd8a r8169: improve initialization of RSS registers on RTL8125/RTL8126
a3d8520e6a19 r8169: align RTL8126 EEE config with vendor driver
4af2f60bf737 r8169: align RTL8125/RTL8126 PHY config with vendor driver
eb90f876b796 r8169: align RTL8125 EEE config with vendor driver
b8bd8c44a266 r8169: fix inconsistent indenting in rtl8169_get_eth_mac_stats
f75d1fbe7809 r8169: add support for RTL8125D
c4e64095c00c r8169: enable EEE at 2.5G per default on RTL8125B
d64113c6bb5e r8169: remove rtl_dash_loop_wait_high/low
1c105bacb160 r8169: avoid duplicated messages if loading firmware fails and switch to warn level
ac48430368c1 r8169: don't take RTNL lock in rtl_task()
e3fc5139bd8f r8169: implement additional ethtool stats ops
b8bf38440ba9 r8169: enable SG/TSO on selected chip versions per default
854d71c555df r8169: remove original workaround for RTL8125 broken rx issue
1ffcc8d41306 r8169: add support for the temperature sensor being available from RTL8125B
The following patches require backporting additional linux patches:
e2015942e90a r8169: replace custom flag with disable_work() et al
e340bff27e63 r8169: copy vendor driver 2.5G/5G EEE advertisement constraints
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
defer_list skbs held by NAPI can block releasing page pools.
Work around this by scheduling rx softirq on all CPUs while trying to release
a page pool.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The commit 7160820d742a ("phy: rockchip: naneng-combphy: fix phy reset")
was backported to kernel 6.6 branch by upstream, however the correspond
dtsi fixes was not, resulting the following error:
```
[ 0.225521] rockchip-naneng-combphy fe830000.phy: error -ENOENT: failed to get phy reset
[ 0.227467] rockchip-naneng-combphy fe840000.phy: error -ENOENT: failed to get phy reset
```
So backport the dtsi fixes here manually.
Fixes: 89b2356b8c2f ("kernel: bump 6.6 to 6.6.69")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/17468
Signed-off-by: Robert Marko <robimarko@gmail.com>
The MAC address of the GMAC is contained inside the CWMP-Account number on the label.
Similar fix as to the 4040 in b22d382ae4eaa1af42930115d91855f402314cac
Link #13240
Signed-off-by: Florian Maurer <f.maurer@outlook.de>
Link: https://github.com/openwrt/openwrt/pull/17467
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add 1920-24g-poe-180w to the mac address retrieval part of 02_network to
properly set the device's port MAC addresses.
This piece was missed when this device was added.
Fixes: b948c1e39b9e ("realtek: add support for HPE 1920-24G PoE-180W (JG925A)")
Link: https://github.com/openwrt/openwrt/pull/17460
Signed-off-by: James Sweeney <code@swny.io>
The extraneous closing parenthesis inside the case matching breaks
syntax of the network initialization script 02_network.
/bin/board_detect: /etc/board.d/02_network:
line 40: syntax error: unexpected newline (expecting ")")
Remove this character so board init is functional again.
Fixes: c8ea1aa970bf ("realtek: add support for HPE 1920-24G-PoE-370w")
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Just one of the devices uses the Marvell MV88E6060 DSA
switch so break this out from the generic kernel config
and into a package selected only by that single device
and probed at boot instead.
The big win is from being able to drop the dsa_core
(~600KB) kernel module out of the common kernel on
devices with no DSA switch.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some ixp4xx platforms with a proper RedBoot config do not
contain the per-ethernet interface npe_eth0_esa, but rather
a single entry named zcom_npe_esa.
Let's use this if fconfig can't find the primary key.
This is needed on the Netgear WG302 v1.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The WG302 v1 have a separate rootfs partition that we
simply just upgrade with a new rootfs image. The kernel
need to be updated on the TFTP server.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The WG302 v1 has 32MB of RAM so it can easily run OpenWrt,
however it lacks much flash: only 8 MB.
