TP-Link RE350K v1 (FCC ID: TE7RE350K) is a wall-plug AC1200 Wi-Fi range
extender with 'Kasa Smart' support. Device is based on Qualcomm/Atheros
QCA9558 + QCA9882 + AR8035 platform and is available only on US market.
Specification:
- 720/600/200 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of flash (SPI NOR)
- 1x 1 Gbps Ethernet (AR8035)
- 2T2R 2.4 GHz (QCA9558), with ext. PA (SE2565T) and LNA (SKY65971-11)
- 2T2R 5 GHz (QCA9882), with ext. PA (SE5003L1-R) and LNA (SKY65981-11)
- 2x U.FL connector on PCB
- 2x dual-band PCB antennas
- 1x LED, 2x dual-color LED (all driven by GPIO)
- 3x button (app config, led, reset)
- 1x mechanical on/off slide switch
- 1x UART (4-pin, 2.54 mm pitch) header on PCB
- 1x JTAG (8-pin, 1.27 mm pitch) header on PCB
Flash instruction:
Use 'factory' image directly in vendor GUI (default IP: 192.168.0.254,
default credentials: admin/admin).
Warning:
This device does not include any kind of recovery mechanism in U-Boot.
Vendor firmware access:
You can access vendor firmware over serial (RX line requires jumper
resistor in R306 place, near XTAL) with: root/sohoadmin credentials.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
ALFA Network Tube-E4G is an outdoor, dual-SIM LTE Cat. 4 CPE, based on
MediaTek MT7620A, equipped with Quectel EC25 miniPCIe modem.
Specification:
- MT7620A (580 MHz)
- 64/128/256 MB of RAM (DDR2)
- 16/32 MB of flash (SPI NOR)
- 1x 10/100 Mbps Ethernet, with passive PoE support (24 V)
- 1x miniPCIe slot (with PCIe and USB 2.0 buses)
- 2x SIM slot (mini, micro) with detect and switch driven by GPIO
- 1x detachable antenna (modem main)
- 1x internal antenna (modem div)
- 1x GPS passive antenna (optional)
- 5x LED (all driven by GPIO)
- 1x button (reset)
- UART (4-pin, 2.54 mm pitch) header on PCB
Other:
Default SIM slot is selected at an early stage by U-Boot, based on
'default_sim' environment value: 1 or unset = SIM1 (mini), 2 = SIM2
(micro). U-Boot also resets the modem, using #PERST signal, before
starting kernel.
Flash instruction:
You can use the 'sysupgrade' image directly in vendor firmware which is
based on OpenWrt (make sure to not preserve settings - use 'sysupgrade
-n -F ...' command). Alternatively, use web recovery mode in U-Boot:
1. Power the device with reset button pressed, the LAN LED will start
blinking slowly and after ~3 seconds, when it starts blinking faster,
you can release the button.
2. Setup static IP 192.168.1.2/24 on your PC.
3. Go to 192.168.1.1 in browser and upload 'sysupgrade' image.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This disables PL010 and 8250 serial support for this platform
as both drivers are not used: the debug UART is PL011 and the
application UARTs use a dedicated MXS specific driver.
The kernel size reduction is neglectable, but it also removes
the non-working (confusing) /dev/ttyS0 and /dev/ttyS1 devices
in a running system (which generate errors when trying to use):
root@OpenWrt:~# echo "hello world" > /dev/ttyS0
ash: write error: I/O error
root@OpenWrt:~#
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Add missing /usr/sbin install dir fixing :
install: cannot create regular file 'build_dir/target-x86_64_musl/busybox-1.30.1/.pkgdir/busybox/usr/sbin/ntpd-hotplug': No such file or directory
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Move PCIe controller outside down to SoC level to avoid resource
mapping problems.
