We can now use the power LED for diag in more devices thanks to the latest
patches from the RPi foundation.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Use approach suggested by Adrian Schmutzler instead of introducing
another device variable.
Also revert the unnecessary white-space changes accidentally introduced
by the previous commit.
Fixed: c067b1e79b ("mediatek: move out-of-tree DTS files to dedicated dts folder")
Suggested-by: Adrian Schmutzler <mail@adrianschmutzler.de>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Use dedicated dts folder like on ramips to store device tree source
files for boards not already supported in vanilla Linux.
Doing so instead of having them in files-* has several advantages:
* we don't need to duplicate them for several kernel versions
* changes to a device tree don't trigger a complete kernel rebuild
* the files are more obvious to find
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Ran update_kernel.sh in a fresh clone without any existing toolchains.
No manual changes needed.
Build system: x86_64
Build-tested: bcm27xx/bcm2711
Signed-off-by: John Audia <graysky@archlinux.us>
The USB ports if a FRIZZ!Box 7320 do not supply power to connected
devices.
Add the GPIOs enabling USB power as regulator, to enable USB power
supply as soon as the USB driver is loaded.
Fixes FS#3624
Signed-off-by: Mathias Kresin <dev@kresin.me>
When recursively deleting partitions, don't acquire the masters
partition lock twice. Otherwise the process endy up in a deadlocked
state.
Signed-off-by: David Bauer <mail@david-bauer.net>
Hardware
--------
MediaTek MT7622
512MB DDR3 RAM
64M SPI-NOR Flash (Winbond W25Q512JV)
MediaTek MT7622 802.11bgn 4T4R WMAC
MediaTek MT7915 802.11ax 4T4R
Marvell AQR1112 100/1000/2500 NBase-T PHY
Holtek HT32F52241 LED controller
Reset Switch
UART
----
CPU UART0 at the pinout next to the Holtek MCU.
Pinout (first pin next to SoC / MCU)
0 3V3
1 RX
2 TX
3 GND
Settings are 115200 8N1.
Opening the case
----------------
Opening the case is not a nice task, as itis glued together. Insert a
flat knife between the front and back casing below the ethernet port.
Open up a gap this way and insert a flat scredriver, remove the knife.
Work your way around the casing by applying force to seperate the front
and back casing. This losens the glue and opens the plastic clips. Be
gentle, as these clips are very cheap and break quickly.
Installation
------------
1. Connect to the booted device at 192.168.1.20 using username/password
"ubnt".
2. Transfer the OpenWrt sysupgrade image to the device using SCP.
3. Check the mtd partition number for bs / kernel0 / kernel1
$ cat /proc/mtd
4. Set the bootselect flag to boot from kernel0
$ dd if=/dev/zero bs=1 count=1 of=/dev/mtdblock6
5. Write the OpenWrt sysupgrade image to both kernel0 as well as kernel1
$ dd if=openwrt.bin of=/dev/mtdblock8
$ dd if=openwrt.bin of=/dev/mtdblock9
6. Reboot the device. It should boot into OpenWrt.
Signed-off-by: David Bauer <mail@david-bauer.net>
Add a driver for controlling the RGB LED via Ubiquitis own "LEDBAR" LED
controller based on the Holtek HT32F52241 MCU.
This driver is initially used by the Ubiquiti UniFi 6 LR, however
judging from FCC pictures the MCU is also found on the U6-Mesh as well
as the U6-Extender.
Signed-off-by: David Bauer <mail@david-bauer.net>
This patch has been added to 5.4, but not been copied to 5.10:
7495acb555 ("kernel: backport mtd commit converting partitions doc syntax")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This applies another patch from 5.4 to 5.10 as well:
de09355f74 ("kernel/hack-5.4: make UDP tunneling user-selectable")
UDP tunneling support isn't user-selectable, but it's required by WireGuard
which is, for the time being, an out-of-tree module. We currently work around
this issue by selecting an unrelated module which depends on UDP tunnelling
(VXLAN). This is inconvenient, as it implies this unrelated module needs to be
built-in when doing a monolithic build.
