Broadcom's U-Boot contains environment data blocks. They need to be
found (offsets aren't predefined) to access env variables.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
When the v1 and v2 variants of the U6LR were introduced, the board
network config was not adapted to the new device names. Due to this, the
wrong network config is applied during initial boot. The resulting
config has lan, wan and a switch, while this device only has a single
ethernet interface without a switch.
Fix this by using a wildcard that matches all the variants.
Fixes: 15a02471bb ("mediatek: new target mt7622-ubnt-unifi-6-lr-v1")
Fixes: 5c8d3893a7 ("mediatek: new target ubnt_unifi-6-lr-v1-ubootmod")
Fixes: 31d86a1a11 ("mediatek: add Ubiquiti UniFi 6 LR v2 targets")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Daniel Golle <daniel@makrotopia.org>
Instead of waiting for complete workflow finish, then downloading the
artifacts, unpacking them and inspecting them, lets try to make the
build failure immediately visible in the log output:
====== Make errors from logs/target/linux/compile.txt ======
* Legacy (non-UHI/non-FIT) Boards
*
Support MIPS SEAD-3 boards (LEGACY_BOARD_SEAD3) [N/y/?] (NEW)
Error in reading or end of file.
make[6]: *** [scripts/kconfig/Makefile:77: syncconfig] Error 1
make[5]: *** [Makefile:616: syncconfig] Error 2
make[4]: *** [Makefile:736: include/config/auto.conf.cmd] Error 2
make[3]: *** [Makefile:24: build_dir/target-mipsel-openwrt-linux-musl_musl/linux-ramips_mt7620/linux-5.15.62/.modules] Error 2
make[2]: *** [Makefile:11: compile] Error 2
time: target/linux/compile#30.09#11.30#37.92
Signed-off-by: Petr Štetiar <ynezz@true.cz>
b704dc72e tests: sigma_dut and updated ConfResult value for Configurator failures
89de431f2 DPP: Add config response status value to DPP-CONF-SENT
10104915a tests: sigma_dut and DPP PB session overlap
80d5e264c Enhance QCA vendor roam event to indicate MLO links after reassociation
662249306 Update copyright notices for the QCA vendor definitions
8adcdd659 tests: Temporary workaround for dpp_chirp_ap_5g
ddcd15c2d tests: Fix fuzzing/sae build
7fa67861a tests: Fix p2p_channel_avoid3
ee3567d65 tests: Add more time for scan/connection
1d08b238c nl80211: Allow more time for the initial scan with 6 GHz
ac9e6a2ab tests: Allow 6 GHz opclasses in MBO checks
faf9c04cb Remove a host of unnecessary OPENSSL_IS_BORINGSSL ifdefs
b9cd5a82f Always process pending QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_ROAM_AUTH data
ef4cd8e33 QoS: Use common classifier_mask for ipv4/ipv6
93be02592 Add fixed FDD mode to qca_btc_chain_mode QCA vendor attribute
e7cbfa1c1 tests: sigma_dut and DPP Enrollee unsupported curves
5565fbee2 DPP: Check Enrollee supported curves when building Config Response
ceae05cec tests: sigma_dut and DPP MUDURL setting for hostapd
4cfb484e9 DPP: Allow dpp_controller_start without arguments in CLIs
c97000933 Fix ifdef condition for imsi_privacy_cert
2a9a61d6c tests: SAE with extended key AKM
e35f6ed1d tests: More detailed report on SAE PMKSA caching error case
f70db167a SAE: Derive a variable length PMK with the new AKM suites
91010e6f6 SAE: Indicate AKM suite selector in commit for new AKM suites
e81ec0962 SAE: Use H2E unconditionally with the new AKM suites
f8eed2e8b SAE: Store PMK length and AKM in SAE data
9dc4e9d13 SAE: EAPOL-Key and key/MIC length information for the new AKM suites
a32ef3cfb SAE: Driver capability flags for the new SAE AKM suites
91df8c9c6 SAE: Internal WPA_KEY_MGMT_* defines for extended key AKMs
5c8a714b1 SAE: Use wpa_key_mgmt_sae() helper
5456b0f26 Define new RSN AKM suite selector values
def33101c DPP: Clear push button announcement state on wpa_supplicant FLUSH
35587fa8f tests: DPP Controller/Relay with need to discover Controller
d22dfe918 DPP: Event message for indicating when Relay would need a Controller
