The first version of this script allowed just 4Mb factory images.
With this patch is possible to set the maximum size of the payload.
For an 8Mb flash, the corresponding maxsize is:
8 * 1024 * 1024 - 5 * 64 * 1024 = 8388608 - 327680 = 8060928
If the -m argument is not set, the default maximum size will be
used for backward compatibility.
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
This patch fixes the active_low setting and
converts all of the physical keys on the wndr4700
to utilize the interrupt-driven gpio-keys driver
over the polled version.
The sdcard-insertion hack has been removed since the
block-subsystem will now be polling the device instead.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Upstream Linux's input gpio-keys driver supports
specifying a external interrupt for a gpio via the
'interrupts' properties as well as having support
for software debounce.
This patch ports these features to OpenWrt's event
version. Only the "pure" interrupt-driven support is
left behind, since this goes a bit against the "gpio"
in the "gpio-keys" and I don't have a real device to
test this with.
This patch also silences the generated warnings showing
up since 4.14 due to the 'constification' of the
struct gpio_keys_button *buttons variable in the
upstream struct gpio_keys_platform_data declaration.
gpio-button-hotplug.c: In function 'gpio_keys_get_devtree_pdata':
gpio-button-hotplug.c:392:10: warning: assignment discards 'const'
qualifier from pointer target type [-Wdiscarded-qualifiers]
button = &pdata->buttons[i++];
^
gpio-button-hotplug.c: In function 'gpio_keys_button_probe':
gpio-button-hotplug.c:537:12: warning: assignment discards 'const'
qualifier from pointer target type [-Wdiscarded-qualifiers]
bdata->b = &pdata->buttons[i];
^
gpio-button-hotplug.c: In function 'gpio_keys_probe':
gpio-button-hotplug.c:563:37: warning: initialization discards 'const'
qualifier from pointer target type [-Wdiscarded-qualifiers]
struct gpio_keys_button *button = &pdata->buttons[i];
^
Acked-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Upstream PPP project has added in commit 8e77984 options to tune discovery
timeout and attempts in the rp-pppoe plugin.
Expose these options in the uci datamodel for pppoe:
padi_attempts: Number of discovery attempts
padi_timeout: Initial timeout for discovery packets in seconds
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
It is not always necessary to add a host route for the gre peer address.
This introduces a new config option 'nohostroute' (similar to the
option introduced for wireguard in d8e2e19) to allow to disable
the creation of those routes explicitely.
Signed-off-by: Fabian Bläse <fabian@blaese.de>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase]
This version bump contains the following commit to fix FS#2222
3b3e368 uclient-http: set data_eof when content-length is 0
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
This adds support for kernel 4.14 to the target and directly make it the
default kernel version to use.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Sandeep Sheriker <sandeepsheriker.mallikarjun@microchip.com>
Instead of maintaining 3 very similar subtargets merge them into one.
This does not use the Arm NEON extension any more, because the SAMA5D3
does not support NEON.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Sandeep Sheriker <sandeepsheriker.mallikarjun@microchip.com>
This removes some settings which are normally set by the generic
configuration and should not be changed.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Sandeep Sheriker <sandeepsheriker.mallikarjun@microchip.com>
The configuration of the sama5d4 subtarget was used as the default
configuration and then the subtarget configurations were adapted.
The resulting kernel configuration without any extra modules selected is
still the same.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Sandeep Sheriker <sandeepsheriker.mallikarjun@microchip.com>
The restart button is currently assigned to KEY_POWER power script but
an easily accessible button immediately powering off the device is
undesirable. Switch to using new KEY_POWER2 reboot script with 5 second
seen delay.
Fixes: FS#1965
Signed-off-by: Alan Swanson <reiver@improbability.net>
Signed-off-by: Petr Štetiar <ynezz@true.cz> [long line wrap]
For devices such as BTHOMEHUBV5A with both reset and restart buttons,
its easily accessible restart button has been assigned to KEY_POWER
power script to poweroff preventing accidental (or malicious) factory
resets by KEY_RESTART reset script. However an easily accessible button
immediately powering off the device is also undesirable.