Fix this inconvenience by making UDP tunneling user-selectable in the kernel
configuration.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
File extension was truncated for
pending-5.4/770-11-net-ethernet-mtk_eth_soc-avoid-rearming-interrupt-if.pa
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reapply changes added to 5.4 but not copied to 5.10:
3da4acaa7b ("kernel: fix busy wait loop in mediatek PPE code")
The intention is for the loop to timeout if the body does not succeed.
The current logic calls time_is_before_jiffies(timeout) which is false
until after the timeout, so the loop body never executes.
time_is_after_jiffies(timeout) will return true until timeout is less
than jiffies, which is the intended behavior here.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Kernel has changed the of_get_phy_mode API in commit 0c65b2b90d13
("net: of_get_phy_mode: Change API to solve int/unit warnings").
This is already included in kernel 5.5, so fix the version switch
(though this will not actually matter for the versions we support).
Similar driver adjustments to account for the API change will
probably be necessary to various other local drivers.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This adds quirks support to the "ofpart" parser. It's required to
support fixed partitions that require some extra logic.
Right now only BCM4908 binding is supported (BCM4908 requires detecting
currently used "firmware" partition).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The intention is for the loop to timeout if the body does not succeed.
The current logic calls time_is_before_jiffies(timeout) which is false
until after the timeout, so the loop body never executes.
time_is_after_jiffies(timeout) will return true until timeout is less
than jiffies, which is the intended behavior here.
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
The Netgear EX6150 has an Access Point/Extender switch. Set it as
an EV_SW. Otherwise when it's set to Access Point, it will trigger
failsafe mode during boot.
Fixes: FS#3590
Signed-off-by: Kurt Roeckx <kurt@roeckx.be>
This reverts commit 4968fc8fb1 as the bump
to v2021.01 needs swig on the host for pylibfdt which is needed by dtoc
tool to generate .h/.c files from DTBs in SPL for mx6cuboxi_config.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The factory images need to embed specific IDs to pass verification with
the OEM firmware (including TFTP recovery), so they need to be
per-device variables.
Fixes: ab1584a797 ("ath79: netgear: trim down uImage customisations")
Fixes: 459c8c9ef8 ("ath79: add support for ZyXEL NBG6616")
Reported-by: Marcin Juszkiewicz <marcin-openwrt@juszkiewicz.com.pl>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
[minor commit message adjustments, sort DEVICE_VARS]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
There are proper workarounds merged to 5.4 stable tree for ESPRESSObin
boards with older bootloader:
4e1a23779bde ("ata: ahci: mvebu: Make SATA PHY optional for Armada 3720")
40af962eb1d4 ("usb: host: xhci: mvebu: make USB 3.0 PHY optional for
Armada 3720")
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
The bootloader of a number of recent TP-Link devices does not properly
initialise the MT7621's internal switch when booting from flash. To
enable the mt7530 driver to clear the reset on the switch, the ramips
reset controller must be allowed to toggle these.
Backport upstream commit 3f9ef7785a9c from mips-next to allow control of
the "mcm" reset line.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Upstream in commit 8b9c0cb46471 ("apalis_imx6: boot env configuration
updates") removed emmc legacy wrappers, but so far didn't included any
replacements. Fix it by simply defining the missing variables and UUID
gathering directly into the boot script.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Our patch refresh tool creates quite a big diff for these patches,
as it does not use rename syntax.
Push the refresh separately so it does not pollute the next kernel
bump. This is a purely cosmetic change.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The original setup fails to trigger ART calibration data
extraction for the AR9287. Instead, it would only have extracted
calibration data for an internal WMAC chip which is not present on
this board.
Fixes: 55d2db0e8c ("ath79: add support for Meraki MR12")
Signed-off-by: Martin Kennedy <hurricos@gmail.com>
[commit title/message facelift]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Initial commit 8375623a06 ("ramips: add support for TP-Link Archer
C2") contains detailed installation instructions, which do not mention
a factory image. From what I can see, no support to install OpenWrt
through the vendor web interface has been added since. The factory
image is also conspicuously absent from the device page in the wiki.
