This adds support for the MikroTik RouterBOARD RBD52G-5HacD2HnD-TC
(hAP ac²), a indoor dual band, dual-radio 802.11ac
wireless AP with integrated omnidirectional antennae, USB port and five
10/100/1000 Mbps Ethernet ports.
See https://mikrotik.com/product/hap_ac2 for more info.
Specifications:
- SoC: Qualcomm Atheros IPQ4018
- RAM: 128 MB
- Storage: 16 MB NOR
- Wireless:
· Built-in IPQ4018 (SoC) 802.11b/g/n 2x2:2, 2.5 dBi antennae
· Built-in IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 2.5 dBi antennae
- Ethernet: Built-in IPQ4018 (SoC, QCA8075) , 5x 1000/100/10 port,
passive PoE in
- 1x USB Type A port
Installation:
Boot the initramfs image via TFTP and then flash the sysupgrade
image using "sysupgrade -n"
Signed-off-by: Robert Marko <robimarko@gmail.com>
While rebasing into setting bits instead of magic values,
I accidentally forgot to actually set the force bit.
Without it using the pins as GPIO-s did not actually work.
Fixes: b5c93ed ("ipq40xx: add Qualcomm QCA807x driver")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Both devices use u-boot env variables to boot OpenWrt from its flash
partition. Using u-boot envtools, it is possible to change the bootcmd
back to the stock firmware partition directly from OpenWrt without
attaching a serial cable or even physically accessing the device.
Signed-off-by: Jan Alexander <jan@nalx.net>
DTS files do not need to be executable. 644 is enough.
Fixes: 0fbdb51f76 ("ipq40xx: add Edgecore OAP-100 support")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[split by targets]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Since updating the MDIO driver, the probe will fail hard on any
PHY not present on the bus, while this was not the case prior.
Fixes commit 26b1f72381 ("ipq40xx: net: phy: ar40xx: remove PHY
handling")
Signed-off-by: David Bauer <mail@david-bauer.net>
Specifications:
SOC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core
RAM: 256 MiB
FLASH1: 4 MiB NOR
FLASH2: 128 MiB NAND
ETH: Qualcomm QCA8075
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11n/ac W2 2x2
INPUT: Reset
LED: Power, Internet
UART1: On board pin header near to LED (3.3V, TX, RX, GND), 3.3V without pin - 115200 8N1
OTHER: On board with BLE module - by cp210x USB serial chip
On board hareware watchdog with GPIO0 high to turn on, and GPIO4 for watchdog feed
Install via uboot tftp or uboot web failsafe.
By uboot tftp:
(IPQ40xx) # tftpboot 0x84000000 openwrt-ipq40xx-generic-glinet_gl-ap1300-squashfs-nand-factory.ubi
(IPQ40xx) # run lf
By uboot web failsafe:
Push the reset button for 10 seconds util the power led flash faster,
then use broswer to access http://192.168.1.1
Afterwards upgrade can use sysupgrade image.
Signed-off-by: Dongming Han <handongming@gl-inet.com>
Lets use the generic upstream phy_print_status() instead of doing
something similar by hand.
Before:
ess_edma c080000.edma: eth1: GMAC Link is up with phy_speed=1000
After:
ess_edma c080000.edma eth1: Link is Up - 1Gbps/Full - flow control rx/tx
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Since we now have a proper PHY driver for QCA807x and AR803x has already
been supported properly there is no need for the driver to be poking
on PHY registers for ethtool ops.
So, lets simply use the generic
phy_ethtool_ksettings_get/phy_ethtool_ksettings_set functions.
