NEC Aterm WR9500N is a 2.4/5 GHz band 11n (Wi-Fi 4) router, based on
AR9344.
Specification:
- SoC : Atheros AR9344
- RAM : DDR2 128 MiB (2x Nanya NT5TU32M16DG-AC)
- Flash : SPI-NOR 16 MiB (Macronix MX25L12845EMI-10G)
- WLAN : 2.4/5 GHz
- 2.4 GHz : 2T2R, Atheros AR9344 (SoC)
- 5 GHz : 3T3R, Atheros AR9380
- Ethernet : 5x 10/100/1000 Mbps
- switch : Atheros AR8327
- LEDs/Keys (GPIO): 12x/4x
- note : all LEDs are controlled by ath9k chip (AR9380)
- UART : pad on PCB (near shielded ath9k chip, white circle)
- assignment : 3.3V, GND, TX, RX from AR8327 side
- settings : 9600n8
- USB : 1x USB 2.0 Type-A
- hub (internal): NEC uPD720114
- Power : 12 VDC, 1.5 A (Max. 17 W)
- Stock OS : NetBSD based
Flash instruction using initramfs-factory.bin image (StockFW WebUI):
1. Boot WR9500N with router mode normally
2. Access to the WebUI ("http://aterm.me/" or "http://192.168.0.1/") on
the device and open firmware update page ("ファームウェア更新")
3. Select the OpenWrt initramfs-factory.bin image and click update
("更新") button
4. After updating, the device will be rebooted and booted with OpenWrt
initramfs image
5. On the initramfs image, upload (or download) uboot.bin and
sysupgrade.bin image to the device
6. Replace the bootloader with a uboot.bin image
mtd write <uboot.bin image> bootloader
7. Perform sysupgrade with a sysupgrade.bin image
sysupgrade <sysupgrade image>
8. Wait ~120 seconds to complete flashing
Flash instruction using initramfs-factory.bin image (bootloader CLI):
1. Connect and open serial console
2. Power on WR9500N and interrupt bootloader by ESC key
3. Login to the bootloader CLI with a password "chiron"
4. Start TFTP server by "tftpd" command
5. Upload initramfs-factory.bin via tftp from your computer
example (Windows): tftp -i 192.168.0.1 PUT initramfs-factory.bin
6. Boot initramfs image by "boot" command
7. On the initramfs image, back up the stock bootloader and firmware if
needed
8. Upload (or download) uboot.bin and sysupgrade.bin image to the device
9. Replace the bootloader with a uboot.bin image
10. Perform sysupgrade with a sysupgrade.bin image
11. Wait ~120 seconds to complete flashing
Notes:
- All LEDs are connected to the GPIO controller on the ath9k chip
(AR9380) and controlled by it. Those LEDs are probed after probing of
ath9k chip, so they cannot be handled as status LEDs of OpenWrt while
booting.
- A reset pin of the internal USB hub is connected to the GPIO
controller of the ath9k chip, like LEDs above. That hub will be
detected after probing of the ath9k chip.
- The stock bootloader requires an unknown filesystem on firmware area
in the flash. Booting of OpenWrt from that filesystem cannot be
handled, so the bootloader needs to be replaced to mainline U-Boot
before OpenWrt installation.
MAC Addresses:
LAN : 1C:B1:7F:xx:xx:60 (config, 0x6 (hex))
WAN : 1C:B1:7F:xx:xx:61 (config, 0xc (hex))
2.4 GHz: 1C:B1:7F:xx:xx:62 (config, 0x0 (hex) / art, 0x1002 (hex))
5 GHz : 1C:B1:7F:xx:xx:63 (config, 0x12 (hex) / art, 0x5002 (hex))
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15432
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
NEC Aterm WR8750N is a 2.4/5 GHz band 11n (Wi-Fi 4) router, based on
AR9344.
