Stock firmware has a vendor-defined tail at the end of uImage for image
validation. This patch enables OpenWrt installation from stock firmware
without having to access the UART console.
Installation via web interface:
1. Flash **initramfs** image through the stock web interface.
2. Boot into OpenWrt and perform sysupgrade with sysupgrade image.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
The correct model name of WF-2881 is WF2881 without hyphen. The former used
boardnames are not added to SUPPORTED_DEVICES, to make it explicit that the
sysupgrade-tar image, which is newly added in the previous commit, should
not be used to upgrade from older version.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[adjust commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
WF-2881 sysupgrade image uses UBI rootfs, but still relies on
default_do_upgrade. Because of this, config backup is not restored after
sysupgrade. It can be fixed by switching to nand_do_upgrade and
sysupgrade-tar image. default_do_upgrade does not handle sysupgrade-tar
properly, so one should use factory image to upgrade from older version.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
This commit adds the ability to set custom uImage magic to
Build/wr1201-factory-header and renames it to
"Build/custom-initramfs-uimage".
Custom uImage header in initramfs image is required on following
devices:
- I-O DATA WN-AX1167GR2
- I-O DATA WN-AX2033GR
- I-O DATA WN-AX2033GR2
- I-O DATA WN-DX1167R
While at it, fix typo in comment.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Reviewed-by: Sungbo Eo <mans0n@gorani.run>
[shorten commit title, minor commit message adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
TP-Link RE200 v2 is a wireless range extender with Ethernet and 2.4G and 5G
WiFi with internal antennas. It's based on MediaTek MT7628AN+MT7610EN.
Specifications
--------------
- MediaTek MT7628AN (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 1T1R 5 GHz
- 1x 10/100 Mbps Ethernet
- UART header on PCB (57600 8n1)
- 8x LED (GPIO-controlled), 2x button
There are 2.4G and 5G LEDs in red and green which are controlled
separately.
MAC addresses
-------------
The MAC address assignment matches stock firmware, i.e.:
LAN : *:0D
2.4G: *:0E
5G : *:0F
Installation
------------
Web Interface
-------------
It is possible to upgrade to OpenWrt via the web interface. Simply flash
the -factory.bin from OEM. In contrast to a stock firmware, this will not
overwrite U-Boot.
Serial console
--------------
Opening the case is quite hard, since it is welded together. Rename the
OpenWrt factory image to "test.bin", then plug in the device and quickly
press "2" to enter flash mode (no line feed). Follow the prompts until
OpenWrt is installed.
Unfortunately, this devices does not offer a recovery mode or a tftp
installation method. If the web interface upgrade fails, you have to open
your device and attach serial console.
Additonal notes
---------------
It is possible to flash back to stock by using tplink-safeloader to create
a sysupgrade image based on a stock update. After the first boot, it is
necessary upgrade to another stock image, otherwise subsequent boots
fail with LZMA ERROR 1 and you have to attach serial to recover the device.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
[remove DEVICE_VARS change]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This moves the various variants of common device definitions for
TP-Link devices to a common Makefile common-tp-link.mk. This
provides the opportunity to reorganize and move parameters between
individual device definitions and the common ones.
While at it, also use the common definitions for previously
independent definitions where appropriate.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
DEVICE_PACKAGES is specified twice for the same device. Remove the
first (=older) assignment.
Fixes: 40692f0fb5 ("ramips: mt7620: select only the matching mt76 driver")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The GL.iNet microuter-N300 (internally referred as MT300N-v4) is a
pocket-size travel router. It is essentially identical to the VIXMINI
(internally referred as MT300N-v3) but with double the RAM and
SPI-flash.
Additionally, set the label-mac for both the VIXMINI as well as the
microuter-N300.
Hardware
--------
SoC: MediaTek MT7628NN
RAM: 128M DDR2
FLASH: 16M
LED: Power - WLAN
BTN: Reset
UART: 115200 8N1
TX and RX are labled on the board as pads next to the SoC
Installation via web-interface
------------------------------
1. Visit the web-interface at 192.168.8.1
Note: The ethernet port is by default WAN. So you need to connect to
the router via WiFi
2. Navigate to the Update tab on the left side.
3. Select "Local Update"
4. Upload the OpenWrt sysupgrade image.
Note: Make sure you select not to preserve the configuration.
Installation via U-Boot
-----------------------
1. Hold down the reset button while powering on the device.
Wait for the LED to flash 5 times.
2. Assign yourself a static IPv4 in 192.168.1.0/24
3. Upload the OpenWrt sysupgrade image at 192.168.1.1.
Signed-off-by: David Bauer <mail@david-bauer.net>
In ramips, all devices in mt7621, mt76x8 and rt288x subtarget have
the same value set to the SOC variable for each device individually.
