FCC ID: A8J-EPG600
Engenius EPG600 is an indoor wireless router with
1 Gb ethernet switch, dual-band wireless,
internal antenna plates, USB, and phone lines (not supported)
this board is a Senao device:
the hardware is equivalent to EnGenius ESR600 (except for phone lines)
the software is Senao SDK which is based on openwrt and uboot
which uses the legacy Senao header with Vendor / Product IDs
to verify the firmware upgrade image.
**Specification:**
- MT7620 SOC MIPS 24kec, 2.4 GHz WMAC, 2x2
- RT5592N WLAN PCI chip, 5 GHz, 2x2
- QCA8337N Gb SW RGMII GbE, SW P0 -- SOC P5, 5 LEDs
- 40 MHz clock
- 16 MB FLASH MX25L12845EMI-10G
- 64 MB RAM NT5TU32M16
- UART console J2, populated
- USB 2.0 port direct to SOC
- 6 GPIO LEDs power, 2G, 5G, wps2g, wps5g, line
- 3 buttons reset, wps, "reg" (registeration)
- 4 antennas internal omni-directional plates
NOT YET SUPPORTED: VoIP
- Si3050-FT + Si3019-FT Voice DAA, SPI control, PCM data
- Phone Ports "TEL", "LINE" RJ11, 4P2C (2 pins)
**MAC addresses:**
MAC address labeled as MAC ADDRESS
MACs present in both wifi cal data and uboot environment
eth0.1/phy1 ---- *:82 rf 0x4
phy0 ---- *:83 factory 0x4
eth0.2 MAC *:b8 "wanaddr"
**Installation:**
Method 1: Firmware upgrade page:
(if you cannot access the APs webpage)
factory reset with the reset button
connect ethernet to a computer
OEM webpage at 192.168.0.1
username and password 'admin'
Navigate to gear icon, "Device Management", "Tools"
select the factory.dlf image
Upload and verify checksum
Method 2: Serial to upload initramfs:
Follow directions for TFTP recovery
upload and boot initramfs and do a sysupgrade
**TFTP recovery:**
Requires UART serial console, reset button does nothing
rename initramfs-kernel.bin to 'uImageEPG600'
make available on TFTP server at 192.168.99.8
power board, interrupt boot with "4"
execute `tftpboot` and `bootm` (with the load address)
**Return to OEM:**
Images from OEM are provided, but not compatible
with openwrt sysupgrade. So it must be modified.
Alternatively, back up all mtd partitions before flashing
**Note on switch registers:**
The necessary registers needed for the QCA8337 switch
can be read from interrupted boot (tftpboot, bootm)
by using the following lines in the switch driver ar8327.c
in the function 'ar8327_hw_config_of'
where 'qca,ar8327-initvals' is parsed from DTS
before the new register values are written:
pr_info("0x04 %08x\n", ar8xxx_read(priv, AR8327_REG_PAD0_MODE));
pr_info("0x08 %08x\n", ar8xxx_read(priv, AR8327_REG_PAD5_MODE));
pr_info("0x0c %08x\n", ar8xxx_read(priv, AR8327_REG_PAD6_MODE));
pr_info("0x10 %08x\n", ar8xxx_read(priv, AR8327_REG_POWER_ON_STRAP));
Signed-off-by: Michael Pratt <mcpratt@pm.me>
General specification:
- SoC Type: MediaTek MT7620N (580MHz)
- ROM: 8 MB SPI-NOR (W25Q64FV)
- RAM: 64 MB DDR (M13S5121632A)
- Switch: MediaTek MT7530
- Ethernet: 5 ports - 5×100MbE (WAN, LAN1-4)
- Wireless 2.4 GHz: b/g/n
- Buttons: 1 button (RESET)
- Bootloader: U-Boot 1.1.3, MediaTek U-Boot: 5.0.0.5
- Power: 12 VDC, 1.0 A
Flash by the native uploader in 2 stages:
1. Use the native uploader to flash an initramfs image. Choose
openwrt-ramips-mt7620-snr_cpe-w4n-mt-initramfs-kernel.bin file by
"Administration/Management/Firmware update/Choose File" in vendor's
web interface (ip: 192.168.1.10, login: Admin, password: Admin).
Wait ~160 seconds.
2. Flash a sysupgrade image via the initramfs image. Choose
openwrt-ramips-mt7620-snr_cpe-w4n-mt-squashfs-sysupgrade.bin
file by "System/Backup/Flash Firmware/Flash image..." in
LuCI web interface (ip: 192.168.1.1, login: root, no password).
Wait ~240 seconds.
Flash by U-Boot TFTP method:
1. Configure your PC with IP 192.168.1.131
2. Set up TFTP server and put the
openwrt-ramips-mt7620-snr_cpe-w4n-mt-squashfs-sysupgrade.bin
image on your PC
3. Connect serial port (57600 8N1) and turn on the router.
Then interrupt "U-Boot Boot Menu" by hitting 2 key (select "2:
Load system code then write to Flash via TFTP.").
Press Y key when show "Warning!! Erase Linux in Flash then burn
new one. Are you sure? (Y/N)"
Input device IP (192.168.1.1) ==:192.168.1.1
Input server IP (192.168.1.131) ==:192.168.1.131
Input Linux Kernel filename () ==:
openwrt-ramips-mt7620-snr_cpe-w4n-mt-squashfs-sysupgrade.bin
3. Wait ~120 seconds to complete flashing
Signed-off-by: Alexey Bartenev <41exey@proton.me>
This device is almost identical to the already supported Edimax
EW-7476RP5, the only differences are:
- There is no mode selection slider switch on this device
- The two wireless LEDs are green instead of blue
- Model name in the CSYS header is RN10
Additional changes:
- Moved WiFi LEDs and the slider switch to the individual dt files
- Added ieee80211-freq-limit to the mt7612e radio to properly disable
2.4GHz band on this radio
Device specifications:
SoC: MediaTek MT7620a @ 580MHz
RAM: 64M (Winbond W9751G6KB-25)
FLASH: 8MB (Macronix)
WiFi: SoC-integrated: MediaTek MT7620a bgn
WiFi: MediaTek MT7612EN nac
GbE: 1x (RTL8211E)
BTN: WPS/RESET
LED: - WiFi 5G (green)
- WiFi 2.4G (green)
- Signal Strength (green)
- Power (green)
- WPS (green)
- LAN (green)
UART: UART is present as Pads with throughholes on the PCB. They are
located next to the WPS button
3.3V - RX - GND - TX / 57600-8N1
3.3V is the square pad
Installation:
Upload the sysupgrade image via the default web interface
Signed-off-by: Daniel Fuchs <software@sagacioussuricata.com>
This patch adds support for Netcore NW5212, provided by some carrier in
China.
