Change u-boot-env partitions to be mounted as read-write for gl-ar150,
gl-domino and gl-mifi so uboot-envtools support is possible.
Signed-off-by: Kimmo Vuorinen <kimmo.vuorinen@gmail.com>
[commit title/message facelift]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This moves the TP-Link TL-WA850RE v2 to dynamic partitioning and
will allow to use this for ath79 as well.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
When mapping for RSSI LEDs was defined for interface wlan0 on
Ubiquiti Rocket M Titanium, it missed connection to actual interface.
Therefore create the mapping to interface, so RSSI LEDs work without
additional configuration, after starting rssileds service.
While at that, split RSSI into ~equal intervals for 6 LEDs,
and remove coefficients needed for PWM LEDs, as this board does not
support PWM LEDs.
Finally, for complete support, enable 'rssileds' package in per-device
rootfs, so the indicator works out of box.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
This image is only needed on one device (wAP AC); since this target is
going to be removed anyway it doesn't make sense to add an extra "low
RAM" image.
Fixes OOM issues on RouterBoard wAP AC.
Signed-off-by: Thomas Nixon <tom@tomn.co.uk>
Currently the patch only changes break to use goto statement instead.
But not necessary acutually since the ret value checked after the for loop.
So it is okay for the break case before changed by the patch also.
This patch only reverts the following commit partially.
ddc11c3932
Note: The changes are mainly applied into the linux kernel upstream.
Signed-off-by: Tokunori Ikegami <ikegami.t@gmail.com>
Cc: Koen Vandeputte <koen.vandeputte@ncentric.com>
The current ethernet MAC address setup of TL-WDR4300 board is different
from the setup of stock firmware:
OpenWrt: lan = label_mac -2, wan = label_mac -2
stock: lan = label_mac, wan = label_mac +1
This patch applies to all devices using TL-WDR4300 board:
TL-WDR3600 v1
TL-WDR4300 v1
TL-WDR4300 v1 (IL)
TL-WDR4310 v1
Mercury MW4530R v1
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
This enables the system LED to indicate a running firmware upgrade. This
pattern is used on most platforms provided by the generic base-files
package. ar71xx uses it's own implementation for the system-LED, where
the upgrade case is not yet implemented.
Signed-off-by: David Bauer <mail@david-bauer.net>
In order to make RSSI indicator on the device work out of box,
include "rssileds" package in per-device rootfs image by default
for Ubiquiti XM and XW devices, namely:
- Bullet M (XM/XW)
- Rocket M (XM/XW)
- Nanostation M (XM/XW)
- Nanostation Loco-M (XW)
This moves the package addition to the individual devices in order
to prevent accidental inclusions of the package when not looking
at the parent node carefully enough.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
[add bullet-m-xw, remove rocket-m-ti, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
TP-Link TL-WDR4900 v2 only has one combined WPS/Reset button, so
don't set up an RFKILL for this device.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
In ar71xx there is only one combined mach file for Archer C5/C7 and
TL-WDR4900 v2. This one uses the same LED struct for all devices,
defining "green" LEDs for them. However, WDR4900 uses blue front
LEDs, while only C5/C7 uses green ones. Despite, in base-files
WDR4900 is actually set up with "blue" for the mentioned LEDs.
Thus, this patch creates a separate LED struct for WDR4900, so the
LEDs can be set up correctly. Despite, the wlan5g LED is removed as
it is controlled by ath9k chip for WDR4900 (in contrast to C5/C7).
Note: While front LEDs are blue, USB LEDs (on the back) are green,
so colors are mixed intentionally for the WDR4900 v2.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The MAC address setup of the TL-WDR4900 v2 is different from the
C5/C7. This aligns ar71xx with the setup in ath79:
wlan0 (5GHz) : -2
wlan1 (2.4GHz) : -1
eth1 (LAN) : 0
eth0 (WAN) : 1
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
As discussed in 1d18a14a90 ("ath79: really fix TP-Link Archer C7
v2 MAC address"), stock firmware MAC address assignment is
actually as follows:
wlan0 (5GHz) : -1
wlan1 (2.4GHz) : 0
eth1 (LAN) : 0
eth0 (WAN) : 1
This has never been fixed for ar71xx, so let's do it now.
Note that with WDR4900 v2 even both wlan0 and wlan1 where assigned
to basemac-1 before ...
Fixes: FS#408
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Fix the error that tl-wdr3320-v2 can't upgrade firmware via web
interface by using magic_ver="0200" for this device.
Signed-off-by: 南浦月 <nanpuyue@gmail.com>
[commit message facelift]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This commit adds correct model detection for UniFi
AC-LR. Previously, said device was incorrectly detected
as UniFi-AC-LITE/MESH.
The Information about the device is stored at 0xC in the EEPROM
partition. It corresponds to the sysid in /etc/board.info of the
Ubiquiti stock firmware.
Signed-off-by: Andreas Ziegler <dev@andreas-ziegler.de>
[adjust naming style of target to existing ones]
Signed-off-by: David Bauer <mail@david-bauer.net>
This fixes commit bae927c551 ("ar71xx: add support for TP-LINK CPE510
V2.0") where the support for this device wasn't optimal.
Device support for the CPE510v2 so far has been a hack to enable
flashing with CPE510v1 images. Those even have different hardware (e.g.
additional ethernet port).
With this patch, we provide proper support for this device in ar71xx.
Installation:
- Flash factory image through stock firmware WEB UI or through TFTP
- To get to TFTP recovery just hold reset button while powering on
for around 4-5 seconds and release.
