It supports flashing OpenWrt images (bootfs & UBI upgrade) as well as
vendor images (whole MTD partition write).
Upgrading cferom is unsupported. It requires copying device specific
data (like MAC) to target image before flashing.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This way MTD "bootfs" partition will be always 8+ MiB. This should be
enough for any custom / future firmware to fit its bootfs (e.g. big
kernel) without having to repertition whole flash. That way we can
preserve UBI and its erase counters during sysupgrade.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
JFFS2 bootfs partition in a BCM4908 image usually includes some padding.
For flashing it individually (writing to designed MTD partition) we want
just JFFS2 data.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
It's required for upgrading firmware using single partitions instead of
just blindly writing whole image.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
It's much easier to operate on BCM4908 image data with absolute offset
of each section stored. It doesn't require summing sizes over and over.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The purpose of that dummy file is to make CFE work properly with OpenWrt
bootfs. CFE for some reason ignores JFFS2 files with ino 0.
Rename it to 1-openwrt so:
1. It's consistent with bcm63xx
2. It's OpenWrt specific so sysupgrade can distinguish it from vendor
images
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
e78ea9bd26 Update Nios II libm-test-ulps.
98bb18f52a malloc: Fix a realloc crash with heap tagging [BZ 27468]
fc4ecce85b S390: Also check vector support in memmove ifunc-selector [BZ #27511]
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Now that libcap is in OpenWrt base, we can drop our custom patch to
disable libcap support and have lldpd depend on it instead. This will
allow the monitor process to drop its privileges instead of running as
root, improving security.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Having libcap in OpenWrt base allows us to enable libcap support in
other packages in base.
In lldpd, this would allow the monitor process to drop its privileges
instead of running as root, improving security. It will also allow us to
drop our patch to disable libcap.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
This adds support for accessing bootfs JFFS2 partition in the BCM4908
image. Support includes:
1. Listing files
2. Renaming file (requires unchanged name length)
Above commands are useful for flashing BCM4908 images which by defualt
come with cferom.000 file and require renaming it.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
It's important for modifying / extracting firmware content. cferom is
optional image content at the file beginning.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
1. Don't allow pipe stdin as we need to fseek()
2. Don't alow TTY as it doesn't make sense for binary input
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Netgear uses CHK header which needs to be skipped when validating
BCM4908 image. Detect it directly in the bcm4908img tool. Dealing with
binary structs and endianess is way simpler in C.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Move code parsing existing firmware file to separated function. This
cleans up existing code and allows reusing parsing code for other
commands.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This adds support for the MikroTik RouterBOARD RBD52G-5HacD2HnD-TC
(hAP ac²), a indoor dual band, dual-radio 802.11ac
wireless AP with integrated omnidirectional antennae, USB port and five
10/100/1000 Mbps Ethernet ports.
See https://mikrotik.com/product/hap_ac2 for more info.
Specifications:
- SoC: Qualcomm Atheros IPQ4018
- RAM: 128 MB
- Storage: 16 MB NOR
- Wireless:
· Built-in IPQ4018 (SoC) 802.11b/g/n 2x2:2, 2.5 dBi antennae
· Built-in IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 2.5 dBi antennae
- Ethernet: Built-in IPQ4018 (SoC, QCA8075) , 5x 1000/100/10 port,
passive PoE in
- 1x USB Type A port
Installation:
Boot the initramfs image via TFTP and then flash the sysupgrade
image using "sysupgrade -n"
Signed-off-by: Robert Marko <robimarko@gmail.com>
Now that sdcard.gz image contains everything needed to boot straight
into production image, no longer force booting into recovery image on
first boot by removing the logic which implemented that.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Use update_kernel to refresh all patches, required manual updates to:
610-netfilter_match_bypass_default_checks.patch
611-netfilter_match_bypass_default_table.patch
762-net-bridge-switchdev-Refactor-br_switchdev_fdb_notif.patch
764-net-bridge-switchdev-Send-FDB-notifications-for-host.patch
Run-tested: x86_64
Nothing screamed out but any funny business with linux bridging should
suspect this update first.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
f8899b9 netifd: bridge: set default value for igmp_snoop
327da98 netifd: add possibility to switch off route config
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Airtime policy configuration is extremely useful in multiple BSS scenarios.
Since nowadays most people configure both private and guest networks (at
least), it makes sense to enable it by default, except for the most limited
of the variants.
Size of the hostapd-basic-openssl binary (mipsel 24Kc -O2):
543944 bytes (airtime policy disabled)
548040 bytes (airtime policy enabled)
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Acked-by: Daniel Golle <daniel@makrotopia.org>
Switch the Netgear DTSI for the Realtek target from the OEM partition
naming scheme to accepted OpenWrt naming practices. A quick git grep for
'u-boot-env' e.g. in the OpenWrt tree turns up almost 500 hits whereas
grepping for 'bdinfo' (the OEM equivalent) returns a meagre 14.