Specifications:
--------------
* SoC: Mediatek MT7620A
* RAM: 128MB DDR2
* Flash: 16MB SPI NOR flash (Winbond W25Q128BV)
* WiFi 2.4GHz: builtin
* Ethernet: builtin
* LED: Power, WAN, LAN 1-4, WiFi
* Buttons: Reset (GPIO 13)
* UART: Serial console (57600 8n1)
* USB: 1 x USB2
Installation:
------------
The router comes with OpenWrt 14.07 built with MTK SDK. However, as the
modem is provided by carriers, so the web interface is highly minimized and
only contains a static page with no interaction options.
There are two possible ways to gain the access.
1) Open the shell and use a UART2USB convert to gain TTY access. Please
notice you have to remove resistance R54 at the back of the board
otherwise you won't be able to input anything.
2) Use built-in backdoor. Access http://192.168.1.1/cgi-bin/_/testxst to
start dropbear service at port 9122. Be warned the software is super
old and only diffie-hellman-group1-sha1, diffie-hellman-group14-sha1,
kexguess2@matt.ucc.asn.au is support, you may not be able to connect it
with an up-to-date ssh client.
After you can control the device, flash the firmware as usual. Here are
some hints for that.
Option 1 (via original firmware):
1) Setup HTTP server on your computer, for example:
python3 -m http.server
2) Connect to the route and flash:
cd /tmp
wget http://<your-computer-host>/<your-firmware-name>
mtd -r write <your-firmware-name> firmware
Option 2 (replacing u-boot via breed):
1) Download breed-mt7620-reset13.bin from https://breed.hackpascal.net/
2) Setup HTTP server on your computer, for example:
python3 -m http.server
You can skip this step if your breed is already accessible from HTTP,
since the original wget does not support HTTPS.
3) Connect to the route and flash breed:
cd /tmp
wget http://<your-computer-host>/breed-mt7620-reset13.bin
mtd write breed-mt7620-reset13.bin Bootloader
4) Reboot. Hold reset key or press any key in TTY to enter breed.
5) Access breed web interface (http://192.168.1.1/). Choose the flash
layout to be 0x50000 and flash new firmware.
MAC addresses:
-------------
There are three MACs stored in factory, as in MT7620A reference design:
source address usage
0x4 label WLAN
0x28 label MAC 1
0x2e label + 1 MAC 2
However, the OEM firmware only uses one single MAC (label) for all
interfaces, probably a misconfiguration.
Signed-off-by: David Yang <mmyangfl@gmail.com>
This patch adds support for Netgear PR2000, sold as "Travel Router and
Range Extender".
Specifications:
--------------
* SoC: Mediatek MT7620N
* RAM: 64MB DDR2
* Flash: 16MB SPI NOR flash (Macronix MX25L12805D)
* WiFi 2.4GHz: builtin
* Ethernet: builtin
* LED: Power, Internet, WiFi, USB
* Buttons: Reset (GPIO 1/2)
* UART: Serial console (57600 8n1)
* USB: 1 x USB2
SPECIAL NOTES:
-------------
Problem: WiFi is super weak, but SSID beacons seems to be right.
Solve: Change 36h in factory partition (namely 0xf60036) to be 0x0.
Explain: Clearly Netgear have different ideas on how EEPROM is used. Bit 2
of 36h indicates the presence of External LNA for 11g (2.4 GHz) band,
which seems to be incorrectly set by Netgear (originally 0x04). Lifting it
solves the problem of weak RX signal.
Installation:
------------
There are two possible ways to install the firmware. Flashing via web
interface of original firmware is not tested due to a broken firmware.
1) Open the shell and use a UART2USB convert to gain TTY access (TP7: RXD,
TP9: TXD, TP10: GND). Please notice you have to remove resistance R54
next to TP7 otherwise you won't be able to input anything.
2) Use well-known Netgear debug switch. Access
http://192.168.168.1/setup.cgi?todo=debug to start telnet service
(username: root, password: <none>).
Please back up firmware if you want to go back to the original.
After you can control the device, flash the firmware as usual. Here are
some hints for that.
Option 1 (via nmrpflash):
1) Download nmrpflash from https://github.com/jclehner/nmrpflash
2) Use *-factory.img and flash:
nmrpflash -L
nmrpflash -i net* -f <your-firmware-name>
3) Turn off then turn on the device, wait it finishing flash.
Option 2 (replacing u-boot via breed):
1) Download breed-mt7620-reset1.bin from https://breed.hackpascal.net/
2) Setup HTTP server on your computer, for example:
python3 -m http.server
You can skip this step if your breed is already accessible from HTTP,
since the original wget does not support HTTPS.
3) Connect to the route and flash breed:
cd /tmp
wget http://<your-computer-host>/breed-mt7620-reset1.bin
dd if=breed-mt7620-reset1.bin of=/dev/mtdblock0 bs=64k
4) Reboot. Hold reset key or press any key in TTY to enter breed.
5) Access breed web interface (http://192.168.1.1/). Choose memory layout
to be 0x40000 and flash new firmware.
Remark:
------
As a "Range Extender", it has a switch to switch between Wired mode (GPIO
21 low) and Wireless mode (GPIO 20 low), which is not implemented in this
patch. However, the router will be turned off when it switches to the
middle, which makes this switch much less useful.
MAC addresses:
-------------
The OEM firmware uses one single MAC for all interfaces, located at
0xf700b0.
Signed-off-by: David Yang <mmyangfl@gmail.com>
For HiWiFi series devices, label_mac can be read from bdinfo partition,
and lan_mac, wlan2g_mac are same as the label_mac. Converting label_mac
to wlan5g_mac only needs to unset 6th bit. (It seems that all HiWiFi's
label_mac start with D4:EE)
For example:
label D4:EE:07:32:84:88
lan D4:EE:07:32:84:88
wan D4:EE:07:32:84:89
wlan2g D4:EE:07:32:84:88
wlan5g D0:EE:07:32:84:88
Tested on HiWiFi HC5661.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
This patch adds support for the Netgear WN3100RPv2
http://www.netgear.com/support/product/wn3100rpv2.aspx
Specifications:
- SoC: MediaTek MT7620A (580MHz, ramips)
- RAM: 32MB DDR
- Storage: 8MB NOR SPI flash
- Wireless: builtin MT7620A, 2x2:2 with u.FL connectors
- Ethernet: 1x100M
- Stock firmware based on OpenWRT Kamikaze
Like the EX2700, the bootloader expects a secondary image signature,
see https://forum.openwrt.org/viewtopic.php?pid=312577#p312577
This device seems to be same hardware as a WN3000RPv3
Flash instructions:
- Use the Netgear WebUI to upgrade to OpenWRT using the factory image
(see note below),
- Use the sysupgrade image for upgrading versions from OpenWRT,
- TFTP recovery procedure can be used to flash the factory image
(preferred method).