ca7892e98 tests: DPP Relay and adding/removing connection to a Controller
bfe3cfc38 DPP: Allow Relay connections to Controllers to be added and removed
808834b18 Add a comparison function for hostapd_ip_addr
f7763880b DPP: Advertise Configurator connectivity on Relay automatically
ff7cc1d49 tests: DPP Relay and dynamic Controller addition
ca682f80a DPP: Dynamic Controller initiated connection on Relay
d2388bcca DPP: Strict validation of PKEX peer bootstrapping key during auth
a7b8cef8b DPP3: Fix push button boostrapping key passing through PKEX
69d7c8e6b DPP: Add peer=id entry for PKEX-over-TCP case
b607d2723 tests: sigma_dut and DPP PB Configurator in wpa_supplicant
1ff9251a8 DPP3: Push button Configurator in wpa_supplicant
b94e46bc7 tests: PB Configurator in wpa_supplicant
ca4e82cbf tests: sigma_dut DPP/PKEX initiator as Configurator over TCP and Wi-Fi
e9137950f DPP: Recognize own PKEX Exchange Request if it ends up being received
692956446 DPP: Note PKEX code/identifier deletion in debug log
dfa9183b1 tests: DPP reconfig after Controller-initiated operation through Relay
ae4a3a6f6 DPP: Add DPP-CONF-REQ-RX event for Controller
17216b524 tests: sigma_dut DPP/PKEX initiator as Configurator (TCP) through Relay
fb2937b85 DPP: Allow Controller to initiate PKEX through Relay
15af83cf1 DPP: Delete PKEX code and identifier on success completion of PKEX
d86ed5b72 tests: Allow DPP_PKEX_REMOVE success in dpp_pkex_hostapd_errors
0a4f391b1 tests: sigma_dut and DPP Connector Privacy
479e412a6 DPP3: Default value for dpp_connector_privacy
7d12871ba test: DPP Private Peer Introduction protocol
148de3e0d DPP3: Private Peer Introduction protocol
786ea402b HPKE base mode with single-shot API
f0273bc81 OpenSSL: Remove a forgotten debug print
f2bb0839f test: DPP 3rd party config information
68209ddbe DPP: Allow 3rd party information to be added into config object
0e2217c95 DPP: Allow 3rd party information to be added into config request obj
3d82fbe05 Add QCA vendor subcommand and attributes for SCS rule configuration
16b62ddfa QCA vendor attribute for DBAM configuration
004b1ff47 tests: DPP Controller initiating through Relay
451ede2c3 DPP: Allow AP/Relay to be configured to listed for new TCP connections
248654d36 tests: sigma_dut DPP PB test cases
697b7d7ec tests: DPP push button
7bbe85987 DPP3: Allow external configuration to be specified on AP for PB
8db786a43 DPP3: Testing functionality for push button announcements
37bccfcab DPP3: Push button bootstrap mechanism
a0054fe7c Add AP and STA specific P802.11az security capabilities (vendor command)
159e63613 QCA vendor command for CoAP offload processing
3b7bb17f6 Add QCA vendor attribute for TIM beacon statistics
09a281e52 Add QCA vendor interface for PASN offload to userspace
809fb96fa Add a vendor attribute to configure concurrency policy for AP interface
a5754f531 Rename QCA_NL80211_VENDOR_SUBCMD_CONCURRENT_MULTI_STA_POLICY
085a3fc76 EHT: Add 320 channel width support
bafe35df0 Move CHANWIDTH_* definitions from ieee80211_defs.h to defs.h
92f549901 tests: Remove the 80+80 vs. 160 part from wpa2_ocv_ap_vht160_mismatch
c580c2aec tests: Make OCV negative test error cases more robust
3c2ba98ad Add QCA vendor event to indicate driver recovery after internal failures
6b461f68c Set current_ssid before changing state to ASSOCIATING
8dd826741 QCA vendor attribute to configure direct data path for audio traffic
504be2f9d QCA vendor command support to get WLAN radio combinations
d5905dbc8 OCV: Check the Frequency Segment 1 Channel Number only on 80+80 MHz
Signed-off-by: David Bauer <mail@david-bauer.net>
Use a make variable pattern for the url
so that only one version number needs to be changed
when version is bumped.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
With the commit 5876d6a62f the command under
`/usr/sbin/grub-bios-setup` has been moved to its own package named
`grub-bios-setup`.
