ATH_REG_DYNAMIC_USER_REG_HINTS is currently not being set as mac80211
tries to set it as m which is not possible as its boolean only.
Since its used alongside user regulatory, move it to USER_REGD.
This is required for ath11k to accept regulatory changes, otherwise
it wont accept any changes and will simply force US.
Signed-off-by: Robert Marko <robimarko@gmail.com>
From the patch series description:
Several security issues in the 802.11 implementations were found by
Mathy Vanhoef (New York University Abu Dhabi), who has published all
the details at
https://papers.mathyvanhoef.com/usenix2021.pdf
Specifically, the following CVEs were assigned:
* CVE-2020-24586 - Fragmentation cache not cleared on reconnection
* CVE-2020-24587 - Reassembling fragments encrypted under different
keys
* CVE-2020-24588 - Accepting non-SPP A-MSDU frames, which leads to
payload being parsed as an L2 frame under an
A-MSDU bit toggling attack
* CVE-2020-26139 - Forwarding EAPOL from unauthenticated sender
* CVE-2020-26140 - Accepting plaintext data frames in protected
networks
* CVE-2020-26141 - Not verifying TKIP MIC of fragmented frames
* CVE-2020-26142 - Processing fragmented frames as full frames
* CVE-2020-26143 - Accepting fragmented plaintext frames in
protected networks
* CVE-2020-26144 - Always accepting unencrypted A-MSDU frames that
start with RFC1042 header with EAPOL ethertype
* CVE-2020-26145 - Accepting plaintext broadcast fragments as full
frames
* CVE-2020-26146 - Reassembling encrypted fragments with non-consecutive
packet numbers
* CVE-2020-26147 - Reassembling mixed encrypted/plaintext fragments
In general, the scope of these attacks is that they may allow an
attacker to
* inject L2 frames that they can more or less control (depending on the
vulnerability and attack method) into an otherwise protected network;
* exfiltrate (some) network data under certain conditions, this is
specific to the fragmentation issues.
A subset of these issues is known to apply to the Linux IEEE 802.11
implementation (mac80211). Where it is affected, the attached patches
fix the issues, even if not all of them reference the exact CVE IDs.
In addition, driver and/or firmware updates may be necessary, as well
as potentially more fixes to mac80211, depending on how drivers are
using it.
Specifically, for Intel devices, firmware needs to be updated to the
most recently released versions (which was done without any reference
to the security issues) to address some of the vulnerabilities.
To have a single set of patches, I'm also including patches for the
ath10k and ath11k drivers here.
We currently don't have information about how other drivers are, if
at all, affected.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Missing braces in a macro were leading to badly working rates sometimes
getting a success probabilty of 1.0
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When transmitting to a receiver in dynamic SMPS mode, all transmissions that
use multiple spatial streams need to be sent using CTS-to-self or RTS/CTS to
give the receiver's extra chains some time to wake up.
This fixes the tx rate getting stuck at <= MCS7 for some clients, especially
Intel ones, which make aggressive use of SMPS.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
On hardware that supports this, this will improve performance by passing
802.3 frames from the hardware to the stack
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The removed patches were applied upstream.
This adapts ath10k-ct and mt76 to changed APIs.
nl80211.h in iw is updated to match the version from backports.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The removed patches were applied upstream.
Remove the 300-mac80211-optimize-skb-resizing.patch.
This patch was not applied upstream, but it conflicts with upstream
changes and needs bigger changes. It was applied with Felix to remove
this patch for now. It should be reworked and then send upstream later.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Multiple sources are hosted on OpenWrts source server only. The source
URLs to point to the server vary based on different epochs in OpenWrts
history.
Replace all by @OPENWRT which is an "empty" mirror, therefore using the
fallback servers sources.cdn.openwrt.org and sources.openwrt.org.
Signed-off-by: Paul Spooren <mail@aparcar.org>
If the driver uses .sta_add, station entries are only uploaded after the sta
is in assoc state. Fix early station rate table updates by deferring them
until the sta has been uploaded
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Enable support for the Ubiquiti UniFi Outdoor+ RF filter via
device-tree. The old way of using platform data is not required anymore,
as it was only used on the now removed ar71xx target.
Signed-off-by: David Bauer <mail@david-bauer.net>
This patch adds wil6210 driver for Wilocity/QCA based 802.11ad
PCI cards.
Driver uses cfg80211 and nl80211 but not mac80211.