This patch introduces a non-device-dependent variable DEFAULT_SOC,
which is used if no specific SOC is set for a device, and thus reduces
the number of redundant definitions drastically.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Specification:
SoC: MediaTek MT7628AN
RAM: 64MiB
Flash: 8MiB
Wifi:
- 2.4GHz: MT7628AN
- 5GHz: MT7612EN
LAN: 1x 10/100 Mbps
Flash instructions:
Flash factory image through stock firmware WEB UI.
Back to stock is possible by using TFTP and stripping down the Firmware
provided by TP-Link to a initramfs.
The flash space between 0x650000 and 0x7f0000
is blank in the stock firmware so I left it out as well.
Signed-off-by: Steffen Förster <nemesis@chemnitz.freifunk.net>
This device OOPs during the boot due to broken flash. It can be probably
fixed with `broken-flash-reset` once ramips is on 4.19 kernel.
So disable images for this device until its fixed.
Ref: FS#2695, PR#2483
Signed-off-by: Petr Štetiar <ynezz@true.cz>
TP-Link Archer C20 v5 is a router with 5-port FE switch and
non-detachable antennas. It's based on MediaTek MT7628N+MT7610EN.
Specification:
- MediaTek MT7628N/N (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 1T1R 5 GHz
- 5x 10/100 Mbps Ethernet
- 3x external, non-detachable antennas
- UART (J1) header on PCB (115200 8n1)
- 7x LED (GPIO-controlled*), 2x button, power input switch
* WAN LED in this devices is a dual-color, dual-leads type which isn't
(fully) supported by gpio-leds driver. This type of LED requires both
GPIOs state change at the same time to select color or turn it off.
For now, we support/use only the green part of the LED.
Create Factory image
--------------------
As all installation methods require a U-Boot to be integrated into the
Image (and we do not ship one with the image) we are not able to create
an image in the OpenWRT build-process.
Download a TP-Link image from their Website and a OpenWRT sysupgrade
image for the device and build yourself a factory image like following:
TP-Link image: tpl.bin
OpenWRT sysupgrade image: owrt.bin
> dd if=tpl.bin of=boot.bin bs=131584 count=1
> cat owrt.bin >> boot.bin
Installing via Web-UI
---------------------
Upload the boot.bin via TP-Links firmware upgrade tool in the
web-interface.
Installing via Recovery
-----------------------
Activate Web-Recovery by beginning the upgrade Process with a
Firmware-Image from TP-Link. After starting the Firmware Upgrade,
wait ~3 seconds (When update status is switching to 0%), then
disconnect the power supply from the device. Upgrade flag (which
activates Web-Recovery) is written before the OS-image is touched and
removed after write is succesfull, so this procedure should be safe.
Plug the power back in. It will come up in Recovery-Mode on 192.168.0.1.
When active, all LEDs but the WPS LED are off.
Remeber to assign yourself a static IP-address as DHCP is not active in
this mode.
The boot.bin can now be uploaded and flashed using the web-recovery.
Installing via TFTP
-------------------
Prepare an image like following (Filenames from factory image steps
apply here)
> dd if=/dev/zero of=tp_recovery.bin bs=196608 count=1
> dd if=tpl.bin of=tmp.bin bs=131584 count=1
> dd if=tmp.bin of=boot.bin bs=512 skip=1
> cat boot.bin >> tp_recovery.bin
> cat owrt.bin >> tp_recovery.bin
Place tp_recovery.bin in root directory of TFTP server and listen on
192.168.0.66/24.
Connect router LAN ports with your computer and power up the router
while pressing the reset button. The router will download the image via
tftp and after ~1 Minute reboot into OpenWRT.
U-Boot CLI
----------
U-Boot CLI can be activated by holding down '4' on bootup.
Dual U-Boot
-----------
This is TP-Link MediaTek device with a split-uboot feature design like
a TP-Link Archer C50 v4. The first (factory-uboot) provides recovery via
TFTP and HTTP, jumping straight into the second (firmware-uboot) if no
recovery needs to be performed. The firmware-uboot unpacks and executed
the kernel.
Web-Recovery
------------
TP-Link integrated a new Web-Recovery like the one on the Archer C7v4 /
TL-WR1043v5 / Archer C50v4. Stock-firmware sets a flag in the "romfile"
partition before beginning to write and removes it afterwards. If the
router boots with this flag set, bootloader will automatically start
Web-recovery and listens on 192.168.0.1. This way, the vendor-firmware
or an OpenWRT factory image can be written.