Note:
- The WebUI may not reboot automatically, wait at least 5 minutes before
powercycling the device
Flashing using TFTP:
- Set you IP address to 192.168.1.10/24 (no gateway)
- Connect your machine to the Ethernet port
- Power off the device and wait for 10 seconds,
- Hold the reset button and power on the device (do not release reset),
- Hold the reset button until the green light is flashing (Approx. 15s)
- launch tftp, set mode to binary and connect to 192.168.1.1
- put the factory firmware image
- All leds will switch off (like a power off), this is normal
- Wait for the device to reboot in the new OpenWRT image (max 5 mins)
- The first boot will take longer than usual.
- After boot, the Device IP on the ethernet port is 192.168.1.1
Signed-off-by: Rodolphe de Saint Léger <rdesaintleger@gmail.com>
[drop unneeded includes in dts, wrap commit message]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
This reverts commit 7bc20cb614.
It adds support for Netgear WN3100RPv2, but the commit title is wrong.
It will be re-added with the correct title.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
This patch adds support for the Netgear WN3100RPv2
http://www.netgear.com/support/product/wn3100rpv2.aspx
Specifications:
- SoC: MediaTek MT7620A (580MHz, ramips)
- RAM: 32MB DDR
- Storage: 8MB NOR SPI flash
- Wireless: builtin MT7620A, 2x2:2 with u.FL connectors
- Ethernet: 1x100M
- Stock firmware based on OpenWRT Kamikaze
Like the EX2700, the bootloader expects a secondary image signature,
see https://forum.openwrt.org/viewtopic.php?pid=312577#p312577
This device seems to be same hardware as a WN3000RPv3
Flash instructions:
- Use the Netgear WebUI to upgrade to OpenWRT using the factory image
(see note below),
- Use the sysupgrade image for upgrading versions from OpenWRT,
- TFTP recovery procedure can be used to flash the factory image
(preferred method).
Note:
- The WebUI may not reboot automatically, wait at least 5 minutes before
powercycling the device
Flashing using TFTP:
- Set you IP address to 192.168.1.10/24 (no gateway)
- Connect your machine to the Ethernet port
- Power off the device and wait for 10 seconds,
- Hold the reset button and power on the device (do not release reset),
- Hold the reset button until the green light is flashing (Approx. 15s)
- launch tftp, set mode to binary and connect to 192.168.1.1
- put the factory firmware image
- All leds will switch off (like a power off), this is normal
- Wait for the device to reboot in the new OpenWRT image (max 5 mins)
- The first boot will take longer than usual.
- After boot, the Device IP on the ethernet port is 192.168.1.1
Signed-off-by: Rodolphe de Saint Léger <rdesaintleger@gmail.com>
[drop unneeded includes in dts, wrap commit message]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
The DWR-961 A1 Wireless Router is based on the MT7620A SoC.
It's a merge of two Amit boards: DWR-960 with ethernet part
of Lava LR-25G001.
ROMID it's taken from Telenor branded version and it works with tested
device. Images from D-Link site for this router are from DWR-953 and it
have ROMID DLK6E2424001. I don't know if it's mistake on web-site
or if it's will require different image.
Specification:
- MediaTek MT7620A (580 Mhz)
- 128 MB of RAM
- 16 MB of FLASH
- 1x 802.11bgn radio
- 1x 802.11ac radio (MT7612 mpcie card)
- 5x 10/100/1000 Mbps Ethernet: 4xLAN and 1xWAN (QCA8337)
- 2x internal, non-detachable antennas (Wifi 2.4G)
- 3x external, detachable antennas (2x LTE, 1x Wifi 5G)
- 1x LTE modem cat 6
- UART (J5) header on PCB (57600 8n1)
- 13x LED, 2x button
- JBOOT bootloader
Installation:
Apply factory image via http web-gui or JBOOT recovery page
How to revert to OEM firmware:
- push the reset button and turn on the power. Wait until LED start
blinking (~10sec.)
- upload original factory image via JBOOT http (IP: 192.168.123.254)
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
The Wavlink WL-WN535K1 is a "mesh" router with 2 gigabit ethernet ports
and one fast ethernet port. Mine is branded as Talius TAL-WMESH1.
It can be found in kits of 2 or 3 (WL-WN535K2 or WL-WN535K3).
The motherboard is labelled as WS-WN535G3-B-V1.2 so this image could
potentially work for WL-WN535G3R and WS-WN535G3R with little to none
effort, but it's untested.
Hardware
--------
SoC: Mediatek MT7620A
RAM: 64MB
FLASH: 8MB NOR (GigaDevice GD25Q64CS)
ETH:
- 2x 10/100/1000 Mbps Ethernet (RTL8211F)
- 1x 10/100 Mbps Ethernet (integrated in SOC)
WIFI:
- 2.4GHz: 1x (integrated in SOC) (2x2:2)
- 5GHz: 1x MT7612E (2x2:2)
- 4 internal antennas
BTN:
- 1x Reset button
- 1x Touchlink button (set to WPS)
- 1x ON/OFF switch
LEDS:
- 1x Red led (system status)
- 1x Blue led (system status)
- 3x Green leds (ethernet port status/act)
UART:
- 57600-8-N-1
Everything works correctly.
Currently there is no firmware update available. Because of this, in
order to restore the OEM firmware, you must firstly dump the OEM
firmware from your router before you flash the OpenWrt image.
Backup the OEM Firmware
-----------------------
The following steps are to be intended for users having little to none
experience in linux. Obviously there are many ways to backup the OEM
firmware, but probably this is the easiest way for this router.
Procedure tested on WN535K1_V1510_200916 firmware version.
1) Go to http://192.168.10.1/webcmd.shtml
2) Type the following line in the "Command" input box and then press enter:
mkdir /etc_ro/lighttpd/www/dev; dd if=/dev/mtd0ro of=/etc_ro/lighttpd/www/dev/mtd0ro
3) After few seconds in the textarea should appear this output:
16384+0 records in
16384+0 records out
If your output doesn't match mine, stop reading and ask for
help in the forum.