Yet, it is available for download.
I bricked my Archer C2 loading the factory image through the web UI.
Serial showed this error during bootloop:
Uncompressing Kernel Image ... LZMA ERROR 1 - must RESET board to recover
This patch disables the undocumented factory image so users won't get
tricked into thinking easy web UI flashing actually works.
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
The Netgear GS108T v3 is an 8 port gigabit switch with PoE-PD support
on port 1. The two prior versions were built using eCos and are not
currently compatible with OpenWRT.
The GS108T v3 is quite similar to both the GS110TPP v1 and GS110TP v3,
all of which use the same firmware image from Netgear. For this reason,
the device tree is identical aside from the model and compatible values.
All of the above feature a dual firmware layout, referred to as Image0
and Image1 in the Netgear firmware.
Hardware specification
----------------------
* RTL8380M SoC, 1 MIPS 4KEc core @ 500MHz
* 128MB DDR3-1600 DRAM (Winbond W631GG8MB-12)
* 32MB 3v NOR SPI Flash (Macronix MX25L25635F or Winbond W25Q256JVFIQ)
* RTL8231 GPIO extender to control the LEDs and the reset button
* 8 x 10/100/1000BASE-T ports, internal PHY (RTL8218B)
* UART (115200 8N1) via unpopulated standard 0.1" pin header marked J1
* Power is supplied via a 12V 1A barrel connector or 802.3af
UART pinout
-----------
J1 | [o]ooo
^ ||`------ GND
| |`------- RX [TX out of the serial adapter]
| `-------- TX [RX into the serial adapter]
`---------- Vcc (3V3) [the square pin]
The through holes are filled with PB-free solder which melts at 375C.
They can also be drilled using a 0.9mm bit.
Build configuration
-------------------
* Target System: Realtek MIPS
* Target Profile: Netgear GS108T v3
* Target Images -> ramdisk -> Compression: lzma
* Disable other target images
Boot initramfs image from U-Boot
--------------------------------
1. Press the Escape key at the `Hit Esc key to stop autoboot` prompt
2. Init network with `rtk network on` command
3. Load image with `tftpboot 0x8f000000 openwrt-realtek-generic-netgear_gs108t-v3-initramfs-kernel.bin` command
4. Boot the image with `bootm` command
The switch defaults to IP 192.168.1.1 and tries to fetch the image via
TFTP from 192.168.1.111.
Updating the installed firmware
-------------------------------
The OpenWRT ramdisk image can be flashed directly from the Netgear UI.
The Image0 slot should be used in order to enable sysupgrade.
As with similar switches, changing the active boot partition can be
accomplished in U-Boot as follows:
1. Press the Escape key at the `Hit Esc key to stop autoboot` prompt
2. Run `setsys bootpartition {0|1}` to select the boot partition
3. Run `savesys` followed by `boota` to proceed with the boot process
Signed-off-by: Michael Mohr <akihana@gmail.com>
Move most of the GS110TPP v1 device tree into a dtsi so that it can be
shared with the GS108T v3. Additionally:
* Use macros to simplify the ethernet and switch definitions
* Zero-pad the offsets and sizes in the partition map to 8 digits each
The spi-max-frequency value has been changed from 10MHz to 50MHz based
on an analysis of the relevant datasheets. The current driver doesn't
use this property, as the clock speed is fixed. However, it's required
for this type of DT node, so that's why it's present here.
The firmware partition has been split in half, since this is how the
stock firmware uses it. This can be used to easily revert to a stock
firmware if one is written to the second image area.
Signed-off-by: Michael Mohr <akihana@gmail.com>
The netgear_nge device will be shared between the GS108T v3 (to be added
in a later commit) and the GS110PP v1. It also enables LZMA compression
for the ramdisk image.