By doing the same while performing sysupgrade, we can take advantage of
the Web-recovery in OpenWRT.
It is important to note that Web-Recovery is only based on this flag. It
can't detect e.g. a crashing kernel or other means. Once activated it
won't boot the OS before a recovery action (either via TFTP or HTTP) is
performed. This recovery-mode is indicated by an illuminated WPS-LED on
boot.
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
[adjust some node names for LEDs in DTS]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Image builds for the ramips-mt7621 target currently fail with:
> WARNING: Image file ./hiwifi_hc5962-kernel.bin is too big
Disable this board for now. It can still be built using the SDK.
Signed-off-by: David Bauer <mail@david-bauer.net>
This move the slightly different target-specific implementations of
mktplinkfw from the targets to include/image-commands.mk and renames
it to tplink-v1-image. Having a common version will increase
consistency between implementation and will complete the
tplink build command already present in the new location.
Due to the slight differences of the original implementations, this
also does some adjustments to the device build commands/variables.
This also moves rootfs_align as this is required as dependency.
Tested on:
- TL-WDR4300 v1 (ath79, factory)
- TL-WDR4900 v1 (mpc85xx, sysupgrade)
- RE210 v1 (ramips, see Tested-by)
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Christoph Krapp <achterin@googlemail.com>
ipTIME A8004T is a 2.4/5GHz band AC2600 router, based on Mediatek
MT7621A.
Specifications:
- SoC: MT7621A
- RAM: DDR3 256M
- Flash: SPI NOR 16MB
- WiFi:
- 2.4GHz: MT7615E
- 5GHz: MT7615E
- Ethernet: 5x 10/100/1000Mbps
- Switch: SoC internal
- USB: 1 * USB3.0 port
- UART:
- J4: 3.3V, TX, RX, GND (3.3V is the square pad) / 57600 8N1
- Other info:
- J9: Unknown unpopulated header.
Installation via web interface:
1. Flash **initramfs** image through the stock web interface.
2. Boot into OpenWrt and perform sysupgrade with sysupgrade image.
Revert to stock firmware:
1. Perform sysupgrade with stock image.
Signed-off-by: Yong-hyu Ban <perillamint@quendi.moe>
[do not enable xhci node in DTS which is already enabled in DTSI]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Currently this device fails to boot with the OpenWrt snapshot images
(release images are unaffected). The error message is:
"LZMA ERROR 1 - must RESET board to recover".
This happens because the kernel image is too big for the bootloader
to boot. This commit works around this by decreasing the lzma dictionary
size option from the default 23 to 10.
Before this change the current OpenWrt snapshot image (uncompressed
kernel size 4875139 bytes) failed to boot, while now an even bigger
image (kernel 4.19 with snapshot default config; uncompressed kernel
size 5162833 bytes) boots just fine.
The highest lzma dictionary size option this image booted with was 11.
10 was chosen to have a bit more room for growth.
An unavoidable side-effect of this change is that the compressed kernel
image will take up more space.
Total image size with different dictionary size options:
D23 - 3973903 bytes (base)
D16 - 4113167 bytes (+3.5% - +139264 bytes)
D12 - 4317967 bytes (+8.7% - +344064 bytes)
D11 - 4383503 bytes (+10.3% - +409600 bytes)
D10 - 4461327 bytes (+12.3% - +487424 bytes)
Fixes: FS#1484
Signed-off-by: Mason Clarke <mclarke2355@gmail.com>
Images generated for the TP-Link RE200v1 cannot be updated using
sysupgrade, because a necessary call to append-metadata was missing.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
Edimax RA21S is a dual band 11ac router,
based on MediaTek MT7621A and MT7615N chips.
Specification:
- SoC: MediaTek MT7621A dual-core @ 880MHz
- RAM: 256M (Nanya NT5CC128M16IP)
- FLASH: 16MB (Macronix MX25L12835F)
- WiFi: 2.4/5 GHz 4T4R
- 2.4GHz MediaTek MT7615N bgn
- 5GHz MediaTek MT7615N nac
- Switch: SoC integrated Gigabit Switch (4 x LAN, 1 x WAN)
- USB: No
- BTN: Reset, WPS
- LED: 4 red LEDs, indistinguishable when case closed
- UART: through-hole on PCB.
J1: 3.3V - RX - GND - TX / 57600-8N1. 3.3V is the square pad
Installation:
Update the factory image via the OEM web-interface
(by default: http://192.168.2.1/)
User: admin
Password: 1234
The sysupgrade image can be installed via TFTP
from the U-Boot bootloader. Connect via ethernet port 2.
