Apart from the wireless chip, the WNDR3700 v4 and the WNDR4300
is the same device. Indicate this in the kernel files.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40479
The 5V power of the USB is controlled by a GPIO pin of
the external WiFi chip. Setup the GPIO bitmasks in the
platform data of the WiFi chip to ensure that the 5V
power gets enabled by the ath9k driver.
Based on the the WNDR3700v4 support patch from Ralph Perlich:
http://patchwork.openwrt.org/patch/4763/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40478
Based on the the WNDR3700v4 support patch from Ralph Perlich:
http://patchwork.openwrt.org/patch/4763/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40477
Based on the the WNDR3700v4 support patch from Ralph Perlich:
http://patchwork.openwrt.org/patch/4763/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40475
The bootloader does not initializes the output function
correctly for all LEDs. DO that from the board setup code.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40474
The hardware manual says amber so change the color part of
the LED names to reflect that. Also update the constant names.
Based on the the WNDR3700v4 support patch from Ralph Perlich:
http://patchwork.openwrt.org/patch/4763/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40473
Adds support for the received signal strength indicator LEDs of the
Bullet M, Nanostation M and Rocket M devices.
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Patchwork: http://patchwork.openwrt.org/patch/5108/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40471
Move the comments out from the shell script to fix build
breakage introduced in r40464.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40466
The C7v2 has 16 MB flash and QCA9880-BR4A rev 2 supported by ath10k driver.
The C7v1 had 8 MB flash and the unsupported QCA9880-AR1A rev 1.
Signed-off-by: Adam Serbinski <adam@serbinski.com>
Patchwork: http://patchwork.openwrt.org/patch/5071/
[juhosg:
- remove the v2 specific profile add the ath10k driver to the existing
Archer C7 profile instead. Although on v1 devices it does not change
the non-working behaviour, but the ath10k driver is useful for users
whom have replaced the wifi card with a supported one in their units.
- update image/Makefile to build firmware image for both boards if the
Archer C7 profile is selected]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40463
Everything seems to be working fine. Potential issues:
* VLAN port IDs are reversed with regard to the numbers on the case.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 40400
I don't have access to the specs, so I'm not sure about every detail, but I
haven't seen any problems with my test system, a TL-WR841N v9. It looks pretty
much like a QCA955x without PCI, a little twist in the clock calculation and
a AR9331-compatible switch.
Features not yet supported:
* EHCI (my test system doesn't have USB)
* ? (I have no idea if the QCA953x has any other features I don't know about
that aren't used by the TL-WR841N v9)
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 40399
The version of TL-WDR4300 sold in Israel comes with a different
hardware id.
Patch-by: Daniel <daniel@makrotopia.org>
Patchwork: http://patchwork.openwrt.org/patch/5001/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40038
Patch-by: Lars Bøgild Thomsen <lth@cow.dk>
Patchwork: http://patchwork.openwrt.org/patch/4922/
[juhosg: use correct board name in uci-defaults/02_network]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40033
Patch-by: Lars Bøgild Thomsen <lth@cow.dk>
Patchwork: http://patchwork.openwrt.org/patch/4922/
[juhosg:
- use a separate patch for kernel changes,
- reorder Kconfig and Makefile entries,
- change function and variable names to be lowercase only
and fix misaligned tabs in mach-gs-oolite.c,
... ]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40032
The flash address passed to rb_init_info() is bogus,
use the predefined AR71XX_SPI_BASE macro instead.
Compile tested only.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39891
sizeof(array_from_function_definition) gives back the size of the pointer.
sizeof(type) * array_size should be used in memset.
Signed-off-by: David Völgyes <david.volgyes@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/4950/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39890
The ar71xx platform always uses the eth0 interface to provide
access to the device in failsafe mode. Due to this, failsafe
access is broken on devices where the LAN ports are connected
to the 'eth1' interface.
Update the relevant script to correctly set the ifname variable
for these devices.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39752
The RB91x boards are using a serial shift register
connected to the SPI bus to drive some of the LEDs.
Rework the board setup code to register a SPI device
for that. This makes it possible to use the 'spi-74x164'
driver to control the device.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39703
That will be used to drive the 74HC595 serial-in/parallel-out
8-bits shift register which can be found on some RouterBOARDs.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39702
The serial flash devices used on the ROuterBOARDs are
supporting 4KiB erase blocks. Enable the small sector
erase option in the m25p80 driver to avoid superfluous
erase/write of adjacent blocks.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39696
I noticed that the patch at http://patchwork.openwrt.org/patch/4017/
for adding support for the MikroTik RouterBOARD 951Ui-2HnD had been
abandoned because it wasn't generated and sent to the mailing list
correctly and doesn't apply as a result. I have cleaned up this patch.