Also add more detailed error handling when mapping registers.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
cfb47d30 Take into account larger frame size for prioritization
dbbe4e01 Remove unused field
371bc3a8 clang-format
5e7889c5 Update manual pages
b1b2ad50 Bump up version number to 1.37.0, LT revision to 31:2:17
e043ca83 Update AUTHORS
c2434dfb Simplify stream_less
816ad210 Reuse name when indexing header by referencing dynamic table
f5feb16e Merge pull request #1295 from bratkartoffel/fix-compile-boringssl
adf09f21 Merge pull request #1303 from donny-dont/fix-shared-install
2591960e Explicitly set install location when building shared libs
d93842db nghttpx: Fix backend stall if header and request body are sent in 2 packets
8dc2b263 nghttpx: Use std::priority_queue
8d842701 Update manual pages
de85b0fd Update README
5d6beed5 Merge branch 'nghttpx-backend-weight'
1ff9de4c nghttpx: Backend address selection with weight
34482ed4 Fix compilation with boringssl
9b6ced66 Bump up version number to 1.37.0-DEV
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
This fixes the following compile problem with kernel 4.20:
In file included from arp.c:20:0:
include/linux/if_arp.h:121:16: error: 'IFNAMSIZ' undeclared here (not in a function)
char arp_dev[IFNAMSIZ];
^~~~~~~~
make[7]: *** [Makefile:459: arp.o] Error 1
This is caused by commit 6a12709da354 ("net: if_arp: use define instead
of hard-coded value") in the upstream Linux kernel which is integrated
in Linux 4.20.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
They should be relative to apb-bridge@47000000 rather than to the
pcie-controller@c00000 inside it.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Traverse LS1043 boards are set up with a dual-system layout, rootfs{1,2} and kernel{1,2}.
nand_do_upgrade can do the image replacement work we were doing before as long as we give it the partition names.
This greatly simplifies the /lib/upgrade/platform.sh.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Upcoming product specification and branding changes mean that the names in tree do not accurately reflect released products.
To reduce any confusion, sort our boards by SoC family, e.g traverse-ls1043. Any future boards using Layerscape family SoC's
will be treated the same way, e.g Device/traverse-ls/lx/laXXXX.
The affected boards so far have only been available through OEM channels and those aren't using the provided sysupgrade.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
The configure script broke when used in alpine-3.9 based docker containers. Fixed in wolfSSL >3.15.7.
Signed-off-by: Moritz Warning <moritzwarning@web.de>
Require the word "warning" to appear at the start of a line, after
whitespace, or after a `:`. This is the same that CTest launchers use
to match warnings. It avoids matching "warning" inside file paths.
Fixed in cmake 3.14.0.
Signed-off-by: Moritz Warning <moritzwarning@web.de>
This patch re-enables the reset_ppe() functionality for VR9 targets by using
the new lantiq rcu subsystem. The reset sequence in the reset_ppe() function
was taken from the ppa datapath driver of lantiq UGW 7.4.1.
Additionally it adds the required reset definitions to the vr9 dtsi file.
It also prepares the reset_ppe() function calls for the other lantiq targets.
This feature is needed to be able to switch between ltq-atm/ltq-ptm driver
in ATM/PTM Auto-Mode at runtime.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Hardware:
- SoC: Lantiq VRX288
- RAM: Winbond W971GG6JB 1 Gb (128 MiB)
- Flash:
- SPI: 8 Mb (1 MiB) for bootloader and tffs
- NAND: 1 Gb (128 MiB) for OS
- xDSL: Lantiq VRX208
- WLAN: Atheros AR9381
- DECT: Dialog Semiconductors SC14441
Everything except FXS/DECT works
(no drivers for AVM's FXS implementation with SC14441).
Installation via FTP:
1. Use scripts/flashing/eva_ramboot.py to send initramfs-kernel.bin
to the device when powering on.
Standard AVM procedures with finding the correct IP address and
the right moment to open FTP apply here (approx. 4 seconds on 7362SL).
IMPORTANT: set lzma compression in ramdisk options, bootloader stalls
when receiving uncompressed images.