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
Since KERNEL_SWAP is only enabled by default for !SMALL_FLASH targets, we need
to check if the current kernel supports swap before trying to configure
zram-swap, as opkg can't check for kernel dependencies.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
The FRITZ!Box 3390 actually contains two SoCs, one Lantiq with a
5GHz WiFi and one AR9342 with a 2.4GHz WiFi. Only the Lantiq
has access to the flash memory, the Atheros runs fully from RAM.
Specifications
--------------
- Lantiq 500 MHz
- 128MiB RAM
- 128MiB NAND
- 256k Flash
- AR9580 5GHz WiFi
- AR9342 560 MHz
- 64MiB RAM
- AR9328 2.4GHz WiFi
Remarks
-------
This commit only adds support for the Lantiq side of things and
prepares the drivers for communication with the Atheros SoC. Thus,
only 5GHz WiFi works by default, the 2.4GHz WiFi will be added via
another target.
Some kernel patches will be required to add support for the Atheros SoC.
Installation
------------
Use the eva_ramboot.py script to boot the initramfs image. Then, transfer
the sysupgrade image to the device and run sysupgrade to flash it to the
NAND.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
Acked-by: Aleksander Jan Bajkowski A.Bajkowski@stud.elka.pw.edu.pl
Signed-off-by: Joachim Cerny <cocktail_yogi@web.de>
Switch to Actual Net Data Rate (ACTNDR) for speed reporting on lantiq VDSL modems
Refer to ITU-T G.997.1 chapter 7.5.2.8
Independent whether retransmission is used or not in a given transmit direction:
- In L0 state, this parameter reports the Net Data Rate (as specified in G.992.3, G.992.5 or G.993.2) at which the bearer channel is operating.
- In L2 state, the parameter contains the Net Data Rate (as specified in G.992.3, G.992.5 or G.993.2) in the previous L0 state.
Signed-off-by: Jeroen Peelaerts <jeroen.peelaerts@gmail.com>
Reviewed-by: Andre Heider <a.heider@gmail.com>
This commit adds monitoring for a couple of DSL line features that are
present in the lantiq firmware blobs.
* G.INP ON/OFF
* Trellis encoding ON/OFF
* Virtaul Noise ON/OFF
* Bitswap ON/OFF
Difference in size for ltq-vdsl-app = 1k
Difference in size for kmod-ltq-vdsl-vr9 < 1k
Reviewed-by: Andre Heider <a.heider@gmail.com>
Signed-off-by: Jeroen Peelaerts <jeroen.peelaerts@gmail.com>
"firmware" partition size defined in the device tree file is 0xf70000,
so the right IMAGE_SIZE is 15808k
Fixes: df1e5d6463 ("ramips: fix partition layout of hiwifi hc5x61")
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Add 5.10 as testing kernel. Builds successfully with
CONFIG_ALL_KMODS=y enabled.
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
This was done by executing these commands:
$ make kernel_oldconfig CONFIG_TARGET=subtarget
$ make kernel_oldconfig CONFIG_TARGET=subtarget_platform
Some common symbols have been moved to target config.
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
This was done by executing these commands:
$ make kernel_oldconfig CONFIG_TARGET=subtarget
$ make kernel_oldconfig CONFIG_TARGET=subtarget_platform
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
If service() is called w/o parameter then the status display for services
with multiple instances is incorrect. E.g. samba4 or wpad have 2 instances.
root@OpenWrt:~# /etc/init.d/samba4 status
running
root@OpenWrt:~# /etc/init.d/wpad status
running
Before change:
/etc/init.d/samba4 enabled stopped
/etc/init.d/wpad enabled stopped
After change:
/etc/init.d/samba4 enabled running
/etc/init.d/wpad enabled running
Signed-off-by: Alexander Egorenkov <egorenar-dev@posteo.net>
Upstream iproute2 detects libbpf using a one-line $CC test-compile, which
normally ignores LDFLAGS. With NLS enabled however, LDFLAGS includes an
"rpath-link" linker option needed to resolve libintl.so. Its absence
causes both the compile and libbpf detection to fail:
ld: warning: libintl.so.8, needed by libbpf.so, not found (try using
-rpath or -rpath-link)
ld: libelf.so.1: undefined reference to `libintl_dgettext'
collect2: error: ld returned 1 exit status
Fix this by directly including $LDFLAGS in the test-compile command.
Reported-by: Ian Cooper <iancooper@hotmail.com>
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
