According to the datasheet the REFCLK pin is shared with GPIO#37 and
the PERST pin is shared with GPIO#36.
While at it fix a typo inside the pinmux setup code. The function is called
refclk and not reclk.
Update device tree source files accordingly.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This commit adds missing the GPIO key used as reset button.
Nexx WT1520 has a GPIO key for factory reset, but it's not defined in
WT1520.dtsi and cannot use it.
Drop the UART (full) from the device tree source file, it was never
used for this board. Adjust the kernel bootargs accordingly.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[add note about dropped UART (full) to the commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Add kmod-sound-core, it is a dependency of kmod-sound-mt7620 and will
not be autoselected.
Remove kmod-i2c-core, it will be autoselected by kmod-i2c-ralink.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Setting the pins of the uartf group to gpio+i2s at the time the i2c
driver loads is to late for the WPS gpio button.
The gpio-keys driver fails to load since the pin used by the WPS button
is not yet set to GPIO. The WPS button with the rfkill keycode is
essential for this wifi only board.
Add the missing sound and i2c kernel modules corresponding to the
device nodes.
Signed-off-by: Mathias Kresin <dev@kresin.me>
D-Link DIR-330 is clone of ASUS WL500GP2, by default conf the WAN port is
eth1, it's not working cus eth1 not soldered and wan port function
performs 5th port of the switch.
Signed-off-by: Antony Black <gtrtfm@gmail.com>
On Asus RT-N12 and RT-N16 models, the WAN and LAN4 ports are swapped in the
initial switch configuration since the presets present in nvram appear to be
wrong.
Add special casing for these models to detect_by_model() in order to ensure
a proper switch configuration.
Fixes FS#502.
(cherry picked from commit 96ed69101da254b0cb61a0dfc42bd48d27bfacb9
and squashed with commit f2fdd68664)
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This fixes the LED configuration for the D-Link DIR-869 A1. In order to
support the device I probed around using an initramfs image for the
UniFi AC. Pulling GPIO 15 to low enabled the LEDs while high disabled them.
GPIO 16 set to low meant that the color was white while pulling it to high
made the color change to orange. The past code was written based upon these
findings.
However, running a flashed image I now discovered that GPIO 15 controls the
orange LEDs while GPIO 16 controls the white ones and that both are active
when low. This means that the GPIOs were inverted and one active_low was set
wrong which this patch fixes.
Behavior of the LED front after this patch is applied:
cat /sys/devices/platform/leds-gpio/leds/d-link:white:status/brightness
0 -> white LEDs are OFF
255 -> white LEDs are ON
cat /sys/devices/platform/leds-gpio/leds/d-link🍊status/brightness
0 -> orange LEDs are OFF
255 -> orange LEDs are ON
If the brightness of both is set to 255 the LED front will be white.
If the brightness of both is set to 0 the LED front will be off.
Signed-off-by: Florian Beier <beier.florian@gmail.com>
The ZyXEL NBG6817 calculates all MAC addresses based on the ethaddr
value stored in the U-Boot environment (0:APPSBLENV). No MAC addresses
are stored in the ART partition and the generated MAC addresses for the
wlan interfaces alternate randomly between 12:34:56:78:90:12 and
00:03:7f:12:34:56.
interface new/ OEM MAC old MAC
wlan-2.4g (phy1): ethaddr undefined
wlan-5g (phy0): ethaddr + 1 undefined
lan : ethaddr + 2 ethaddr
wan : ethaddr + 3 ethaddr + 1
This patch defines stable MAC addresses for the wlan interfaces for
the first time instead of generating them at random. The previously
defined values for lan/ wan are changed to follow the settings of the
OEM firmware.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
The ZyXEL NBG6817 uses an eMMC flash for the rootfs, which is split
into the readonly squashfs and ext4 for the overlay. This adds the
required package to the device packages to allow mounting the overlay
by default.
