Cell C RTL30VW is a LTE router with tho gigabit ethernets and integrated
QMI mPCIE modem.
This is stripped version of ASKEY RTL0030VW.
Hardware:
Specification:
-CPU: IPQ4019
-RAM: 256MB
-Flash: NAND 128MB + NOR 16MB
-WiFi: Integrated bgn/ac
-LTE: mPCIe card (Modem chipset MDM9230)
-LAN: 2 Gigabit Ports
-USB: 2x USB2.0
-Serial console: RJ-45 115200 8n1
-Unsupported VoIP
Known issues:
None so far.
Instruction install:
There are two methods: Factory web-gui and serial + tftp.
Web-gui:
1. Apply factory image via stock web-gui.
Serial + initramfs:
1. Rename OpenWrt initramfs image to "image"
2. Connect serial console (115200,8n1)
3. Set IP to different than 192.168.1.11, but 24 bit mask, eg. 192.168.1.4.
4. U-Boot commands:
sf probe && sf read 0x80000000 0x180000 0x10000
setenv serverip 192.168.1.4
set fdt_high 0x85000000
tftpboot 0x84000000 image
bootm 0x84000000
5. Install sysupgrade image via "sysupgrade -n"
Back to stock:
All is needed is swap 0x4c byte in mtd8 from 0 to 1 or 1 to 0,
do firstboot and factory reset with OFW:
1. read mtd8:
dd if=/dev/mtd8 of=/tmp/mtd8
2. go to tmp:
cd /tmp/
3. write first part of partition:
dd if=mtd8 of=mtd8.new bs=1 count=76
4. check which layout uses bootloader:
cat /proc/mtd
5a. If first are kernel_1 and rootfs_1 write 0:
echo -n -e '\x00' >> mtd8.new
5b. If first are kernel and rootfs write 1:
echo -n -e '\x01' >> mtd8.new
6. fill with rest of data:
dd if=mtd8 bs=1 skip=77 >> mtd8.new
7. CHECK IF mtd8.new HAVE CHANGED ONLY ONE BYTE! e.g with:
hexdump mtd8.new
8. write new mtd8 to flash:
mtd write mtd8.new /dev/mtd8
9. do firstboot
10.reboot
11. Do back to factory defaults in OFW GUI.
Based on work: Cezary Jackiewicz <cezary@eko.one.pl>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
MobiPromo CM520-79F is an AC1300 dual band router based on IPQ4019
Specification:
SoC/Wireless: QCA IPQ4019
RAM: 512MiB
Flash: 128MiB SLC NAND
Ethernet PHY: QCA8075
Ethernet ports: 1x WAN, 2x LAN
LEDs: 7 LEDs
2 (USB, CAN) are GPIO
other 5 (2.4G, 5G, LAN1, LAN2, WAN) are connected to a shift register
Button: Reset
Flash instruction:
Disassemble the router, connect UART pins like this:
GND TX RX
[x x . . x .]
[. . . . . .]
(QCA8075 and IPQ4019 below)
Baud-rate: 115200
Set up TFTP server: IP 192.168.1.188/24
Power on the router and interrupt the booting with UART console
env backup (in case you want to go back to stock and need it there):
printenv
(Copy the output to somewhere save)
Set bootenv:
setenv set_ubi 'set mtdids nand0=nand0; set mtdparts mtdparts=nand0:0x7480000@0xb80000(fs); ubi part fs'
setenv bootkernel 'ubi read 0x84000000 kernel; bootm 0x84000000#config@1'
setenv cm520_boot 'run set_ubi; run bootkernel'
setenv bootcmd 'run cm520_boot'
setenv bootargs
saveenv
Boot initramfs from TFTP:
tftpboot openwrt-ipq40xx-generic-mobipromo_cm520-79f-initramfs-fit-zImage.itb
bootm
After initramfs image is booted, backup rootfs partition in case of reverting to stock image
cat /dev/mtd12 > /tmp/mtd12.bin
Then fetch it via SCP
Upload nand-factory.ubi to /tmp via SCP, then run
mtd erase rootfs
mtd write /tmp/*nand-factory.ubi rootfs
reboot
To revert to stock image, restore default bootenv in uboot UART console
setenv bootcmd 'bootipq'
printenv
use the saved dump you did back when you installed OpenWrt to verify that
there are no other differences from back in the day.