By just using the flash for rootfs and booting a kernel over
TFTP it works just fine.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Hardware information: (largely copied from 11275be)
---------------------
The HPE 1920-24G-PoE+ (180W) (JG925A) is a switch that is
part of the 1920 family which has 180W nominal PoE+ support.
Common with HPE 1920-24G:
- RTL8382 SoC
- 24 Gigabit RJ45 ports (built-in RTL8218B, 2 external RTL8218D)
- 4 SFP ports (external RTL8214FC)
- RJ45 RS232 port on front panel
- 32 MiB NOR Flash
- 128 MiB DDR3 DRAM
- PT7A7514 watchdog
HPE 1920-24G-PoE+ (180W):
- PoE chip
- 2 fans (40mm)
Known issues:
---------------------
- PoE LEDs are uncontrolled.
(Manual taken from f2f09bc)
Booting initramfs image:
------------------------
- Prepare a FTP or TFTP server serving the OpenWrt initramfs image and
connect the server to a switch port.
- Connect to the console port of the device and enter the extended
boot menu by typing Ctrl+B when prompted.
- Choose the menu option "<3> Enter Ethernet SubMenu".
- Set network parameters via the option "<5> Modify Ethernet Parameter".
Enter the FTP/TFTP filename as "Load File Name" ("Target File Name"
can be left blank, it is not required for booting from RAM). Note that
the configuration is saved on flash, so it only needs to be done once.
- Select "<1> Download Application Program To SDRAM And Run".
Initial installation:
---------------------
- Boot an initramfs image as described above, then use sysupgrade to
install OpenWrt permanently. After initial installation, the
bootloader needs to be configured to load the correct image file
- Enter the extended boot menu again and choose "<4> File Control",
then select "<2> Set Application File type".
- Enter the number of the file "openwrt-kernel.bin" (should be 1), and
use the option "<1> +Main" to select it as boot image.
- Choose "<0> Exit To Main Menu" and then "<1> Boot System".
NOTE: The bootloader on these devices can only boot from the VFS
filesystem which normally spans most of the flash. With OpenWrt, only
the first part of the firmware partition contains a valid filesystem,
the rest is used for rootfs. As the bootloader does not know about this,
you must not do any file operations in the bootloader, as this may
corrupt the OpenWrt installation (selecting the boot image is an
exception, as it only stores a flag in the bootloader data, but doesn't
write to the filesystem).
Example PoE config file (/etc/config/poe):
---------------------
config global
option budget '180'
config port
option enable '1'
option id '1'
option name 'lan8'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '2'
option name 'lan7'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '3'
option name 'lan6'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '4'
option name 'lan5'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '5'
option name 'lan4'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '6'
option name 'lan3'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '7'
option name 'lan2'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '8'
option name 'lan1'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '9'
option name 'lan16'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '10'
option name 'lan15'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '11'
option name 'lan14'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '12'
option name 'lan13'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '13'
option name 'lan12'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '14'
option name 'lan11'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '15'
option name 'lan10'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '16'
option name 'lan9'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '17'
option name 'lan24'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '18'
option name 'lan23'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '19'
option name 'lan22'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '20'
option name 'lan21'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '21'
option name 'lan20'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '22'
option name 'lan19'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '23'
option name 'lan18'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '24'
option name 'lan17'
option poe_plus '1'
option priority '2'
Signed-off-by: James Sweeney <code@swny.io>
Link: https://github.com/openwrt/openwrt/pull/17444
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Switch to using loader-kernel to accommodate
larger image sizes that are problematic for
many mt7621 uboots.
Signed-off-by: Jonathan Sturges <jsturges@redhat.com>
Link: https://github.com/openwrt/openwrt/pull/17389
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The debounce-interval of a gpio-keys node should be placed in the key
node itself, not in the main node. Move the properties added earlier and
fix the key node name while we're here.
Fixes: 4357f32d41eb ("realtek: debounce reset key for Zyxel GS1900")
Signed-off-by: Sander Vanheule <sander@svanheule.net>
During port to gluon, I saw that the primary mac is not correct. Updated DTS accordingly.
Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17429
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