The script `81_upgrade_bootloader` under `/lib/preinit` is used by all
x86 targets to update the bootloader. The script is using the command
`grub-bios-setup` for this.
I get the following output at the first boot after the upgrade.
`/etc/preinit: line 9: /usr/sbin/grub-bios-setup: not found`.
To fix this, the DEFAULT_PACKAGES dependency is extended by the entry
`grub2-bios-setup` so that the missing command is installed again.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Backport upstream code split patch for qca8k needed for ipq40xx target
to correctly implement a DSA driver.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Grant pull-requests write permission to the labeler workflow and
read-only to everything else.
Signed-off-by: Alex Low <aleksandrosansan@gmail.com>
[ wrap to 80 columns and fix wrong author as requested by author itself ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Currently we fix interrupts/timers for the secondary CPU by patching
vsmp_init_secondary(). Get a little bit more generic and use the
upstream recommended way instead. Additionally avoid a check around
register_cps_smp_ops() because it does that itself.
See https://lkml.org/lkml/2022/9/12/522
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
The interrupt controller depends on two control registers. GIMR enables
or disables interrupts and IRRx routes these to MIPS CPU interrupts 2-7.
Wiki currently states "A value of '0' (in IRRx) disconnects this input from
the output line, independent of the line's setting in GIMR."
Contrary to normal intuition this statement DOES NOT mean, that interrupts
can be disabled by IRRx alone. The sad truth was discovered by enabling
SMP for an Zyxel XGS1010 on the 930x target. It shows that driver and
interrupts behave as follows:
- Timer 0 interrupt 7 has active routing to CPU0 and no routing to CPU1
- Timer 1 interrupt 8 has no routing to CPU0 and active routing to CPU1
- Unmasking (enabling) interrupts writes 1 bits to all GIMR registers
- Masking (disabling) interrupts writes 0 bits to both GIMR registers
During operation we can encounter a situation like
- GIMR bit for a interrupt/CPU combination is set to enabed (=1)
- IRRx routing bits for a interrupt/CPU combination are set to disabed (=0)
This setting already allows the hardware to fire interrupts to the target
CPU/VPE if the other CPU/VPE is currently busy. Especially for CPU bound
timer interrupts this is lethal. If timer interrupt 7 arrives at CPU1 and
vice versa for interrupt 8 the restart trigger gets lost. The timer dies
and a msleep() operation in the kernel will halt endlessly.
Fix this by tracking the IRRx active routing setting in a new bitfield with
0="routing active" and 1="no routing". Enable interrupts in GIMR only
for a interrupt & CPU if routing is active. Thus we have
- GIMR = 0 / IRRx = 0 -> everything disabled
- GIMR = 1 / IRRx > 0 -> active and normal routing
- GIMR = 0 / IRRx > 0 -> masked (disabled) with normal routing
- GIMR = 1 / IRRx = 0 -> no longer possible
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
The image builds for Linksys EA6350 v3, EA8300, and MR8300 currently
fail on buildbots due to the KERNEL_SIZE, as stated in commit
17b7756b5a ("ipq40xx: 5.15: add testing kernel version"). Disable
these boards for now.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Change phy-mode of gmac1 to rgmii on mt7621.dtsi. Same code path is
followed for delayed rgmii and rgmii phy-mode on mtk_eth_soc.c.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Add the missing LEDs for GB-PC2. Some of these LEDs don't exist on the
device schematics. Tests on a GB-PC2 by me and Petr proved otherwise.
Remove ethblack-green and ethblue-green LEDs for GB-PC1. They are not wired
to GPIO 3 or 4 and the wiring is currently unknown.
Set ethyellow-orange to display link state and activity of the ethyellow
interface for GB-PC2.
Link: https://github.com/ngiger/GnuBee_Docs/blob/master/GB-PCx/Documents/GB-PC2_V1.1_schematic.pdf
Tested-by: Petr Louda <petr.louda@outlook.cz>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
The Build prefix is used for image build commands, while the Device
prefix should be used for base recipes for devices. Apply the same
naming convention here.
While touching the file, also fix the mixed indentation.
