Add support for SAMA5D27 SOM1 with target device as at91-sama5d27_som1_ek
in SAMA5 subtarget and build images for SAMA5D27 SOM1 Ek board.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
fetching uboot src from linux4sam/u-boot-at91 github for all at91
target.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
updating to new version v3.8.10 and copying at91bootstrap.bin to bin folder.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
Currently, the build system uses an openwrt mirror which does not currently
work and FTP can be unreliable under several circumstances. This change
implicitly allows using all the mirrors to download.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
When libressl was linked the libpthread was missing, add it in addition.
Fixes: 2c192b6916 ("tools/libressl: update to version 2.7.2")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
When libressl was linked the libpthread was missing, add it in addition.
Also make the mxsimage tool to use the OpenSSL 1.1 API for the recent
libressl version.
Fixes: 2c192b6916 ("tools/libressl: update to version 2.7.2")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
When libressl was linked the libpthread was missing, add it in addition.
Fixes: 2c192b6916 ("tools/libressl: update to version 2.7.2")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Added for convenience. These boards can be used as dev boards running
various operating systems from different media, and this simplifies work
with U-Boot environment.
Signed-off-by: Damir Samardzic <damir.samardzic@sartura.hr>
* QCA IPQ4019
* 256 MB of RAM
* 32 MB of SPI NOR flash (s25fl256s1)
- 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=20,variant=OM-A62
* 2T2R 5 GHz (channel 36-64)
- QCA9888 hw2.0 (PCI)
- requires special BDF in QCA9888/hw2.0/board-2.bin
bus=pci,bmi-chip-id=0,bmi-board-id=16,variant=OM-A62
* 2T2R 5 GHz (channel 100-165)
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=21,variant=OM-A62
* multi-color LED (controlled via red/green/blue GPIOs)
* 1x button (reset; kmod-input-gpio-keys compatible)
* external watchdog
- triggered GPIO
* 1x USB (xHCI)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
- phy@mdio3:
+ Label: Ethernet 1
+ gmac0 (ethaddr) in original firmware
+ 802.3at POE+
- phy@mdio4:
+ Label: Ethernet 2
+ gmac1 (eth1addr) in original firmware
+ 18-24V passive POE (mode B)
* powered only via POE
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.
The initramfs image can be started using
setenv bootargs 'loglevel=8 earlycon=msm_serial_dm,0x78af000 console=ttyMSM0,115200 mtdparts=spi0.0:256k(0:SBL1),128k(0:MIBIB),384k(0:QSEE),64k(0:CDT),64k(0:DDRPARAMS),64k(0:APPSBLENV),512k(0:APPSBL),64k(0:ART),64k(0:custom),64k(0:KEYS),15552k(inactive),15552k(inactive2)'
tftpboot 0x84000000 openwrt-ipq40xx-openmesh_a62-initramfs-fit-uImage.itb
set fdt_high 0x85000000
bootm 0x84000000
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Several changes has been made:
+ AES support has been removed by
upstream commit c6831c7 (2017-11-14)
[remove patch "200-fw_env_no_aes.patch"]
+ Support for UBI volumes has beed added by
upstream commit 34255b9 (2017-11-15)
[remove patch "300-support-env-in-ubivol-chardev.patch"]
+ A command line argument has beed added ("-c") to manually indicate
the location of the environment configuration file
Also, patch "400-u-boot-2015.10-stdint.patch" is no longer
necessary, and the config option to enable UBI support has
been removed.
Size comparisons:
fw_printenv size:
Target Before After
ar71xx 15,189 bytes 18,133 bytes (+2,944 bytes)
ipq40xx 20,873 bytes 20,987 bytes (+114 bytes)
mvebu 20,881 bytes 20,991 bytes (+110 bytes)
ramips 15,128 bytes 18,072 bytes (+2,944 bytes)
OPKG package size:
Target Before After
ar71xx 11,309 bytes 12,875 bytes (+1,566 bytes)
ipq40xx 11,772 bytes 13,299 bytes (+1,527 bytes)
mvebu 11,609 bytes 13,114 bytes (+1,505 bytes)
ramips 10,975 bytes 12,503 bytes (+1,528 bytes)
Compile tested: ipq40xx (musl, glibc, gcc5-musl), ar71xx, mvebu, ramips
Run tested: ipq40xx (ASUS RT-AC58U)
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
The serial was working before, but not when doing copy&pasting longer
commands in a short time.
Fixes: a4def18f29 ("uboot-omap: Update to u-boot v2017.01")
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
This release brings various improvements to clearfog support, such as distro-boot.
Obsoletes:
0002-clearfog-reset-usom-onboard-1512-phy.patch
0003-clearfog-enable-distro-boot-code.patch
Signed-off-by: Josua Mayer <josua.mayer97@gmail.com>
CONFIG_* variables can easily be set by overriding Build/Configure.
so set NET_RANDOM_ETHADDR=y and CMD_SETEXPR=y here.
This replaces the following patches:
0001-clearfog-generate-random-MAC-address.patch
0004-clearfog-enable-setexpr-command-by-default.patch
Signed-off-by: Josua Mayer <josua.mayer97@gmail.com>
We use the dtc from the kernel and that does not have all the options
which u-boot would like to use now. make these parameters optional.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
[wigyori@uid0.hu: renamed to 221-compatible-old-dtc.patch from 220-]
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
U-Boot now requires GCC > 5
Catch up with upstream and move some configuration options from
the header files to the corresponding defconfig files.
Also move some options of patch 010 affecting the whole platform
to 010's device only.
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
Use the UBOOT_MAKE_FLAGS defined in include/u-boot.mk and do not
overwrite them to compile the host tools against the shipped LibreSSL.
In addition add a patch to fix a compile problem when compiling the
tools against LibreSSL caused by differences in the API between OpenSSL
1.1 and LibreSSL.
This should fix the compile problems seen in build bot from time to time
by not depending on the host libssl-dev package any more but using the
LibreSSL version from OpenWrt.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Backport the compiler support patches from upstream u-boot to this older
version to make it compile with GCC 7.