When testing this on real hardware, I also noticed that wireless didn't
work, so this patch fixes that as well.
This patch applies cleanly to SVN 39392.
Signed-off-by: Matthew Reeve <mreeve@tenxnetworks.com>
Patchwork: http://patchwork.openwrt.org/patch/4773/
[juhosg:
- drop the 'rb951ui_wlan_init' function and rework the code to
use the recently introduced rb95x_wlan_init function instead,
- fix GPIO number of the port5 LED,
- rename LEDs according to the standard LED naming conventions,
and use 'rb' prefix in the names]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39641
Patch-by: TenNinjas <tenninjas@tenninjas.ca>
Patchwork: http://patchwork.openwrt.org/patch/4849/
[juhosg:
- use the Archer C7 specific LED setup instead of adding
identical code]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39636
This missing bit of the hack saves hugely on instruction traps
on tcp connections to ar71xx based routers.
Patch-by: Dave Taht <dave.taht@bufferbloat.net>
Patchwork: http://patchwork.openwrt.org/patch/4905/
[juhosg: adjust subject, refresh kernel patch]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39626
Solves ticket #14356 <https://dev.openwrt.org/ticket/14356>
Without this patch, UART output will show only 4 partitions:
[ 0.740000] 4 cmdlinepart partitions found on MTD device spi0.0
[ 0.750000] Creating 4 MTD partitions on "spi0.0":
[ 0.750000] 0x000000000000-0x000000050000 : "u-boot"
[ 0.760000] 0x000000050000-0x000000070000 : "u-boot-env"
[ 0.770000] 0x000000070000-0x0000007f0000 : "firmware"
[ 0.790000] 0x0000007f0000-0x000000800000 : "art"
and then linux complains :VFS: Cannot open root device "(null)"
With this patch, UART out will show 7 partitions:
[ 0.740000] 4 cmdlinepart partitions found on MTD device spi0.0
[ 0.750000] Creating 4 MTD partitions on "spi0.0":
[ 0.750000] 0x000000000000-0x000000040000 : "u-boot"
[ 0.760000] 0x000000040000-0x000000050000 : "u-boot-env"
[ 0.770000] 0x000000050000-0x0000007f0000 : "firmware"
[ 0.780000] 2 netgear-fw partitions found on MTD device firmware
[ 0.780000] 0x000000050000-0x00000014b440 : "kernel"
[ 0.790000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.800000] 0x00000014b440-0x0000007f0000 : "rootfs"
[ 0.810000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.820000] mtd: device 4 (rootfs) set to be root filesystem
[ 0.830000] 1 squashfs-split partitions found on MTD device rootfs
[ 0.830000] 0x000000340000-0x0000007f0000 : "rootfs_data"
[ 0.840000] 0x0000007f0000-0x000000800000 : "art"
This patch is tested against r39502 of trunk.
Signed-off-by: Jonathan Chang <changcs@santos.ee.ntu.edu.tw>
Patchwork: http://patchwork.openwrt.org/patch/4870/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39625
The mtdpartsize macro triggers shell errors on various Linux distributions
when the partname argument $(1) does not appear within the partmap $(2).
Change the sed pattern to only emit anything if a successful substitution
occured and only evaluate the arithmetic expression if something was printed
by the sed program.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 39583
The original dragino2 board support was missing some changes from the
upstream svn repository (http://svn.dragino.com/dragino2) that supported
sysupgrade.
[juhosg: change subject]
Signed-off-by: Karl Palsson <karlp@remake.is>
Patchwork: http://patchwork.openwrt.org/patch/4801/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39429
On recent TL-WDR4300 boards the external LNAs of the 2.4GHz
interface are connected to GPIO lines. Because these GPIO
lines are disabled by default, the RX sensitivity of the
device is quite bad.
Setup the GPIOs of the external LNAs to fix the issue.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39392
Get the size of the mtd partitions directly from the
MTD layout and remove the superfluous macro parameters.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39384
The macro checks the size of the rootfs image even if
the second parameter of the macro contains the size of
an eraseblock. It is wrong because the size of the
kernel image will be adjusted to the next eraseblock
and the resulting image might be too large.
Fix the macro to check the size of the final image
instead of the rootfs image.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39383
Since that was the last configuration in defconfig directory we can drop the
defconfig init script too.
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 39373
The eth5 LED on the RB2011 is not working because the
LED control rule is missing. Fix it.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39335
The r39147 commit introduces a regression: at lease on some routers
with ar8216 switch large packets get lost if 802.1q tagged port is
used on the interface connected to the aforementioned switch.
The r39147 changes code in the way so interface is set to accept
packets no longer than max ethernet frame length for a given mtu.