Specification:
- SoC : Atheros AR9344
- RAM : DDR2 128 MiB (2x Hynix H5PS5162GFR-S6C)
- Flash : SPI-NOR 8 MiB (Macronix MX25L6406EMI-12G)
- WLAN : 2.4/5 GHz 2T2R
- 2.4 GHz : Atheros AR9344 (SoC)
- 5 GHz : Atheros AR9382
- Ethernet : 5x 10/100/1000 Mbps
- switch : Atheros AR8327
- LEDs/Keys (GPIO): 10x/4x
- note : all LEDs are controlled by ath9k chip (AR9382)
- UART : through-hole on PCB
- assignment : 3.3V, GND, NC, TX, RX from tri-angle marking
- settings : 9600n8
- USB : 1x USB 2.0 Type-A
- hub (internal): NEC uPD720114
- Power : 12 VDC, 1.5 A (Max. 16 W)
- Stock OS : NetBSD based
Flash instruction using initramfs-factory.bin image (StockFW WebUI):
1. Boot WR8750N with router mode normally
2. Access to the WebUI ("http://aterm.me/" or "http://192.168.0.1/") on
the device and open firmware update page ("ファームウェア更新")
3. Select the OpenWrt initramfs-factory.bin image and click update
("更新") button
4. After updating, the device will be rebooted and booted with OpenWrt
initramfs image
5. On the initramfs image, upload (or download) uboot.bin and
sysupgrade.bin image to the device
6. Replace the bootloader with a uboot.bin image
mtd write <uboot.bin image> bootloader
7. Perform sysupgrade with a sysupgrade.bin image
sysupgrade <sysupgrade image>
8. Wait ~120 seconds to complete flashing
Flash instruction using initramfs-factory.bin image (bootloader CLI):
1. Connect and open serial console
2. Power on WR8750N and interrupt bootloader by ESC key
3. Login to the bootloader CLI with a password "chiron"
4. Start TFTP server by "tftpd" command
5. Upload initramfs-factory.bin via tftp from your computer
example (Windows): tftp -i 192.168.0.1 PUT initramfs-factory.bin
6. Boot initramfs image by "boot" command
7. On the initramfs image, back up the stock bootloader and firmware if
needed
8. Upload (or download) uboot.bin and sysupgrade.bin image to the device
9. Replace the bootloader with a uboot.bin image
10. Perform sysupgrade with a sysupgrade.bin image
11. Wait ~120 seconds to complete flashing
Notes:
- All LEDs are connected to the GPIO controller on the ath9k chip
(AR9382) and controlled by it. Those LEDs are probed after probing of
ath9k chip, so they cannot be handled as status LEDs of OpenWrt while
booting.
- A reset pin of the internal USB hub is connected to the GPIO
controller of the ath9k chip, like LEDs above. That hub will be
detected after probing of the ath9k chip.
- The stock bootloader requires an unknown filesystem on firmware area
in the flash. Booting of OpenWrt from that filesystem cannot be
handled, so the bootloader needs to be replaced to mainline U-Boot
before OpenWrt installation.
MAC Addresses:
LAN : 1C:B1:7F:xx:xx:00 (config, 0x6 (hex))
WAN : 1C:B1:7F:xx:xx:01 (config, 0xc (hex))
2.4 GHz: 1C:B1:7F:xx:xx:02 (config, 0x0 (hex) / art, 0x1002 (hex))
5 GHz : 1C:B1:7F:xx:xx:03 (config, 0x12 (hex) / art, 0x5002 (hex))
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15432
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fix PCIe initialization on AR934x by clearing PLL_PWD bit in addition to
PPL(PLL?)_RESET bit of AR724x.
Refresh patches by `make target/linux/refresh`.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15432
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add support for NEC Aterm series devices based on Atheros AR9344.
The following devices have almost the same hardware, so the same U-Boot
binary can be used for them.
- NEC Aterm WR8750N
- NEC Aterm WR9500N
- NEC Aterm WG600HP
By the way, on NetBSD-based NEC Aterm devices, only 0x20000 (128KiB) is
available for a bootloader on the flash chip and that limitation is too
small for mainline U-Boot with the default options. So many
features/commands not required for booting OpenWrt and recoverying are
disabled on that devices, like the followings.
- networking support
- FIT support
- all decompression methods support
etc...
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15432
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add U-Boot package for the devices that based on Atheros/Qualcomm
Atheros SoCs.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15432
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The archs38 now supports 6.6 kernel as testing.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16004
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fix uninitialized variable warnings in function regcache_maple_drop
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16004
Signed-off-by: Robert Marko <robimarko@gmail.com>
Refresh kernel config for Linux 6.6.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16004
Signed-off-by: Robert Marko <robimarko@gmail.com>
This is an automatically generated commit.