As KEY_RESTART is already used for reset script (and there's no
KEY_REBOOT in Linux input events), use KEY_POWER2 for rebooting via new
reboot script with 5 second seen delay.
Fixes: FS#1965
Signed-off-by: Alan Swanson <reiver@improbability.net>
Signed-off-by: Petr Štetiar <ynezz@true.cz> [long line wrap]
For devices such as BTHOMEHUBV5A with both reset and restart buttons,
its easily accessible restart button has been assigned to KEY_POWER
power script to poweroff preventing accidental (or malicious) factory
resets by KEY_RESTART reset script. However an easily accessible button
immediately powering off the device is also undesirable.
As KEY_RESTART is already used for reset script (and there's no
KEY_REBOOT in Linux input events), use KEY_POWER2 for rebooting via new
reboot script with 5 second seen delay.
Fixes: FS#1965
Signed-off-by: Alan Swanson <reiver@improbability.net>
Signed-off-by: Petr Štetiar <ynezz@true.cz> [long line wrap]
For devices such as BTHOMEHUBV5A with both reset and restart buttons,
its easily accessible restart button has been assigned to KEY_POWER
power script to poweroff preventing accidental (or malicious) factory
resets by KEY_RESTART reset script. However an easily accessible button
immediately powering off the device is also undesirable.
Fixes: FS#1965
Signed-off-by: Alan Swanson <reiver@improbability.net>
Signed-off-by: Petr Štetiar <ynezz@true.cz> [long line wrap]
ade00ca585a4 container: fix .dockerenv stat check
385b904b2f0a hotplug: improve error message during group ownership change
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Add upstream patch from:
https://git.busybox.net/busybox/commit/?id=028c5aa18b5273c029f0278232d922ee1a164de6
The patch fixes a problem with an infinite loop causing 100% CPU usage
when running the following command /lib/preinit/10_indicate_preinit
without the CAP_NET_ADMIN capability (such as in Docker):
ip -4 address flush dev $pi_ifname
Signed-off-by: Mikael Magnusson <mikma@users.sourceforge.net>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [refresh patch]
This patch fixes following missing bits:
- add missing 'compatible' property on firmware partition
- set vendor partition 'userconfig' read-only
Fixes: 30dcbc741d ("ath79: add support for EnGenius ECB1750")
Signed-off-by: Sven Friedmann <sf.openwrt@okay.ms>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
SoC: AR9344
RAM: 128MB
Flash: 16MiB Winbond 25Q128BVFG SPI NOR
5GHz WiFi: AR9380 PCIe 3x3:3 802.11n
2.4GHz WiFi: AR9344 (SoC) AHB 2x2:2 802.11n
5x Gigabit ethernet via AR8327N switch (green + amber LEDs)
2x USB 2.0 via GL850G hub
4x front LEDs from SoC GPIO
1x front WPS button from SoC GPIO
1x bottom reset button from SoC GPIO
Known issues:
AR8327N LEDs only have default functionality, not presented in sysfs.
This is a regression from ar71xx.
UART header JP1, 115200 no parity 1 stop
TX
GND
VCC
(N/P)
RX
See https://openwrt.org/toh/wd/n750 for flashing detail.
Procedures unchanged from ar71xx.
Tested sysupgrade + factory flash from WD Emergency Recovery
Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
Don't set the default firewall zone to wan if not specified to keep the
behavior aligned with other tunnel protocols like gre and 6rd.
If the interface zone is not specified try to get it from the firewall config
when constructing the procd firewall rule.
While at it only add procd inbound/outbound firewall rules if a zone is specified.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Don't set the default firewall zone to wan if not specified to keep the
behavior aligned with other tunnel protocols like gre and 6rd.