2. Transfer sysupgrade.bin image with scp to /tmp directory
and run sysupgrade
3. First boot might take a bit longer if linux_fs_start was set to 1,
in that case the device will reboot twice, first time it will fail to load
second kernel (overwritten by ubifs), set linux_fs_start to 0 and reboot.
OpenWrt uses the entire NAND flash. Kernel uses 4 MiB and rootfs uses
the rest of 124 MiB, overwriting everything related to FRITZ!OS - both
OS images, config and answering machine/media server data.
To return to FRITZ!OS, use AVM's recovery image.
Signed-off-by: Danijel Tudek <danijel.tudek@gmail.com>
Hardware:
SoC: Lantiq VRX 220
CPU Cores: 2x MIPS 34Kc at 500 MHz
RAM: 128 MiB 250 MHz
Storage: 128 MiB NAND flash
Ethernet: built-in Fast Ethernet switch, only port 2 is used
Wireless: Atheros AR9287-BL1A b/g/n with 2 pcb antennas
Modem: built-in A/VDSL2 modem
DECT: Dialog SC14441
LEDs: 1 two-color, 4 one-color
Buttons: 2
FXS: 1 port via TAE or RJ12 connector
Everything except FXS/DECT works
(no drivers for AVM's FXS implementation with SC14441).
Installation:
Use the eva_ramboot.py script to load an initramfs image on the
device. Run it a few seconds after turning the device on.
$ scripts/flashing eva_ramboot 192.168.178.1 bin/targets/lantiq/xrx200/openwrt-lantiq-xrx200-avm_fritz7412-initramfs-kernel.bin
If it fails to find the device try the ip address 169.254.120.1.
(Firmware updates or the recovery tool apparently change it.)
IMPORTANT: set lzma compression in ramdisk options, bootloader stalls
when receiving uncompressed images.
The device will load it in ram and boot it. You can reach it under
the openwrt default ip address 192.168.1.1.
Check if the key linux_fs_start is not set to 1 in tffs:
$ fritz_tffs_nand -d /dev/mtd1 -n linux_fs_start
If it is set to 1, the bootloader will select the wrong set of
partitions. Restart the box and install an FritzOS upgrade or do a
recovery. Afterwards start again at step 1.
Run sysupgrade to persistently install OpenWRT.
Signed-off-by: Valentin Spreckels <Valentin.Spreckels@Informatik.Uni-Oldenburg.de>
Signed-off-by: Andy Binder <AndyBinder@gmx.de>
A tool for reading the TFFS partitions (a name-value storage usually
found in AVM Fritz!Box based devices) on nand flash.
Copyright (c) 2018 Valentin Spreckels <Valentin.Spreckels@Informatik.Uni-Oldenburg.DE>
Based on the fritz_tffs_read tool:
Copyright (c) 2015-2016 Martin Blumenstingl <martin.blumenstingl@googlemail.com>
and on the TFFS 2.0 kernel driver from AVM:
Copyright (c) 2004-2007 AVM GmbH <fritzbox_info@avm.de>
and the TFFS 3.0 kernel driver from AVM:
Copyright (C) 2004-2014 AVM GmbH <fritzbox_info@avm.de>
and the OpenWrt TFFS kernel driver:
Copyright (c) 2013 John Crispin <blogic@openwrt.org>
This program is free software; you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation; either version 2 of the License, or
(at your option) any later version.
This program is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
You should have received a copy of the GNU General Public License along
with this program; if not, write to the Free Software Foundation, Inc.,
51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA.
Signed-off-by: Valentin Spreckels <Valentin.Spreckels@Informatik.Uni-Oldenburg.de>
Signed-off-by: Andy Binder <AndyBinder@gmx.de>
The patches to the /dev/crypto engine were commited to openssl master,
and will be in the next major version (3.0).
Changes:
- Optimization in computing a digest in one operation, saving an ioctl
- Runtime configuration options for the choice of algorithms to use
- Command to dump useful information about the algorithms supported by
the engine and the system.