When doing `git bisect`, consider `git bisect --skip`.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16004
Signed-off-by: Robert Marko <robimarko@gmail.com>
Update to a more recent stable release.
Most notably, this version includes
some fixes for building on an OS like Alpine.
This allows for the removal of hacks
that fixed building on Alpine,
but broke building on ARM archs.
Manually adjust:
- 7-zip-flags.patch
- 7-zip-musl.patch
Link: https://7-zip.org/history.txt
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Link: https://github.com/openwrt/openwrt/pull/15991
Signed-off-by: Robert Marko <robimarko@gmail.com>
Define the version in one variable,
and use Make functions to use variations of it elsewhere.
Correct the CPE ID.
Override the default tar directory flag
by adding a new value to the tar options
instead of defining the entire command.
Use variables for adjusting build recipes
instead of adding custom build recipes.
Remove unnecessary lines and add spacing.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Link: https://github.com/openwrt/openwrt/pull/15991
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add HOST_MAKE_PATH and use it in order to execute Make
in a subdirectory of the build directory
and in a similar way that MAKE_PATH is used for target building.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Link: https://github.com/openwrt/openwrt/pull/15991
Signed-off-by: Robert Marko <robimarko@gmail.com>
By default nand_do_upgrade() can only deal with raw and gzipped firmware
files. Vendors often use custom firmware containers. Allow passing
custom extraction command to allow using nand_do_upgrade() with vendor
firmwares.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Hardware specification:
SoC: MediaTek MT7986A 4x A53
Flash: ESMT F50L1G41LB 128MB
RAM: MT40A512M16TB-062ER 1GB
Ethernet: 2x 2.5G, 4x 1G Lan
WiFi1: MT7976GN 2.4GHz 4T4R
WiFi2: MT7976AN 5.2GHz 4T4R
WiFi3: MT7915AN 5.8GHz 4T4R
Button: Reset, WPS, Turbo
USB: 1 x USB 3.0
Power: DC 12V 5A
Flash instructions:
1. Execute the following operation to open nc shell:
https://openwrt.org/inbox/toh/tp-link/xdr-6086#rooting
2. Replace the stock bootloader to OpenWrt's:
dd bs=131072 conv=sync of=/dev/mtdblock9 if=/tmp/xxx-preloader.bin
dd bs=131072 conv=sync of=/dev/mtdblock9 seek=28 if=/tmp/xxx-bl31-uboot.fip
3. Connect to your PC via the Gigabit port of the router,
set a static ip on the ethernet interface of your PC.
4. Download the initramfs image, and restart the router,
waiting for tftp recovery to complete.
5. After openwrt boots up, perform sysupgrade.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/15930
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Same as TP-Link TL-XDR608x, this router comes with locked vendor
loader. Add U-Boot build for replacement loader for this device.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/15930
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Ubiquiti has a set of UniFi 802.11ax (Wi-Fi 6) AP devices. All models
include "U6" in their names and also have code names with no special
characters (including spaces).
Examples:
1. U6 Lite (codename U6-Lite)
2. U6 Long-Range (codename U6-LR)
3. U6+ (codename U6-PLUS)
4. U6 Pro (codename U6-Pro)
5. U6 Mesh (codename U6-Mesh)
6. U6 Mesh Pro (codename U6-Mesh-Pro)
7. U6 Enterprise (codename U6-Enterprise)
Use proper full names for those devices. Names in OpenWrt/DTS code may
need updating too but it can be handled later.
Cc: Elbert Mai <code@elbertmai.com>
Cc: Daniel Golle <daniel@makrotopia.org>
Cc: Henrik Riomar <henrik.riomar@gmail.com>
Cc: David Bauer <mail@david-bauer.net>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Radxa ROCK Pi S is a small in size, full in features SBC[1] using the
Rockchip RK3308B SoC.
Hardware
--------
- Rockchip RK3308B SoC
- Quad A35 CPU
- 256/512MB DDR3 RAM
- Optional 4/8GB eMMC
- Micro SD Card slot
- Optional WiFi 4 and BT 4 (not supported yet)
- 1x 100M Ethernet with PoE support (additional PoE HAT required)
- 1x USB 2.0 Type-A port (Host)
- 1x USB 2.0 Type-C port (OTG)
- 2x 26 Pin GPIO header
[1] https://radxa.com/products/rockpi/pis
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/15933
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is required by the DSL CPE API driver.