Unfortunately ar8216 has a feature: it sends two additional bytes
as a packet header and those this header needs to be added to the
max frame length. Otherwise long enough packets get lost.
The problem only manuifests itself if interface is used in vlan
tagged mode. If interface is untagged then ar8216's header fits
into space used by 802.1q tag and not packets are lost.
Include two additional bytes in the max frame length calculation
to fix the issue.
This patch is tested and works with Trendnet TEW-632BRP.
Signed-off-by Nikolay Martynov <mar.kolya@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/4656/
[juhosg:
- simplify the patch to include the additional bytes of the
switch header unconditionally,
- change subject and update commit message]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39219
The built-in wireless MAC of the AR934x SoC can handle
external LNAs and the control signal of the LNAs can be
routed to any GPIO line. Add a helper function which
can be used to configure the GPIO lines.
The helper function will be used for AR934x boards
which are using externel LNAs to improve sensitivity.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39215
The LNAs need to be enabled by setting their respective GPIO to high even
though the original firmware's setting sets them to low on initialization.
Obviously the LNAs are then later initialized by the driver on the OEM
firmware. Without this fix the device is mostly "deaf".
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Tested-by: Steven Haigh <netwiz@crc.id.au>
Patchwork: http://patchwork.openwrt.org/patch/4689/
[juhosg:
- remove the GPIO LED changes, the My Net N600 has no yellow LEDs at all,
- change subject and update the commit message]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39214
The LNAs need to be enabled by setting their respective GPIO to high even
though the original firmware's setting sets them to low on initialization.
Obviously the LNAs are then later initialized by the driver on the OEM
firmware. Without this fix the device is mostly "deaf".
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Patchwork: http://patchwork.openwrt.org/patch/4688/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39213
The hardware supports large ethernet frames. Override
the maximum frame length and packet lenght mask in the
platform data to allow to use large MTU on the ethernet
interfaces.
Limit the feature to AR934x SoCs for now. It should work
on some other SoCs as well, but those has not been tested
yet.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39149
The currently used bitmask of the maximum frame length field
is wrong for both models. On AR724x/AR933x the largest frame
size is 2047 bytes, on the AR934x it is 16383 bytes.
Make the MTU setup code model specific, and use the correct
bitmask for both models. Also change the value to the maximum.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39148
Set the MAX_FRAME_LEN register to zero in ag71xx_hw_init()
and write the correct value into that from the ag71xx_open()
and ag71xx_fast_reset() functions.
Also recalculate the RX buffer size based on the actual
maximum frame length value to optimize memory allocation.
Additionaly, disallow to change the MTU value while the
interface it running.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39147
The currently used bitmask is not correct for all SoCs.
Introduce a new field in struct ag71xx and store the
bitmask in that. Use the current value for now, it will
be adjusted for each SoCs in further patches.
Aslo use the new field directly in the ag71xx_rx_packets
and ag71xx_hard_start_xmit() functions and remove the
ag71xx_desc_pktlen() helper.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39144
Now that the switch works correctly we can enable the images for this
board.
Flashing from the factory firmware, the factory failsafe loader and
sysupgrade was tested successfully.
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Patchwork: http://patchwork.openwrt.org/patch/4617/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39130
Now that the switch is working correctly I had the chance to actually
test the LED config.
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Patchwork: http://patchwork.openwrt.org/patch/4616/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39129
The bootloader on the WD My Net N750 disables the ports on it's internal
AR8327N switch by powering them down. The stock firmware then brings the
ports back up again by starting the auto negotiation process on each
port.
This fix implements just that.
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Patchwork: http://patchwork.openwrt.org/patch/4615/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39128
This enables us to add fixups to the board specific code for boards that
require special treatment of PHYs on mdio bus reset.
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
http://patchwork.openwrt.org/patch/4614/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39127
This enables us to modify the ag71xx_mdio_platform_data from within the
board support files.
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Patchwork: http://patchwork.openwrt.org/patch/4613/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39126
Currently, the AG71XX_RX_PKT_SIZE value limits the received
frame size to 1514/1516 bytes with/without a VLAN header
respectively. However the hardware limit is controlled by
the value the AG71XX_REG_MAC_MFL register which contains
the value of the max_frame_len field.
Compute the RX buffer size from the max_frame_len field
to get rid of the 1514/1516 byte limitation. Also remove
the unused AG71XX_RX_PKT_SIZE definition.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39121
The ar7240_probe function uses the network device name
in the kernel log messages, however the name is not yet
initialized when the ar7240_probe function is called.