This also has the advantage of properly populating stuff other than
speeds like, transceiver type, MDI-X etc.
ethtool before:
root@OpenWrt:/# ethtool eth1
Settings for eth1:
Supported ports: [ TP MII ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
1000baseX/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: Yes
Supported FEC modes: Not reported
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
1000baseX/Full
Advertised pause frame use: Symmetric Receive-only
Advertised auto-negotiation: Yes
Advertised FEC modes: Not reported
Link partner advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Link partner advertised pause frame use: No
Link partner advertised auto-negotiation: No
Link partner advertised FEC modes: Not reported
Speed: 1000Mb/s
Duplex: Full
Port: Twisted Pair
PHYAD: 4
Transceiver: internal
Auto-negotiation: on
MDI-X: Unknown
Supports Wake-on: d
Wake-on: d
Current message level: 0x00000000 (0)
Link detected: yes
ethtool after:
root@OpenWrt:/# ethtool eth1
Settings for eth1:
Supported ports: [ TP MII ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
1000baseX/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: Yes
Supported FEC modes: Not reported
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
1000baseX/Full
Advertised pause frame use: Symmetric Receive-only
Advertised auto-negotiation: Yes
Advertised FEC modes: Not reported
Link partner advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Link partner advertised pause frame use: Symmetric Receive-only
Link partner advertised auto-negotiation: Yes
Link partner advertised FEC modes: Not reported
Speed: 1000Mb/s
Duplex: Full
Port: Twisted Pair
PHYAD: 4
Transceiver: external
Auto-negotiation: on
MDI-X: off (auto)
Supports Wake-on: d
Wake-on: d
Current message level: 0x00000000 (0)
Link detected: yes
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Since the new PHY driver manages each PHY individually and therefore
registers each PHY that is marked with gpio-controller; DT property as a
GPIO controller we need to convert old DT bindings to account for this.
Only 2 boards use this so its not much of an issue.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
PHY needs to be soft reset before starting it from ethernet driver as
AR40xx calibration will leave it in unwanted state.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Since we now have proper PHY driver for the QCA807x PHY-s, lets remove
PHY handling from AR40xx.
This removes PHY driver, PHY GPIO driver and PHY init code.
AR40xx still needs to handle PSGMII calibration as that requires R/W
from the switch, so I am unable to move it into PHY driver.
This also converted the AR40xx driver to use OF_MDIO to find the MDIO
bus as it now cant be set through the PHY driver.
So lets depend on OF_MDIO in KConfig.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
This adds driver for the Qualcomm QCA8072 and QCA8075 PHY-s.
They are 2 or 5 port IEEE 802.3 clause 22 compliant
10BASE-Te, 100BASE-TX and 1000BASE-T PHY-s.
They feature 2 SerDes, one for PSGMII or QSGMII connection with MAC,
while second one is SGMII for connection to MAC or fiber.
Both models have a combo port that supports 1000BASE-X and 100BASE-FX
fiber.
Each PHY inside of QCA807x series has 2 digitally controlled output only
pins that natively drive LED-s.
But some vendors used these to driver generic LED-s controlled by
user space, so lets enable registering each PHY as GPIO controller and
add driver for it.
This also adds the ability to specify DT properties so that 1000 Base-T
LED will also be lit up for 100 and 10 Base connections.
This is usually done by U-boot, but boards running mainline U-boot are
not configuring this yet.
These PHY-s are commonly used in Qualcomm IPQ40xx, IPQ60xx and IPQ807x
boards.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
With the reworked MDIO driver, EDMA will fail to get the MII BUS as it
used the MII BUS stored inside the MDIO structure private data.
This obviously does not work with the modernized driver, so lets switch
to using a purpose build of_mdio_find_bus() which will return the MII
BUS and only requires the MDIO node to be passed.
This is easy as we already have the node parsed.
Also, since we now require OF_MDIO add that as dependency.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
SOC: IPQ4018 / QCA Dakota
CPU: Quad-Core ARMv7 Processor rev 5 (v71) Cortex-A7
DRAM: 256 MiB
NOR: 32 MiB
ETH: Qualcomm Atheros QCA8075 (2 ports)
PLC: MaxLinear G.hn 88LX5152
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT: RESET, WiFi, PLC Button
LEDS: red/white home, white WiFi
To modify a retail device to run OpenWRT firmware:
1) Setup a TFTP server on IP address 192.168.0.100 and copy the OpenWRT
initramfs (initramfs-fit-uImage.itb) to the TFTP root as 'uploadfile'.
2) Power on the device while pressing the recessed reset button next to
the Ethernet ports. This causes the bootloader to retrieve and start
the initramfs.