- Build the devcrypto engine as a dynamic module, like other engines.
The devcrypto engine is built as a separate package by default, but
options were added to allow building the engines into the main library.
Signed-off-by: Eneas U de Queiroz <cote2004-github@yahoo.com>
[refresh patches]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
YunCore A770 is a ceiling AC750 AP with 2 Fast Ethernet ports, PoE
(802.3at) support, based on QCA9531 + QCA9887.
Specification:
- 650/597/216 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of flash (SPI NOR)
- 2x 10/100 Mbps Ethernet (PoE 802.3at support in WAN port)
- 2T2R 2.4 GHz (QCA9531), with ext. PA and LNA
- 1T1R 5 GHz (QCA9887), with ext. FEM (SKY85728-11)
- 2x regular LED, 1x RGB LED (all driven by GPIO)
- 1x button (reset)
- DC jack for main power input (12 V)
- UART header on PCB
Flash instruction:
1. First, gain root access to the device, following below steps:
- Login into web gui (default password/IP: admin/192.168.188.253).
- Go to 'Advanced' -> 'Management' -> 'System' and download backup of
configuration (bakfile.bin).
- Open the file as tar.gz archive, edit/update 'shadow' file and change
hash of root password to something known.
- Repack the archive, rename it back to 'bakfile.bin' and use to
restore configuration of the device.
- After that, device will reboot and can be accessed over SSH.
2. Then, install OpenWrt:
- Login over SSH and issue command:
fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000"
- Upload 'sysupgrade' image and install it (only if previous command
succeeded) with command: 'sysupgrade -n -F openwrt-...'.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Backport below changes for I2C QUP driver from v4.17:
0668bc44a426 i2c: qup: fix copyrights and update to SPDX identifier
7239872fb340 i2c: qup: fixed releasing dma without flush operation completion
eb422b539c1f i2c: qup: minor code reorganization for use_dma
6d5f37f166bb i2c: qup: remove redundant variables for BAM SG count
c5adc0fa63a9 i2c: qup: schedule EOT and FLUSH tags at the end of transfer
7e6c35fe602d i2c: qup: fix the transfer length for BAM RX EOT FLUSH tags
3f450d3eea14 i2c: qup: proper error handling for i2c error in BAM mode
08f15963bc75 i2c: qup: use the complete transfer length to choose DMA mode
ecb6e1e5f435 i2c: qup: change completion timeout according to transfer length
6f2f0f6465ac i2c: qup: fix buffer overflow for multiple msg of maximum xfer len
f7714b4e451b i2c: qup: send NACK for last read sub transfers
fbfab1ab0658 i2c: qup: reorganization of driver code to remove polling for qup v1
7545c7dba169 i2c: qup: reorganization of driver code to remove polling for qup v2
This fixes various I2C issues observed on AP120C-AC board equipped with
Atmel/Microchip AT97SC3205T TPM module.
Tested-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Use 'ath10k-calibration-variant' (with the value sent upstream) for the
second (5 GHz) radio in AP120C-AC board DTS. First radio uses the same
BDF as in one of Qualcomm reference designs.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Add specific 'variant' for 'bus=ahb,bmi-chip-id=0,bmi-board-id=25' BDF.
Use the same value ('ALFA-Network-AP120C-AC') as sent upstream.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This is useful in for the attendedsyupsgrade server (asu) to
distinguish between snapshot version. Currently asu can't tell devices
requesting a snapshot build if the same build is already installed.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Instead of showing a slightly more readable target like
"ar71xx (Generic)" print the more generic format "ar71xx/genric"
Signed-off-by: Paul Spooren <mail@aparcar.org>
1d7760d mt76: mt7603: set moredata flag when queueing ps-filtered packets
0b927b2 mt76: fix return value check in mt76_wmac_probe()
e72376d mt76x02: fix hdr pointer in write txwi for USB
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fixes timeouts with trying to access the FTP site.