/dev/root on /rom type squashfs (ro,relatime)
proc on /proc type proc (rw,nosuid,nodev,noexec,noatime)
sysfs on /sys type sysfs (rw,nosuid,nodev,noexec,noatime)
tmpfs on /tmp type tmpfs (rw,nosuid,nodev,noatime)
/dev/loop0 on /overlay type ext4 (rw,noatime,data=ordered)
overlayfs:/overlay on / type overlay (rw,noatime,lowerdir=/,upperdir=/overlay/upper,workdir=/overlay/work)
tmpfs on /dev type tmpfs (rw,nosuid,relatime,size=512k,mode=755)
devpts on /dev/pts type devpts (rw,nosuid,noexec,relatime,mode=600,ptmxmode=000)
debugfs on /sys/kernel/debug type debugfs (rw,noatime)
mountd(pid1040) on /tmp/run/blockd type autofs (rw,relatime,fd=7,pgrp=1,timeout=30,minproto=5,maxproto=5,indirect)
Before this commit, the ext4 based overlayfs could not be mounted,
which left only the tmpfs based/ volatile emergency overlay in place.
Fixes: https://forum.lede-project.org/t/zyxel-nbg6817-flashing-from-oem/768
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Remove the ephy-pins from the ethernet device tree node. The ephy-pins
are useed to controll the ePHY LEDs and this board doesn't have these.
Instead one of the ePHY pins is used in GPIO mode to control the WAN
LED.
Use the switch LED trigger to control the WAN LED. Move the power LED
handling to diag.sh to show the boot status via this LED.
Add the missing kernel packages for USB and microSD card reader to the
default package selection.
Fix the maximum image size value. The board has a 32MByte flash chip.
Fixes: FS#1055
Signed-off-by: Edmunt Pienkowsky <roed@onet.eu>
[make the commit message more verbose, remove GPIO pinmux for pins not
used as GPIOs]
Signed-off-by: Mathias Kresin <dev@kresin.me>
With removing the boards from the the default case to fix the xDSL WAN
MAC-Address, the setting for the default LAN interface wasn't added.
Fixes: 92a12c434c ("lantiq: fix avm fritz box mac addresses")
Signed-off-by: Mathias Kresin <dev@kresin.me>
Zyxel NBG6817 features a WiFi button, which becomes functional by setting
correct GPIO. It is a switch-type button, so it emits KEY_RFKILL on each ON
and OFF state. This is achieved by setting input-type to EV_SW.
Signed-off-by: Tolga Cakir <tolga@cevel.net>
the nexx wt3020-8M has a usb 2.0 port,
add usb 2.0 support packages to its default package list.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
The ARV752DPW22 has the same generic mac address in the EEPROM as it
was already noticed for other lantiq boards using a ralink wireless.
Use the base mac address from the boardconfig partition as it is done
by the stock firmware.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Refresh patches.
Compile-tested for ar71xx - Archer C7 v2
Runtime-tested on ar71xx - Archer C7 v2
Fixes CVE-2017-15265.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
[remove 2nd CVE as it was fixed in mac80211 in commit bff16304b0]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
The subtarget cleanups made in cabf775 "x86: Refresh subtargets kernel config"
removed some important symbol disable statements, so revert the changes to the
subtarget configs for now.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Xen support for x86/generic was added in 296772f9. This commit also
enables it for x86/64.
This was successfully tested with Xen 4.5.
Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
This was done by simply running `make kernel_menuconfig CONFIG_TARGET=subtarget`
and then saving without changing any option.
Having consistent kernel config is important to avoid surprises, such
as the issue fixed with 6f0367c9 (where Xen support was silently
disabled when building the kernel, although it was present in the
initial config)
As far as I understand the build system, this shouldn't have any
user-visible impact, because the build system already merges the
various kernel configs during build.
Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
The Xen serial console has been broken since the xen_domu subtarget
was merged in the generic x86 subtarget (commits 296772f9 and b36e24f3).
The reason for the broken serial console seems to be an IRQ conflict
between the serial console driver and the PATA_LEGACY driver:
[ 1.330125] genirq: Flags mismatch irq 8. 00000000 (hvc_console) vs. 00000000 (platform[pata_legacy.4])
[ 1.330134] hvc_open: request_irq failed with rc -16.
[ 1.330148] Warning: unable to open an initial console.
Just drop the PATA_LEGACY driver from the x86/generic and x86_64
subtargets, since this driver is marked experimental and only supports
very old ISA devices anyway. It is still included in the x86/legacy
subtarget where it rightfully belongs.
Fixes: FS#787
Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
This is a backport of 641a65fd06 in master.
This change re-enables PAE for the 32-bit x86 subtarget, which is
interesting in its own right but also necessary for Xen support.
Commit af1d1ebd ("x86: enable 4G high memory support for generic (32bit)
subtarget") inadvertently disabled both PAE and Xen support.