3) Once the initramfs is booted, the device will come up with IP
192.168.1.1. You can then connect through SSH (allow some time for
the first connection).
4) On the device shell, run 'fw_printenv' to show the U-boot environment.
Backup this information since it contains device unique factory data.
5) Change the boot command to support booting OpenWRT:
# fw_setenv bootcmd 'sf probe && sf read 0x84000000 0x180000 0x400000 && bootm'
6) Change directory to /tmp, download the sysupgrade (e.g. through wget)
and install it with sysupgrade. The device will reboot into OpenWRT.
Notice that there is currently no support for booting the G.hn chip.
This requires userland software we lack the rights to share right now.
Signed-off-by: Stefan Schake <stefan.schake@devolo.de>
Device specifications:
* QCA IPQ4019
* 256 MB of RAM
* 32 MB of SPI NOR flash (w25q256)
- 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=20,variant=PlasmaCloud-PA2200
* 2T2R 5 GHz (channel 36-64)
- QCA9888 hw2.0 (PCI)
- requires special BDF in QCA9888/hw2.0/board-2.bin
bus=pci,bmi-chip-id=0,bmi-board-id=16,variant=PlasmaCloud-PA2200
* 2T2R 5 GHz (channel 100-165)
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=21,variant=PlasmaCloud-PA2200
* GPIO-LEDs for 2.4GHz, 5GHz-SoC and 5GHz-PCIE
* GPIO-LEDs for power (orange) and status (blue)
* 1x GPIO-button (reset)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
- phy@mdio3:
+ Label: Ethernet 1
+ gmac0 (ethaddr) in original firmware
+ used as LAN interface
- phy@mdio4:
+ Label: Ethernet 2
+ gmac1 (eth1addr) in original firmware
+ 802.3at POE+
+ used as WAN interface
* 12V 2A DC
Flashing instructions:
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.
Signed-off-by: Marek Lindner <marek.lindner@kaiwoo.ai>
[sven@narfation.org: prepare commit message, rebase, use all LEDs, switch
to dualboot_datachk upgrade script, use eth1 as designated WAN interface]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Device specifications:
* QCA IPQ4018
* 256 MB of RAM
* 32 MB of SPI NOR flash (w25q256)
- 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=PlasmaCloud-PA1200
* 2T2R 5 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=17,variant=PlasmaCloud-PA1200
* 3x GPIO-LEDs for status (cyan, purple, yellow)
* 1x GPIO-button (reset)
* 1x USB (xHCI)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
- phy@mdio4:
+ Label: Ethernet 1
+ gmac0 (ethaddr) in original firmware
+ used as LAN interface
- phy@mdio3:
+ Label: Ethernet 2
+ gmac1 (eth1addr) in original firmware
+ 802.3af/at POE(+)
+ used as WAN interface
* 12V/24V 1A DC
Flashing instructions:
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.
Signed-off-by: Marek Lindner <marek.lindner@kaiwoo.ai>
[sven@narfation.org: prepare commit message, rebase, use all LEDs, switch
to dualboot_datachk upgrade script, use eth1 as designated WAN interface]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
This reverts the usage of the S-Tag for separating LAN and WAN port on
the embedded switch. Many users complained about not being able to
manage C-Tag addition / removal on the switch as well as degraded
performance.
Fixes: commit 9da2b56760 ("ipq40xx: fix ethernet vlan double tagging")
Signed-off-by: David Bauer <mail@david-bauer.net>
The ASUS MAP-AC2200 suffers from a lower transmit/receive
signal power as compared to the stock firmware.
Upon investigation, it was discovered that stock firmware from
the GPL_MAP-AC2200_3.0.0.4.384.46249-g97d05bb.tar archive.
set the following GPIOs in "release/src/router/rc/init.c".