This was found by build bot.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Adds support for the Turris Omnia and builds an eMMC sysupgrade image in
the same format as the SolidRun ClearFog.
An initramfs image in the simple yet Omnia-specific 'medkit' image format
is also built in order to ease the initial flashing process.
Notable hardware support omissions are support for switching between SFP
cage and copper PHY, and RGB LED control.
Due to a current limitation of DSA, only 1/2 CPU switch uplinks are used.
Specifications:
- Marvell Armada 385 1.6GHz dual-core ARMv7 CPU
- 1GB DDR3 RAM
- 8GB eMMC Flash
- 5x Gigabit LAN via Marvell 88E6176 Switch (2x RGMII CPU ports)
- 1x switchable RJ45 (88E1514 PHY) / SFP SGMII WAN
- 2x USB 3.0
- 12x dimmable RGB LEDs controlled by independent MCU
- 3x Mini PCIe slots
- Optional Compex WLE200N2 Mini PCIe AR9287 2x2 802.11b/g/n (2.4GHz)
- Optional Compex WLE900VX Mini PCIe QCA9880 3x3 802.11ac (2.4 / 5GHz)
- Optional Quectel EC20 Mini PCIe LTE modem
Flash instructions:
If the U-Boot environment has been modified previously (likely manually via
serial console), first use serial to reset the default environment.
=> env default -a
=> saveenv
Method 1 - USB 'medkit' image w/o serial
- Copy openwrt-mvebu-turris-omnia-sysupgrade.img.gz and
omnia-medkit-openwrt-mvebu-turris-omnia-initramfs.tar.gz to the root of a
USB flash drive formatted with FAT32 / ext2/3/4 / btrfs / XFS.
Note that the medkit MUST be named omnia-medkit*.tar.gz
- Disconnect other USB devices from the Omnia and connect the flash drive
to either USB port.
- Power on the Omnia and hold down the rear reset button until 4 LEDs are
illuminated, then release.
- Wait approximately 2 minutes for the Turris Omnia to flash itself with
the temporary image, during which LEDs will change multiple times.
- Connect a computer to a LAN port of the Turris Omnia with a DHCP client
- (if necessary) ssh-keygen -R 192.168.1.1
- ssh root@192.168.1.1
$ mount /dev/sda1 /mnt
$ sysupgrade /mnt/openwrt-mvebu-turris-omnia-sysupgrade.img.gz
- Wait another minute for the final OpenWrt image to be flashed. The Turris
Omnia will reboot itself and you can remove the flash drive.
Method 2 - TFTP w/ serial
- Extract omnia-medkit-openwrt-mvebu-turris-omnia-initramfs.tar.gz and copy
dtb + zImage to your TFTP server (rename if desired)
- Connect Turris Omnia WAN port to DHCP-enabled network with TFTP server
- Connect serial console and interrupt U-Boot
=> dhcp
=> setenv serverip <tftp_server_ip_here>
=> tftpboot 0x01000000 zImage
=> tftpboot 0x02000000 dtb
=> bootz 0x01000000 - 0x02000000
- OpenWrt will now boot from ramdisk
- Download openwrt-mvebu-turris-omnia-sysupgrade.img.gz to /tmp/
$ sysupgrade /tmp/openwrt-mvebu-turris-omnia-sysupgrade.img.gz
- Wait another minute for the final OpenWrt image to be flashed. The Turris
Omnia will reboot itself.
Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
Rename the gphy firmware to match the name requested by kernel 4.14 and
update the devicetree source files to use the new name.
Update the u-boot lantiq Makefile to be compatible with the new names as
well.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This syncs the Orange Pi R1 device tree files with the one from the
upstream kernel and also uses the default configuration from the Orange
Pi Zero.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
EG-200 is a DIN rail mountable device with one ethernet port, wifi,
an RS-485 port, and an internal USB attached uSD card reader.
Two leds, "modbus" and "etactica" are managed by userspace applications
in factory firmware.
Flash instruction:
Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.
Signed-off-by: Karl Palsson <karlp@etactica.com>
This prevents passing down the HOSTCC stuff set in u-boot.mk
which results in linking errors against openssl:
tools/mxsimage.o: In function `sb_aes_reinit':
mxsimage.c:(.text+0x202): undefined reference to `EVP_CIPHER_CTX_reset'
tools/mxsimage.o: In function `mxsimage_generate':
mxsimage.c:(.text+0x110d): undefined reference to `EVP_MD_CTX_new'
mxsimage.c:(.text+0x114f): undefined reference to `EVP_MD_CTX_free'
mxsimage.c:(.text+0x11c3): undefined reference to `EVP_MD_CTX_new'
mxsimage.c:(.text+0x1323): undefined reference to `EVP_MD_CTX_free'
mxsimage.c:(.text+0x134a): undefined reference to `EVP_CIPHER_CTX_reset'
tools/mxsimage.o: In function `mxsimage_verify_print_header':
mxsimage.c:(.text+0x23ce): undefined reference to `EVP_MD_CTX_new'
mxsimage.c:(.text+0x242c): undefined reference to `EVP_MD_CTX_new'
mxsimage.c:(.text+0x246b): undefined reference to `EVP_MD_CTX_free'
mxsimage.c:(.text+0x24ef): undefined reference to `EVP_CIPHER_CTX_reset'
mxsimage.c:(.text+0x2e52): undefined reference to `EVP_MD_CTX_free'
collect2: error: ld returned 1 exit status
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
ls1012ardb/ls1012afrdm/ls1046ardb/ls1088ardb firmwares now use ubifs
rootfs. So u-boot env should be set accordingly.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
With no warning, it just looks like the box has hung during boot.
We don't want users resetting it without having captured a crashdump.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
When we provide the HOSTCFLAGS to the U-Boot build it will fail because
it can not find the u-boot provided header files any more.
Just overwrite and not append the package specific configuration on top
of the configuration provided by u-boot.mk.
uboot-fritz4040 is based on U-Boot 2012.07 and this problem is probably
similar to the problem seen with the lantiq and ar71xx u-boot build.