Integration for UCI and LuCI will come in other patches.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Legacy minstrel is essentially unmaintained and was showing poor performance
Replace it with minstrel_ht and improve rate selection and sampling behavior
Signed-off-by: Felix Fietkau <nbd@nbd.name>
As of hostapd upstream commit 7d2ed8ba "Remove CONFIG_IEEE80211W build parameter"
https://w1.fi/cgit/hostap/commit?id=7d2ed8bae86a31dd2df45c24b3f7281d55315482
802.11w feature is always enabled in the build time.
It doesn't make sense to opt-in 802.11w per driver as hostapd will always
be compiled with this feature enabled.
As suggested by Hauke Mehrtens, for now keep 11w enabled in build_features.h
for compatibility reasons. This option will be dropped when LuCI is adjusted.
Signed-off-by: Dobroslaw Kijowski <dobo90@gmail.com>
Testing with hwsim reveals two problems:
1. phyX/addresses has two addresses and mac80211_get_addr keeps
returning the last one when asked for more;
2. The base address has the local bit set and the operation unsets it.
Fix both.
Fixes: 866790fd82
Reported-by: Zero_Chaos
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Remove deferred sampling code which does not work well with rate tables +
probing.
Fix tx status handling if the first invalid rate idx is not set to -1
Signed-off-by: Felix Fietkau <nbd@nbd.name>
A lot of devices running OpenWrt x86 arch (32 or 64 bit) are either
"home-made routers" or devices that use PC class OEM components.
This commit enables OEM cards support on those devices by default.
Signed-off-by: Rafał Dzięgiel <rafostar.github@gmail.com>
[reformat commit message]
Signed-off-by: David Bauer <mail@david-bauer.net>
If mac80211_setup_supplicant() is called with enabled=0 then it should just
destroy the interface and remove the configuration from wpa_supplicant. But
the ubus method call always returned
Command failed: Method not found
because the actual name of the method is "config_remove".
Fixes: b5516603dd ("mac80211: more wifi reconf related fixes")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
[bump PKG_RELEASE]
Signed-off-by: David Bauer <mail@david-bauer.net>
hostapd_set_bss_options expects the PHY as second and the VIF as third
argument. However, only the VIF was passed as second argument without a
third argument at all.
This was never a problem, as both PHY and VIF were never accessed.
However, with FTM support the PHY is needed to determine the HW support
when configuring the BSS.
Signed-off-by: David Bauer <mail@david-bauer.net>
rt2800 olny gives you survey for current channel.
Survey-based ACS algorithms are failing to perform their job when working
with rt2800.
Make rt2800 save survey for every channel visited and be able to give away
that information.
There is a bug registred https://dev.archive.openwrt.org/ticket/19081 and
this patch solves the issue.
Signed-off-by: Markov Mikhail <markov.mikhail@itmh.ru>
After the status rework, ieee80211_tx_status_ext is leaking un-acknowledged
packets for stations in powersave mode.
To fix this, move the code handling those packets from __ieee80211_tx_status
into ieee80211_tx_status_ext
Reported-by: Tobias Waldvogel <tobias.waldvogel@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The vendor driver does things differently based on what it finds in the
SoC's CHIP_VER register, which should tell whether this is MT7620N or
MT7620A (PKG) and probably also the revision (VER) and most likely
also something about the silicon implementer (ECO).
Introduce codepaths just like the ones in the vendor driver to handle
the different chips properly.
Some of those paths are most likely dead code and left-overs from FPGA
versions or early prototypes of the chip. It'd thus be great if people
can post their kernel logs, at least the line telling the chip version
and eco, so we know what's actually out there in the wild -- all I
could find is
[ 0.000000] SoC Type: Ralink MT7620A ver:2 eco:6
and
[ 0.000000] SoC Type: Ralink MT7620N ver:2 eco:6
which would make things easier, as then we really just need to know
whether it's MT7620N or MT7620A and not care about FPGA or prototypes
with ver <= 1 and eco <= 2.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This is useful to bring up multiple client mode interfaces on a single
channel much faster without having to scan through a lot of channels
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When the nulldata frame was acked, the probe send count needs to be reset,
otherwise it will keep increasing until the connection is considered dead,
even though it fine.
Reported-by: Georgi Valkov <gvalkov@abv.bg>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Some 5GHz wifi interfaces, especially in Tri-band routers, can't use
channel 36. In these cases, the default configuration for 5GHz
interfaces, once enabled, doesn't work.