4) Open in another tab http://192.168.10.1/dev/mtd0ro to download the
content of the whole NOR. If the file size is 0 byte, stop reading
and ask for help in the forum.
5) Come back to the http://192.168.10.1/webcmd.shtml webpage and type:
rm /etc_ro/lighttpd/www/dev/mtd0ro;for i in 1 2 3 4 5; do dd if=/dev/mtd${i}ro of=/etc_ro/lighttpd/www/dev/mtd${i}ro; done
6) After few seconds, in the textarea should appear this output:
384+0 records in
384+0 records out
128+0 records in
128+0 records out
128+0 records in
128+0 records out
14720+0 records in
14720+0 records out
1024+0 records in
1024+0 records out
If your output doesn't match mine, stop reading and ask for
help in the forum.
7) Open the following links to download the partitions of the OEM FW:
http://192.168.10.1/dev/mtd1rohttp://192.168.10.1/dev/mtd2rohttp://192.168.10.1/dev/mtd3rohttp://192.168.10.1/dev/mtd4rohttp://192.168.10.1/dev/mtd5ro
If one (or more) of these files are 0 byte, stop reading and ask
for help in the forum.
8) Store these downloaded files in a safe place.
9) Reboot your router to remove any temporary file in ram.
Installation
------------
Flash the initramfs image in the OEM firmware interface
(http://192.168.10.1/update_mesh.shtml).
When Openwrt boots, flash the sysupgrade image otherwise you won't be
able to keep configuration between reboots.
Restore OEM Firmware
--------------------
Flash the "mtd4ro" file you previously backed-up directly from LUCI.
Warning: Remember to not keep settings!
Warning2: Remember to force the flash.
Notes
-----
1) Router mac addresses:
LAN XX:XX:XX:XX:XX:E2 (factory @ 0x28)
WAN XX:XX:XX:XX:XX:E3 (factory @ 0x2e)
WIFI 2G XX:XX:XX:XX:XX:E4 (factory @ 0x04)
WIFI 5G XX:XX:XX:XX:XX:E5 (factory @ 0x8004)
LABEL XX:XX:XX:XX:XX:E5
2) The OEM firmware upgrade page accepts only files containing the
string "WN535K1" in the filename.
3) Additional notes 1,2,3 in the WS-WN583A6 commit are still valid
(92780d80ab)
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
[remove trailing whitespace]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
HUMAX E2 (also known as HUMAX QUANTUM E2) is a 2.4/5GHz band AC router,
based on MediaTek MT7620A.
Specifications:
- SoC: MT7620A
- RAM: DDR2 64MB
- Flash: SPI NOR 8MB (MXIC MX25L6405D)
- WiFi:
- 2.4GHz: SoC internal
- 5GHz: MT7610E
- Ethernet: 1x 10/100Mbps
- Switch: SoC internal
- UART: J2 (57600 8N1)
- pinout: [3V3] (RXD) (GND) (TXD)
Installation and Recovery via TFTP:
1. Connect ethernet cable between Router port and PC Ethernet port.
2. Set your computer to a static IP **192.168.1.1**
3. Turn the device off and wait a few seconds. Hold the WPS button on front
of device and insert power.
4. Send a firmware image to **192.168.1.6** using TFTP.
You can use any TFTP client. (tftp, curl, Tftpd64...)
5. Wait until Power LED stop flashing. **DO NOT TURN OFF DEVICE!**
The device will be automatically rebooted.
Signed-off-by: Kyoungkyu Park <choryu.park@choryu.space>
WeVO AIR DUO is a 1-bay NAS & 802.11ac (Wi-Fi 5) router, based on
MediaTek MT7620A.
Specifications:
* SoC: MT7620A
* RAM: 64 MiB
* Flash: SPI NOR 16 MiB
* USB & SATA bridge controller: JMicron JMS567
* SATA 6Gb/s: 2.5" drive slot
* USB 3.0: Micro-B
* USB 2.0: connected to SoC
* Wi-Fi:
* 2.4 GHz: SoC built-in
* 5 GHz: MT7612EN
* Ethernet: 5x 1GbE
* Switch: MT7530WU
* UART: 4-pin 1.27 mm pitch through-hole (57600 baud)
* Pinout: (3V3)|(RXD) (TXD) (GND)
Notes:
* The drive is accessible through the external USB port only when the
router is turned off.
Installation via web interface:
1. Flash **initramfs** image through the stock web interface.
The image filename should have ".upload" extension.
2. Boot into OpenWrt and perform sysupgrade with sysupgrade image.
Revert to stock firmware:
1. Perform sysupgrade with stock image.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
In 20b09a2125 Lava LR-25G001 router have problem with two inactive
ethernet ports. JBOOT bootloader didn't configure ethernet devices by default.
The same situation was there. It is required to enable all phy ports.
This is fragment of stock bootlog:
switch reg write_athr offset=90, value=2b0
switch reg write_athr offset=8c, value=2b0
switch reg write_athr offset=88, value=2b0
switch reg write_athr offset=84, value=2b0
switch reg write_athr offset=80, value=2b0
This patch adds proper registers configuration ar8337 initvals.
0x2b0 value causes force flow control configuration, 0x1200 was used
instead (flow control config auto-neg with phy). [1]
When switch is now ok, let's fix port numeration too.
Fixes: 20b09a2125 ("ramips: add support for Lava LR-25G001")
[1] https://github.com/openwrt/openwrt/pull/4806#issuecomment-982019858
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
LED labels for this device are different in 01_leds file and in device
DTS. Switch to DT triggers, which works on Telewell TW-4 (LTE) clone
device.
This has not been tested on the LR-25G001 itself, just on the clone
mentioned above.
Fixes: 20b09a2125 ("ramips: add support for Lava LR-25G001")
Signed-off-by: Jani Partanen <rtfm@iki.fi>
[rephrase commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Sitecom WLR-4100 v1 002 (marked as X4 N300) is a wireless router
Specification:
SoC: MT7620A
RAM: 64 MB DDR2
Flash: MX25L6405D SPI NOR 8 MB
WIFI: 2.4 GHz integrated
Ethernet: 5x 10/100/1000 Mbps QCA8337
USB: 1x 2.0
LEDS: 2x GPIO controlled, 5x switch
Buttons: 1x GPIO controlled
UART: row of 4 unpopulated holes near USB port, starting count from
white triangle on PCB:
VCC 3.3V
GND
TX
RX
baud: 115200, parity: none, flow control: none
Installation
Connect to one of LAN (yellow) ethernet ports,
Open router configuration interface,
Go to Toolbox > Firmware,
Browse for OpenWrt factory image with dlf extension and hit Apply,
Wait few minutes, after the Power LED will stop blinking, the router is
ready for configuration.