Signed-off-by: Martin Schiller <ms.3headeddevs@gmail.com>
[update for new license]
Signed-off-by: Andre Heider <a.heider@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15550
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This firmware is used by the vrx518 tc driver.
Signed-off-by: Martin Schiller <ms.3headeddevs@gmail.com>
[update for new license]
Signed-off-by: Andre Heider <a.heider@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15550
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This firmware is used by the vrx518 ep driver.
Signed-off-by: Martin Schiller <ms.3headeddevs@gmail.com>
[update for new license]
Signed-off-by: Andre Heider <a.heider@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15550
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Keenetic KN-3510 is a 2.4/5 Ghz band 11ax access point
Specification:
- System-On-Chip: MT7621AT
- CPU/Speed: 880 MHz
- Flash-Chip: Macronix MX30LF1G28AD-TI
- Flash size: 128 MiB
- RAM: 256 MiB
- 2x 10/100/1000 Mbps Ethernet
- PoE, 802.3af/at
- 4x internal antennas
- UART (J1) header on PCB (115200 8n1)
- WiFi: MT7915 2x2 2.4G 573.5Mbps + 2x2 5G 1201Mbps
- 2x LED, 2x button, 1x mode switch
Notes:
- The device supports dual boot mode
- The firmware partitions were concatinated into one
Flash instruction:
The only way to flash OpenWrt image is to use tftp recovery mode in U-Boot:
1. Configure PC with static IP 192.168.1.2/24 and tftp server.
2. Rename "openwrt-ramips-mt7621-keenetic_kn-3510-squashfs-factory.bin"
to "KN-3510_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
the router and keep button pressed until power led start blinking.
4. Router will download file from server, write it to flash and reboot
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15744
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add the package for the Pixart PAC7302 USB Camera Driver kernel module.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15886
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This device is exactly the same as WL-WN531G3 but with different partition layout and different MAC layout. Labeled as Quantum D4G Rev.: A2.
Hardware
--------
SoC: Mediatek MT7620A
RAM: 64MB
FLASH: 8MB NOR (GigaDevice GD25Q64CS)
ETH:
- 2x 10/100/1000 Mbps Ethernet (RTL8211F)
- 3x 10/100 Mbps Ethernet (integrated in SOC)
WIFI:
- 2.4GHz: 1x (integrated in SOC) (2x2:2)
- 5GHz: 1x MT7612E (2x2:2)
- 4 external antennas
BTN:
- 1x Reset button
- 1x Touchlink button
- 1x Turbo button
- 1x Wps button
- 1x ON/OFF switch
LEDS:
- 1x Red led (system status)
- 1x Blue led (system status)
- 5x Blue leds (ethernet ports)
- 1x Power led
- 1x Wifi led
UART:
- 57600-8-N-1
Everything works correctly.
Installation
------------
Flash the initramfs image in the OEM firmware interface
When Openwrt boots, flash the sysupgrade image otherwise you won't be
able to keep configuration between reboots.
Notes
-----
1) Router mac addresses:
LAN XX:XX:XX:XX:XX:0F (factory @ 0x28)
WAN XX:XX:XX:XX:XX:10 (factory @ 0x2e)
WIFI 2G XX:XX:XX:XX:XX:11 (factory @ 0x04)
WIFI 5G XX:XX:XX:XX:XX:12 (factory @ 0x8004)
LABEL XX:XX:XX:XX:XX:11
Signed-off-by: Eros Brigmann <erosbrigmann@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15876
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In make menuconfig the name is [Amplifi Router HD], and
is missing Ubiquiti. Lets fix that by adding
DEVICE_VENDOR := Ubiquiti to generic-ubnt.mk so the name is:
[Ubiquiti Amplifi Router HD].
Signed-off-by: Kristian Skramstad <kristian+github@83.no>
Link: https://github.com/openwrt/openwrt/pull/15932
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
If we're being paranoid and quote all the arguments to ipcalc.sh,
it's possible to pass in empty start and range arguments. This
should be handled the same as their being absent.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Link: https://github.com/openwrt/openwrt/pull/15946
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Huawei AP6010DN is a dual-band, dual-radio 802.11a/b/g/n 2x2 MIMO
enterprise access point with one Gigabit Ethernet port and PoE
support.