Suggested-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Don't select channels designated for exclusive-indoor use when the
country3 element is set on outdoor operation.
Signed-off-by: David Bauer <mail@david-bauer.net>
There seems to be no reason to have the Netgear switches as part of
the main Makefile. Move it to its subtarget-specific Makefile since
it is only applicable there.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
[update commit message]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Currently supported HPE 1920 devices all have an RTL838x SoC, but there
are larger switches with RTL839x SoCs, although currently not supported.
Move the build recipe to common.mk so the larger devices can also make
use of the recipe, while moving it out of the main Makefile.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
The D-Link DGS-1210 device series currently has supported devices with
both RTL838x and RTL839x SoCs. An image build recipe has been defined in
both subtarget makefiles, but these are mostly identical, save for the
SOC variable.
Move the SOC variable from the DGS-1210 build recipes to the applicable
devices, and put the remaining duplicate code in a shared Makefile.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Hardware specification
----------------------
* RTL8393M SoC, 1 MIPS 34Kc core @ 700MHz
* 128MB DRAM
* 32MB NOR Flash
* 48 x 10/100/1000BASE-T ports
- 6 x External PHY with 8 ports (RTL8218D)
* 4 x Gigabit RJ45/SFP Combo ports
- External PHY with 4 SFP ports (RTL8214FC)
* Power LED
* Reset button on front panel
* UART (115200 8N1) via unpopulated standard 0.1" pin header marked J14
The gpio-restart node is not required but it does reset the switch.
TODO: The 4 combo ports attached to the RTL8214FC are not detect
properly. Linux kernel reports 49 and 50 as "External RTL8393 SERDES"
and 51 and 52 as "RTL8218B (external)". Those ports only work if
u-boot initialize it (for example, loading initramfs image using one
of those ports). A patch to PHY detection is needed for full support.
The firmware recovery using U-Boot is broken for all DGS-1210 tested
devices as pressing RESET does not trigger it (only if pressed from a
running stock image)
UART pinout
-----------
[o]ooo|J14
| ||`------ GND
| |`------- RX
| `-------- TX
`---------- Vcc (3V3)
Installation using OEM upgrade
------------------------------
1. Make sure you are running OEM firmware in image2 slot (logged as admin):
- > config firmware image_id 2 boot_up
- > reboot
2. Install squashfs-factory_image1.bin to image1 using (logged as admin):
- > download firmware_fromTFTP <tftpserver> factory_image1.bin
- > config firmware image_id 1 boot_up
- > reboot
Installation using serial interface
-----------------------------------
1. Press Escape key during `Hit Esc key to stop autoboot` prompt
2. Press CTRL+C keys to get into real U-Boot prompt
3. Init network with `rtk network on` command
4. Load image with `tftpboot 0x8f000000 openwrt-realtek-rtl839x-d-link_dgs-1210-52-initramfs-kernel.bin` command
5. Boot the image with `bootm` command
Once booted the initramfs, install the squashfs-sysupgrade.bin as a
normal OpenWrt system.
Dual-boot with stock firmware using writable u-boot-env
-------------------------------------------------------
From stock to OpenWrt / boot image 1 (CLI as admin):
- > config firmware image_id 1 boot_up
- > reboot
From OpenWrt to stock / boot image 2: (shell as root)
- # fw_setenv bootcmd 'run addargs ; bootm 0xb4e80000'
- # fw_setenv image '/dev/mtdblock7'
- # reboot
Debrick using serial interface
------------------------------
1. Press Escape key during `Hit Esc key to stop autoboot` prompt
2. In a Windows PC, run 'D-Link Network Assistant v2.0.2.4'. It should
detect the switch
3. Flash the firmware.
Back to stock firmware using dual-boot
--------------------------------------
If you have serial interface, you can change u-boot env vars
interrupting the boot process. If not but you are running OpenWrt, you
can dual-boot (as mentioned eariler) and skip to step 4:
1. Press Escape key during `Hit Esc key to stop autoboot` prompt
2. Press CTRL+C keys to get into real U-Boot prompt
3. Boot the image 2:
- set image /dev/mtdblock7; run addargs; bootm 0xb4e80000
4. Once booted, log as admin and change the boot image to 2
- > config firmware image_id 2 boot_up
- > reboot
5. After the boot, flash image1 with the vendor image
Back to stock firmware using DNA
--------------------------------
1. From an OpenWrt:
- # fw_setenv bootstop on
- # reboot
2. In a Windows PC, run 'D-Link Network Assistant v2.0.2.4'. It should
detect the switch
3. Flash the firmware.
It has been developed and tested on device with F3 revision.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
The D-Link DGS device tree was reorganized to better reflect the common
DT parts. The common include is named SOC specific (838X) and it seemed
like a good choice to add another common include in the future for the
RTL839X devices. From the current point of view this option is not really
needed.