Signed-off-by: Michael Mohr <akihana@gmail.com>
The TP-Link TL-WR810N v1 is known to cause soft-brick on ath79 and
work fine for ar71xx [1]. On closer inspection, the only apparent
difference is the GPIO used for the USB regulator, which deviates
between the two targets.
This applies the value from ar71xx to ath79.
Tested successfully by a forum user.
[1] https://forum.openwrt.org/t/tp-link-tl-wr810n-v1-ath79/48267
Fixes: cdbf2de777 ("ath79: Add support for TP-Link WR810N")
Fixes: FS#3522
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Specifications:
- SoC: MediaTek MT7621AT
- RAM: 128 MB (DDR3)
- Flash: 16 MB (SPI NOR)
- WiFi: MediaTek MT7603E, MediaTek MT7612E
- Switch: 1 WAN, 4 LAN (Gigabit)
- Ports: 1 USB 3.0
- Buttons: Reset, WPS
- LEDs: Power, System, Wan, Lan 1-4, WiFi 2.4G, WiFi 5G, WPS, USB
- Power: DC 12V 1A tip positive
UART Serial:
115200 baud
Located on unpopulated 4 pin header near J4:
J4
[o] Rx
[o] Tx
[o] GND
[ ] Vcc - Do not connect
Installation:
Download and flash the manufacturer's built OpenWRT image available at
http://www.cudytech.com/openwrt_software_download
Install the new OpenWRT image via luci (System -> Backup/Flash firmware)
Be sure to NOT keep settings. The force upgrade may need to be checked
due to differences in router naming conventions.
Recovery:
- Loads only signed manufacture firmware due to bootloader RSA verification
- serve tftp-recovery image as /recovery.bin on 192.168.1.88/24
- connect to any lan ethernet port
- power on the device while holding the reset button
- wait at least 8 seconds before releasing reset button for image to
download
- See http://www.cudytech.com/newsinfo/547425.html
MAC addresses as verified by OEM firmware:
use address source
LAN *:f0 label
WAN *:f1 label + 1
2g *:f0 label
5g *:f2 label + 2
The label MAC address is found in bdinfo 0xde00.
Signed-off-by: Andrew Pikler <andrew.pikler@gmail.com>
Specifications:
* QCA9557, 16 MiB Flash, 128 MiB RAM, 802.11n 2T2R
* QCA9882, 802.11ac 2T2R
* 2x Gigabit LAN (1x 802.11af PoE)
* IP68 pole-mountable outdoor case
Installation:
* Factory Web UI is at 192.168.0.50
login with 'admin' and blank password, flash factory.bin
* Recovery Web UI is at 192.168.0.50
connect network cable, hold reset button during power-on and keep it
pressed until uploading has started (only required when checksum is ok,
e.g. for reverting back to oem firmware), flash factory.bin
After flashing factory.bin, additional free space can be reclaimed by
flashing sysupgrade.bin, since the factory image requires some padding
to be accepted for upgrading via OEM Web UI.
Both ethernet ports are set to LAN by default, matching the labelling on
the case. However, since both GMAC Interfaces eth0 and eth1 are connected
to the switch (QCA8337), the user may create an additional 'wan' interface
as desired and override the vlan id settings to map br-lan / wan to either
the PoE or non-PoE port, depending on the individual scenario of use.
So, the LAN and WAN ports would then be connected to different GMACs, e.g.
config interface 'lan'
option ifname 'eth0.1'
...
config interface 'wan'
option ifname 'eth1.2'
...
config switch_vlan
option device 'switch0'
option vlan '1'
option ports '1 0t'
config switch_vlan
option device 'switch0'
option vlan '2'
option ports '2 6t'
Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
[add configuration example]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Have the port use GMAC1 with internal switch
which fixes the issue of the ethernet LED not functioning
The LED is triggered by the internal switch, not a GPIO.
The GPIO for the ethernet LED was added in ath79
as it was defined in the ar71xx target
but it was not functioning in ath79 for a previously unknown reason.