Tested on device by @UAb5eSMn
Signed-off-by: Maksym Medvedev <redrathnure@gmail.com>
[split DTS and take over improvements from RG21S, extend commit
message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
TP-Link RE200 v1 is a wireless range extender with Ethernet and 2.4G and 5G
WiFi with internal antennas. It's based on MediaTek MT7620A+MT7610EN.
Specifications
--------------
- MediaTek MT7620A (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 1T1R 5 GHz
- 1x 10/100 Mbps Ethernet
- UART header on PCB (57600 8n1)
- 8x LED (GPIO-controlled; only 6 supported), 2x button
There are 2.4G and 5G LEDs in red and green which are controlled
separately. The 5G LED is currently not supported, since the GPIOs couldn't
be determined.
Installation
------------
Web Interface
-------------
It is possible to upgrade to OpenWrt via the web interface. However, the
OEM firmware upgrade file is required and a tool to fix the MD5 sum of
the header. This procedure overwrites U-Boot and there is not failsafe /
recovery mode present! To prepare an image, you need to take the header
and U-Boot (i.e. 0x200 + 0x20000 bytes) from an OEM firmware file and
attach the factory image to it. Then fix the header MD5Sum1.
Serial console
--------------
Opening the case is quite hard, since it is welded together. Rename the
OpenWrt factory image to "test.bin", then plug in the device and quickly
press "2" to enter flash mode (no line feed). Follow the prompts until
OpenWrt is installed.
Unfortunately, this devices does not offer a recovery mode or a tftp
installation method. If the web interface upgrade fails, you have to open
your device and attach serial console. Since the web upgrade overwrites
the boot loader, you might also brick your device.
Additional notes
----------------
MAC address assignment is based on stock-firmware. For me, the device
assigns the MAC on the label to Ethernet and the 2.4G WiFi, while the 5G
WiFi has a separate MAC with +2.
*:88 Ethernet/2.4G label, uboot 0x1fc00, userconfig 0x0158
*:89 unused userconfig 0x0160
*:8A 5G not present in flash
This seems to be the first ramips device with a TP-Link v1 header. The
original firmware has the string "EU" embedded, there might be some region-
checking going on during the firmware upgrade process. The original
firmware also contains U-Boot and thus overwrites the boot loader during
upgrade.
In order to flash back to stock, the first header and U-Boot need to be
stripped from the original firmware.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
This harmonizes the line wrapping in image Makefile device
definitions, as those are frequently copy-pasted and are a common
subject of review comments. Having the treatment unifying should
reduce the cases where adjustment is necessary afterwards.
Harmonization is achieved by consistently (read "strictly")
applying certain rules:
- Never put more than 80 characters into one line
- Fill lines up (do not break after 40 chars because of ...)
- Use one tab for indent after wrapping by "\"
- Only break after pipe "|" for IMAGE variables
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
ipTIME A104ns is a 2.4/5GHz band AC750 router, based on MediaTek MT7620A.
Specifications:
- SoC: MT7620A
- RAM: DDR2 64MB
- Flash: SPI NOR 8MB
- WiFi:
- 2.4GHz: SoC internal
- 5GHz: MT7610EN
- Ethernet: 5x 10/100Mbps
- Switch: SoC internal
- USB: 1x 2.0
- UART:
- J2: 3.3V, TX, RX, GND (3.3V is the square pad) / 57600 8N1
Installation via web interface:
1. Flash **initramfs** image through the stock web interface.
2. Boot into OpenWrt and perform sysupgrade with sysupgrade image.
Revert to stock firmware:
1. Perform sysupgrade with stock image.
In contrast to to-be-supported A1004ns, the A104ns has no usable
value in 0x1fc40 (uboot), so wan_mac needs to be calculated.
Also note that GPIOs for the LEDs really are inverted compared to
the A1004ns.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[moved state_default to device DTS, reordered properties in wmac,
added comment about wan_mac and LED GPIOs]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
JCG JHR-AC876M is an AC2600M router
Hardware specs:
SoC: MT7621AT
2.4GHz: MT7615N 4x4 @ PCIe0
5GHz: MT7615N 4x4 @ PCIe1
Flash: Winbond W25Q128JVSQ 16MiB
RAM: Nanya NT5CB128M16 256MiB
USB 2.0 and 3.0 ports
6 LEDs, 3 of which are connected to SoC GPIO
Reset and WPS buttons
Flash instructions:
Stock to OpenWrt:
Upload factory.bin in stock firmware's upgrade page,
do not preserve settings
OpenWrt to stock:
Push and hold the reset button for 5s while power cycling to
enter recovery mode;
Visit 192.168.1.1 and upload stock firmware
MAC addresses map:
0x0004 *:1c wlan2g/wan/label
0x8004 *:20 wlan5g
0xe000 *:1b lan
0xe006 *:1a not used in stock fw
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
This allows JCG_MAXSIZE to be specified in kilobytes. This makes
this value more consistent and easier comparable with other size
variables.