saveenv
upload the backed up mtd12.bin and run
tftpboot mtd12.bin
nand erase 0xb80000 0x7480000
nand write 0x84000000 0xb80000 0x7480000
The BOOTCONFIG may have been configured to boot from alternate partition (rootfs_1) instead
In case of this, set it back to rootfs:
cd /tmp
cat /dev/mtd7 > mtd7.bin
echo -ne '\x0b' | dd of=mtd7.bin conv=notrunc bs=1 count=1 seek=4
for i in 28 48 68 108; do
dd if=/dev/zero of=mtd7.bin conv=notrunc bs=1 count=1 seek=$i
done
mtd write mtd7.bin BOOTCONFIG
mtd write mtd7.bin BOOTCONFIG1
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
[renamed volume to ubi to support autoboot,
as per David Lam's test in PR#2432]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
With the "real HZ" debate out of the way, let's actually
use the apm821xx's default upstream config file at
arch/powerpc/configs/44x/bluestone_defconfig. From what
I can tell, it sets NO_HZ (well, this platform was for
NAS, so this is a bit unexpected) and remove any specific
HZ_$VALUE symbol.
Sadly, Daniel Engberg didn't run any before/after netperf
tests, because it would have been such a slam dunk across
the boards. In case of the apm821xx the tcp tx/rx
performance improved ~14% (from 600Mbps to 700Mps).
This now causes the emac to drop frames too, so let's see
if this is causes more problems or not.
This patch includes a refresh of the configuration too.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
"Whoop whoop, sound of da police"
Add an ingress capable traffic policer module configurable with tc.
From the man page:
The police action allows to limit bandwidth of traffic matched by the
filter it is attached to. Basically there are two different algorithms
available to measure the packet rate: The first one uses an internal
dual token bucket and is configured using the rate, burst, mtu,
peakrate, overhead and linklayer parameters. The second one uses an
in-kernel sampling mechanism. It can be fine-tuned using the estimator
filter parameter.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
dcf3e63a35 added a newer kconfig version which produces a bit more local
code output, add that output to the ignore list
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
macos doesn't define a loff_t type, the native off_t type being 64bit
anyway.
Persuade e2fsprogs to accept off_t instead on macos
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
This patch adds missed line in 01_leds and fix error:
"/bin/board_detect: /etc/board.d/01_leds: line 93:
syntax error: unexpected ")" (expecting ";;")"
Fixes: c948a47 ("ramips: add support for D-Link DWR-960")
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Update xz to 5.2.5
Disable NLS support to be consistent with other tools such as bison, e2fsprogs
and sed.
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Update findutils to 4.7.0
Remove patches
Enable pthreads
Disable NLS support to be consistent with other tools such as bison, e2fsprogs
and sed.
Disable selinux support to be consistent with other tools such as sed and tar
Disable rpath as we don't need hardcoded paths
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
2188d81 jail: add support for launching extroot containers
6f3dbd2 jail: add support for userns and cgroupsns
28a06e5 jail: add support for (ram-)overlayfs
Add handling for extroot, overlaydir and tmpoverlaysize as well as
jail flags for userns and cgroupsns to OpenWrt's shell script to
allow their use in init scripts.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Some system not have mkisofs, but have genisoimage or
xorrisofs. They have compatable options for mkisofs,
so let them as alternatives to mkisofs.
Signed-off-by: 李国 <uxgood.org@gmail.com>
grub-bios-setup requires two images (boot.img and core.img),
but they are missing. This make an error during sysupgrade:
Upgrading bootloader on /dev/sda...
grub-bios-setup: error: cannot open `/tmp/boot/boot/grub/boot.img': No
such file or directory.
Signed-off-by: 李国 <uxgood.org@gmail.com>
This symbol had been enabled in the initial device support submission
for kernel 4.14, but apparently got lost during the v4.19 port.
The ASUS Lyra MAP-AC2200 has a single (very bright) rgb LED, which is
controlled by the TI/National LP5523/55231 LED driver chip. It is left
enabled in a pulsating infinite rainbow loop by the bootloader,
expecting it to be reconfigured (disabled by default) after the boot
process has finished and is also required to indicate failsafe/
firstboot conditions.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
This addes the option to treat recursive dependencies as warnings
instead of errors, by running make with WARN_RECURSIVE_DEP=1.
Note that the script/config targets will not get rebuilt when you add or
remove WARN_RECURSIVE_DEP while running make. One must run
'make config-clean' before building config with a different setting.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Major changes include:
- Much more readable reverse dependencies separated in groups
- Improved recursive dependency report
- More readable .config files: add comments to signal end of menus
- More warnings for incorrect Config.in entries, such as a 'choice'
default not contained in the 'choice'
- Hability to properly display pseudographics with non-latin locales
- Recursive dependencies are now treated as errors - this should make
it harder for them to creep in.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Instead of passing pkg-config location through a variable when building
qconf (make xconfig), prepend its parent directory to the PATH, as it is
being done for other conf targets.