It is unknown why that GPIO was defined as an LED in ar71xx.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
[drop unrelated changes: model property and SPI max frequency]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
for:
- ENH202 v1
- ENS202EXT v1
- EnstationAC v1
- EWS511AP
For EWS511AP, have default behavior as static ip
to match the behavior of all other APs in ath79
These boards are sold as
Client Bridge or Point to Point or Access Point
so there is probably no benefit to have WAN by default
for one of the ports, to prevent user confusion.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
While the latest version of 19.07 release is usable,
the current master is unbootable on the device in a normal way.
"Normal way" installations includes:
- sysupgrade (e.g. from 19.07)
- RESET button recovery with Ron Curry's (Wingspinner) UBoot image
(10.10.10.3 + "Kernal.bin")
- RESET button recovery with original U-Boot
(10.10.10.254 + "kernel")
One could flash and boot the latest master sysupgrade image successfully
with serial access to the device. But a sysupgrade from this state still
breaks the U-Boot and soft-bricks the device.
Signed-off-by: Szabolcs Hubai <szab.hu@gmail.com>
shellcheck recommends || and && over "-a" and "-o" because the
latter are not well defined.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The hardware random number generator driver for bcm63xx was merged with
the one used by the Raspberry Pi. Now this driver is lost.
Reenable the HW_RANDOM kernel config with the new driver.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
[refresh kernel config]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Instead of taking the input of one temperature sensor (temp1), the
script takes into account three temperature sensors to control the
PWM of the cooling fan.
temp1 -> placed on main board
temp2 -> placed on main board
temp3 -> placed on or close to chipset
All three temperatures give valid input for the PWM of the fan on
NSA310 and are actually changing.
Tested on two NSA310.
Signed-off-by: Thomas Beckler <thomas.beckler@hotmail.com>
Reviewed-by: Alberto Bursi <bobafetthotmail@gmail.com>
[commit title/message facelift, code cleanup]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
FRITZ!Box 7412 loads the firmware for fast ethernet PHY and mii is
more accurate in this case.
Gmii is used by Gigabit ethernet PHYs.
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
Reviewed-by: Mathias Kresin <dev@kresin.me>
[minor commit title/message adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This replaces a full-text BSD clause by the corresponding SPDX
identifier.
This should make it easier to identify the license both by humans
and machines.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This replaces several full-text and abbreviated licenses found in
DTS files by the corresponding SPDX identifiers.
This should make it easier to identify the license both by humans
and machines.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
UniElec U7621-01 is a router platform board, the smaller model of
the U7621-06.
The device has the following specifications:
- MT7621AT (880 MHz)
- 256 of RAM (DDR3)
- 16 MB of FLASH (SPI NOR)
- 5x 1 Gbps Ethernet (MT7621 built-in switch)
- 1x 2.4Ghz MT7603E
- 1x 5Ghz MT7612
- 1x miniPCIe slots (PCIe bus only)
- 1x miniSIM slot
- 1x USB 2.0 (uses the usb 3.0 driver)
- 8x LEDs (1x GPIO-controlled)
- 1x reset button
- 1x UART header (4-pins)
- 1x GPIO header (30-pins)
- 1x DC jack for main power (12 V)
The following has been tested and is working:
- Ethernet switch
- 1x 2.4Ghz MT7603E (wifi)
- 1x 5Ghz MT7612 (wifi)
- miniPCIe slots (tested with Wi-Fi cards and LTE modem cards)
- miniSIM slot (works with normal size simcard)
- sysupgrade
- reset button
Installation:
This board has no locked down bootloader. The seller can be asked to
install openwrt v18.06, so upgrades are standard sysupgrade method.
Recovery:
This board contains a Chinese, closed-source bootloader called Breed
(Boot and Recovery Environment for Embedded Devices). Breed supports web
recovery and to enter it, you keep the reset button pressed for around
5 seconds during boot. Your machine will be assigned an IP through DHCP
and the router will use IP address 192.168.1.1. The recovery website is
in Chinese, but is easy to use. Click on the second item in the list to
access the recovery page, then the second item on the next page is where
you select the firmware. In order to start the recovery, you click the
button at the bottom.