Fixes: df9781a420 ("u-boot,at91bootstrap: fix incorrect HOSTCPPFLAGS variable")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Since I have no openssl-dev on my machine, I first
get this error:
```
tools/kwbimage.c:21:10: fatal error: openssl/bn.h: No such file or directory
#include <openssl/bn.h>
```
After removing the UBOOT_MAKE_FLAGS the next error is:
```
tools/kwbimage.c:40:6: error: conflicting types for ‘EVP_MD_CTX_cleanup’
void EVP_MD_CTX_cleanup(EVP_MD_CTX *ctx)
```
After removing the OpenSSL patches the next error is:
```
HOSTLD tools/dumpimage
/usr/bin/ld: cannot find -lssl
/usr/bin/ld: cannot find -lcrypto
collect2: error: ld returned 1 exit status
scripts/Makefile.host:108: recipe for target 'tools/dumpimage' failed
make[5]: *** [tools/dumpimage] Error 1
```
So, the final part is to add the build system's
HOST_LDFLAGS to the UBOOT_MAKE_FLAGS.
(which was done in the previous commit)
Then the image builds.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
This would should up as `$$(HOSTCPPFLAGS)` in the host CFLAGS.
```
make --jobserver-fds=3,4 -j -C <openwrt>/build_dir/target-arm_cortex-a8+vfpv3_musl_eabi/u-boot-A10-OLinuXino-Lime/u-boot-2017.07 CROSS_COMPILE=arm-openwrt-linux-muslgnueabi- DTC="<openwrt>/build_dir/target-arm_cortex-a8+vfpv3_musl_eabi/linux-sunxi_cortexa8/linux-4.9.76/scripts/dtc/dtc" HOSTCC="gcc" HOSTCFLAGS='-O2 -I<openwrt>/staging_dir/host/include -I<openwrt>/staging_dir/host/usr/include -I<openwrt>/staging_dir/hostpkg/include -I<openwrt>/staging_dir/target-arm_cortex-a8+vfpv3_musl_eabi/host/include $$(HOSTCPPFLAGS)' HOSTLDFLAGS="" BL31=<openwrt>/staging_dir/target-arm_cortex-a8+vfpv3_musl_eabi/image/bl31.bin
```
And then it would complain with:
```
/bin/sh: 1: HOSTCPPFLAGS: not found
```
Also, HOSTCPPFLAGS does not exist.
The correct var is HOST_CPPFLAGS.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
We use the dtc from the kernel and that does not have all the options
which u-boot would like to use now. make these parameters optional.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
- use release build instead of debug to reduce size
- bump to use latest commit in allwinner tree
Tested on Pine64/1G.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Use the generic board detection method:
- Board name: First compatible string from the device tree
- Board model: Model property from the device tree
Change occurrences of board name in userspace by the compatible
string, and removed target specific board detection script
Replace the definition of SUPPORTED_DEVICES in Device/Default
to extract the dt compatible string from each device definition.
Additionally, for devices supported by lede-17.01, append
the value of BOARD_NAME to SUPPORTED_DEVICES in the device
definition.
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
These packages are needed to generate the image, better mark them hidden
so we will activate them based on which boards gets build and they will
be activated always when the board which needs then gets build.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
These packages are needed to generate the image, better mark them hidden
so we will activate them based on which boards gets build and they will
be activated always when the board which needs then gets build.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The fixes following problems
1. changing prefix at91bootstrap to AT91bootstrap will fix the default
selection of at91bootstrap for the selected sama5 subtarget.
2. fixed missing default selection of sama5d4 nand flash for the
selected sama5d4 subtarget.
3. corrected at91bootstrap Title name.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
neon and VFPv4 support is added to this target and uboot-at91 build
fails due to TARGET_CFLAGS -mfloat-abi set to hard. as a fix, setting
uboot-at91 CFLAGS -mfloat-abi=soft.
Fixes: 01cc6bd495 ("at91: sama5: activate fpu")
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
add an uboot able to boot a kernel in an ubi partition
This uboot also has a "recovery" feature, before
booting from flash it will try to boot a initramfs
image called "initramfs.bin" from a FAT32-formatted
USB drive connected to the USB 2.0 port.
(u-boot lacks drivers for usb 3.0 controllers)
Just rename the initramfs image and place it on
the usb drive, the uboot will load it.
In case there is no USB drive or no such file
is found, the uboot will boot from internal flash.
The whole check takes less than a second, boot times
are not impacted.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
Use <manufacturer>_<modelname> as image name.
Use the BOARD_NAME variable to ensure that the former used boardname is
still used as the subdirectory name for the sysupgrade-tar image, to
not break sysupgrade from earlier versions.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Build the Seagate GoFlexHome u-boot for the Seagate GoFlexNet as well. The
name clearly indicates that the u-boot can be used for both boards
Build the Zyxel NSA310 u-boot if the NSA310B image is selected.
Signed-off-by: Mathias Kresin <dev@kresin.me>
No image build code for the Guruplug, Sheevaplug and NSA310S exists. Drop
support for the boards for now.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The git hash was changed for multiple layerscape packages without
changing the version number. The LEDE build system will not download the
packages again if the old version is already there and so some people
and the build bots are using wrong version of some packages. Use
PKG_SOURCE_DATE instead of PKG_VERSION to generate packages with the
date and the first charterers of the git hash. This will change the file
name and make the build system download them again, also if in future
the git hash is changed the file name will change and trigger a new
download.
This should fix a problem spotted by build bot.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The LinkIt Smart 7688/LinkIt Smart 7688 Duo are identical beside the
extra ATmega32U4 - accessible via UART - on the the Duo.
Since all relevant hardware is identical, drop the Duo special handling
in userspace.
Signed-off-by: Mathias Kresin <dev@kresin.me>
In commit 2b1ec44dbd ("layerscape: add ls1012afrdm device support")
The git revision and the mirror hash for this package was updated to a
version which includes ls1012afrdm-uboot.bin, but the file name at
dl/uboot-layerscape-armv8_32b-2017.09.tar.xz staid the same. This way
most user did not download the new version but used the old file.