Use a Makefile pattern rule to group all 'scripts/config/%onf'
(currently conf, mconf, qconf) targets in a single rule. Add -O2 to
CFLAGS when building them as well.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Currently, RTC_SUPPORT is defined as a tristate, with 'depends on m',
which is supposed to only let it be set to 'm' or 'n'. However,
scripts/target-metadata.pl will 'select' it, or setting it to 'y', which
defeats it's 'depends on m' restriction. The users of the symbol are
not expecting it to be necessarily 'm' either, so we can safely use it
as bool.
Newer versions of Linux 'conf' will issue a warning when it detects such
unmet dependencies, and will set it to 'n' instead of 'y', as the
current version does. In all cases, 'm' is never used.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Newer versions of the kconfig program requires quoting the arguments of
the 'source' directive. These are the last ones not using them.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
IPv6 modules should all depend on @IPV6, to avoid circular dependencies
problems, especially if they select a module that depends on IPV6 as
well. In theory, if a package A depends on IPV6, any package doing
'select A' (DEPENDS+= A) should also depend on IPV6; otherwise selecting
A will fail. Sometimes the build system is forgiving this, but
eventually, and unexpectedly, it may blow up on some other commit.
Alternatively one can conditionally add IPv6 dependencies only if
CONFIG_IPV6 is selected: (DEPENDS+= +IPV6:package6).
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
The symvers files of older kernel versions are incompatible with the ones
from 5.4, so changing the kernel version without running make clean was
causing build failures in kernel module packages.
Fix this by moving the directory, ensuring that symvers files get thrown
away with a kernel version change
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Specifications:
- Qualcomm QCA9531 + QCA9886
- dual band, antenna 2*3dBi
- Output power 50mW (17dBm)
- 1x 10/100 Mbps LAN RJ45
- 128 MB RAM / 16 MB FLASH (w25q128)
- 3 LEDs (red/green/blue)
incorporated in
"color wheel reset switch"
- UART 115200 8N1
Flashing instructions:
The U-boot bootloader contains a recovery HTTP server
to upload the firmware. Push the reset button while powering the
device on and keep it pressed for ~10 seconds. The device's LEDs will
blink several times and the recovery page will be at
http://192.168.1.1; use it to upload the sysupgrade image.
Alternatively, the original firmware is based on OpenWrt so a
sysupgrade image can be installed via the stock web GUI. Settings from
the original firmware will be saved and restored on the new one, so a
factory reset will be needed. To do so, once the new firmware is flashed,
enter into failsafe mode by pressing the reset button several times during
the boot process, until it starts flashing. Once in failsafe mode, perform
a factory reset as usual.
LED-Info:
The LEDs on the Comfast stock fw have a very proprietary behaviour,
corresponding to the user selected working mode (AP, ROUTER or REPEATER).
In the first two cases, only blue is used for status and LAN signaling. When
using the latter, blue is always off (except for sysupgrade), either red
signals bad rssi on master-link, or green good. Since the default working
mode of OpenWrt resembles that of a router/AP, the default behavior is
implemented accordingly.
MAC addresses (art partition):
location address (example) use in vendor firmware
0x0 xx:xx:xx:xx:xc:f8 -> eth0
0x6 xx:xx:xx:xx:xc:fa -> wlan5g (+2)
0x1002 xx:xx:xx:xx:xc:f9 -> not used
0x5006 xx:xx:xx:xx:xc:fb -> not used
--- xx:xx:xx:xx:xd:02 -> wlan2g (+10)
The same strange situation has already been observed and documented
for COMFAST CF-E560AC.
Signed-off-by: Roman Hampel <rhamp@arcor.de>
Co-developed-by: Joao Albuquerque <joaohccalbu@gmail.com>
Signed-off-by: Joao Albuquerque <joaohccalbu@gmail.com>
[adjust and extend commit message, rebase, minor DTS adjustments,
add correct MAC address for wmac, change RSSI LED names and behavior]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Fixing a build error when CONFIG_KERNEL_KEXEC is enabled:
make[5]: Entering directory '/home/bjorn/tmp/tmp-lede/build_dir/target-mipsel_24kc_musl/linux-ramips_mt7621/linux-5.4.28'
CALL scripts/checksyscalls.sh
CALL scripts/atomic/check-atomics.sh
CHK include/generated/compile.h
CC arch/mips/kernel/machine_kexec.o
arch/mips/kernel/machine_kexec.c: In function 'kexec_nonboot_cpu_jump':
arch/mips/kernel/machine_kexec.c:268:27: error: 'relocate_new_kernel_size' undeclared (first use in this function); did you mean 'kexec_relocate_new_kernel_end'?