Known issues
Some USB 2.0 devices work at full speed mode 1.1 only
MAC addresses
factory partition only contains one (binary) MAC address in 0x4.
u-boot-env contains four (ascii) MAC addresses, of which two appear
to be valid.
factory 0x4 **:**:**:**:b9:84 binary
u-boot-env ethaddr **:**:**:**:b9:84 ascii
u-boot-env wanaddr **:**:**:**:b9:85 ascii
u-boot-env wlanaddr 00:AA:BB:CC:DD:12 ascii
u-boot-env iNICaddr 00:AA:BB:CC:DD:22 ascii
The factory firmware only assigns ethaddr. Thus, we take the
binary value which we can use directly in DTS.
Additional information
OEM firmware shell password is: SitecomSenao
useful for creating backup of original firmware.
There is also another revision of this device (v1 001), based on RT3352 SoC
Signed-off-by: Andrea Poletti <polex73@yahoo.it>
[remove config DT label, convert to nvmem, remove MAC address
setup from u-boot-env, add MAC address info to commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Give users more control by exposing ephy leds.
Signed-off-by: David Yang <mmyangfl@gmail.com>
[remove execute bit on 01_leds, add status for gpio2]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Specifications:
* SOC: MT7620A + MT7610E
* ROM: 16 MiB spi flash (W25Q128FVSG)
* RAM: 128 MiB DDR2 (W971GG6KB-25)
* WAN: 10/100M *1
* LAN: 10/100M *4
* USB: Type-A USB2.0 *1
* SD: MicroSD *1
* Button: Reset *1
* Antennas: 2.4 GHz *2 + 5 GHz *1
* TTL Baudrate: 57600
* U-Boot Recovery: IP: 10.10.10.123, Server: 10.10.10.3
Installation:
* Web UI Update
1. Open http://192.168.10.1/upgrade.html in the browser.
2. Rename firmware to a short name like firmware.bin and then upload it.
3. Fill in the password column with the following content:
password | mtd -x mIp2osnRG3qZGdIlQPh1 -r write /tmp/firmware.bin firmware
* TFTP + U-Boot
1. Connect device with a TTL cable.
2. Press "2" when booting to select "Load system code then write to Flash via TFTP".
3. Upload firmware by tftpd64, it will boot when write instruction is executed.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Descriptions：
Phicomm K2 (PSG1218) got a new "permanent_config" partition after
update firmware to v22.5. This partition located in front of the
firmware partition, same as The Phicomm K2P and K2G. Due to this
change the new bootloader can't load previous firmware any more.
This commit is aimed at add support for Phicomm K2 which official
firmware version is 22.5.x or newer. For which runs old firmware
version, just update OpenWrt that has a prefix of "k2-v22.4".
For uniform naming, this commit also changed the model name
PSG1218 to a more recognizable name K2, refer to Phicomm K2G,
K2P K2T.
OpenWrt selection table:
official firmware version OpenWrt
v22.4.x.x or older phicomm_k2-v22.4
v22.5.x.x or newer phicomm_k2-v22.5
Installation:
Same as Phicomm K2G, K2P, PSG1208.
a. TFTP + U-Boot
b. Open telnet by some web page vulnerability (Search Baidu by key
words "K2 telnet"), and then we can upload firmware image to
/tmp and write it to firmware partition with mtd instruction.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[rebase, add/harmonize version in model variables, fix version typo
in commit message, wrap commit message properly]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
These boards have AR8327 or QCA8337 external ethernet switch.
The SOC also has it's own internal switch
where VLAN is now enabled by default.
Changes to preinit caused all switches to have VLANs enabled by default
even if they are not configured with a topology in uci_defaults
(see commit f017f617ae)
When both internal and external switches have VLANs,
and the external switch has both LAN and WAN,
the TX traffic from the SOC cannot flow to the tagged port on the external switch
because the VLAN IDs are not matching.
So disable the internal switch VLANs by default on these boards.
Also, add a topology for the internal switch,
so that on LuCI there is not an "unknown topology" warning.
In theory, it may be possible to have LAN ports on both switches
through internal and external PHYs, but there are no known boards that have this.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
About the device
----------------
SoC: MediaTek MT7620a @ 580MHz
RAM: 64M
FLASH: 8MB
WiFi: SoC-integrated: MediaTek MT7620a bgn
WiFi: MediaTek MT7612EN nac
GbE: 2x (RTL8211F)
BTN: - WPS
- Reset
- Router/Repeater/AP (3-way slide-switch)
LED: - WPS (blue)
- 3-segment Wifi signal representation (blue)
- WiFi (blue)
- WAN (blue)
- LAN (blue)
- Power (blue)
UART: UART is present as Pads with through-holes on the PCB. They are
located next to the reset button and are labelled Vcc/TX/RX/GND as
appropriate. Use 3.3V, 57600-8N1.
Installation
------------
Using the webcmd interface
--------------------------
Warning: Do not update to the latest Wavlink firmware (version
20201201) as this removes the webcmd console and you will need to
use the serial port instead.
You will need to have built uboot/sqauashfs image for this device,
and you will need to provide an HTTP service where the image can
be downloaded from that is accessible by the device.
You cannot use the device manufacturers firmware upgrade interface
as it rejects the OpenWrt image.
1. Log into the device's admin portal. This is necessary to
authenticate you as a user in order to be able to access the
webcmd interface.
2. Navigate to http://<device-ip>/webcmd.shtml - you can access
the console directly through this page, or you may wish to
launch the installed `telnetd` and use telnet instead.
* Using telnet is recommended since it provides a more
convenient shell interface that the web form.
* Launch telnetd from the form with the command `telnetd`.
* Check the port that telnetd is running on using
`netstat -antp|grep telnetd`, it is likely to be 2323.
* Connect to the target using `telnet`. The username should
be `admin2860`, and the password is your admin password.
3. On the target use `curl` to download the image.
e.g. `curl -L -O http://<some-other-lan-ip>/openwrt-ramips-mt7620-\
wavlink_wl-wn579x3-squashfs-sysupgrade.bin`.
Check the hash using `md5sum`.