Convert this package to the normal git clone parameters by using
PKG_SOURCE_DATE instated of PKG_VERSION, now the file name in dl also
contains the git hash and should change every time the git hash is
updated.
This should fix a problem spotted by build bot.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Use <manufacturer>_<modelname> as image name.
Use the BOARD_NAME variable to ensure that the former used boardname is
still used as the subdirectory name for the sysupgrade-tar image, to
not break sysupgrade from earlier versions.
While at it, normalise the image filenames by using only lower case
characters and bin as file extension for sysupgrade images.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use the first compatible string as board name in userspace. Add the new
board name as well as the former used board name to the image metadata
to keep compatibilty with already deployed installations.
Don't add the former used boardname for boards which exists only in
master or evaluation boards.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The uboot target is named MarsBoard_A10 and it was not build at all.
This fixes a build problem seen by the build bot.
Fixes: 6a3565985f ("sunxi: Added profile for HAOYU Electronics Marsboard A10")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
CPE ids helps to tracks CVE in packages.
https://cpe.mitre.org/specification/
Thanks to swalker for CPE to package mapping and
keep tracking CVEs.
Acked-by: Jo-Philipp Wich <jo@mein.io>
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
My compilation failed because of missing uint.* definitions:
In file included from mtd.h:33:0,
from bootstream.c:35:
BootControlBlocks.h:58:2: error: unknown type name 'uint8_t'
uint8_t m_u8DataSetup;
^
BootControlBlocks.h:59:2: error: unknown type name 'uint8_t'
uint8_t m_u8DataHold;
^
BootControlBlocks.h:60:2: error: unknown type name 'uint8_t'
uint8_t m_u8AddressSetup;
^
BootControlBlocks.h:61:2: error: unknown type name 'uint8_t'
uint8_t m_u8DSAMPLE_TIME;
Adding the header file fixes the problem.
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
[fold changes into 001-compile.patch]
Signed-off-by: Mathias Kresin <dev@kresin.me>
The QorIQ FRDM-LS1012A Board is an ultra-low-cost
development platform for QorIQ LS1012A Series Network
Processors built on ARM Cortex-A53 processor.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
- H3 @ 1.3 GHz
- 1GiB DDR3
- 10/100Mbps Ethernet
- Realtek RTL8189ETV wifi
- 4 USB 2.0
Difference to the "Orange Pi Plus" is the lack of Gbit ethernet
and lack of onboard flash.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
The MarsBoard was a short-lived credit-card sized, extendable board with an Allwinner A10 SoC.
http://linux-sunxi.org/MarsBoard_A10
Signed-off-by: Kayo Phoenix <kayo@illumium.org>
[Forward-ported to new target layout:]
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Upgrade uboot-kirkwood to upstream release 2017.09
Catch up with upstream and move configuration options from
simple defines to Kconfig, as otherwise dependencies would
not be resolved and code would not compile.
Tested-by: Alberto Bursi <alberto.bursi@outlook.it>
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
This backports the upstream commit fixing stale references to
CONFIG_SUNXI_GMAC which have been later replaced by CONFIG_SUN7I_GMAC.
This fixes the designware MAC pinmuxing on e.g: Lamobo R1.
Refresh patches while we are at it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
removed copying of binaries to BIN_DIR during install and using
default/install to install binaries to BIN_DIR folder.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
Added sama5 to BUILD_SUBTARGET variable.This will populate at91bootstrap
menu options in bootloader menu only when SAMA5 devices are selected as
SUBTARGET and to avoid showing up this menu when legacy device is
selected as SUBTARGET and fixed typo mistake: sama5d3 -> sama5d2.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
This fixes the following problems:
* Add BUILD_DEVICES for legacy subtarget
* Use features from u-boot.mk for sama5 subtarget This is mainly done
by changing the prefix from uboot to U-Boot. This makes them depend
on the sama5 subtarget and not selectable for the legacy subtarget
any more
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
NXP Layerscape LSDK had set up its own open source web site
and github for release.
https://lsdk.github.iohttps://github.com/qoriq-open-source
This patch is to update rcw/fman_ucode/u-boot packages with LSDK
git trees. Also add some patches of packages to support LEDE.
Since ARMv8 32-bit u-boot images are same with ARMv8 64-bit images
but 64-bit toolchain couldn't be used for 32-bit targets, we still
use a private tree for ARMv8 32-bit u-boot images. This is in plan
to move this private tree to NXP Layerscape github.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Rename subtargets 32b/64b with armv8_32b/armv8_64b which are
more proper, and update makefile files. There also will be other
subtargets added in the future, like armv7.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
This patch implements CPU frequency control as found on several
routerboard devices.
Supported SoCs:
- QCA953X
- AR9344
Tested on hAP lite and mAP lite (QCA953x): steps of 50MHz
Tested on LHG 5 (AR9344): steps of 50MHz
On unsupported hardware, this patch is a NOP: it will not alter the
new field.
"rbcfg help" will display an empty "cpu_freq" help listing.
"rbcfg show" will not show the cpu_freq field.
"rbcfg set/get cpu_freq" will return an error code.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
[adjusted subject]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The following features are working and tested:
* both Ethernet ports
* MMC
* LED
The following features are not working:
* Wifi (There is a crappy driver we could port)
* SPI flash (I haven't looked into this)
I haven't tried out the rest.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit improves support for the Xiaomi Mi Router 3G originally
added in commit 6e283cdc0d
Improvements:
- Remove software watchdog as hardware watchdog now working as per
commit 3fbf3ab44f for all mt7621
devices.
- Reset button polarity corrected - length of press determines reboot
(short press) vs. reset to defaults (long press) behaviour.
- Enable GPIO amber switch port LEDs on board rear - lit indicates 1Gbit
link and blink on activity. Green LEDs driven directly by switch
indicating any link speed and tx activity.
- USB port power on/off GPIO exposed as 'usbpower'
- Add access to uboot environment settings for checking/setting uboot
boot order preference from user space.