GPIO 44 and 46 have to be set to output high
GPIO 45 and 47 have to be set to output low
Here are some results, after activating the relevant
gpios through cmdline:
<https://forum.openwrt.org/t/asus-map-ac2200-low-transmit-receive-signal-5ghz/69005/12>
THX @ slh
Fixes: 9ad3967f14 ("ipq40xx: add support for ASUS Lyra")
Signed-off-by: Yushi Nishida <kyro2man@gmx.net>
[slightly rewritten commit, added missing <>)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The OpenMesh related files were not updated since a while and the new
coding style requirements weren't integrated. This can cause problems
for new devices when an author uses these files as starting point.
* use SPDX-License-Identifiers instead of full license texts
* drop linux,default-trigger with value default-off for LEDs
* led nodes with label "abc:xyz" should have name "xyz_abc"
* led DT labels for "xyz_abc" should be "led_xyz_abc"
* "m25p80@0" flash node should be renamed to "flash@0"
* drop unnecessary empty lines
Signed-off-by: Sven Eckelmann <sven@narfation.org>
[minor commit title and message adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This re-enables offloading features disabled by
commit 9da2b56760 ("ipq40xx: fix ethernet vlan double tagging").
Single-PHY devices use port-based VLANs on the switch, therefore no
S-TAG magic is involved here. Re-enabling these features restores
throughput back to 950 Mbit/s.
Reported-by: Jannis Pinter <jannis@pinterjann.is>
Signed-off-by: David Bauer <mail@david-bauer.net>
The target uses 5.4 as default kernel since 03/2020.
Kernel 4.19 support is not really maintained anymore, it does not
seem to be needed, and removing it will make upcoming driver
updates easier. Thus, remove it.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Upstream provides DTS(I) files for IPQ4019/AP-DK04.1, but we overwrite
them with local versions so far.
Remove the local files and use patches to be closer to upstream.
We already do the same for IPQ40xx/AP-DK01.1-C1.
Technically, this changes the compatible from "qcom,ipq4019" to
"qcom,ipq4019-dk04.1-c1", but it has never been implemented correctly
beforehand anyway.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This adds several stylistic and functional improvements of the recently
added Edgecore ECW5211, especially:
* Drop the local BDFs as those are already in the upstream under different names
* Add SPDX tag to DTS
* Add label MAC address
* Move LED trigger to DTS
* Remove unnecessary status="okay"
* Disable unused SS USB phy as the USB port only supports USB 2.0
* Make uboot-env partition writable
* Remove qcom,poll_required_dynamic property as the driver does not use it
* Tidy up the device recipe
Fixes: 4488b260a0 ("ipq40xx: add Edgecore ECW5211 support")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Acked-by: Robert Marko <robert.marko@sartura.hr>
Like in the previous patches for ath79 and ramips, this will remove
the "devicename" from LED labels in ipq40xx.
The devicename is removed in DTS files and 01_leds, and a migration
script is added. While at it, also harmonize capitalization of
wlan2G/wlan5G vs. wlan2g/wlan5g.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The "/dts-v1/;" identifier is supposed to be present once at the
top of a device tree file after the includes have been processed.
Therefore, adding it to a DTS _and_ a DTSI file is actually wrong,
as it will be present twice then (though the compiler does not
complain about it).
In ipq40xx, the dts-v1 statement is already included in
qcom-ipq4019.dtsi, so we don't have to add it anywhere at all.
However, based on the conditions stated above, this requires
qcom-ipq4019.dtsi to be included as the first file in any DTS(I).
Consequently, this patch removes all cases of dts-v1 for the
ipq40xx target, and moves the includes accordingly where necessary.
While at it, remove a few obviously unneeded includes on the way.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
.dts:226.17-230.4: Warning (spi_bus_reg): /soc/spi@78b6000/spi@1:
SPI bus unit address format error, expected "0"
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The Linksys MR8300 is based on QCA4019 and QCA9888
and provides three, independent radios.
NAND provides two, alternate kernel/firmware images
with fail-over provided by the OEM U-Boot.