- Rename factory image to recovery.bin
- Stock TFTP server IP: 192.168.0.100
- Stock device TFTP address: 192.168.0.254
Fixes: bae927c551 ("ar71xx: add support for TP-LINK CPE510 V2.0")
Signed-off-by: Andrew Cameron <apcameron@softhome.net>
[Rebased onto revert commit, changed comments in mach-cpe510.c,
changed commit title and description, fixed eth0 MAC address,
removed eth1 initialization]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[squashed revert, added fixes tag]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Change WAN LED behaviour to be consistent with other Netgear
routers running OpenWrt. Instead of link speed, use amber colour
to indicate link status. Green LED should be used when Internet
connection is up and running.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
GPIO key labels have been changed to standard ones (rfkill, reset, wps).
It does not affect button functionality.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
This removes _all_ occurrences of kmod-usb-core from
DEVICE_PACKAGES and similar variables.
This package is pulled as dependency by one of the following
packages in any case:
- kmod-usb-chipidea
- kmod-usb-dwc2
- kmod-usb-ledtrig-usbport
- kmod-usb-ohci
- kmod-usb2
- kmod-usb2-pci
- kmod-usb3
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[remove kmod-usb-core from EnGenius ESR600]
Signed-off-by: David Bauer <mail@david-bauer.net>
Move the IRQ fix from generic to ar71xx specific.
Other targets like ath79 have specific pathes to delete this code.
This resulted in a build failure on ath79
While at it, wipe the 4.19 version, as ar71xx will never reach this.
Fixes: 530f76708cef ("ar71xx: Fix potentially missed IRQ handling during
dispatch")
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
If both interrupts are set in the current implementation
only the 1st will be handled and the 2nd will be skipped
due to the "if else" condition.
Fix this by using the same approach as done for QCA955x
just below it.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
This reverts commit 5b98061bb1.
As Piotr Dymacz pointed out:
In QCA MIPS based WiSOCs, for first USB interface,
device/host mode can be selected _only_ in hardware
see description of 57c641ba6e
QCA955x and QCA9563, second USB can be switched to device
mode in software (tested and confirmed on real hardware).
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Current ar724x code does the reset only on single pci bus, and
in case of qca9558 writes the wrong register (0x10 vs 0x0c).
This change allows the reset of second pci bus, commonly used in
Archer C7 devices, in case host controller is stuck in reset.
If the resetting controller on boot can solve any other issue it
can be enabled unconditionally by removing reset check before
ar724x_pci_hw_init is called.
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
[refreshed to apply cleanly]
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Enable flushing of write buffers on qca955x. GPL code has 0x88 reg
defined for PCI flush which is likely an error since the device
freezes on boot. So use DS default value 0xA8 for PCI flush.
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
Now that $UPGRADE_BACKUP is set conditionally there is no need to check
the $UPGRADE_OPT_SAVE_CONFIG anymore. All conditions can be simplified.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
It's a variable set by procd that should replace hardcoded
/tmp/sysupgrade.tgz.
This change requires the most recent procd with the commit 0f3c136
("sysupgrade: set UPGRADE_BACKUP env variable").
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
That was a result of accidentally running "sed" twice on some files.
Fixes: 5797fe84a3 ("treewide: replace remaining (not working now) $SAVE_CONFIG uses")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This var has been replaced by the $UPGRADE_OPT_UPGRADE_OPT_SAVE_CONFIG
Fixes: b534ba9611 ("base-files: pass "save_config" option to the "sysupgrade" method")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
There is md5 sum of whole image embedded in combined-image header which
is checked on sysupgrade. The check will fail for ath79 images which
may have embedded metadata. This is because metadata are appended after
the combined image is created. To allow smooth transition from ar71xx to
ath79, strip metadata before calculating md5 sum for whole image.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Without this patch, an extra entry appears for AR9287 GPIO
that duplicates WLAN LED but in fact drives nothing:
gpiochip1: GPIOs 502-511, ath9k-phy0:
gpio-502 ( |netgear:blue:wlan ) out hi
gpio-503 ( |netgear:amber:test ) out hi
gpio-504 ( |netgear:green:power ) out lo
gpio-505 ( |rfkill ) in hi
gpio-507 ( |wps ) in hi
gpio-508 ( |reset ) in hi
gpio-510 ( |ath9k-phy0 ) out hi <===!
The pin pointed above is default LED GPIO (8) for AR9287.
For WNR2200 it is not connected anywhere - pin 0 drives blue WLAN
LED instead - but initialization code is missing that information.
This fix calls ap9x_pci_setup_wmac_led_pin() function at device
setup, forcing WLAN LED pin to be 0 and removing redundant entry.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
tx_size was just declared above and set to BIT(tx->order)
Use the declaration instead, which could avoid a pointer deref
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Backport of a4eef43a12 ("ath79: ag71xx: replace alloc_etherdev with devm_alloc_etherdev")
combined with the initial changes from John Crispin.
Simplifies the code a lot by using the Managed dev API.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Backport of 4eaa3626a8 ("ath79: ag71xx: pass correct device pointer to dma functions")
While 4.14 does not contain the warnings,
it still makes sense to use the proper pointers here.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
All other instances of this identical declaration fetch the
value directly from the ring_order.
Also do it here.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
This changes size and offset set for WiFi caldata extraction and
MAC address adjustment to hexadecimal notation.
This will be much clearer for the reader when numbers are big, and
will also match the style used for mtd-cal-data in DTS files.
Since dd cannot deal with hexadecimal notation, one has to convert
back to decimal by simple $(($hexnum)).
Acked-by: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