Changes:
- Front LED indicator is physically made of independent Yellow/Amber,
Red & Blue LEDs combined via a plastic 'lightpipe' to a front panel
indicator, hence the colour behaviour is similar to an RGB LED. RGB
LEDs are not supported at this time because they produce colour results
that do not then match colour labels, e.g. enabling 'mir3g:red' and
'mir3g:blue' would result in a purple indicator and we have no such
label for purple.
The yellow, red & blue LEDs have been split out as individual yellow,
red & blue status LEDs, with yellow being the default status LED as
before and with red's WAN and blue's USB default associations removed.
- Swapped order of vlan interfaces (eth0.1 & eth0.2) to match stock vlan
layout. eth0.1 is LAN, eth0.2 is WAN
- Add 'lwlll' vlan layout to mt7530 switch driver to prevent packet
leakage between kernel switch init and uci swconfig
uboot behaviour & system 'recovery'
uboot expects to find bootable kernels at nand addresses 0x200000 &
0x600000 known by uboot as "system 1" and "system 2" respectively.
uboot chooses which system to hand control to based on 3 environment
variables: flag_last_success, flag_try_sys1_failed & flag_try_sys2_failed
last_success represents a preference for a particular system and is set
to 0 for system 1, set to 1 for system 2. last_success is considered *if*
and only if both try_sys'n'_failed flags are 0 (ie. unset) If *either*
failed flags are set then uboot will attempt to hand control to the
non failed system. If both failed flags are set then uboot will check
the uImage CRC of system 1 and hand control to it if ok. If the uImage
CRC of system is not ok, uboot will hand control to system 2
irrespective of system 2's uImage CRC.
NOTE: uboot only ever sets failed flags, it *never* clears them. uboot
sets a system's failed flag if that system's was selected for boot but
the uImage CRC is incorrect.
Fortunately with serial console access, uboot provides the ability to
boot an initramfs image transferred via tftp, similarly an image may
be flashed to nand however it will flash to *both* kernels so a backup
of stock kernel image is suggested. Note that the suggested install
procedure below set's system 1's failed flag (stock) thus uboot ignores
the last_success preference and boots LEDE located in system 2.
Considerable thought has gone into whether LEDE should replace both
kernels, only one (and which one) etc. LEDE kernels do not include a
minimal rootfs and thus unlike the stock kernel cannot include a
method of controlling uboot environment variables in the event of
rootfs mount failure. Similarly uboot fails to provide an external
mechanism for indicating boot system failure.
Installation - from stock.
Installation through telnet/ssh:
- copy lede-ramips-mt7621-mir3g-squashfs-kernel1.bin and
lede-ramips-mt7621-mir3g-squashfs-rootfs0.bin to usb disk or wget it
from LEDE download site to /tmp
- switch to /extdisks/sda1/ (if copied to USB drive) or to /tmp if
wgetted from LEDE download site
- run: mtd write lede-ramips-mt7621-mir3g-squashfs-kernel1.bin kernel1
- run: mtd write lede-ramips-mt7621-mir3g-squashfs-rootfs0.bin rootfs0
- run: nvram set flag_try_sys1_failed=1
- run: nvram commit
- run: reboot
Recovery - to stock.
Assuming you used the above installation instructions you will have a
stock kernel image in system 1. If it can be booted then it may be used
to perform a stock firmware recovery, thus erasing LEDE completely. From
a 'working' LEDE state (even failsafe)
Failsafe only:
- run: mount_root
- run: sh /etc/uci-defaults/30_uboot-envtools
Then do the steps for 'All'
All:
- run: fw_setenv flag_try_sys2_failed 1
- run: reboot
The board will reboot into system 1 (stock basic kernel) and wait with
system red light slowly blinking for a FAT formatted usb stick with a
recovery image to be inserted. Press and hold the reset button for
around 1 second. Status LED will turn yellow during recovery and blue
when recovery complete.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Fixes the following build issue: "undefined reference to `EVP_MD_CTX_create'"
From: Jelle van der Waa <jelle@vdwaa.nl>
The rsa_st struct has been made opaque in 1.1.x, add forward compatible
code to access the n, e, d members of rsa_struct.
EVP_MD_CTX_cleanup has been removed in 1.1.x and EVP_MD_CTX_reset should be
called to reinitialise an already created structure.
Signed-off-by: Marko Ratkaj <marko.ratkaj@sartura.hr>
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
[replaced u-boot patch with original version from u-boot git]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The arm-trusted-firmware-sunxi package is only used by the Allwinner
A64, so only make it selectable for its subtarget sunxi/cortexa53.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Jonas Gorski <jonas.gorski@gmail.com>
at91bootstrap is a second-level bootloader for Microchip(Atmel AT91) SoCs.
It provides a set of algorithms to manage the hardware initialization and
to download the main application or a third-level bootloader(i.e. uboot)
from specified boot media to main memory and execute it.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
Add support for SAMA5D4 Xplained board and options to select & build
u-boot configs for different media storage.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
Add support for SAMA5D2 Xplained board and options to select & build
u-boot configs for different media storage.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
Add support for SAMA5D3 Xplained board and options to select & build
u-boot configs for different media storage.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
IPQ806x AP148 and DB149 boards didn't have the UCI ubootenv
section initialized, so the usage of fw_printenv required manual
configuration. With this change, the "fw_printenv" and "fw_setenv"
command will automatically work on NOR and NAND based platforms.
Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
Backing up the current firmware from U-Boot over serial can take hours.
Booting a working Linux image for backup purposes is not always an option.
Using the tftpput command in U-Boot is the fastest and easiest way.
tftpput will upload the contents of a memory region to the TFTP server.
The IP address of the server is stored in the serverip variable.
Usage:
tftpput <memaddr> <length> <filename>
Example for a complete flash backup of an o2 Box 6431 (VGV7510KW22):
VGV7510KW22 # tftpput 0xB0000000 0x1000000 o2boxbackup.bin
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
split kexec-tools into two packages, kexec and kdump.