Use the mdio bus name in the messages to avoid ugly
log lines like the following one:
eth%d: Found an AR7240/AR9330 built-in switch
Reported-by: Ronald Wahl <ronald.wahl@raritan.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39116
The ag71xx debugfs code uses the network device name
for the device specific debugfs directory. Since r38689
'ar71xx: ag71xx: fix a race involving netdev registration'
the debugfs initialization happens before the ethernet
device gets registered and the network device name contains
'eth%d' at this point. If the board setup code registers
multiple ag71xx devices, the debugfs code tries to create
the device specific dir with the same name which causes
an error like this:
eth0: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd041, driver=Generic PHY]
ag71xx: probe of ag71xx.0 failed with error -12
Use the device name for the debugfs directory to avoid the
collisions. Also add an error message and change the return
code if the debugfs_create_dir call fails.
Reported-by: Ronald Wahl <ronald.wahl@raritan.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39115
It is only on RB911G-5HPnD and RB912UAG-5HPnD boards.
The LEDs and the USB port is not working yet.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39102
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
[juhosg: remove the image generation part until the ethernet
switch issue is resolved]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39078
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
[juhosg: use a separate patch for kernel changes]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39077
The TL-WA801ND v2 board has only one LAN port which makes
it more similar to the TL-WR[78]50RE devices. Move the
board setup code into the mach-tl-wax50re.c file.
Based-on: http://patchwork.openwrt.org/patch/4506/
Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39072
This way it is a bit easier to add other TP-LINK devices based on the
Atheros AP123 reference board with one LAN port.
Based-on: http://patchwork.openwrt.org/patch/4506/
Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39071
Patch to add the user space support for the TL-WA801ND v2
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Patchwork: http://patchwork.openwrt.org/patch/4501/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39064
Patch to add kernel support for the TP-LINK WA801ND v2
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Patchwork: http://patchwork.openwrt.org/patch/4500/
[juhosg:
- the TL-WA801ND v2 does not have a sliding switch, it uses a push button
for WPS instead. Use the tl_mr3420v2_gpio_keys array to reflect that,
- rename kernel patch]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39063
That function provides a slightly improved sanity check than the
currently used solution.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38967
This patch enables the convenient sysupgrade feature for
WD's Wi-Fi Range Extender.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Patchwork: http://patchwork.openwrt.org/patch/4341/
[juhosg:
- rename 'mynet_rext_check_image' function to 'cybertan_check_image'
and move that into platform.sh,
- remove the the model specific 'platform_do_upgrade_mynet_rext' function,
- drop the mynet-rext.sh script,
- remove the image/Makefile change,
- update commit message]
[christian:
- check all 8 bytes of the firmware/device magic]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38966
Make the Image/Build/CyberTAN macro more generic,
and use simple wrappers for the GZIP/LZMA variants.
This simplifies the Makefile a bit, and allows to
build sysupgrade images for the devices which are
using LZMA compressed uImages.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38965
In the current sysupgrade images, the CRC32 value of
the TRX header covers the whole rootfs data. Due to
this, the CRC value should be changed during sysupgrade
otherwise the bootloader refuses to load the image on
the next boot.
Change the image generation to create sysupgrade images
where the CRC32 value covers the kernel data only. This
allows to skip the 'fixtrx' step during sysupgrade on
the target.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38964
- partitions on factory fw are a bit strange
- unknown contained some strings in factory
- unknown2 contains some atheros (2nd art ?)
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
Patchwork: http://patchwork.openwrt.org/patch/4149/
[juhosg: edit commit message]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38954
There was no way to determine a working config, because
the switch (ar8337) was not working previously.
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
Patchwork: http://patchwork.openwrt.org/patch/4470/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38953
The device has three extra LEDs which indicate the quality
of the wireless link. Thanks to rssileds, this feature now
works out of the box.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Patchwork: http://patchwork.openwrt.org/patch/4462/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38950
This patch improves support for the device considerably.
1. The wifi didn't work in the initial release. This was because
the WMAC of the AR9340 is not connected to the antennas.
(However, it can pick up wifi signals, if they are strong enough!)
Instead there's a dedicated AR9300 chip on the same board, which
works.
2. Ethernet throughput is improved. iperf shows that the hardware
can sustain more than 200Mbit/s and no longer drops any packages
when the link is under load.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Patchwork: http://patchwork.openwrt.org/patch/4461/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38949
The F1E Phy (AR8035?) requires additional bits to be
set in order to provide a fast and reliable connection
over gigabit links.
When enabled, the link doesn't suffer anymore from a small
package loss under load and the performance is improved
quite a bit as well. (203 mbit/s vs 112 mbit/s, iperf tcp).
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Patchwork: http://patchwork.openwrt.org/patch/4460/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38948
Small update to uci_defaults/01_leds, to support the usb led
Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/4426/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38947
Just a small oversight my part, added the support for the USB led
Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/4425/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38946
Patch to add the profile for the TP-LINK WR842N/ND v2
Small update, because of a change in the Makefile.
Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/4382/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38815