This also changes the only occurence of the variable, for Cudy WR1000.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
ipTIME A6ns-M is a 2.4/5GHz band AC1900 router, based on MediaTek MT7621A.
Specifications:
- SoC: MT7621AT
- RAM: DDR3 128MB
- Flash: SPI NOR 16MB
- WiFi:
- 2.4GHz: MT7615
- 5GHz: MT7615
- Ethernet: 5x 10/100/1000Mbps
- Switch: SoC internal
- UART:
- J4: 3.3V, TX, RX, GND (3.3V is the square pad) / 57600 8N1
Installation via web interface:
1. Flash **initramfs** image through the stock web interface.
2. Boot into OpenWrt and perform sysupgrade with sysupgrade image.
Revert to stock firmware:
1. Perform sysupgrade with stock image.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
ZIO FREEZIO is a 2.4/5GHz band AC1200 router, based on MediaTek MT7621A.
Specifications:
- SoC: MT7621AT
- RAM: DDR3 128MB
- Flash: SPI NOR 16MB
- WiFi:
- 2.4GHz: MT7603EN
- 5GHz: MT7612EN
- Ethernet: 5x 10/100/1000Mbps
- Switch: SoC internal
- USB: 1x 3.0
- UART:
- J4: 3.3V, RX, TX, GND (3.3V is the square pad) / 57600 8N1
Notes:
- FREEZIO has almost the same board as WeVO W2914NS v2.
- Stock firmware is based on OpenWrt BB.
MAC addresses in factory partition:
0x0004: WiFi 2.4GHz (label_mac-8)
0x002e: WAN (label_mac)
0x8004: WiFi 5GHz (label_mac-4)
0xe000: LAN (label_mac+1)
Installation via web interface:
1. Access web admin page and turn on "OpenWrt UI mode".
2. Flash sysupgrade image through LuCI, with the "Keep settings" option
OFF.
Revert to stock firmware:
1. Perform sysupgrade with stock image.
Make sure to NOT preserve settings.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[rebase, use mt7621_wevo_w2914ns-v2.dtsi]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The DTS variable has been removed in 402138d12d ("ramips: Derive
DTS name from device name in Makefile"), but the DEVICE_VARS entry
has been overlooked.
Remove it now since we are not using this variable.
This must _not_ be backported to 19.07, where the variable is still
in use.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The stock firmware and bootloader only accept uImage with names that
match certain patterns. This patch enables OpenWrt installation from
stock firmware without having to reflash the bootloader or access the
UART console.
Installation via web interface:
1. Flash **initramfs** image through the stock web interface.
2. Boot into OpenWrt and perform sysupgrade with sysupgrade image.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
ALFA Network Quad-E4G is a universal Wi-Fi/4G platform, which offers
three miniPCIe (PCIe, USB 2.0, SIM) and a single M.2 B-key (dual-SIM,
USB 3.0) slots, RTC and five Gigabit Ethernet ports with PoE support.
Specification:
- MT7621A (880 MHz)
- 256/512 MB of RAM (DDR3)
- 16/32+ MB of FLASH (SPI NOR)
- optional second SPI flash (8-pin WSON/SOIC)
- 1x microSD (SDXC) flash card reader
- 5x 10/100/100 Mbps Ethernet, with passive PoE support (24 V) in LAN1
- optional 802.3at/af PoE module for WAN
- 3x miniPCIe slot (with PCIe and USB 2.0 buses, micro SIM and 5 V)
- 1x M.2/NGFF B-key 3042 (USB 3.0/2.0, mini + micro SIM)
- RTC (TI BQ32002, I2C bus) with backup battery (CR2032)
- external hardware watchdog (EM Microelectronic EM6324)
- 1x USB 2.0 Type-A
- 1x micro USB Type-B for system serial console (Holtek HT42B534)
- 11x LED (5 for Ethernet, 5 driven by GPIO, 1x power indicator)
- 3x button (reset, user1, user2)
- 1x I2C (4-pin, 2.54 mm pitch) header on PCB
- 4x SIM (6-pin, 2.00 mm pitch) headers on PCB
- 2x UART2/3 (4-pin, 2.54 mm pitch) headers on PCB
- 1x mechanical power switch
- 1x DC jack with lock (24 V)
Other:
- U-Boot selects default SIM slot, based on value of 'default_sim' env
variable: '1' or unset -> SIM1 (mini), '2' -> SIM2 (micro). This board
has additional logic circuit for M.2 SIM switching. The 'sim-select'
will work only if both SIM slots are occupied. Otherwise, always slot
with SIM inside is selected, no matter 'sim-select' value.