Hardware Highlights:
SoC: IPQ4019 at 717 MHz (4 CPUs)
RAM: 512MB RAM
SoC: Qualcomm IPQ4019 at 717 MHz (4 CPUs)
RAM: 512M DDR3
FLASH: 256 MB NAND (Winbond W29N02GV, 8-bit parallel)
ETH: Qualcomm QCA8075 (4x GigE LAN, 1x GigE Internet Ethernet Jacks)
BTN: Reset and WPS
USB: USB3.0, single port on rear with LED
SERIAL: Serial pads internal (unpopulated)
LED: Four status lights on top + USB LED
WIFI1: 2x2:2 QCA4019 2.4 GHz radio on ch. 1-14
WIFI2: 2x2:2 QCA4019 5 GHz radio on ch. 36-64
WIFI3: 2x2:2 QCA9888 5 GHz radio on ch. 100-165
Support is based on the already supported EA8300.
Key differences:
EA8300 has 256MB RAM where MR8300 has 512MB RAM.
MR8300 has a revised top panel LED setup.
Installation:
"Factory" images may be installed directly through the OEM GUI using
URL: https://ip-of-router/fwupdate.html (Typically 192.168.1.1)
Signed-off-by: Hans Geiblinger <cybrnook2002@yahoo.com>
[copied Hardware-highlights from EA8300. Fixed alphabetical order.
fixed commit subject, removed bogus unit-address of keys,
fixed author (used Signed-off-By to From:) ]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Luma Home WRTQ-329ACN, also known as Luma WiFi System, is a dual-band
wireless access point.
Specification
SoC: Qualcomm Atheros IPQ4018
RAM: 256 MB DDR3
Flash: 2 MB SPI NOR
128 MB SPI NAND
WIFI: 2.4 GHz 2T2R integrated
5 GHz 2T2R integrated
Ethernet: 2x 10/100/1000 Mbps QCA8075
USB: 1x 2.0
Bluetooth: 1x 4.0 CSR8510 A10, connected to USB bus
LEDS: 16x multicolor LEDs ring, controlled by MSP430G2403 MCU
Buttons: 1x GPIO controlled
EEPROM: 16 Kbit, compatible with AT24C16
UART: row of 4 holes marked on PCB as J19, starting count from the side
of J19 marking on PCB
1. GND, 2. RX, 3. TX, 4. 3.3V
baud: 115200, parity: none, flow control: none
The device supports OTA or USB flash drive updates, unfotunately they
are signed. Until the signing key is known, the UART access is mandatory
for installation. The difficult part is disassembling the casing, there
are a lot of latches holding it together.
Teardown
Prepare three thin, but sturdy, prying tools. Place the device with back
of it facing upwards. Start with the wall having a small notch. Insert
first tool, until You'll feel resistance and keep it there. Repeat the
procedure for neighbouring walls. With applying a pressure, one edge of
the back cover should pop up. Now carefully slide one of the tools to
free the rest of the latches.
There's no need to solder pins to the UART holes, You can use hook clips,
but wiring them outside the casing, will ease debuging and recovery if
problems occur.
Installation
1. Prepare TFTP server with OpenWrt initramfs image.
2. Connect to UART port (don't connect the voltage pin).
3. Connect to LAN port.
4. Power on the device, carefully observe the console output and when
asked quickly enter the failsafe mode.
5. Invoke 'mount_root'.
6. After the overlayfs is mounted run:
fw_setenv bootdelay 3
This will allow to access U-Boot shell.
7. Reboot the device and when prompted to stop autoboot, hit any key.
8. Adjust "ipaddr" and "serverip" addresses in U-Boot environment, use
'setenv' to do that, then run following commands:
tftpboot 0x84000000 <openwrt_initramfs_image_name>
bootm 0x84000000
and wait till OpenWrt boots.
9. In OpenWrt command line run following commands:
fw_setenv openwrt "setenv mtdids nand1=spi_nand; setenv mtdparts mtdparts=spi_nand:-(ubi); ubi part ubi; ubi read 0x84000000 kernel; bootm 0x84000000"
fw_setenv bootcmd "run openwrt"
10. Transfer OpenWrt sysupgrade image to /tmp directory and flash it
with:
ubirmvol /dev/ubi0 -N ubi_rootfs
sysupgrade -v -n /tmp/<openwrt_sysupgrade_image_name>
11. After flashing, the access point will reboot to OpenWrt, then it's
ready for configuration.