reboot_code_buffer + relocate_new_kernel_size);
^~~~~~~~~~~~~~~~~~~~~~~~
kexec_relocate_new_kernel_end
arch/mips/kernel/machine_kexec.c:268:27: note: each undeclared identifier is reported only once for each function it appears in
arch/mips/kernel/machine_kexec.c: In function 'kexec_reboot':
arch/mips/kernel/machine_kexec.c:306:27: error: 'relocate_new_kernel_size' undeclared (first use in this function); did you mean 'kexec_relocate_new_kernel_end'?
reboot_code_buffer + relocate_new_kernel_size);
^~~~~~~~~~~~~~~~~~~~~~~~
kexec_relocate_new_kernel_end
make[7]: *** [scripts/Makefile.build:266: arch/mips/kernel/machine_kexec.o] Error 1
Signed-off-by: Bjørn Mork <bjorn@mork.no>
The NAS packages for Gemini doesn't even include the
block-mount package. Augment the list to be based off
the DEFAULT_PACKAGES.nas to make sure we extend on the
essentials.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since linux kernel commit 0768e17073dc527ccd18ed5f96ce85f9985e9115
(2019-04-19) the asm-generic/sockios.h header no longer defines
SIOCGSTAMP. Instead it provides only SIOCGSTAMP_OLD.
The linux/sockios.h header now defines SIOCGSTAMP using either
SIOCGSTAMP_OLD or SIOCGSTAMP_NEW as appropriate. This linux only
header file is not included so we get a build failure.
Signed-off-by: Norbert van Bolhuis <nvbolhuis@aimvalley.nl>
ipq806x has been tested for a lot and lots of people reported good results.
Switch the main kernel to 5.4 following the other targets.
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [ipq8065, NBG6817]
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
ZyXEL Keenetic has 8MB flash, but OpenWrt uses only 4MB.
This commit fixes the problem.
WikiDevi page [1] says that ZyXEL Keenetic has FLA1: 8 MiB, there is
an article with specs [2] (in Russian).
[1] https://wikidevi.wi-cat.ru/ZyXEL_Keenetic
[2] https://3dnews.ru/608774/page-2.html
Fixes: FS#2487
Fixes: a7cbf59e0e ("ramips: add new device ZyXEL Keenetic as kn")
Signed-off-by: Alexey Dobrovolsky <dobrovolskiy.alexey@gmail.com>
MAC addresses of the ethernet devices (eth0 & eth1) are randomly set at
boot time by the ag71xx driver, because it is currently not possible to
retrieve MAC addresses in ASCII format within the DTS file.
This commit works around this behaviour by setting the MAC addresses
during the preinit phase.
The same has been implemented recently for the Siemens WS-AP3610 in
d2b8ccb1c0 ("ath79: add support for Siemens WS-AP3610").
MAC assignment in vendor firmware is as follows:
use vendor address OpenWrt
2g wifi0 ethaddr -> wlan1
5g wifi1 ethaddr +1 -> wlan0
lan eth1 ethaddr +2 -> eth0
wan eth0 ethaddr +3 -> eth1
ethaddr is retrieved by $(mtd_get_mac_ascii u-boot-env ethaddr)
Note that both Wifi and ethernet indexing is swapped in OpenWrt
compared to vendor firmware.
Suggested-by: Guillaume Lefebvre <guillaume@zelig.ch>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Kevin Gagnon <kevin_gagnon@videotron.ca>
This commit add patch with 14c3:7610 pci id addition.
It was sent upstream.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
[bumped PKG_RELEASE]
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
At this moment mt7620 ethernet driver doesn't support rgmii delays
configuration. SoC MT7620 have bits 2 and 3 in GPC1 an GPC2 to configure
delays for rx and tx rgmii interface.
This patch adds rx/tx rgmii delay configuration from dts.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Backport patches which adds suport for the Wistron Neweb D19Q1 3G/4G modem,
used in D-Link DWR-960.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
So far, image/device/board names for Mikrotik devices in mt7621 have
been used quite inconsistently.
This patch harmonizes the naming scheme by applying the same style
as used lately in ath79, i.e. using "RouterBOARD" as separate word
in the model name (instead of RB prefix for the number) and deriving
the board/device name from that (= make lower case and replace spaces
by hyphens).