- U-Boot enables power in all three miniPCIe and M.2 slots before
loading the kernel
- this board supports 'dual image' feature (controlled by 'dual_image'
U-Boot environment variable)
- all three miniPCIe slots have additional 5 V supply on pins 47 and 49
- the board allows to install up to two oversized miniPCIe cards (vendor
has dedicated MediaTek MT7615N/D cards for this board)
- this board has additional logic circuit controlling PERSTn pins inside
miniPCIe slots. By default, PERSTn (GPIO19) is routed to all miniPCIe
slots but setting GPIO22 to high allows PERSTn control per slot, using
GPIO23-25 (value is inverted)
You can use the 'sysupgrade' image directly in vendor firmware which is
based on OpenWrt (make sure to not preserve settings - use 'sysupgrade
-n -F ...' command). Alternatively, use web recovery mode in U-Boot:
1. Power the device with reset button pressed, the modem LED will start
blinking slowly and after ~3 seconds, when it starts blinking faster,
you can release the button.
2. Setup static IP 192.168.1.2/24 on your PC.
3. Go to 192.168.1.1 in browser and upload 'sysupgrade' image.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
ALFA Network R36M-E4G is a dual-SIM, N300 Wi-Fi, compact size platform
based on MediaTek MT7620A WiSoC. This product is designed for operation
with 4G modem (can be bought in bundle with Quectel EC25, EG25 or EP06)
but supports also Wi-Fi modules (miniPCIe slot has USB and PCIe buses).
Specification:
- MT7620A (580 MHz)
- 64/128/256 MB of RAM (DDR2)
- 16/32+ MB of FLASH (SPI NOR)
- 2x 10/100 Mbps Ethernet, with passive PoE support (24 V)
- 2T2R 2.4 GHz (MT7620A), with ext. LNA (RFFM4227)
- 1x miniPCIe slot (with PCIe and USB 2.0 buses and optional 5 V)
- 2x SIM slot (mini, micro) with detect and switch driven by GPIO
- 2x u.fl antenna connectors (for Wi-Fi)
- 8x LED (7 driven by GPIO)
- 2x button (reset, wifi)
- 2x UART (4-pin/2.54 mm pitch, 10-pin/1.27 mm pitch) headers on PCB
- 1x I2C (4-pin, 1.27 mm pitch) header on PCB
- 1x LED (8-pin, 1.27 mm pitch) header on PCB
- 1x DC jack with lock (12 V)
Other:
- there is a dedicated, 4-pin connector for optional RTC module (Holtek
HT138x) with 'enable' input, not available at the time of preparing
support for this board
- miniPCIe slot supports additional 5 V supply on pins 47 and 49 but a
jumper resistor (R174) is not installed by default
- U-Boot selects default SIM slot, based on value of 'default_sim' env
variable: '1' or unset -> SIM1 (mini), '2' -> SIM2 (micro). This will
work only if both slots are occupied, otherwise U-Boot will always
select slot with SIM card inside (user can override it later, in
user-space)
- U-Boot resets the modem, using PERSTn signal, before starting kernel
- this board supports 'dual image' feature (controlled by 'dual_image'
U-Boot environment variable)
Flash instruction:
You can use the 'sysupgrade' image directly in vendor firmware which is
based on OpenWrt (make sure to not preserve settings - use 'sysupgrade
-n -F ...' command). Alternatively, use web recovery mode in U-Boot:
1. Power the device with reset button pressed, the modem LED will start
blinking slowly and after ~3 seconds, when it starts blinking faster,
you can release the button.
2. Setup static IP 192.168.1.2/24 on your PC.
3. Go to 192.168.1.1 in browser and upload 'sysupgrade' image.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
CY-SWR1100 has a USB LED but kmod-usb-ledtrig-usbport is missing
in default images. This commit adds it.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[changed commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Specifications:
* SoC: MT7620A
* RAM: 64 MB DDR
* Flash: 8MB NOR SPI flash
* WiFi: MT7612E (5Ghz) and builtin MT7620A (2.4GHz)
* LAN: 1x100M
The -factory images can be flashed from the
device's web interface or via nmrpflash.
The device seems to use base PCB as EX3700/EX3800,
but supporting AC1200 using MT7612E.
