Commit Graph

15 Commits

Author SHA1 Message Date
Pawel Dembicki
4e46ae1f69 kirkwood: add support for NETGEAR ReadyNAS Duo v2
NETGEAR ReadyNAS Duo v2 is a NAS based on Marvell kirkwood SoC.

Specification:
 - Processor Marvell 88F6282 (1.6 GHz)
 - 256MB RAM
 - 128MB NAND
 - 1x GBE LAN port (PHY: Marvell 88E1318)
 - 1x USB 2.0
 - 2x USB 3.0
 - 2x SATA
 - 3x button
 - 5x leds
 - serial on J5 connector accessible from rear panel
   (115200 8N1) (VCC,TX,RX,GND) (3V3 LOGIC!)

Installation by USB + serial:
  - Copy initramfs image to fat32 usb drive
  - Connect pendrive to USB 2.0 front socket
  - Connect serial console
  - Stop booting in u-boot
  - Do:
	usb reset
        setenv bootargs 'console=ttyS0,115200n8 earlyprintk'
        setenv bootcmd 'nand read.e 0x1200000 0x200000 0x600000;bootm 0x1200000'
        saveenv
	fatload usb 0:1 0x1200000 openwrt-kirkwood-netgear_readynas-duo-v2-initramfs-uImage
	bootm 0x1200000
  - copy sysupgrade image via ssh.
  - run sysupgrade

Installation by TFTP + serial:
  - Setup TFTP server and copy initramfs image
  - Connect serial console
  - Stop booting in u-boot
  - Do:
	setenv bootargs 'console=ttyS0,115200n8 earlyprintk'
	setenv bootcmd 'nand read.e 0x1200000 0x200000 0x600000;bootm 0x1200000'
	saveenv
	setenv serverip 192.168.1.1
	setenv ipaddr 192.168.1.2
	tftpboot 0x1200000 openwrt-kirkwood-netgear_readynas-duo-v2-initramfs-uImage
	bootm 0x1200000
  - copy sysupgrade image via ssh.
  - run sysupgrade

Known issues:
  - Power button and PHY INTn pin are connected to the same GPIO. It
    causes that every network restart button is pressed in system.
    As workaround, button is used as regular BTN_1.

For more info please look at file:
RND_5.3.13_WW.src/u-boot/board/mv_feroceon/mv_hal/usibootup/usibootup.c
from Netgear GPL sources.

Tested-by: Raylynn Knight <rayknight@me.com>
Tested-by: Lech Perczak <lech.perczak@gmail.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2021-12-29 20:35:57 +01:00
Pawel Dembicki
3843c641d8 kirkwood: add support for Ctera C200 V1 NAS
2-Bay NAS - maximum two 3.5" Harddisks

Hardware:
  - SoC: Marvell 88F6281-A1 ARMv5TE Processor 1.2GHz
  - Ram: 512MB (4x Nanya NT5TU128M8GE-AC)
  - NAND Flash: 256MB (Samsung 216 K9F2G08U0C)
  - Lan: 1x GBE (Marvell 88E1116R-NNC1)
  - Storage: 2x SATA HDD 3.5" Slot
  - USB: 2x USB 2.0 port
  - Console: Internal J3 connector (1: Vcc, 2: Rx, 3: Tx, 4: GND)
  - LEDs: 13x GPIO controlled
  - Buttons: 2x GPIO controlled

Known issues:
  - Buzzer is unused due lack of proper driver

Installation:
  - Apply factory initramfs image via stock web-gui.
  - Do sysupgrade to make installation complete.

Back to stock:
  - OpenWrt rootfs partition use unused space after stock firmware.
  - Full revert is possible.
  - Login via ssh and run: ctera_c200-v1_back_to_factory

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Reviewed-by: Sungbo Eo <mans0n@gorani.run>
[apply sorting to device recipe]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2021-12-04 09:39:11 +09:00
Bjørn Mork
25382dff85 kirkwood: sysupgrade: drop unnecessary UBI to UBI logic
The purpose of this code seems to be to avoid issues caused
by partially overwriting an existing UBI partition, where some
of the erase counters would be reset but not the unmodified
ones.  This problem has been solved in a more generic way by
the UBI EOF marker. This ensures that any old PEBs after the
marker are properly initialized.  It is therefore unnecessary
to erase the whole partition before flashing a new OpenWrt
factory image.

Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-12-03 12:23:02 +01:00
Adrian Schmutzler
65305cb448 kirkwood: use real model names for Linksys devices
This replaces the internal device names "Audi" and "Viper" with the
real model names, which a user would look for. This makes the
Linksys devices on this target consistent with the names recently
changed for mvebu based on the same idea.