If the interface zone is not specified try to get it from the firewall config
when constructing the procd firewall rule.
While at it only add a procd inbound firewall rule if a zone is specified.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* Feature: Add support for 200Gbps (50Gbps per lane) link mode
* Feature: simplify handling of PHY tunable downshift
* Feature: add support for PHY tunable Fast Link Down
* Feature: add PHY Fast Link Down tunable to man page
* Feature: Add a 'start N' option when specifying the Rx flow hash indirection table.
* Feature: Add bash-completion script
* Feature: add 10000baseR_FEC link mode name
* Fix: qsfp: fix special value comparison
* Feature: move option parsing related code into function
* Feature: move cmdline_coalesce out of do_scoalesce
* Feature: introduce new ioctl for per-queue settings
* Feature: support per-queue sub command --show-coalesce
* Feature: support per-queue sub command --coalesce
* Fix: fix up dump_coalesce output to match actual option names
* Feature: fec: add pretty dump
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This makes sysupgrade work on the D-Link DIR-685 after
initial factory install.
We create the platform.sh script to support sysupgrade
on more targets as we move on with sysupgrade support.
Cc: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
[cleanup in platform.sh, removed superfluous SUPPORTED_DEVICES]
Lua's LNUM patch currently doesn't parse properly certain numbers as
it's visible from the following simple tests.
On x86_64 host (stock Lua 5.1.5, expected output):
$ /usr/bin/lua -e 'print(0x80000000); print(0x80000000000); print(0x100000000)'
2147483648
8796093022208
4294967296
On x86_64 host:
$ staging_dir/hostpkg/bin/lua -e 'print(0x80000000); print(0x80000000000); print(0x100000000)'
-2147483648
0
0
On x86_64 target:
$ lua -e 'print(0x80000000); print(0x80000000000); print(0x100000000)'
-2147483648
0
0
On ath79 target:
$ lua -e 'print(0x80000000); print(0x80000000000); print(0x100000000)'
-2147483648
8796093022208
4294967296
It's caused by two issues fixed in this patch, first issue is caused by
unhadled strtoul overflow and second one is caused by the cast of
unsigned to signed Lua integer when parsing from hex literal.
Run tested on:
* Zidoo Z9S with RTD1296 CPU (aarch64_cortex-a53)
* qemu/x86_64
* qemu/armvirt_64
* ath79
Signed-off-by: Liangbin Lian <jjm2473@gmail.com>
[commit subject/message touches, fixed From to match SOB, fixed another
unhandled case in luaO_str2i, host Lua, package bump]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This reverts commit 0111b86f1d as it
breaks on Linux distributions without ed support
./fix-libmath_h: line 1: ed: command not found
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
When running OpenWrt inside an LXC container no shell is opend as LXC
defaults to a virtual /dev/console.
This patch allows to enter a shell after starting the container via
`lxc-start`, without it is only posible to access a shell on tty1 via
`lxc-console`.
Signed-off-by: Paul Spooren <mail@aparcar.org>
The vendor firmware only uses two mac addresses, the mac address on the
label and the label + 1. While checking multiple devices, all labels have
even mac addresses. Concluding only 2 address are assigned to a device.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
The GL.iNet AR750S USB and microSD port is currently not working out of
the box. GPIO 7 is used to control the power of the USB port. Add GPIO
7 as a fixed-regulator for the port. Also add &usb1 to DTS to get the
microSD port to work.
Signed-off-by: Alexander Wördekemper <alexwoerde@web.de>
This patch fixes `sysupgrade -n` when flashed with rootfs of the same
size as currently running, so the rootfs_data wouldn't get destroyed and
thus survive reboot. So let's fix it by always cleaning up the content
of the rootfs_data during sysupgrade.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
ar71xx uses `archer-c7-v5` for led prefix, but ath79 sticks to more
generic `tplink` as the DTS is reused by more boards, so we need to
perform migrations of the LED names during upgrade.
Cc: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