MAC adresses:
5.0 GHz 0x8004 *:9a
2.4 GHz 0x4 *:9b
lan 0x28 *:9b
wan 0x2e *:9c
Since this is a one-port device, although wan MAC address is
set in flash, it is not used in OpenWrt setup.
Signed-off-by: Frederik Noe-Sdun <Frederik.Sdun@googlemail.com>
[rebased, extended commit message, tiny DTS style fixes]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The elecom-header renames the firmware image to v_0.0.0.bin, stores its
MD5 sum as v_0.0.0.md5 and tars both files again.
Both v_0.0.0 files are created as the build user making it harder to
reproduce.
This commit sets the owner/group of both files to root by adding extra
options to the final tar command.
Before:
0 buildbot (101) buildbot (102) 3932164 2019-11-05 14:43:22.000000 v_0.0.0.bin
0 buildbot (101) buildbot (102) 33 2019-11-05 14:43:22.000000 v_0.0.0.md5
After:
0 root (0) root (0) 3932164 2019-11-05 23:43:08.000000 v_0.0.0.bin
0 root (0) root (0) 33 2019-11-05 23:43:08.000000 v_0.0.0.md5
Signed-off-by: Paul Spooren <mail@aparcar.org>
rt3883.mk contains both RT3662 and RT3883 device profiles, but commit
6a104ac772 set MTK_SOC to rt3883 for all devices. This patch fixes it,
and renames dts files accordingly. And SoC compatible strings are also
appended in the dts.
Fixes: 6a104ac772 ("ramips/rt288x,rt3883: Name DTS files based on scheme")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
This commit adds support for the ZBT WE1026-H, an outdoor AP with
support for adding an internal LTE modem. The detailed specs are:
* CPU: MT7620A
* 2x 10/100Mbps Ethernet (LAN port has passive PoE support).
* 16/32 MB Flash.
* 128/256 MB RAM.
* 1x USB 2.0 port.
* 1x mini-PCIe slot (only USB2.0 bus).
* 1x SIM slot (standard size).
* 1x 2.4Ghz WIFI (rt2800).
* 1x button.
* 6x LEDS (4 GPIO-controlled).
* 1x micro-SD reader.
The following have been tested and working:
- Ethernet switch
- Wifi
- Mini-PCIe slot + SIM slot
- USB port
- microSD slot
- sysupgrade
- reset button
Installation and recovery:
In order to install OpenWRT the first time or ito recover the router,
you can use the web-based recovery system. Keep the reset button pressed
during boot and access 192.168.1.1 in your browser when your machine
obtains an IP address. Upload the firmware to start the recovery
process.
Notes:
* When binding the USB LED to a usbport, the LED is switched on all the
time due to the presence of an internal hub. Thus, it does not really
signal any USB-information.
* I only have the 32MB version and have only added support for this
device. However, the files are structured so that adding support for the
16MB version should be easy.
* Only the LAN port is accessible from the outside of the casing and LEDs
are not visible.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
[rebased onto base-files split, minor style fixes, removed use of
USB led as power LED]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch renames and reassembles the common definition for
Netgear R6xxx devices in mt7621.mk. The following goals should be
achieved:
- Give the node a more generic name instead of adding devices to it
- Use the common definition in the (less) similar R6220 node
- Include/exclude settings into the common definition so the common
node contains the common definitions
- Prepare for support of R6700 v2
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
- CMIIT ID: 2019AP2581
- SoC: MediaTek MT7621
- Flash: 16MiB NOR SPI (GigaDevice GD25Q128B)
- RAM: 128MiB DDR3 (ESMT M15T1G1664A)
- Serial: As marked on PCB, 3V3 logic, baudrate is 115200, 8n1
- Ethernet: 3x 10/100/1000 Mbps (switched, 2xLAN + WAN)
- WIFI0: MT7603E 2.4GHz 802.11b/g/n
- WIFI1: MT7612E 5GHz 802.11ac
- Antennas: 4x external (2 per radio), non-detachable
- LEDs: Programmable "power" LED (two-coloured, yellow/blue)
Non-programmable "internet" LED (shows WAN activity)
- Buttons: Reset
INSTALLATION:
Bootloader won't accept any serial input unless "boot_wait" u-boot
environment variable is changed to "on". Vendor firmware (looks like
an illegal OpenWrt fork) won't accept any serial input unless
"uart_en" is set to "1". Tricks to force u-boot to use default
environment do not help as it's restricted in the same way.
With bootloader unlocked the easiest way would be to TFTP the
sysupgrade image or to sysupgrade after loading an initramfs one.