4. Use the mtd_write command to flash the image.
* The flash partition should be mtd4, but check
/sys/class/mtd/mtd4/name first. The partition should be
called 'Kernel'.
* To flash use the following command:
`mtd_write -r -e /dev/mtd<n> write <image-file> /dev/mtd<n>`
Where mtd<n> is the Kernel partition, and <image-file> is
the OpenWrt image previously downloaded.
* The command above will erase, flash and then reboot the
device. Once it reboots it will be running OpenWrt.
Connect via ssh to the device at 192.168.1.1 on the LAN port.
The WAN port will be configured via DHCP.
Using the serial port
---------------------
The device uses uboot like many other MT7260a based boards. To
use this interface, you will need to connect to the serial
interface, and provide a TFTP server. At boot follow the
bootloader menu and select option 2 to erase/flash the image.
Provide the address and filename details for the tftp server.
The bootloader will do the rest.
Once the image is flashed, the board will boot into OpenWrt. The
console is available over the serial port.
Signed-off-by: Ben Gainey <ba.gainey@googlemail.com>
Device specifications:
* Model: Youku YK-L1/L1c
* CPU: MT7620A
* RAM: 128 MiB
* Flash: 32 MiB (YK-L1)/ 16 MiB (YK-L1c)
* LAN: 2* 10M/100M Ports
* WAN: 1* 10M/100M Port
* USB: 1* USB2.0
* SD: 1* MicroSD socket
* UART: 1* TTL, Baudrate 57600
Descriptions:
Previous supported device YOUKU yk1 is actually Youku YK-L1. Though they look
really different, the only hardware difference between the two models is flash
size, YK-L1 has 32 MiB flash but YK-L1c has 16MiB. It seems that YK-L1c can
compatible with YK-L1's firmware but it's better to split it to different models.
It is easy to identify the models by looking at the label on the bottom of the
device. The label has the model number "YK-L1" or "YK-L1c". Due to different flash
sizes, YK-L1c that using previous YK-L1's firmware needs to apply "force update"
to install compatible firmware, so please backup config file before system upgrade.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[use more specific name for DTSI]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
MAC addresses read from official firmware
value location
Wlan xx 71 de factory@0x04
Lan xx 71 dd factory@0x28
Wan xx 71 df factory@0x2e
Label xx 71 dd factory@0x28
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[fix sorting in 02_network, redact commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
1. rename led pin "air" to a more common name "wlan" and use "phy0tpt" to trigger it.
2. led "wan" can be triggered by ethernet pinctrl by default so just drop it.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
There are only two lan ports and one wan port on Youku yk1
Fixes: e9baf8265b ("ramips: add support for Youku YK1")
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[add Fixes:]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
So far, board.d files were having execute bit set and contained a
shebang. However, they are just sourced in board_detect, with an
apparantly unnecessary check for execute permission beforehand.
Replace this check by one for existance and make the board.d files
"normal" files, as would be expected in /etc anyway.
Note:
This removes an apparantly unused '#!/bin/sh /etc/rc.common' in
target/linux/bcm47xx/base-files/etc/board.d/01_network
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The lan port sequence was reversed compared to the labels.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[improve commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Phicomm K2G:
add missing label_mac
Phicomm PSG1218A & PSG1218B:
The previous wan mac was set as factory@0x28 +1 (originally based
on the default case for the ramips target), but the correct wan mac
is factory@0x28 -1, being equal to factory@0x2e.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[minor commit title/message adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Same hardware as Phicomm K2G but different flash layout.
Specification:
- SoC: MediaTek MT7620A
- Flash: 8 MB
- RAM: 64 MB
- Ethernet: 4 FE ports and 1 GE port (RTL8211F on port 5)
- Wireless radio: MT7620 for 2.4G and MT7612E for 5G, both equipped
with external PA.
- UART: 1 x UART on PCB - 57600 8N1
Flash instruction:
To avoid requiring UART for TFTP a dual flash procedure is suggested
to install the squashfs image:
1. Rename openwrt-ramips-mt7620-wavlink_wl-wn530hg4-initramfs-kernel.bin
to WN530HG4-WAVLINK.
2. Flash this file with the factory web interface.
3. With OpenWRT now running use standard sysupgrade to install the
squashfs image.
Signed-off-by: Nuno Goncalves <nunojpg@gmail.com>
[remove dts-v1, remove model from LED labels, wrap commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
While we mostly use the ucidef_set_led_* functions directly in 01_leds
we still have the set_wifi_led function in parallel for several old
devices. This is not only inconsistent with the other definitions,
it also links to the wlan0 interface instead of using a phy trigger
which would be independent of the interface name (and is used for
all newer devices anyway). Apart from that, the standard names
"wifi" and "wifi-led" are not very helpful in a world with different
radio bands either.
Thus, this patch removes the set_wifi_led function and puts the
relevant commands into the cases explicitly. This makes the
mechanism used more evident and will hopefully lead to some future
improvements or at least prevent some copy-pasting of the old
setups.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
In ramips, it's not common to use an alias for specifying the WiFi
LED; actually only one device uses this mechanism (TL-WR841N v14).
Particularly since the WiFi LEDs are typically distinguished between
2.4G and 5G etc. it is also not very useful for this target.
Thus, this patch removes the setup lines for this mechanism and
converts the TL-WR841N v14 to the normal setup.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Like in the previous patch for ath79 target, this will remove the
"devicename" from LED labels in ramips as well.
The devicename is removed in DTS files and 01_leds, consolidation
of definitions into DTSI files is done where (easily) possible,
and migration scripts are updated.
For the latter, all existing definitions were actually just
devicename migrations anyway. Therefore, those are removed and
a common migration file is created in target base-files. This is
actually another example of how the devicename removal makes things
easier.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
According to the User Manual, there is a "Wi-Fi LED" with blue and
green colors, doing the following by default:
Flashing Blue: System loading
Solid Blue: System loaded
Flashing Green: Connecting to the Internet
Solid Green: Connected to the Internet
According to this vendor behavior, we keep refer to the LED as "wifi"
but implement the according default behavior as in OEM firmware.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The RAVPower RP-WD03 is a battery powered router, with an Ethernet and
USB port. Due due a limitation in the vendor supplied U-Boot bootloader,
we cannot exceed a 1.5 MB kernel size, as is the case with recent builds
(i.e. post v19.07). This breaks both factory and sysupgrade images.
To address this, use the lzma loader (loader-okli) to work around this
limitation.