* kexec to simply execute a new kernel
* kdump is for loading and collecting debris of a crashed kernel with
support for kdump forensics.
In order to properly support booting into a crashkernel, an init script
as well as UCI configuration has been added.
As modifying the kernel cmdline is required for this to work in x86
platforms use an uci-defaults script to modify /boot/grub/grub.cfg.
To test collecting crash information, use the 'c' sysrq-trigger, ie.
echo c > /proc/sysrq-trigger
This should result in the crash kernel being executed and (depending
on the configution) dmesg and/or vmcore getting saved.
To check if the crash kernel was loaded properly, use the 'status'
command of the kdump init script.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
EnGenius ENS202EXT is an outdoor wireless access point with
2-port 10/100 switch, detachable antennas and proprietery PoE.
The device is based on Qualcomm/Atheros AR9341 v1.
Specifications:
- 535/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM
- 16 MB of FLASH
- UART (J1) header on PCB (unpopulated)
- 2x 10/100 Mbps Ethernet
- 2.4 GHz, up to 26dBm
- 2x external, detachable antennas
- 7x LED, 1x button
Flash instructions:
You have three options:
- Use the vendor firmware upgrade page on the web interface and give
it the factory.img. This is the easiest way to go about it.
- If you have serial access during u-boot, interrupt the normal boot
(any key before timeout) and run 'run failsafe_boot'; this will bring
you to a minimal openwrt luci image on ip 192.168.1.1 useful if you've
bricked the normal firmware.
- Use the vendor's management cli, which can be accessed via telnet
with the same credentials as the web login (default admin:admin), then
issue the following commands:
*** Hi admin, welcome to use cli(V-1.6.7) ***
---========= Commands Help =========---
stat -- Status
sys -- System
wless2 -- 2.4G-Wireless
mgmt -- Management
tree -- Tree
help -- Help
reboot -- Reboot
ens202ext>mgmt
Management
---========= Commands Help =========---
admin -- Administration
mvlan -- Management VLAN settings
snmp -- SNMP settings
backup -- Backup/Restore settings
autorb -- Auto reboot settings
fwgrade -- Firmware upgrade
time -- Time settings
wifisch -- Wifi schedule
log -- Log
diag -- Diagnostics
disc -- Device Discovery
logout -- Logout
help -- Help
exit -- Exit
ens202ext/mgmt>fwgrade
Management --> Firmware upgrade
---========= Commands Help =========---
fwup -- Firmware upgrade
help -- Help
exit -- Exit
ens202ext/mgmt/fwgrade>fwup http://web.server/lede-ar71xx-generic-ens202ext-squashfs-factory.bin
Signed-off-by: Marty Plummer <ntzrmtthihu777@gmail.com>
Add a patchfile that implements distro-boot and is meant to go upstream
Also make the other patches git-am'able for easier maintenance.
Signed-off-by: Josua Mayer <josua.mayer97@gmail.com>
Add support for SolidRun ClearFog Base board.
The base model is a smaller version of ClearFog Pro without
the DSA switch, replacing it with a second copper gigabit
port, and only one PCIe socket.
Signed-off-by: Marko Ratkaj <marko.ratkaj@sartura.hr>
Even it's unknown if it's booting with thumb, because the lack of hardware.
Enable it for now, so the build succeed, because without thumb it can not fit
into spl.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
The beagleboard doesn't boot with Thumb enabled, but without Thumb the
SPL (first stage bootloader) is too big to fit into SRAM.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Use fixed led names and add each board variant instead of manipulating
the board name.
It makes the ramips board name function less different to the one used
in other targets and allows to merge them with a common function.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Couple of important upstream patches (slated for 2.0.15) that
are necessary for kexec to run on MUSL and on x86 hardware.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
With upstream changes, the last update to U-Boot 2017.03
broke the nsa310 and nsa325 targets. Also fix some redefines.
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
The Pistachio target is a MIPS interaptiv based SoC developed by
Imagination Technologies. It includes blocks for i2c, spi, audio,
usb and WiFi.
This also adds the base support for the 'Creator Ci40 (marduk)'
device which uses the Pistachio SoC to create an IoT hub by
including Bluetooth, WiFi and 6lowpan on one board. Additionally 2x
Mikrobus ports are available to expand with further RF technologies
or add sensors. You can find out more here http://creatordev.io.
Note, this commit is just the initial board support hence the
following are not expected to work yet:
* WiFi
* Bluetooth
* 6lowpan
* Audio
* Mikrobus uarts, user leds (clock dependency of 6lowpan chip)
The aim of this commit is to essentially have the same level of
support that currently exists in the mainline kernel.
Signed-off-by: Abhijit Mahajani <Abhijit.Mahajani@imgtec.com>
Signed-off-by: Francois Berder <francois.berder@imgtec.com>
Signed-off-by: Ian Pozella <Ian.Pozella@imgtec.com>
Signed-off-by: Mayank Sirotiya <Mayank.Sirotiya@imgtec.com>
Signed-off-by: Sean Kelly <Sean.Kelly@imgtec.com>
Backport kernel patches for LS1043A Rev1.1 support from upstream,
patchwork, and SDK. And update to latest u-boot to support LS1043A
Rev1.1.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
This is needed for the definition of $(LINUX_DIR). This is used in
u-boot.mk to change the device-tree compiler to the dtc used by
linux.
Without this, the build will use the system dtc. This results in a
build failure when a dtc does not exist outside the buildroot.
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Specifying USE_PRIVATE_LIBGCC is no longer needed, as it is the
default.
Patch 001 is removed, since it was already merged upstream. Patches
100 and 101 are removed because they do not appear to be needed
anymore, and they do not conform with the sign-off and commit message
procedures.
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Because they were hidden, there was no way to disable the uboot
targets in menuconfig, so they had to be built every time. The omap
target is the only one to hide uboot packages. To be consistent with
the other targets, and have more control over the build, un-hide the
u-boot packages.
Note that the default behavior remains unchanged, as uboot will be
built unless explicitly disabled.