This patch selects the first non-disabled channel for 5GHz interfaces.
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
Minor cleanup and code reorganization, along with a change to not disable
offload anymore when a tkip or sw crypto key is added
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Discussion on the mailing list reveals that this target has active
users. As we are finally able to upgrade this target to kernel 5.4,
add it back to master.
This reverts commit 7d29a55714 ("ath25: drop target") and
immediately moves the relevant files to 5.4, without touching
the content.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This target still only works with kernel 4.14, and not so recent
attempts of getting newer kernel versions supported did not lead
to success. Therefore, drop the target, as we are already two
LTS kernel versions ahead and it does not seem like anybody will
pick up the work.
Patchwork series:
https://patchwork.ozlabs.org/project/openwrt/list/?series=169991&state=*
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This target has been mostly replaced by ath79 and won't be included
in the upcoming release anymore. Finally put it to rest.
This also removes all references in packages, tools, etc. as well as
the uboot-ar71xx and vsc73x5-ucode packages.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The driver currently only support managed and monitor mode
Changes since v1:
- drop the @DRIVER_11N_SUPPORT dependency
Signed-off-by: mohammad rasim <mohammad.rasim96@gmail.com>
mac80211 reports a packet loss event to user space when 50 consecutive packets
were not acked. On a high throughput link with long aggregates and sudden
link changes, this can trigger way too easily.
Mitigate false positives by only triggering the event on a packet loss if
no ACK was received for at least a second
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Exchange the patch fixing the kernel ringbuffer WARNING flood for the
one accepted upstream.
Fixes commit a956c14d6a ("mac80211: util: don't warn on missing sband
iftype data")
Signed-off-by: David Bauer <mail@david-bauer.net>
Testmode commands are typically only used for manufacturing or vendor specific
debugging features, so they should not be in the default image
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Don't kill the wireless daemon on teardown. hostapd as well as
wpa_supplicant are managed by procd which would detect the shutdown of
either process as a crash loop.
Signed-off-by: David Bauer <mail@david-bauer.net>
When retrieving the PID for hostapd and wpa_supplicant via ubus the
wrong service name is currently used. This leads to the following error
in the log:
netifd: radio0 (1409): WARNING (wireless_add_process):
executable path /usr/sbin/wpad does not match process path (/proc/exe)
Fixing the service name retrieves the correct PID and therefore the
warning won't occur.
Signed-off-by: David Bauer <mail@david-bauer.net>
The kernel currently floods the ringbuffer with warnings when adding a
mesh interface for a device not support HE 6GHz modes.
Return without warning in this case, as mesh_add_he_6ghz_cap_ie calls
ieee80211_ie_build_he_6ghz_cap regardless of the supported interface
modes.
Signed-off-by: David Bauer <mail@david-bauer.net>
The following patches:
* 972-ath10k_fix-crash-due-to-wrong-handling-of-peer_bw_rxnss_override-parameter.patch
* 973-ath10k_fix-band_center_freq-handling-for-VHT160-in-recent-firmwares.patch
are replaced by this commit in the upstream kernel:
* 3db24065c2c8 ("ath10k: enable VHT160 and VHT80+80 modes")
The following patches were applied upstream:
* 001-rt2800-enable-MFP-support-unconditionally.patch
* 090-wireless-Use-linux-stddef.h-instead-of-stddef.h.patch
The rtw88 driver is now split into multiple kernel modules, just put it
all into one OpenWrt kernel package.
rtl8812au-ct was patched to compile against the mac80211 from kernel
5.8, but not runtime tested.
Add a patch which fixes ath10k on IPQ40XX, this patch was send upstream
and fixes a crash when loading ath10k on this SoC.
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [ipq40xx/ map-ac2200]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Currently a device which has a DFS channel selected using the UCI
channel setting might switch to a non-DFS channel in case no chanlist is
provided (UCI setting "channels") when the radio detects a DFS event.
Automatically add a chanlist consisting of the configured channel when
the device does not operate in auto-channel mode and no chanlist set to
circumvent this issue.
Signed-off-by: David Bauer <mail@david-bauer.net>
Make sure RF5592 is set for RT5592 chip which apparently sometimes
doesn't have RF defined (but always comes with RF5592).
This patch was originally submitted on linux-wireless by
Tom Psyborg <pozega.tomislav@gmail.com> but got rejected.
Turns out the patch is actually needed.
Reported-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This can be useful when a DFS channel is configured, as the ACS channel
list is taken into account when switching channels after a radar event.