The improvements here also address the "misplaced" U-Boot environment
partition, which is located between the kernel and rootfs in the stock
image / implementation. This is addressed by making use of mtd-concat,
maximizing space available in the booted image.
This will make sysupgrade from earlier versions impossible.
Changes are based on the recently supported HooToo HT-TM05, as the
hardware is almost identical (except for RAM size) and is from the same
vendor (SunValley). While at it, also change the SPI frequency
accordingly.
Installation:
- Download the needed OpenWrt install files, place them in the root
of a clean TFTP server running on your computer. Rename the files as,
- openwrt-ramips-mt7620-ravpower_rp-wd03-squashfs-kernel.bin => kernel
- openwrt-ramips-mt7620-ravpower_rp-wd03-squashfs-rootfs.bin => rootfs
- Plug the router into your computer via Ethernet
- Set your computer to use 10.10.10.254 as its IP address
- With your router shut down, hold down the power button until the first
white LED lights up.
- Push and hold the reset button and release the power button. Continue
holding the reset button for 30 seconds or until it begins searching
for files on your TFTP server, whichever comes first.
- The router (10.10.10.128) will look for your computer at 10.10.10.254
and install the two files. Once it has finished installation, it will
automatically reboot and start up OpenWrt.
- Set your computer to use DHCP for its IP address
Notes:
- U-Boot environment can be modified, u-boot-env is preserved on initial
install or sysupgrade
- mtd-concat functionality is included, to leave a "hole" for u-boot-env,
combining the OEM kernel and rootfs partitions
Most of the changes in this commit are the work of Russell Morris (as
credited below), I only wrapped them up and added compat-version.
Thanks to @mpratt14 and @xabolcs for their help getting the lzma loader
to work!
Fixes: 5ef79af4f8 ("ramips: add support for Ravpower WD03")
Suggested-by: Russell Morris <rmorris@rkmorris.us>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The HooToo HT-TM05 is a battery powered router, with an Ethernet and USB port.
Vendor U-Boot limited to 1.5 MB kernel size, so use lzma loader (loader-okli).
Specifications:
SOC: MediaTek MT7620N
BATTERY: 10400mAh
WLAN: 802.11bgn
LAN: 1x 10/100 Mbps Ethernet
USB: 1x USB 2.0 (Type-A)
RAM: 64 MB
FLASH: GigaDevice GD25Q64, Serial 8 MB Flash, clocked at 50 MHz
Flash itself specified to 80 MHz, but speed limited by mt7620 SPI
fast-read enabled (m25p)
LED: Status LED (blue after boot, green with WiFi traffic
4 leds to indicate power level of the battery (unable to control)
INPUT: Power, reset button
MAC assignment based on vendor firmware:
2.4 GHz *:b4 (factory 0x04)
LAN/label *:b4 (factory 0x28)
WAN *:b5 (factory 0x2e)
Tested and working:
- Ethernet
- 2.4 GHz WiFi (Correct MAC-address)
- Installation from TFTP (recovery)
- OpenWRT sysupgrade (Preserving and non-preserving), through the usual
ways: command line and LuCI
- LEDs (except as noted above)
- Button (reset)
- I2C, which is needed for reading battery charge status and level
- U-Boot environment / variables (from U-Boot, and OpenWrt)
Installation:
- Download the needed OpenWrt install files, place them in the root
of a clean TFTP server running on your computer. Rename the files as,
- ramips-mt7620-hootoo_tm05-squashfs-kernel.bin => kernel
- ramips-mt7620-hootoo_tm05-squashfs-rootfs.bin => rootfs
- Plug the router into your computer via Ethernet
- Set your computer to use 10.10.10.254 as its IP address
- With your router shut down, hold down the power button until the first
white LED lights up.
- Push and hold the reset button and release the power button. Continue
holding the reset button for 30 seconds or until it begins searching
for files on your TFTP server, whichever comes first.
- The router (10.10.10.128) will look for your computer at 10.10.10.254
and install the two files. Once it has finished installation, it will
automatically reboot and start up OpenWrt.
- Set your computer to use DHCP for its IP address
Notes:
- U-Boot environment can be modified, u-boot-env is preserved on initial
install or sysupgrade
- mtd-concat functionality is included, to leave a "hole" for u-boot-env,
combining the OEM kernel and rootfs partitions
I would like to thank @mpratt14 and @xabolcs for their help getting the
lzma loader to work!
Signed-off-by: Russell Morris <rmorris@rkmorris.us>
[drop changes in image/Makefile, fix indent and PKG_RELEASE in
uboot-envtools, fix LOADER_FLASH_OFFS, minor commit message facelift,
add COMPILE to Device/Default]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Specification:
- CPU: MediaTek MT7620N (580 MHz)
- Flash size: 4 MB NOR SPI
- RAM size: 32 MB DDR1
- Bootloader: U-Boot
- Wireless: MT7620N 2x2 MIMO 802.11b/g/n (2.4 GHz)
- Switch: MT7620 built-in 10/100 switch with vlan support
- Ports: 4x LAN, 1x WAN
- Others: 7x LED, Reset button, UART header on PCB (57600 8N1)
Flash instructions:
1. Use ethernet cable to connect router with PC/Laptop, any router
LAN port will work.
2. To flash openwrt we are using nmrpflash[1].
3. Flash commands:
First we need to identify the correct Ethernet id.
nmrpflash -L
nmrpflash -i net* -f openwrt-ramips-mt7620-netgear_jwnr2010-v5-squashfs-factory.img
This will show something like "Advertising NMRP server on net*..." (net*, *=1,2,3... etc.)
4. Now remove the power cable from router back side and immediately connect it again.
You will see flash notification in CMD window, once it says reboot the device just
plug off the router and plug in again.
Revert to stock:
1. Download the stock firmware from official netgear support[2].
2. Follow the same nmrpflash procedure like above, this time just use the stock firmware.
nmrpflash -i net* -f N300-V1.1.0.54_1.0.1.img
MAC addresses on stock firmware:
LAN = *:28 (label)
WAN = *:29
WLAN = *:28
On flash, the only valid MAC address is found in factory 0x4.
Special Note:
This openwrt firmware will also support other netgear N300 routers like below as they
share same stock firmware[3].
JNR1010v2 / WNR614 / WNR618 / JWNR2000v5 / WNR2020 / WNR1000v4 / WNR2020v2 / WNR2050
[1] https://github.com/jclehner/nmrpflash
[2] https://www.netgear.com/support/product/JWNR2010v5.aspx
[3] http://kb.netgear.com/000059663
Signed-off-by: Shibajee Roy <ador250@protonmail.com>
[create DTSI, use netgear_sercomm_nor, disable by default, add MAC
addresses to commit message, add label MAC address]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This drops the shebang from all target files for /lib and
/etc/uci-defaults folders, as these are sourced and the shebang
is useless.