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
fixes issue "nsa 310b u-boot can initialize usb but cannot
use usb storage so it cannot load files from usb"
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
Goflexhome/net use uImage, and to boot an uImage the u-boot
must use bootm command, not bootz.
Fixes the "i cannot boot LEDE with this u-boot" issue that I
found out myself with my goflexnet.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
all patches for CONFIG_SYS_GENERIC_BOARD are obsolete for
uboot 2016 sources.
Run-tested with the uboot of goflexnet, also the md5sum of
all other uboots is the same with or without these patches.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
Do not put the apex images into the kernel build directory as this directory
might get removed after kernel updates while the apex packages InstallDev
recipe is not getting re-executed because it is still considered current,
leading to image build failures later on due to missing images.
To ensure that built bootloader images persist over kernel version updates in
the buildroot, put them into the new STAGING_DIR_IMAGE directory.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Do not put the u-boot images into the kernel build directory as this directory
might get removed after kernel updates while the u-boot packages InstallDev
recipe is not getting re-executed because it is still considered current,
leading to image build failures later on due to missing images.
To ensure that built bootloader images persist over kernel version updates in
the buildroot, put them into the new STAGING_DIR_IMAGE directory.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Do not put the u-boot images into the kernel build directory as this directory
might get removed after kernel updates while the u-boot packages InstallDev
recipe is not getting re-executed because it is still considered current,
leading to image build failures later on due to missing images.
To ensure that built bootloader images persist over kernel version updates in
the buildroot, put them into the new STAGING_DIR_IMAGE directory.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Do not put the u-boot images into the kernel build directory as this directory
might get removed after kernel updates while the u-boot packages InstallDev
recipe is not getting re-executed because it is still considered current,
leading to image build failures later on due to missing images.
To ensure that built bootloader images persist over kernel version updates in
the buildroot, put them into the new STAGING_DIR_IMAGE directory.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Do not put the u-boot and ucode images into the kernel build directory as this
directory might get removed after kernel updates while the u-boot packages
InstallDev recipe is not getting re-executed because it is still considered
current, leading to image build failures later on due to missing images.
To ensure that built bootloader images persist over kernel version updates in
the buildroot, put them into the new STAGING_DIR_IMAGE directory.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Do not put the u-boot images into the kernel build directory as this directory
might get removed after kernel updates while the u-boot packages InstallDev
recipe is not getting re-executed because it is still considered current,
leading to image build failures later on due to missing u-boot images.
To ensure that built bootloader images persist over kernel version updates in
the buildroot, put them into the new STAGING_DIR_IMAGE directory.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
All SPL variants are lzo compressed. The lzop binary is used for
compression but is not available in tools.
Additionally at least the NAND SPL support is broken and doesn't create
working bootloaders.
The fb3370 SPI NOR SPL enabled u-boot isn't required for LEDE since the
LEDE images are targeting the pre-installed EVA bootloader.
Mark these u-boot variants as well as the SPL variants for the
reference boards as broken till the lzma issues are fixed upstream and
we can use lzma instead of lzo compression.
Signed-off-by: Mathias Kresin <dev@kresin.me>
accessing the u-boot's envs on this device is required to read the mac address.
These are the envs of the new u-boot, not of the stock one.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
Instead of referencing u-boot packages from device profiles and having a
-all metapackage, make the u-boot packages hidden (they don't install to
bin/ anyway), and name the files in KERNEL_BUILD_DIR appropriately
Signed-off-by: Felix Fietkau <nbd@nbd.name>
this commit allows to make a standalone u-boot for nsa310b.
While both first-stage and second-stage u-boot work fine if
installed to flash or loaded with kwboot,
I could not get stock u-boot nor bodhi's u-boot to chainload
any second stage u-boot (I also tried with dockstar's uboot
that works fine on this device if loaded with kwboot).
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
While at it, the following changes are introduced
- Rewrite the Makefile for better readability
- Make parallel builds possible
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Increasing CONFIG_SYS_BOOTM_LEN from 8 MB to 16 MB is necessary to
support uncompressing images larger than 8 MB when using the bootm
command.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This seems to occur when gettext-full is built on the host-side
and the autoreconf stuff re-generates some of the build files,
except for the po/Makefile.in.in
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Even though these fonts may not be installed, they seem to be
generated at build time.
Seems that the configure script re-generated from configure.ac
is a bit more annoying than it has to be.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Reboot of: a0ea22ac43
Reverted: 3c52cbfa53
The host-side build of grub2 requires this sometimes.
This will re-generate the ./configure script from configure.ac.
I don't know the conditions of how this reproduces, it just
sometimes appears, and sometimes doesn't.
Build error
```
<lede-dir>/build_dir/target-x86_64_musl-1.1.15_yogi/host/grub-2.02~beta2/build-aux/missing: line 81: aclocal-1.14: command not found
WARNING: 'aclocal-1.14' is missing on your system.
You should only need it if you modified 'acinclude.m4' or
'configure.ac' or m4 files included by 'configure.ac'.
The 'aclocal' program is part of the GNU Automake package:
<http://www.gnu.org/software/automake>
It also requires GNU Autoconf, GNU m4 and Perl in order to run:
<http://www.gnu.org/software/autoconf>
<http://www.gnu.org/software/m4/>
<http://www.perl.org/>
Makefile:3962: recipe for target 'aclocal.m4' failed
```
Adding PKG_FIXUP adds sanity (i.e. autoreconf is used for host & target
builds) over just using HOST_FIXUP.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Few minor code formatting style fixes, including:
- keep one board per line
- always use "|\" (for consistency)
- remove redundant double quotes and empty lines
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Add support for NXP layerscape ls1046ardb 64b/32b Dev board.