This style has already been used for most the model/DEVICE_MODEL
variables in mt7621, so this is essentially just adjusting the remaining
variables to that.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Allows proper usage of the ss tool. Otherwise, several errors and bad
data gets thrown:
Cannot open netlink socket: Protocol not supported
Cannot open netlink socket: Protocol not supported
Cannot open netlink socket: Protocol not supported
Cannot open netlink socket: Protocol not supported
Cannot open netlink socket: Protocol not supported
Cannot open netlink socket: Protocol not supported
Cannot open netlink socket: Protocol not supported
Originally reported here: https://github.com/openwrt/packages/issues/8232
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Buffalo WSR-2533DHPL is a 2.4/5 GHz band 11ac router, based on MediaTek
MT7621A.
Specification:
- SoC : MediaTek MT7621A
- RAM : DDR3 128 MiB
- Flash : SPI-NOR 16 MiB
- WLAN : 2.4/5 GHz 4T4R (2x MediaTek MT7615N)
- Ethernet : 10/100/1000 Mbps
- Switch : MediaTek MT7530 (SoC)
- LED/keys : 8x/6x (3x buttons, 2x slide-switches)
- UART : through-hole on PCB
- J4: 3.3V, GND, TX, RX from triangle-mark
- 57600n8
- Power : 12VDC 1.5A
Flash instruction using initramfs image:
1. prepare the TFTP server with the initramfs image renamed to
"linux.trx-recovery" and IP address "192.168.11.2"
2. press the "AOSS" button while powering on the WSR-2533DHPL
3. after 10 seconds, release the "AOSS" button, WSR-2533DHPL downloads
the initramfs image and boot with it automatically
4. on the initramfs image, download the sysupgrade image to the device
and perform sysupgrade with it
5. wait ~120 seconds to complete flashing
Switch position overview:
- slide-switch1 (2x positions)
- "AUTO"
- "MANUAL" (not connected to gpio)
- slide-switch2 (3x positions)
- "ROUTER"
- "AP" (not connected to gpio)
- "WB"
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[add note on switches, fix group->groups for state_default]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This prepares support for models XAP-1610 and XWR-3150. Flashing
requires using Luxul firmware version:
1) 8.1.0 or newer for XAP-1610
2) 6.4.0 or newer for XWR-3150
and uploading firmware using "Firmware Update" web UI page.
Signed-off-by: Dan Haab <dan.haab@legrand.com>
Specifications:
Qualcomm/Atheros QCA9531 + QCA9886
2x 10/100 Mbps Ethernet, with 48v PoE
2T2R 2.4 GHz, 802.11b/g/n
2T2R 5 GHz, 802.11a/n/ac
128MB RAM
16MB SPI Flash
4x LED (Always On Power, LAN, WAN, WLAN)
Flashing Instructions:
Original firmware is based on OpenWRT, so flashing the sysupgrade image on
the factory firmware is sufficient.
Tested: Reset button, WAN LED, LAN LED, Power LED (always on, not much
to test), WLAN LED (one LED only for 2 interfaces, by default it gets
assigned to the first interface), MAC addresses (match factory firmware).
My LAN factory MAC address ends in F2.
use stock_mac art_loc
lan :f2 0x0
wan :f3 0x1002
5g :f4 0x6
2g :f5 0x5006
Since MAC address flash locations do not really match their use in vendor
firmware (e.g. address from 5 GHz calibration data is assigned to 2.4 GHz
WiFi), just calculate the MAC addresses with an offset based on 0x0 address.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
[add MAC address comment]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Use upstream latest git HEAD as it allows to remove the patches
700-radius-Prevent-buffer-overflow-in-rc_mksid,
701-pppd-Fix-bounds-check-in-EAP-code and
702-pppd-Ignore-received-EAP-messages-when-not-doing-EAP and
take in other fixes.
41a7323 pppd: Fixed spelling 'unkown' => 'unknown' (#141)
6b014be pppd: Print version information to stdout instead of stderr (#133)
cba2736 pppd: Add RFC1990 (Multilink) to the See Also section of the man page
f2f9554 pppd: Add mppe.h to the list of headers to install if MPPE is defined
ae54fcf pppd: Obfuscate password argument string
8d45443 pppd: Ignore received EAP messages when not doing EAP
8d7970b pppd: Fix bounds check in EAP code
858976b radius: Prevent buffer overflow in rc_mksid()
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Remove libressl patches; they are no longer needed as LibreSSl adde
support
Replace qt tests patch with one that disables all of them.
Refresh remaining one.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
This changes the node names for the LEDs in the Netgear R6120
device-tree file to provide consistency with other devices.
Signed-off-by: Alex Lewontin <alex.c.lewontin@gmail.com>
[improve commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