Also remove mirror2.openwrt.org, which does not keep current tarballs
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This patch fixes a crash that occured on the
BT Home Hub v5a (lantiq/xrx200) which resulted
in the device bootlooping.
Reported-by: Ryan Mounce <ryan@mounce.com.au>
Tested-by: Vitalij Alshevsky <v_alshevsky@tut.by>
Fixes: ddece08bf4 ("kernel: owl-loader: fix sparse endian warnings")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
dts: disable port4 and leave it ephy mode because it connect to nothing
switch port5 connected to GE port we use it as wan port
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
fixes intermittent loss of connectivity on 1Gbit port, with
log message:
803x_aneg_done: SGMII link is not ok
Signed-off-by: Mantas Pucka <mantas@8devices.com>
This backports upstream commit
34d5629 ath10k: limit available channels via DT ieee80211-freq-limit
to the 4.19 ath10k-ct version. Without this patch, disabled channels
are still listed as a supported configuration for the radio.
The identical patch was also backported by OpenWRT to the non-ct driver.
It can be dropped as soon as we switch to an ath10k-ct version based on
4.20 or higher.
Signed-off-by: David Bauer <mail@david-bauer.net>
Release notes since last update:
wave-1 firmware:
* Feb 14, 2019: Remove logic that causes assert when swba logic is not
initialized. This was seen when trying to bring up 6 VAP
vdevs. A similar fix went into wave-2 firmware some time
ago.
* Feb 27, 2019: Support up to 32 vAP vdevs, fix stack corruption when
driver requests too many vAP.
* Feb 28, 2019: Support beacon-tx-wmi callback message. This lets driver
properly clean up beacon buffers so we don't crash
(somethings the entire OS/system) due to DMA errors.
wave-2 firmware:
* Feb 27. 2019: Support up to 32 AP vdevs. Previous to this, stack would
be corrupted if you went past 16 AP vdevs.
* Feb 28, 2019: Support beacon-tx-wmi callback message. This lets driver
properly clean up beacon buffers. In wave-1, this could
crash the entire OS, but I didn't see the same crashes
in wave-2, so maybe it is fixed in some other way. Add
the feature regardless as it seems proper.
Signed-off-by: Michael Yartys <michael.yartys@gmail.com>
9360f389234a ath10k: Support up to 24 vAP per radio, fix DMA bug in wave-1.
9cbf8d430974 ath10k-ct: Add 4.20 driver, SGI support for fixed-rate tx.
Runtime tested on: ipq806x
Signed-off-by: Michael Yartys <michael.yartys@gmail.com>
The current snapshot release kernel with it's 2119245 Byte
size is too big to fit into the 2097152 (2MiB) area that
was set aside for the kernel. Which causes the device to
fail to boot (after an update or even during a fresh install)
NAND read: device 0 offset 0x60000, size 0x200000
2097152 bytes read: OK
## Booting kernel from Legacy Image at 80800000 ...
Image Name: MIPS OpenWrt Linux-4.14.98
Created: 2019-02-13 9:37:36 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 2119245 Bytes = 2 MiB
Load Address: 80002000
Entry Point: 80002000
Verifying Checksum ... Bad Data CRC
ERROR: can't get kernel image!
This patch fixes the problem by enlarging the kernel partition
at the cost of the ubi/data partition behind it. The patch
also adds a KERNEL_SIZE variable to the image Makefile to
prevent silent corruptions from happening in the future.
Please note: The u-boot environment for the router also
needs to be updated. So please attach an appropriate
serial converter cable and enter the following commands
into the u-boot prompt:
setenv nboot 'nand read 0x80800000 0x60000 0x300000; bootm 0x80800000'
saveenv
The wiki has been updated accordingly:
<https://openwrt.org/toh/zyxel/p2812hnu-f1>
Fixes: FS#2124
Suggested-by: Mafketel (User on bugs.openwrt.org)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