Hardware highlights:
- CPU: AR9344 SoC at 480MHz
- RAM: 128MB DDR2
- Flash: 32MB SPI-NOR
- Wi-Fi 2.4GHz: AR9344-internal radio
- Wi-Fi 5GHz: AR9580 PCIe WLAN SoC
- Ethernet: 10/100/1000 Mbps Ethernet through Atheros AR8035 PHY
- PoE: yes
- Standalone 12V/2A power input
- Serial console externally available through RJ45 port
- External watchdog: CAT706SVI (1.6s timeout)
Serial console:
9600n8 (9600 baud, no stop bits, no parity, 8 data bits)
MAC addresses:
Each device has 32 consecutive MAC addresses allocated by
the vendor, which don't overlap between devices.
This was confirmed with multiple devices with consecutive
serial numbers.
The MAC address range starts with the address on the label.
To be able to distinguish between the interfaces,
the following MAC address scheme is used:
- eth0 = label MAC
- radio0 (Wi-Fi 2.4GHz) = label MAC + 1
- radio1 (Wi-Fi 5GHz) = label MAC + 2
Installation:
0. Connect some sort of RJ45-to-USB adapter to "Console" port of the AP
1. Power up the AP
2. At prompt "Press f or F to stop Auto-Boot in 3 seconds",
do what they say.
Log in with default admin password "admin@huawei.com".
3. Boot the OpenWrt initramfs from TFTP using the hidden script "run ramboot".
Replace IP address as needed:
> setenv serverip 192.168.1.10
> setenv ipaddr 192.168.1.1
> setenv rambootfile openwrt-ath79-generic-huawei_ap6010dn-initramfs-kernel.bin
> saveenv
> run ramboot
4. Optional but recommended as the factory firmware cannot be downloaded publicly:
Back up contents of "firmware" partition using the web interface or ssh:
$ ssh root@192.168.1.1 cat /dev/mtd11 > huawei_ap6010dn_fw_backup.bin
5. Run sysupgrade using sysupgrade image. OpenWrt
shall boot from flash afterwards.
Return to factory firmware (using firmware upgrade package downloaded from non-public Huawei website):
1. Start a TFTP server in the directory where
the firmware upgrade package is located
2. Boot to u-boot as described above
3. Install firmware upgrade package and format the config partitions:
> update system FatAP6X10XN_SOMEVERSION.bin
> format_fs
Return to factory firmware (from previously created backup):
1. Copy over the firmware partition backup to /tmp,
for example using scp
2. Use sysupgrade with force to restore the backup:
sysupgrade -F huawei_ap6010dn_fw_backup.bin
3. Boot AP to U-Boot as described above
Quirks and known issues:
- The stock firmware has a semi dual boot concept where the primary
kernel uses a squashfs as root partition and the secondary kernel uses
an initramfs. This dual boot concept is circumvented on purpose to gain
more flash space and since the stock firmware's flash layout isn't
compatible with mtdsplit.
- The external watchdog's timeout of 1.6s is very hard to satisfy
during bootup. This is why the GPIO15 pin connected to the watchdog input
is configured directly in the LZMA loader to output the AHB_CLK/2 signal
which keeps the watchdog happy until the wdt-gpio kernel driver takes
over. Because it would also take too long to read the whole kernel image
from flash, the uImage header only includes the loader which then reads
the kernel image from flash after GPIO15 is configured.
Signed-off-by: Marco von Rosenberg <marcovr@selfnet.de>
Link: https://github.com/openwrt/openwrt/pull/15941
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hardware specification:
SoC: MediaTek MT7981B 2x A53
Flash: 128 MB SPI-NAND
RAM: 256MB
Ethernet: 4x 10/100/1000 Mbps
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset, Mesh
Power: DC 12V 1A
Gain telnet access:
1. Login into web interface, and download the configuration.
2. Decode and uncompress the configuration:
* Enter fakeroot if you are not login as root.
base64 -d e-xxxxxxxxxxxx-cfg.tar.gz | tar -zx
3. Edit 'etc/passwd', remove root password: 'root::1:0:99999:7:::'.
4. Edit 'etc/rc.local', insert telnetd command before 'exit 0':
( sleep 3s; /usr/sbin/telnetd; ) &
5. Repack the configuration:
tar -zc etc/ | base64 > e-xxxxxxxxxxxx-cfg.tar.gz
6. Upload new configuration via web interface, now you can connect to
ASR3000 via telnet.