While at it, fix the executable flag on a few of these files.
This does not touch ar71xx, as this target is just used for
backporting now and applying cosmetic changes would just complicate
things.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This updates the display port order for the TEW-810DR to be in line
with the DIR-810L. Both share the same board and pictures on the
vendors' pages indicate the same external numbering scheme as well.
Signed-off-by: J. Scott Heppler <shep971@centurylink.net>
[replace commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The port order displayed in LuCI is currently inverted for this
devices:
LuCI - Device
LAN1 - LAN4
LAN2 - LAN3
LAN3 - LAN2
LAN4 - LAN1
Fix it.
Strangely, the owner of a TRENDnet TEW-810DR reports that the
initial port order is correct, while both devices share the
same board and look similar from the outside. Since I cannot
investigate this without having any of the devices, this does
only touch the DIR-810L for now.
While at it, also merge in the case for zbtlink,zbt-we2026, as
the display port specified for WAN there won't have any effect
anyway.
Reported-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The WAN LED on DIR-810L was actually blinking on LAN1 port
activity. This has already been improved for the TEW-810DR, where
the GPIO has been set up explicitly rather than having it controlled
by the switch.
This patch also applies this setup to the DIR-810L.
In addition, the trigger in 01_leds is set up with
ucidef_set_led_switch for both devices now, so state changes should
be displayed correctly as well.
Reported-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net> [DIR-810L]
Tested-by: J. Scott Heppler <shep971@centurylink.net> [TEW-810DR]
Specifications:
* SoC: MT7620A
* CPU: 580 MHz
* RAM: 64 MB DDR
* Flash: 8MB NOR SPI flash
* WiFi: MT7612E (5GHz) and builtin MT7620A (2.4GHz)
* LAN: 1x100M
The device is identical to the EX6130 except
for the mains socket and the hardware ID.
Installation:
The -factory images can be flashed from the
device's web interface or via nmrpflash.
Notes:
MAC addresses were set up based on the EX6130 setup.
This is based on prior work of Adam Serbinski and Mathias Buchwald.
Tested by Mathias Buchwald.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Specifications:
* MediaTek MT7620A (580 Mhz)
* 8 MB of FLASH
* 64 MB of RAM
* 2.4Ghz and 5.0Ghz radios
* 5x 10/100 Mbps Ethernet (1 WAN and 4 LAN)
* UART header on PCB (57600 8n1)
* Green/Orange Power LEDs illuminating a Power-Button Lens
* Green/Orange Internet LEDs GPIO controlled illuminating a Globe/Internet Lens
* 3x button - wps, power and reset
* U-boot bootloader
Installation:
The sysupgrade.bin image is reported to be OEM web flashed with an ncc_att_hwid
appended. ncc_att_hwid is a 32bit binary in the GPL Source download for either
the TEW-810DR or DIR-810L and is located at
source/user/wolf/cameo/ncc/hostTools.
The invocation is: ncc_att_hwid -f tew-810dr-squashfs-factory.bin -a -m "TEW-810DR" -H "1.0R" -r "WW" -c "1.0"
This may need to be altered if your hardware version is "1.1R".
The image can also be directly flashed via serial tftp:
1. Load *.sysupgrade.bin to your tftp server directory and rename for
convenience.
2. Set a static ip 192.168.10.100.
3. NIC cable to a lan port.
4. Serial connection parameters 57600,8N1
5. Power on the TEW-810 and press 4 for a u-boot command line prompt.
6. Verify IP's with U-Boot command "printenv".
7. Adjust tftp settings if needed per the tftp documentation
8. Boot the tftp image to test the build.
9. If the image loads, reset your server ip to 192.168.1.10 and restart network.
10. Log in to Luci, 192.168.1.1, and flash the *sysupgrade.bin image.
Notes:
The only valid MAC address is found in 0x28 of the factory partition.
Other typical offsets/caldata only contain example data: 00:11:22:00:0f:xx
Signed-off-by: J. Scott Heppler <shep971@centurylink.net>
[remove "link rx tx" in 01_leds, format and extend commit message,
fix DTS led node names]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
ramips images now relies on explicit switch setup for proper failsafe
functionality. Remove default cases where it relies on vlan setup in
dts and add switch setup for devices affected.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
The location 0x28 in factory partition is the common one used for
ethernet address on this architecture. Despite, it contains the label
MAC address for the devices at hand.
Consequently, this patch moves 0x28 to the ðernet node in DTS files
(setting the WAN MAC address there) and sets up the lan_mac from 0x22
in 02_network. As a benefit, this allows to use label-mac-device in
DTS instead of ucidef_set_label_macaddr.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Like for the RT-AC54U, this uses a DT trigger for WiFi also at the
RT-AC51U. While at it, rename node and label to wifi2g.
Note that the 5g WiFi LED still isn't supported (see PR #3017 for
further details: https://github.com/openwrt/openwrt/pull/3017 )
Tested-by: Davide Fioravanti <pantanastyle@gmail.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The current MAC address assignment for the ASUS RT-AC51U is "wrong",
it actually should be the same as for the RT-AC54U. Fix it.
MAC assignment based on vendor firmware:
2g 0x4 label
5g 0x8004 label +4
lan 0x22 label +4
wan 0x28 label
Thanks to Davide Fioravanti for checking this on his device.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
netis WF2770 is a 2.4/5GHz band AC750 router, based on MediaTek MT7620A.
Specifications:
- SoC: MT7620A
- RAM: DDR2 64MB
- Flash: SPI NOR 16MB
- WiFi:
- 2.4GHz: SoC internal
- 5GHz: MT7610EN
- Ethernet: 5x 10/100/1000Mbps
- Switch: MT7530BU
- UART:
- J2: 3.3V, RX, TX, GND (3.3V is the square pad) / 57600 8N1
MAC addresses in factory partition:
0x0004: LAN, WiFi 2.4GHz (label_mac-6)
0x0028: not used (label_mac-1)
0x002e: WAN (label_mac)
0x8004: WiFi 5GHz (label_mac+2)
Installation via web interface:
1. Flash **initramfs** image through the stock web interface.
2. Boot into OpenWrt and perform sysupgrade with sysupgrade image.
Revert to stock firmware:
1. Perform sysupgrade with stock image.
Reviewed-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