Fixes: FS#908
Cc: Daniel Golle <daniel@makrotopia.org>
Cc: Jo-Philipp Wich <jo@mein.io>
Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
This PHY requires some extra programming to work reliably with all
devices. Backport upstream fix for it.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Backport required DT changes from commit dabdd123c9.
Significantly improves stability and performance for MT76x2 and MT7603
Signed-off-by: Felix Fietkau <nbd@nbd.name>
A default rssileds config exists for the TP-Link WA850RE v1 but the
rssiled package is not included by default.
The compressed 17.01.3 image size increases by 3302 bytes which should
be tolerable even for a 4MB flash board.
Fixes: FS#1043
Signed-off-by: Mathias Kresin <dev@kresin.me>
The current makefile unnecessarily pads sysupgrade image for Archer devices.
This has three implications:
1. higher risk of OOM when uploading the binary image to the device
2. much slower upgrade due to time wasted erasing and writing padding
3. grows image beyond available flash size if metadata are appended
This is already fixed in master, albeit in a completely different way (the
whole target have been reworked)
Fixes: FS#1025, FS#1039
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
Module definitions for kmod-wdt-sunxi and kmod-eeprom-sunxi are removed
(wdt-sunxi was builtin anyways; nvmem-sunxi, which is the new name of
eeprom-sunxi is changed to builtin). As kmod-eeprom-sunxi was specified
in DEFAULT_PACKAGES, but not available on kernel 4.4, it was breaking the
image builder.
Support for kmod-sunxi-ir is added for kernel 4.4 (it is unclear why it
was disable before, it builds fine with with kernel 4.4).
Condtionals only relevant for pre-4.4 kernels are removed from modules.mk,
as sunxi does't support older kernels anymore.
Fixes FS#755.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
4.4.80+ contains 71a165f6397df07a06ce643de5c2dbae29bd3cfb, 4.9.41+ contains
6c78197e4a69c19e61dfe904fdc661b2aee8ec20 which are all backports of upstream
commit 0878fff1f42c18e448ab5b8b4f6a3eb32365b5b6 ("net: phy: Do not perform
software reset for Generic PHY").
Our local patch is no longer needed, all this patch was doing was utilizing
gen10g_soft_reset which does nothing either, so just keep the code unchanged.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
USB doesn't work in some danube boards because otg_cap
is missing since previous changes made on the USB-dwc2
lantiq driver. Fix it.
Tested on the ARV7518PW router.
Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
The order of LAN ports shown in Luci is reversed compared to what is
written on the case of the device. Fix the order so that they match.
Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
The addresses were read from the 'config' partition, which would not always
contain the addresses at the same offsets, depending on the stock firmware
version used before flashing LEDE. Change this to get the addresses from
the 'product-info' partition, which is read-only.
Reported-and-tested-by: Andreas Ziegler <ml@andreas-ziegler.de>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
This backports fixes for setting of_node and making it possible to read
extra info from DT. This was partially fixed by:
[PATCH] leds: leds-gpio: Set of_node for created LED devices
but it didn't work during initialization.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Refresh patches.
Minor update 704-phy-no-genphy-soft-reset.patch which was partially
accepted upstream.
Compile-tested on ar71xx.
Runtime-tested on ar71xx.
Fixes the following vulnerabilities:
- CVE-2017-7533 (4.4.80)
- CVE-2017-1000111 (4.4.82)
- CVE-2017-1000112 (4.4.82)
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
By adding the ICPlus IP1001 phy driver an already set RGMII delay mode
is reset during driver load.
Set the rgmii rx delay to fix corrupt/no packages in case the WAN port
negotiates to 1000MBit.
Fixes: FS#670
Signed-off-by: Mathias Kresin <dev@kresin.me>
By default the wlan eprom contains the generic ralink MAC which is not
the vendor (TP-Link) one. Based on OFW bootlog, it appears that addresses
are decremented from the ethernet MAC.
This patch fixes the MAC address for wlan2g in line with OFW.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
Reference the Omnima MiniEMBWiFi device tree source file in the image
build code. Otherwise the dts of the image processed before is used.
Signed-off-by: Mathias Kresin <dev@kresin.me>
there were 2 bugs
*) core1 came up with a bad bogo mips, looks like the clock needed time to stabilize
*) HPT frequency was not set making r4k timers not come up properly
Backport of 9551d91b1d "ralink: fix rcu_sched stalls on mt7621".
Signed-off-by: John Crispin <john@phrozen.org>