For example, this allows to prevent the SRD channels from being used in
that case.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
[reorder structure]
Signed-off-by: David Bauer <mail@david-bauer.net>
ath9k will already fallback on software-crypto for chipsets not
supporting IEEE802.11w (MFP). So advertising MFP is not dependent
on disabling HW crypto for all traffic entirely.
Tested on Sonicwall SonicPoint Ni (AR9132)
Signed-off-by: David Bauer <mail@david-bauer.net>
mac80211_get_addr is called from mac80211_generate_mac, where the local variable
initialisation id="${macidx:-0}" suggests that macidx is not always defined.
Probably, idx was supposed to be used instead of $(($macidx + 1)).
Fixes: 4d99db168c ("mac80211: try to get interface addresses from wiphy sysfs 'addresses' if no mask is set")
Signed-off-by: Leon M. George <leon@georgemail.eu>
This option allows adding the ath9k ADC register output as a source
of randomness into the Linux entropy pool at sufficient quality
random data (at least 10 bits and up to 22 bits of min-entropy for
a 32-bit value).
Fixes FS#1444
Signed-off-by: Alan Swanson <reiver@improbability.net>
This patch adds support for 2 new uci sections.
config wifi-vlan
# iface is optional. if it is not defined the vlan will apply
# to all interfaces
option iface default_radio0
option name guest
option vid 100
option network guest
config wifi-station
# iface is optional. if it is not defined the station will apply
# to all interfaces
option iface default_radio0
# mac is optional. if it is not defined it will be a catch all
# for any sta using this key
option mac '00:11:22:33:44:55'
# vid is optional. if it is not defined, the sta will be part of
# the primary iface.
option vid 100
option key testtest
With this patch applied it is possible to use multiple PSKs on a single BSS.
Signed-off-by: John Crispin <john@phrozen.org>
From: Rui Salvaterra <rsalvaterra@gmail.com>
Date: Mon, 25 May 2020 14:49:07 +0100
Subject: [PATCH] rt2800: enable MFP support unconditionally
This gives us WPA3 support out of the box without having to manually disable
hardware crypto. The driver will fall back to software crypto if the connection
requires management frame protection.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
When configuring the radio in legacy mode from luci, the htmode is not set
correctly to NOHT, causing the radio in mesh mode to be set to HT40.
Signed-off-by: Enrique Rodríguez Valencia <enrique.rodriguez@galgus.net>
This fixes the following compile error seen on the mpc85xx target:
CC [M] /linux-mpc85xx_p2020/backports-5.7-rc3-1/drivers/net/wireless/intersil/orinoco/main.o
In file included from /builder/shared-workdir/build/staging_dir/toolchain-powerpc_8540_gcc-8.4.0_musl/include/stddef.h:17,
from /linux-mpc85xx_p2020/backports-5.7-rc3-1/include/uapi/linux/wireless.h:77,
from /linux-mpc85xx_p2020/backports-5.7-rc3-1/include/linux/wireless.h:13,
from /linux-mpc85xx_p2020/backports-5.7-rc3-1/drivers/net/wireless/intersil/orinoco/main.c:89:
/builder/shared-workdir/build/staging_dir/toolchain-powerpc_8540_gcc-8.4.0_musl/include/bits/alltypes.h:106:15: error: conflicting types for 'ptrdiff_t'
typedef _Addr ptrdiff_t;
^~~~~~~~~
In file included from /linux-mpc85xx_p2020/backports-5.7-rc3-1/backport-include/linux/types.h:4,
from ./include/linux/list.h:5,
from /linux-mpc85xx_p2020/backports-5.7-rc3-1/backport-include/linux/list.h:3,
from ./include/linux/module.h:9,
from /linux-mpc85xx_p2020/backports-5.7-rc3-1/backport-include/linux/module.h:3,
from /linux-mpc85xx_p2020/backports-5.7-rc3-1/drivers/net/wireless/intersil/orinoco/main.c:79:
./include/linux/types.h:65:28: note: previous declaration of 'ptrdiff_t' was here
typedef __kernel_ptrdiff_t ptrdiff_t;
^~~~~~~~~
scripts/Makefile.build:265: recipe for target '/linux-mpc85xx_p2020/backports-5.7-rc3-1/drivers/net/wireless/intersil/orinoco/main.o' failed
Fixes: 289c632425 ("mac80211: Update to version 5.7-rc3-1")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