LEDs list (left to right):
- ESW_P0_LED_0
- ESW_P1_LED_0
- ESW_P2_LED_0
- ESW_P3_LED_0
- ESW_P4_LED_0
- CTS2_N (GPIO10, configured as "status" LED)
- LED_WLAN# (connected with pin 44 in wifi1 slot)
Signed-off-by: David Bentham <db260179@gmail.com>
[add DEVICE_VARIANT, fix DEVICE_PACKAGES, remove &gpio]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Port device support for Meraki MR12 from the ar71xx target to ath79.
Specifications:
- SoC: AR7242-AH1A CPU
- RAM: 64MiB (NANYA NT5DS32M16DS-5T)
- NOR Flash: 16MiB (MXIC MX25L12845EMI-10G)
- Ethernet: 1 x PoE Gigabit Ethernet Port (SoC MAC + AR8021-BL1E PHY)
- Ethernet: 1 x 100Mbit port (SoC MAC+PHY)
- Wi-Fi: Atheros AR9283-AL1A (2T2R, 11n)
Installation:
1. Requires TFTP server at 192.168.1.101, w/ initramfs & sysupgrade .bins
2. Open shell case
3. Connect a USB->TTL cable to headers furthest from the RF shield
4. Power on the router; connect to U-boot over 115200-baud connection
5. Interrupt U-boot process to boot Openwrt by running:
setenv bootcmd bootm 0xbf0a0000; saveenv;
tftpboot 0c00000 <filename-of-initramfs-kernel>.bin;
bootm 0c00000;
6. Copy sysupgrade image to /tmp on MR12
7. sysupgrade /tmp/<filename-of-sysupgrade>.bin
Notes:
- kmod-owl-loader is still required to load the ART partition into the
driver.
- The manner of storing MAC addresses is updated from ar71xx; it is
at 0x66 of the 'config' partition, where it was discovered that the
OEM firmware stores it. This is set as read-only. If you are
migrating from ar71xx and used the method mentioned above to
upgrade, use kmod-mtd-rw or UCI to add the MAC back in. One more
method for doing this is described below.
- Migrating directly from ar71xx has not been thoroughly tested, but
one method has been used a couple of times with good success,
migrating 18.06.2 to a full image produced as of this commit. Please
note that these instructions are only for experienced users, and/or
those still able to open their device up to flash it via the serial
headers should anything go wrong.
1) Install kmod-mtd-rw and uboot-envtools
2) Run `insmod mtd-rw.ko i_want_a_brick=1`
3) Modify /etc/fw_env.config to point to the u-boot-env partition.
The file /etc/fw_env.config should contain:
# MTD device env offset env size sector size
/dev/mtd1 0x00000 0x10000 0x10000
See https://openwrt.org/docs/techref/bootloader/uboot.config
for more details.
4) Run `fw_printenv` to verify everything is correct, as per the
link above.
5) Run `fw_setenv bootcmd bootm 0xbf0a0000` to set a new boot address.
6) Manually modify /lib/upgrade/common.sh's get_image function:
Change ...
cat "$from" 2>/dev/null | $cmd
... into ...
(
dd if=/dev/zero bs=1 count=$((0x66)) ; # Pad the first 102 bytes
echo -ne '\x00\x18\x0a\x12\x34\x56' ; # Add in MAC address
dd if=/dev/zero bs=1 count=$((0x20000-0x66-0x6)) ; # Pad the rest
cat "$from" 2>/dev/null
) | $cmd
... which, during the upgrade process, will pad the image by
128K of zeroes-plus-MAC-address, in order for the ar71xx's
firmware partition -- which starts at 0xbf080000 -- to be
instead aligned with the ath79 firmware partition, which
starts 128K later at 0xbf0a0000.
7) Copy the sysupgrade image into /tmp, as above
8) Run `sysupgrade -F /tmp/<sysupgrade>.bin`, then wait
Again, this may BRICK YOUR DEVICE, so make *sure* to have your
serial cable handy.
