The "/dts-v1/;" identifier is supposed to be present once at the
top of a device tree file after the includes have been processed.
In ath79, we therefore requested to have in the DTS files so far,
and omit it in the DTSI files. However, essentially the syntax of
the parent ath79.dtsi file already determines the DTS version, so
putting it into the DTS files is just a useless repetition.
Consequently, this patch puts the dts-v1 statement into the parent
ath79.dtsi, which is (indirectly) included by all DTS files. All
other occurences are removed.
Since the dts-v1 statement needs to be before any other definitions,
this also moves the includes to make sure the ath79.dtsi or its
descendants are always included first.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This harmonizes the model names for the ath79 Ubiquiti devices by
applying a few minor cosmetic adjustments:
- Removes hyphens where they are not found in the product names
(Ubiquiti uses hyphens only for the abbreviated version names
like UAP-AC-PRO which we don't use anyway.)
- Add (XM) suffix for DTS model strings to help with distinguishing
them from their XW counterparts.
- Remove DEVICE_VARIANT for LAP-120 which actually was an alternate
device name.
- Generally make DTS model names and those from generic-ubnt.mk
more consistent.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* Prepare to support the AR7240 variant of ubiquiti bullet m, by
reorganizing the related dtsi files.
* Distribute SOC variable across ubnt-xm devices.
Signed-off-by: Russell Senior <russell@personaltelco.net>
This adds support for the Ubiquiti Nanostation Loco M (XM), which
has the same board/LEDs as the Bullet M XM, but different case and
antennas.
Specifications:
- AR7241 SoC @ 400 MHz
- 32 MB RAM
- 8 MB SPI flash
- 1x 10/100 Mbps Ethernet, 24 Vdc PoE-in
- NS Loco M2: built-in antenna: 8 dBi; AR9287
- NS Loco M5: built-in antenna: 13 dBi; 2T2R 5 GHz radio
- POWER/LAN green LEDs
- 4x RSSI LEDs (red, orange, green, green)
- UART (115200 8N1) on PCB
Flashing via WebUI:
Upload the factory image via the stock firmware web UI.
Note that only certain firmware versions accept unsigned
images. Refer to the device's Wiki page for further information.
Flashing via TFTP:
Same procedure as other NanoStation M boards.
- Use a pointy tool (e.g., pen cap, paper clip) and keep the reset
button on the device or on the PoE supply pressed
- Power on the device via PoE (keep reset button pressed)
- Keep pressing until LEDs flash alternatively LED1+LED3 =>
LED2+LED4 => LED1+LED3, etc.
- Release reset button
- The device starts a TFTP server at 192.168.1.20
- Set a static IP on the computer (e.g., 192.168.1.21/24)
- Upload via tftp the factory image:
$ tftp 192.168.1.20
tftp> bin
tftp> trace
tftp> put openwrt-ath79-generic-xxxxx-ubnt_nanostation-loco-m-squashfs-factory.bin
Tested on NanoStation Loco M2.
Signed-off-by: Sven Roederer <freifunk@it-solutions.geroedel.de>
Co-developed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