1. The common part only includes data that matches RTL839X devices too.
2. The Panasonic DT structure avoids including the basic DTSI inside the
common DTSI.
Taking simplicity of the Panasonic include logic and in perparation to
provide DGS-1210-52 support it makes sense to harmonize this.
- rename common include to reflect its content
- move the link to the root DTSI directly to the device specific DTS
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Otherwise kernel 5.15 will fail to build on subtargets except for mt7621
that has enabled the config.
The disabled PINCTRL_AW9523 config disappears after a refresh, it needs
to be added back manually.
Fixes: 675cf75578 ("ramips: add config-5.15 for mt7620 subtarget")
Fixes: 001176994a ("ramips: add config-5.15 for mt76x8 subtarget")
Fixes: b9d9f33c33 ("ramips: add config-5.15 for rt288x subtarget")
Fixes: 0164dc0c25 ("ramips: add config-5.15 for rt305x subtarget")
Fixes: ef59da8669 ("ramips: add config-5.15 for rt3883 subtarget")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Currently factory.bin image recipe of ASUS RP-AC51 is not specified
explicitly and is thus set to the leaked one from the device recipe
right above, i.e. ASUS PL-AC56. Fix it to avoid potential breakage.
Fixes: 416d4483e8 ("ath79: add support for ASUS RP-AC51")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
This matches the scheme used by other target packages and will avoid
confusion with any future version.
Signed-off-by: Andre Heider <a.heider@gmail.com>
The 'fxload' tool contained in the examples provided with libusb is
actually useful and turns out to be the only way to load firmware into
some rather ancient EZ-USB microcontrollers made by Cypress (formerly
Anchor Chips).
The original 'fxload' tool from hotplug-linux has been abandonned long
ago and requires usbfs to be mounted in /proc/bus/usb/ (like it was in
Linux 2.4...).
Hence the best option is to package the modern 'fxload' from the libusb
examples which (unsurprisingly) uses libusb and works on modern
systems.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
e065a7627a46 pex: update last query sent timestamp
6c888f897862 unet-cli: add stun server list editing support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
21360a1b1ce6 cli: fix typo
abfebece0af1 wg-linux: ship a copy of linux/wireguard.h
1cbb1a543cb3 pex: reduce unnecessary ping traffic
0c2f39e52d5d pex: remove pex event debug spam
dcf1362c2104 pex: add support for sending/receiving global PEX messages via unix socket
df5f70b8858c ubus: notify on network updates
e58a56697131 add DHT discovery service
be175767bc67 pex: keep active pex hosts after the specified timeout
543e4a3d2ed7 pex: move rx header check to callback function
395659b9c415 pex: move raw ip send code to sendto_rawudp() in utils.c
dda15ea8b3b2 pex: add utility function to get the sockets based on type / address family
e88f2cd4d3f0 utils: add support for passings address family to network_get_endpoint()
639cdcdf6eda pex: add support for figuring out the external data port via STUN servers
9144339ebe1f pex: improve handling of a longer list of PEX hosts
38212218ecdd unet-cli: add DHT support
0d37ca75434d pex: automatically create host entries from incoming endpoint port notifications
035fcc56ef60 host: keep multiple endpoint candidates, one for each type
a089e8ae7504 pex: avoid sending a query to a host more than once every 15 seconds
Signed-off-by: Felix Fietkau <nbd@nbd.name>
libwolfssl-cpu-crypto is a variant of libwolfssl with support for
cryptographic CPU instructions on x86_64 and aarch64.
On aarch64, wolfSSL does not perform run-time detection, so the library
will crash when the AES functions are called. A preinst script attempts
to check for support by querying /proc/cpuinfo, if installed in a
running system. When building an image, the script will check the
DISTRIB_TARGET value in /etc/openwrt_release, and will abort
installation if target is bcm27xx.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