Reverting to OEM firmware
1. Execute installation guide steps: 1, 2, 3, 7, 8.
2. In OpenWrt command line run following commands:
ubirmvol /dev/ubi0 -N rootfs_data
ubirmvol /dev/ubi0 -N rootfs
ubirmvol /dev/ubi0 -N kernel
ubirename /dev/ubi0 kernel1 kernel ubi_rootfs1 ubi_rootfs
ubimkvol /dev/ubi0 -S 34 -N kernel1
ubimkvol /dev/ubi0 -S 320 -N ubi_rootfs1
ubimkvol /dev/ubi0 -S 264 -N rootfs_data
fw_setenv bootcmd bootipq
3. Reboot.
Known issues
The LEDs ring doesn't have any dedicated driver or application to control
it, the only available option atm is to manipulate it with 'i2cset'
command. The default action after applying power to device is spinning
blue light. This light will stay active at all time. To disable it
install 'i2c-tools' with opkg and run:
i2cset -y 2 0x48 3 1 0 0 i
The light will stay off until next cold boot.
Additional information
After completing 5. step from installation guide, one can disable asking
for root password on OEM firmware by running:
sed -e 's/root❌/root::/' -i /etc/passwd
This is useful for investigating the OEM firmware. One can look
at the communication between the stock firmware and the vendor's
cloud servers or as a way of making a backup of both flash chips.
The root password seems to be constant across all sold devices.
This is output of 'led_ctl' from OEM firmware to illustrate
possibilities of LEDs ring:
Usage: led_ctl [status | upgrade | force_upgrade | version]
led_ctl solid COLOR <brightness>
led_ctl single COLOR INDEX <brightness 0 - 15>
led_ctl spinning COLOR <period 1 - 16 (lower = faster)>
led_ctl fill COLOR <period 1 - 16 (lower = faster)>
( default is 5 )
led_ctl flashing COLOR <on dur 1 - 128> <off dur 1 - 128>
(default is 34) ( default is 34 )
led_ctl pulsing COLOR
COLOR: red, green, blue, yellow, purple, cyan, white
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
[squash "ipq-wifi: add BDFs for Luma Home WRTQ-329ACN" into commit,
changed ubi volumes for easier integration, slightly reworded
commit message, changed ubi volume layout to use standard names all
around]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
SPDX moved from GPL-2.0 to GPL-2.0-only and from GPL-2.0+ to
GPL-2.0-or-later. Reflect that in the SPDX license headers.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The ethernet ports on the AVM FRITZRepeater 3000 are not separated
between LAN and WAN in the stock firmware. OpenWrt currently abstracts
port 4 as eth0 and port 5 as eth1, bridging them in the kernel.
This patch adjusts the GMAC port bitmasks and default bitmask for ar40xx
to bridge them on the switch, avoiding traffic on both ports to pass
thru the CPU.
Signed-off-by: David Bauer <mail@david-bauer.net>
flashing the unit
* first update to latest edcore FW as per the PDF instructions
* boot the initramfs
- tftpboot 0x88000000 openwrt-ipq40xx-generic-edgecore_oap100-initramfs-fit-uImage.itb; bootm
* inside the initramfs call the following commiands
- ubiattach -p /dev/mtd0
- ubirmvol /dev/ubi0 -n0
- ubirmvol /dev/ubi0 -n1
- ubirmvol /dev/ubi0 -n2
* scp the sysupgrade image to the board and call
- sysupgrade -n openwrt-ipq40xx-generic-edgecore_oap100-squashfs-nand-sysupgrade.bin
Signed-off-by: John Crispin <john@phrozen.org>
This patch adds support for the Edgecore ECW5211 indoor AP.
Specification:
- SoC: Qualcomm Atheros IPQ4018 ARMv7-A 4x Cortex A-7
- RAM: 256MB DDR3
- NOR Flash: 16MB SPI NOR
- NAND Flash: 128MB MX35LFxGE4AB SPI-NAND
- Ethernet: 2 x 1G via Q8075 PHY connected to ethernet adapter via PSGMII (802.3af POE IN on eth0)
- USB: 1 x USB 3.0 SuperSpeed
- WLAN: Built-in IPQ4018 (2x2 802.11bng, 2x2 802.11 acn)
- CC2540 BLE connected to USB 2.0 port
- Atmel AT97SC3205T I2C TPM
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Buffalo WTR-M2133HP is a Tri-Band router based on IPQ4019.
