Commit Graph

9 Commits

Author SHA1 Message Date
Daniel Golle
4cb6bd9a6d mediatek: switch to pending XFI 10G Ethernet drivers
Replace previous patch adding paths and SerDes modes with patch series
pending upstream adding dedicated drivers for XFI T-PHY and USXGMII PCS,
extends LynxI PCS to be a standalone platform driver and as a consequence
makes much less changes to the actual Ethernet driver mtk_eth_soc.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-02-15 19:06:36 +00:00
Daniel Golle
c36de2e73a mediatek: backport a hell of thermal commits
Backport almost 50 commits from upstream Linux to improve thermal
drivers for MediaTek SoCs and add new LVTS driver for MT7988.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-02-15 19:06:36 +00:00
Chukun Pan
3a3a4d3bd3 mediatek: filogic: refresh kernel config
Refresh kernel config with 'make kernel_oldconfig'.
Also disable the useless rtl8367s gsw driver.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2024-01-14 23:11:57 +00:00
Daniel Golle
a270f61c00 mediatek: import driver for Adtran SmartRG RGBW LED
Import driver for I2C-connected HolTek MCU controlling the RGBW LED
found in Adtran SmartRG devices.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-12-10 06:22:51 +00:00
Daniel Golle
c8c2f52262 mediatek: add support for Zbtlink ZBT-Z8102AX
Specifications:
SoC: MediaTek MT7981B
RAM: 1024MiB
Flash: SPI-NAND 128 MiB
Switch: 1 WAN, 4 LAN (Gigabit)
USB: two M.2 slots for 5G modems via USB 3.0 hub, external USB 3.0 port
Buttons: Reset, Mesh
Power: DC 12V 1A
WiFi: MT7976CN
UART: 115200n8
UART Layout:
VCC-RX-TX-GND

Installation:
A. Through OpenWrt Dashboard:
If your router comes with OpenWrt preinstalled (modified by the seller),
you can easily upgrade by going to the dashboard (192.168.1.1) and then
navigate to System -> Backup/Flash firmware, then flash the firmware

B. Through TFTP
Standard installation via UART:

1. Connect USB Serial Adapter to the UART, (NOTE: Don't connect the VCC pin).
2. Power on the router. Make sure that you can access your router via UART.
3. Restart the router then repeatedly press ctrl + c to skip default boot.
4. Type > bootmenu
5. Press '2' to select upgrade firmware
6. Press 'Y' on 'Run image after upgrading?'
7. Press '0' and hit 'enter' to select TFTP client (default)
8. Fill the U-Boot's IP address and TFTP server's IP address.
9. Finally, enter the 'firmware' filename.

Based on patch adding support for similar Zbtlink ZBT-Z8103AX device by
Ian Ishmael C. Oderon.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-11-24 21:28:35 +00:00
Daniel Golle
f631c7bbb1 generic: sync MediaTek Ethernet driver with upstream
Import commits from upstream Linux replacing some downstream patches.
Move accepted patches from pending-{5.15,6.1} to backport-{5.15,6.1}.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-08-28 16:35:22 +01:00
Daniel Golle
dc4aafb309 mediatek: filogic: enable driver for MediaTek XS-PHY
Enable driver for MediaTek SuperSpeedPlus XS-PHY transceiver for the
USB3.1 GEN2 controllers found in the MT7988 SoC.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-07-31 18:05:22 +01:00
Daniel Golle
30d38d7541 mediatek: adapt kernel configuration for Linux 6.1
Update kernel configuration to build Linux 6.1 for all subtargets.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-07-07 14:01:39 +02:00
Daniel Golle
775fd1fc85 mediatek: copy config-5.15 to config-6.1 for all subtargets
To ease review, first copy all subtargets' kernel config-5.15 to the
to-be-adapted config-6.1.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-07-07 14:01:39 +02:00