Signed-off-by: Martin Kennedy <hurricos@gmail.com>
[add LED migration and extend compat message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Specifications:
- SoC: MediaTek MT7688AN
- RAM: 128 MB
- Flash: 32 MB
- Ethernet: 5x 10/100 (1x WAN, 4x LAN)
- Wireless: built in 2.4GHz (bgn)
- USB: 1x USB 2.0 port
- Buttons: 1x Reset
- LEDs: 1x (WiFi)
Flash instructions:
- Configure TFTP server with IP address 10.10.10.3
- Name the firmware file as firmware.bin
- Connect any Ethernet port to the TFTP server's LAN
- Choose option 2 in U-Boot
- Alternatively choose option 7 to upload firmware to the built-in
web server
MAC addresses as verified by OEM firmware:
use address source
2g *:XX factory 0x4
LAN *:XX+1 factory 0x28
WAN *:XX+1 factory 0x2e
Notes:
This board is ostensibly a module containing the MediaTek MT7688AN SoC,
128 MB DDR2 SDRAM and 32 MB flash storage. The SoC can be operated in
IoT Gateway Mode or IoT Device Mode.
From some vendors the U-Boot that comes installed operates on UART 2
which is inaccessible in gateway mode and operates unreliably in the
Linux kernel when using more than 64 MB of RAM. For those, updating
U-Boot is recommended.
Signed-off-by: Ewan Parker <ewan@ewan.cc>
[add WLAN to 01_leds]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Ran update_kernel.sh in a fresh clone without any existing toolchains.
Removed upstreamed patches:
imx6: 303-ARM-dts-imx6qdl-gw52xx-fix-duplicate-regulator-namin.patch
Build system: x86_64
Build-tested: ipq806x/R7800, bcm27xx/bcm2711
Run-tested: ipq806x/R7800
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
The PCI device ID detected by the wifi drivers on devices using a fallback
SPROM is wrong. Currently the chipnum is used for this parameter.
Most SSB based Broadcom wifi chips are 2.4 and 5GHz capable. But on
devices without a physical SPROM, the only one way to detect if the device
suports both bands or only the 5GHz band, is by reading the device ID from
the fallback SPROM.
In some devices, this may lead to a non working wifi on a 5GHz-only card,
or in the best case a working 2.4GHz-only in a dual band wifi card.
The offset for the deviceid in SSB SPROMs is 0x0008, whereas in BCMA is
0x0060. This is true for any SPROM version.
Override the PCI device ID with the one defined at the fallback SPROM, to
detect the correct wifi card model and allow using the 5GHz band if
supported.
The patch has been tested with the following wifi radios:
BCM43222: b43: both 2.4/5GHz working
brcm-wl: both 2.4/5GHz working
BCM43225: b43: 2.4GHz, working
brcmsmac: working
brcm-wl: it lacks support
BCM43217: b43: 2.4GHz, working
brcmsmac: it lacks support
brcm-wl: it lacks support
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
[amend commit description, rework patch to avoid using a new global variable
and keep ssb sprom extraction code as close to ssb/pci.c as possible]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
New upstream changes extract more SPROM values and fix the antenna gain.
These changes can be found in linux drivers/ssb/pci.c.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
All modification made by update_kernel.sh in a fresh clone without
existing toolchains.
Build-tested: bcm27xx/bcm2711, ipq806x/R7800,
Run-tested: ipq806x/R7800
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
Add statistics to ethtool. The statistics can be useful to
debug network issues.
The code is backported from mainline ag71xx.c driver.
Signed-off-by: Leon Leijssen <leon.git@leijssen.info>
Hardware
--------
Atheros AR7241
16M SPI-NOR
64M DDR2
Atheros AR9283 2T2R b/g/n
2x Fast Ethernet (built-in)
Installation
------------
Transfer the Firmware update to the device using SCP.
Install using fwupdate.real -m <openwrt.bin> -d
Signed-off-by: David Bauer <mail@david-bauer.net>
Enable support for the Ubiquiti UniFi Outdoor+ RF filter via
device-tree. The old way of using platform data is not required anymore,
as it was only used on the now removed ar71xx target.