Flash instructions:
1. Connect to ASR3000, backup everything, especially 'Factory' part.
2. Write new BL2:
mtd write openwrt-mediatek-filogic-abt_asr3000-preloader.bin BL2
3. Write new FIP:
mtd write openwrt-mediatek-filogic-abt_asr3000-bl31-uboot.fip FIP
4. Set static IP on your PC:
IP 192.168.1.254/24, GW 192.168.1.1
5. Serve OpenWrt initramfs image using TFTP server.
6. Cut off the power and re-engage, wait for TFTP recovery to complete.
7. After OpenWrt has booted, perform sysupgrade.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/15887
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Remove kmod-switch-rtl8366-smi from the package list, as it is still loaded
because kmod-switch-rtl8367b depends on it
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/15757
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit fixes all errors reported by the checkpatch script. This
should make it easier to accept upstream this patch.
There should be no functional changes.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/15939
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch fixes two issues in the driver detach:
* double free of the same descriptor (upstream bug, backported in 66177c081f),
* releasing tx descriptor instead of rx (downstream bug).
The driver is compiled into the kernel that is why the error
is not visible in normal use.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/15939
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch cleans up the following warnings during build:
"warning: format not a string literal"
```
conf.c: In function 'conf_askvalue':
conf.c:89:17: warning: format not a string literal and no format arguments [-Wformat-security]
89 | printf(_("(NEW) "));
| ^~~~~~
conf.c: In function 'conf_choice':
conf.c:285:33: warning: format not a string literal and no format arguments [-Wformat-security]
285 | printf(_(" (NEW)"));
| ^~~~~~
conf.c: In function 'check_conf':
conf.c:440:41: warning: format not a string literal and no format arguments [-Wformat-security]
440 | printf(_("*\n* Restart config...\n*\n"));
| ^~~~~~
conf.c: In function 'main':
conf.c:617:41: warning: format not a string literal and no format arguments [-Wformat-security]
617 | _("\n*** The configuration requires explicit update.\n\n"));
| ^
conf.c:669:25: warning: format not a string literal and no format arguments [-Wformat-security]
669 | fprintf(stderr, _("\n*** Error during writing of the configuration.\n\n"));
| ^~~~~~~
conf.c:673:25: warning: format not a string literal and no format arguments [-Wformat-security]
673 | fprintf(stderr, _("\n*** Error during update of the configuration.\n\n"));
| ^~~~~~~
conf.c:684:25: warning: format not a string literal and no format arguments [-Wformat-security]
684 | fprintf(stderr, _("\n*** Error during writing of the configuration.\n\n"));
| ^~~~~~~
```
And POSIX Yacc warnings
```
lex -ozconf.lex.c -L zconf.l
yacc -ozconf.tab.c -t -l zconf.y
zconf.y:34.1-7: warning: POSIX Yacc does not support %expect [-Wyacc]
34 | %expect 32
| ^~~~~~~
zconf.y:97.1-11: warning: POSIX Yacc does not support %destructor [-Wyacc]
97 | %destructor {
| ^~~~~~~~~~~
gcc -Wall -Wmissing-prototypes -Wstrict-prototypes -O2 -fomit-frame-pointer -DKBUILD_NO_NLS -c -o zconf.tab.o zconf.tab.c
gcc conf.o zconf.tab.o -o conf
```
After:
gcc -Wall -Wmissing-prototypes -Wstrict-prototypes -O2 -fomit-frame-pointer -DKBUILD_NO_NLS -c -o conf.o conf.c
yacc -Wno-yacc -ozconf.tab.c -t -l zconf.y
gcc -Wall -Wmissing-prototypes -Wstrict-prototypes -O2 -fomit-frame-pointer -DKBUILD_NO_NLS -c -o zconf.tab.o zconf.tab.c
gcc conf.o zconf.tab.o -o conf
Signed-off-by: Sean Khan <datapronix@protonmail.com>
Link: https://github.com/openwrt/openwrt/pull/15953
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
NAND code uses either "cat" or "zcat" for getting firmware image
content. Code was full of duplicated ${gz}cat calls. Use "cmd" variable
that is determined by a caller and passed to lower level functions. This
avoids code duplication and allows adding support for more formats.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