LS1046ARDB Specification:
-------------------------
Memory subsystem:
* 8GByte DDR4 SDRAM (64bit bus)
* 512 Mbyte NAND flash
* Two 64 Mbyte high-speed SPI flash
* SD connector to interface with the SD memory card
* On-board 4G eMMC
Ethernet:
* Two XFI 10G ports
* Two SGMII ports
* Two RGMII ports
PCIe:
* PCIe1 (SerDes2 Lane0) to miniPCIe slot
* PCIe2 (SerDes2 Lane1) to x2 PCIe slot
* PCIe3 (SerDes2 Lane2) to x4 PCIe slot
* USB 3.0: one super speed USB 3.0 type A port, one Micro-AB port
* UART: supports two UARTs up to 115200 bps for console
Signed-off-by: Yutang Jiang <yutang.jiang@nxp.com>
In order to prevent the impact of the merger of the company and the potential
rebase of the SDK repositories, migrate the u-boot source to github.
Signed-off-by: Yutang Jiang <yutang.jiang@nxp.com>
Based on the submission to the uboot-lantiq repo by Martin Blumenstingl.
Use the ddr_settings.h from the GPL tarball. The NAND boot optimized
one (with memory tuning enabled) doesn't work for the UART boot image.
Use the same mtd layout as the stock u-boot. Add add UBI support.
Use the leds to indicate boot status like it is done with the stock
u-boot. Switch on the red power led if kernel image can't be loaded.
Otherwise switch the green led on.
Make only the ramboot u-boot available. Only this image is required for
the first installation of LEDE.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The host-side build of grub2 requires this sometimes.
This will re-generate the ./configure script from configure.ac.
I don't know the conditions of how this reproduces, it just
sometimes appears, and sometimes doesn't.
Build error
```
<lede-dir>/build_dir/target-x86_64_musl-1.1.15_yogi/host/grub-2.02~beta2/build-aux/missing: line 81: aclocal-1.14: command not found
WARNING: 'aclocal-1.14' is missing on your system.
You should only need it if you modified 'acinclude.m4' or
'configure.ac' or m4 files included by 'configure.ac'.
The 'aclocal' program is part of the GNU Automake package:
<http://www.gnu.org/software/automake>
It also requires GNU Autoconf, GNU m4 and Perl in order to run:
<http://www.gnu.org/software/autoconf>
<http://www.gnu.org/software/m4/>
<http://www.perl.org/>
Makefile:3962: recipe for target 'aclocal.m4' failed
```
Adding PKG_FIXUP adds sanity (i.e. autoreconf is used for host & target
builds) over just using HOST_FIXUP.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
The current uboot default config for the A13 SOM erroneously enables support
for the AXP209 power regulator IC which is not present on the board.
This superfluous support module sets an incorrect initial clock frequency and
confuses the kernel, ultimately leading to a boot failure later on.
Properly disable the PMIC support and enable the EHCI support by translating
the deprecated SYS_EXTRA_OPTIONS values into proper SUNXI_NO_PMIC and
USB_EHCI_HCD symbols respectively.
Also rename 002-add-olimex-a13-som.diff to 002-add-olimex-a13-som.patch and
refresh the remaining patches of the series while we're at it.
Reported-by: Mario Fischer <mario-fischer@web.de>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The QorIQ LS1012A processor, optimized for battery-backed or
USB-powered, integrates a single ARM Cortex-A53 core with a hardware
packet forwarding engine and high-speed interfaces to deliver
line-rate networking performance.
QorIQ LS1012A Reference Design System (LS1012ARDB) is a high-performance
development platform, with a complete debugging environment.
The LS1012ARDB board supports the QorIQ LS1012A processor and is
optimized to support the high-bandwidth DDR3L memory and
a full complement of high-speed SerDes ports.
LEDE/OPENWRT will auto strip executable program file while make. So we
need select CONFIG_NO_STRIP=y while make menuconfig to avoid the ppfe network
fiemware be destroyed, then run make to build ls1012ardb firmware.
The fsl-quadspi flash with jffs2 fs is unstable and arise some failed message.
This issue have noticed the IP owner for investigate, hope he can solve it
earlier. So the ls1012ardb now also provide a xx-firmware.ext4.bin as default
firmware, and the uboot bootcmd will run wrtboot_ext4rfs for "rootfstype=ext4"
bootargs.
Signed-off-by: Yutang Jiang <yutang.jiang@nxp.com>
Add support for NXP layerscape ls1043ardb 64b/32b Dev board.
LS1043a is an SoC with 4x64-bit up to 1.6 GHz ARMv8 A53 cores.
ls1043ardb support features as: 2GB DDR4, 128MB NOR/512MB NAND, USB3.0, eSDHC,
I2C, GPIO, PCIe/Mini-PCIe, 6x1G/1x10G network port, etc.
64b/32b ls1043ardb target is using 4.4 kernel, and rcw/u-boot/fman images from
NXP QorIQ SDK release.
All of 4.4 kernel patches porting from SDK release or upstream.
QorIQ SDK ISOs can be downloaded from this location:
http://www.nxp.com/products/software-and-tools/run-time-software/linux-sdk/linux-sdk-for-qoriq-processors:SDKLINUX
Signed-off-by: Yutang Jiang <yutang.jiang@nxp.com>
Fix the default value for the 'bootcmd' environment variable.
Therefore make the default bootcmd work for buildbot's images.
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
Fix metadata scan failure in the grub2 package by removing an unexpected
invisible space character and by adding back the missing SECTION variable
which was removed with d140648.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
While enable zynq uboot:
CONFIG_PACKAGE_uboot-zynq-zc702
CONFIG_PACKAGE_uboot-zynq-zed
CONFIG_PACKAGE_uboot-zynq-zybo
make will arise dtc error:
./scripts/dtc-version.sh: line 17: dtc: command not found
./scripts/dtc-version.sh: line 18: dtc: command not found
*** Your dtc is too old, please upgrade to dtc 1.4 or newer
make[4]: *** [checkdtc] Error 1
Pass the kernel dtc to uboot for compile.
Signed-off-by: Yutang Jiang <yutang.jiang@nxp.com>
because boot loaders are in Boot Loaders, not in Utilities -> Boot Loaders
Also moved brub2-editenv in Utilities -> Boot Loaders
Part of a wider housekeeping effort on the packages repository.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
Boot Loaders submenu of Utilities is the most logical place to find fconfig and other bootloader tools.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