As a consequence, the "viper" device definition is split into two
separate definitions with the correct names for both real models.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-31 15:03:43 +02:00
Rafał Miłecki
8b4bc7abe0 treewide: sysupgrade: don't use $ARGV in platform_do_upgrade()
stage2 passes image path to platform_do_upgrade() as an argument so it
can be simply accessed using $1

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2019-07-17 08:05:38 +02:00
Jeff Kletsky
b3770eaca3 mtd: base-files: Unify dual-firmware devices (Linksys)
Consistently handle boot-count reset and upgrade across
ipq40xx, ipq806x, kirkwood, mvebu

Dual-firmware devices often utilize a specific MTD partition
to record the number of times the boot loader has initiated boot.

Most of these devices are NAND, typically with a 2k erase size.
When this code was ported to the ipq40xx platform, the device in hand
used NOR for this partition, with a 16-byte "record" size. As the
implementation of `mtd resetbc` is by-platform, the hard-coded nature
of this change prevented proper operation of a NAND-based device.

* Unified the "NOR" variant with the rest of the Linksys variants

* Added logging to indicate success and failure

* Provided a meaningful return value for scripting

* "Protected" the use of `mtd resetbc` in start-up scripts so that
   failure does not end the boot sequence

* Moved Linksys-specific actions into common `/etc/init.d/bootcount`

For upgrade, these devices need to determine which partition to flash,
as well as set certain U-Boot envirnment variables to change the next
boot to the newly flashed version.

* Moved upgrade-related environment changes out of bootcount

* Combined multiple flashes of environment into single one

* Current-partition detection now handles absence of `boot_part`

Runtime-tested: Linksys EA8300

Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[checkpatch.pl fixes, traded split strings for 80+ chars per line]
2019-05-18 13:43:51 +02:00
尤晓杰
a7e62b4be1 kirkwood: fix sysupgrade
The platform_check_image() stub need to return 0 for success, otherwise
the sysupgrade will fail with:

  Image check 'platform_check_image' failed.

Fixes: aa6f5f1787 ("kirkwood: use image metadata")
Signed-off-by: 尤晓杰 <yxj790222@163.com>
[reworded commit message}
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-18 07:26:28 +01:00
Mathias Kresin
c9e2c35f46 kirkwood: use the generic board detect
Drop the target specific detection function in favour of the generic
one provided by base-files.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-09 22:06:55 +01:00
Mathias Kresin
aa6f5f1787 kirkwood: use image metadata
Append and enforce image metadata. Remove the device specific image
checks, they are replaced by image metadata.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-09 22:06:55 +01:00
Mathias Kresin
f12a32630f treewide: use the generic board_name function
Use the generic function instead ot the target specific ones.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-07-15 23:13:34 +02:00
Matthias Schiffer
438dcbfe74
base-files: automatically handle paths and symlinks for RAMFS_COPY_BIN
Depending on busybox applet selection, paths of basic utiilties may differ,
and may not work as symlinks to busybox. Simply using whatever binary is
found in PATH and detecting symlinks automatically is more robust and
easier to maintain.

The list of binaries is also slightly cleaned up and duplicates are
removed.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2017-07-11 17:26:32 +02:00
Matthias Schiffer
f464da623d
kirkwood: upgrade: fix RAMFS_COPY_*
RAMFS_COPY_* are moved to platform.sh toplevel. The nand_do_upgrade call is
moved to platform_do_upgrade.

Fixes: 30f61a34b4 "base-files: always use staged sysupgrade"
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2017-07-11 17:19:23 +02:00
Felix Fietkau
83d59453c0 kirkwood: fix sysupgrade for non-dockstar NAND devices
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-12-30 12:58:20 +01:00
Luka Perkov
afa1c47e71 kirkwood/dockstar: use ubi(kernel, squashfs, ubifs) images
The new image requires `bootz` because of devicetree appending.
To flash a new image boot initramfs:

  tftpboot 0x800000 openwrt-kirkwood-dockstar-initramfs-kernel.bin
  bootz 0x800000

  # detach if already attached
  ubidetach -p /dev/$(grep ubi /proc/mtd|awk -F: '{print $1}')
  # scp openwrt-kirkwood-dockstar-squashfs-factory.bin /tmp
  ubiformat -f /tmp/openwrt-kirkwood-dockstar-squashfs-factory.bin
  # attach is important to resize rootfs_data otherwise it wont boot
  ubiattach -p /dev/$(grep ubi /proc/mtd|awk -F: '{print $1}')

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>

SVN-Revision: 49010
2016-03-14 17:06:09 +00:00
Luka Perkov
b0e7ca4f8f kirkwood: support sysupgrade on Linksys EA[34]500
This automatically writes to the alternate firmware partition
(on Linksys's dual firmware layout) using code borrowed from
the WRT1900AC port.

Signed-off-by: Claudio Leite <leitec@staticky.com>

SVN-Revision: 47434
2015-11-10 00:16:42 +00:00