Specification
-------------
- SoC: Qualcomm IPQ4019
- RAM: 512MiB
- Flash Memory: NAND 128MiB (MXIC MX30LF1G18AC)
- Wi-Fi: Qualcomm IPQ4019 (2.4GHz, 1ch - 13ch)
- Wi-Fi: Qualcomm IPQ4019 (5GHz, 36ch - 64ch)
- Wi-Fi: Qualcomm QCA9984 (2T2R, 5GHz, 100ch - 140ch)
- Ethernet: 4x 10/100/1000 Mbps (1x WAN, 3x LAN)
- LED: 4x white LED, 4x orange LED, 1x blue LED
- USB: 1x USB 3.0 port
- Input: 2x tactile switch, 2x slide switch (2x SP3T)
- Serial console: 115200bps, pinheader JP5 on PCB
- Power: DC 12V 2A
Flash instruction
-----------------
1. Set up a TFTP server (IP address: 192.168.11.10)
2. Rename "initramfs-fit-uImage.itb" to "WTR-M2133HP-initramfs.uImage"
and put it into the TFTP server directory.
3. Connect the TFTP server and WTR-M2133HP.
4. Hold down the AOSS button, then power on the router.
5. After booting OpenWrt initramfs image, connect to the router by SSH.
6. Transfer "squashfs-nand-factory.ubi" to the router.
7. Execute the following commands.
# ubidetach -p /dev/mtd15
# ubiformat /dev/mtd15 -f /tmp/openwrt-ipq40xx-generic-buffalo_wtr-m2133hp-squashfs-nand-factory.ubi
# fw_setenv bootcmd bootipq
8. Perform reboot.
Recover to stock firmware
-------------------------
1. Execute the following command.
# fw_setenv bootcmd bootbf
2. Reboot and wait several minutes.
Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
Specifications:
SOC: Qualcomm IPQ4029 (DAKOTA) ARM Quad-Core
RAM: 512 MiB
FLASH1: 16 MiB NOR - SPI0
FLASH2: 8 GiB eMMC
ETH: Qualcomm QCA8075
WLAN1: Qualcomm Atheros QCA4029 2.4GHz 802.11b/g/n 2x2
WLAN2: Qualcomm Atheros QCA4029 5GHz 802.11n/ac W2 2x2
INPUT: Reset, WPS
LED: Power, Mesh, WLAN
UART1: On board pin header near to LED (3.3V, TX, RX, GND), 3.3V without pin - 115200 8N1
UART2: On board with BLE module
SPI1: On board socket for Zigbee module
Install via tftp
- NB: need to flash transition image firstly
Firstly install transition image:
(IPQ40xx) # tftpboot 0x84000000 s1300-factory-to-openwrt.img
(IPQ40xx) # sf probe && imgaddr=0x84000000 && source :script
Secondly install openwrt sysupgrade bin:
(IPQ40xx) # run lf
Revert to factory image:
(IPQ40xx) # tftpboot 0x84000000 s1300-openwrt-to-factory.img
(IPQ40xx) # sf probe && imgaddr=0x84000000 && source :script
The kernel and rootfs of factory firmware are on eMMC, and openwrt
firmware is on NOR flash. The transition image includes U-boot
and partition table, which decides where to load kernel and rootfs.
After you firstly install openwrt image, you can switch between
factory and openwrt firmware by flashing transition image.
Signed-off-by: Dongming Han <handongming@gl-inet.com>
The DTS files in files-4.19 and files-5.4 are exactly identical
except for one file (qcom-ipq4018-emr3500.dts), which is only
present for 5.4.
Since there is no point in maintaining all these identical files
twice, this patch moves them to the "files" directory.
If there ever was a new kernel with substantial DTS changes, a
new folder would need to be introduced anyway and could easily be
done.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