Signed-off-by: David Bauer <mail@david-bauer.net>
Currently it's not possible to boot the device with just initramfs image
without additional effort as the initramfs image doesn't contain device
tree. Fix it by producing FIT based image which could be booted with
following commands:
setenv bootargs earlyprintk console=ttyS0,115200
tftpboot ${kernel_addr_r} openwrt-mvebu-cortexa9-cznic_turris-omnia-initramfs-kernel.bin
bootm ${kernel_addr_r}
Acked-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Reviewed-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The thermal zones kernel documentation is misleading, we cannot use more
than one sensor in a thermal zone node.
Furthermore the drivetemp driver for some reason it only catches one
sensor from the hard drives array (the first available).
In the Buffalo Linkstation LS421DE board there is also a sensor at the
ethernet phy chip that can also be monitored. Very useful to stop the fan
when there are no hard drives in the bays.
(It might be also possible to add the CPU sensor, but it requires kernel
patching for registering the sensor via device tree, using the function:
devm_thermal_zone_of_sensor_register)
Fix the thermal zones to use only one sensor per node and add the ethernet
phy sensor. Also adjust the hdd temperatures to be more conservative for
a mechanical hard drive.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
A header used in ELECOM WRC-300GHBK2-I and WRC-1750GHBK2-I/C is also
used in ELECOM WRC-2533GHBK-I, so split the code to generate the header
and move it to image-commands.mk to use from ramips target.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Reviewed-by: Sungbo Eo <mans0n@gorani.run>
This drops the shebang from another bunch of files in various /lib
folders, as these are sourced and the shebang is useless.
Fix execute bit in one case, too.
This should cover almost all trivial cases now, i.e. where /lib is
actually used for library files.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Calling netdev_reset_queue() from _stop() functions is causing sporadic kernel
panics on bcm63xx, which happen mainly on BCM6318 and BCM6328.
This reverts to the previous behaviour, which called netdev_reset_queue() from
_open() functions.
Tested on Comtrend AR-5315u (BCM6318).
Fixes: 1d6f422e34 ("bcm63xx: sync ethernet driver with net-next")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This sets SUPPORTED_DEVICES to match the compatible in the DTS.
While at it, synchronize the capitalization in DEVICE_MODEL and
DTS model.
Signed-off-by: Marty Jones <mj8263788@gmail.com>
[commit title/message facelift, move variable in armv8.mk]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This sorts the Build recipes alphabetically, wraps some long lines
and moves the DEVICE_VARS to the top like common on several other
targets.
Cc: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
We have support for reference boards available on this target, so
support for an additional generic profile does not make much sense.
Remove it to have one thing less to maintain.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Paul Spooren <mail@aparcar.org>
On a platform with many very different devices, like found on kirkwood,
the generic profile seems like a remnant of the past that does not
have a real use anymore.
Remove it to have one thing less to maintain.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Paul Spooren <mail@aparcar.org>
On a platform with many very different devices, like found on ipq806x,
the generic profile seems like a remnant of the past that does not
have a real use anymore.
Remove it to have one thing less to maintain.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Paul Spooren <mail@aparcar.org>
On a platform with many very different devices, like found on ipq40xx,
the generic profile seems like a remnant of the past that does not
have a real use anymore.
Remove it to have one thing less to maintain.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Paul Spooren <mail@aparcar.org>
On a platform with many very different devices, like found on ramips,
the generic profiles seem like remnants of the past that do not
have a real use anymore.
Remove them to have one thing less to maintain.
Actually, rt288x didn't have a default profile in the first place.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Paul Spooren <mail@aparcar.org>
On a platform with many very different devices, like found on ath79,
the generic profiles seem like remnants of the past that do not
have a real use anymore.
Remove them to have one thing less to maintain.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Paul Spooren <mail@aparcar.org>
Add a table API that has per accss register locking and uses
register description information to handle all table access
through a single set of api calls.
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
