Some boards have external switches different than mt7530.
This patch allow to use mdio-mode without 0x1f register.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
A buffer is split into multiple descriptors if it exceeds 16 KB.
Apply the same split for the skb head as well (to deal with corner cases
on fraglist support)
Signed-off-by: Felix Fietkau <nbd@nbd.name>
To share mdio addr for IntPHY and ExtPHY,
as described in the documentation (MT7620_ProgrammingGuide.pdf).
(refer: http://download.villagetelco.org/hardware/MT7620/MT7620_ProgrammingGuide.pdf)
when port4 setup to work as gmac mode, dts like:
&gsw {
mediatek,port4 = "gmac";
};
we should set SYSCFG1.GE2_MODE==0x0 (RGMII).
but SYSCFG1.GE2_MODE may have been set to 3(RJ-45) by uboot/default
so we need to re-set it to 0x0
before this changes:
gsw: 4FE + 2GE may not work correctly and MDIO addr 4 cannot be used by ExtPHY
after this changes:
gsw: 4FE + 2GE works and MDIO addr 4 can be used by ExtPHY
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
When PHY's are defined on the MDIO bus in the DTS, gigabit support was
being masked out for no apparent reason, pegging all such ports to 10/100.
If gigabit support must be disabled for some reason, there should be a
"max-speed" property in the DTS.
Reported-by: James McKenzie <openwrt@madingley.org>
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
Mediatek has a reference platform that pairs an MT7620A with an MT7530W,
where the latter responds on MDIO address 0x1f while both chips respond on
0x0 to 0x4. The driver special-cases this arrangement to make sure it's
talking to the right chip, but two different ways in two different places.
This patch consolidates the detection without the current requirement of
both tests to be separately satisfied in the DTS.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
The code has some remaining issues that cause ethernet hangs, so
disable it for now until we can get it fixed
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Using the NAPI or netdev frag cache along with other drivers can lead to
32 KiB pages being held for a long time, despite only being used for
very few page fragment.
This can happen if the ethernet driver grabs one or two fragments for rx
ring refill, while other drivers use (and free up) the remaining
fragments. The 32 KiB higher-order page can only be freed once all users
have freed their fragments, which only happens after the rings of all
drivers holding the fragments have wrapped around.
Depending on the traffic patterns, this can waste a lot of memory and
look a lot like a memory leak
Signed-off-by: Felix Fietkau <nbd@nbd.name>
GRO stores packets as fraglist. If they are routed back to the ethernet
device, they need to be re-segmented if the driver does not support
sending fraglists.
Add the missing support for that, along with a missing feature flag that
allows full routed GRO->TSO offload.
Considerably reduces CPU utilization for routing
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Since kernel 4.10 commit 61e84623ace3 ("net: centralize net_device
min/max MTU checking"), the range of mtu is [min_mtu, max_mtu], which
is [68, 1500] by default.
It's necessary to set a max_mtu if a mtu > 1500 is supported.
Signed-off-by: Mathias Kresin <dev@kresin.me>
In case of error, the function devm_ioremap_resource() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should
be replaced with IS_ERR().
Fixes: f079b6406348 ("staging: mt7621-eth: add gigabit switch driver (GSW)")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of error, the function of_phy_connect() returns NULL pointer not
ERR_PTR(). The IS_ERR() test in the return value check should be
replaced with NULL test.
Fixes: e3cbf478f846 ("staging: mt7621-eth: add the drivers core files")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of error, the function devm_ioremap_resource() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should
be replaced with IS_ERR().
Fixes: e3cbf478f846 ("staging: mt7621-eth: add the drivers core files")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The stats update needs to protect against being interrupted by a tasklet
The u64 stats seqlock needs to be initialized
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Supports IPv4 flow offloading on MT7621 for Routing, SNAT and DNAT
Supported are regular ethernet->ethernet connections, including one
802.1q VLAN and/or PPPoE encapsulation
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In some boards port 4 of mt7620 switch is powered down in bootloader
configuration as lan/wan package leak mitigation.
Reset ephy port 4 to default settings to power up the port.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
[clarify issue in commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
The hardware emits some interrupts while initializing and handling them
can mess up the state or cause infinite loops.
Fix this by disabling IRQs during init and re-enabling them afterwards
Signed-off-by: Felix Fietkau <nbd@nbd.name>
- removed upstreamed patches
- 0901-spansion_nand_id_fix.patch is disabled, not clear if it's needed
Signed-off-by: Roman Yeryomin <roman@advem.lv>
Signed-off-by: John Crispin <john@phrozen.org>