For porting the flash contents were changed externally with an SPI
programmer (after lifting Vcc flash IC pin away from the PCB).
Forum thread [0] indicates that this device is identical to "Xiaomi Mi
Router 4A Gigabit Edition".
[0] https://forum.openwrt.org/t/xiaomi-mi-router-4a-gigabit-edition-r4ag-r4a-gigabit-fully-supported-but-requires-overwriting-spi-flash-with-programmer/36685
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
The Asus RT-AC65P router is identical with the RT-AC85P, but better to make separate images for it.
On both routers the installation can be done also via SSH:
Note: The user/password for SSH is identical with the one used in the
Web-interface.
1. Complete the initial setup wizard.
2. Activate SSH under "Administration" -> "System".
3. Transfer the OpenWrt factory image via scp:
> scp openwrt-ramips-mt7621-asus_rt-ac65p-squashfs-factory.bin admin@192.168.50.1:/tmp
4. Connect via SSH to the router.
> ssh admin@192.168.50.1
5. Write the OpenWrt image to flash.
> mtd-write -i
/tmp/openwrt-ramips-mt7621-asus_rt-ac65p-squashfs-factory.bin -d linux
6. Reboot the router
> reboot
Changelog:
v3: removed [] from filename, rebased to latest master
v2: Rebased to latest master
v1: Initial release
Signed-off-by: Gabor Varga <vargagab@gmail.com>
Device node names were updated, but updating TARGET_DEVICES
was overlooked.
Fixes: 4408723d42 ("ramips: remove RAM size from device name
for UniElec devices")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
UniElec devices are the last ones in ramips target still having
the RAM size in device name although RAM size is auto-detected.
Remove this from device name, compatible, etc., as it's not
required and might be misleading to users and developers adding
device support copying those devices.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The Phicomm KE 2P is identical to the already supported Phicomm K2P,
renamed for the European market. Use the ALT0 buildroot tags to show
both devices.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
This removes _all_ occurrences of kmod-usb-core from
DEVICE_PACKAGES and similar variables.
This package is pulled as dependency by one of the following
packages in any case:
- kmod-usb-chipidea
- kmod-usb-dwc2
- kmod-usb-ledtrig-usbport
- kmod-usb-ohci
- kmod-usb2
- kmod-usb2-pci
- kmod-usb3
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[remove kmod-usb-core from EnGenius ESR600]
Signed-off-by: David Bauer <mail@david-bauer.net>
All Zbtlink ramips devices except the ZBT-WE1026-5G include the
zbt-/ZBT- prefix in their model name.
This changes ZBT-WE1026-5G to also follow that scheme.
The patch moves some block to keep alphatical order.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Spelling of Zbtlink varies across image definitions and DTS files.
This patch uses Zbtlink consistently and also updates the model
in DTS files to contain the vendor in all cases.
This patch is cosmetical, as there should be no dependencies on
device model name in ramips anymore.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
I-O DATA WNPR2600G has an "elx-header", so move this definition to
generic makefile to use it from mt7621 subtarget.
This definition is also added to mt7621.mk in
f285e8634c, so remove it from mt7621.mk.
And added a line to cleanup used header file.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
ipTIME A3 is a 2.4/5GHz band AC1200 router, based on MediaTek
MT7628AN.
Specifications:
- SoC: MT7628AN
- RAM: DDR2 64MB
- Flash: SPI NOR 8MB
- WiFi:
- 2.4GHz: SoC internal
- 5GHz: MT7612EN
- Ethernet: 3x 10/100Mbps
- Switch: SoC internal
- UART:
- J1: 3.3V, TX, RX, GND (3.3V is the square pad) / 57600 8N1
Installation via web interface:
1. Flash **initramfs** image through the stock web interface.
2. Boot into OpenWrt and perform sysupgrade with sysupgrade image.
Revert to stock firmware:
1. Perform sysupgrade with stock image.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Hardware:
SoC: MT7621A
Flash: 32 MiB
RAM: 512 MiB
Ethernet: built-in switch
USB: 1x USB3.0
SATA: ASM1060, 1 SATA port
Flash instruction (TFTP):
1. Set PC to fixed ip address 192.168.173.22
2. Download *-sysupgrade.bin image and rename it to firmware.img
3. Start a tftp server with the image file in its root directory
4. Turn off the router
5. Turn on router,press the reset button and wait ~15 seconds
6. Release the reset button and after a short time
the firmware should be transferred from the tftp server
7. Wait ~3 minutes to complete recovery.
Signed-off-by: Qi Jiang <rushx@live.cn>
[squash commits, add label-mac-device, fix sign-off style]
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
