Commit Graph

159 Commits

Author SHA1 Message Date
Leon M. George
a0bb356612 ath79: add support for Compex WPJ344
Specifications:

SoC: AR9344
DRAM: 128MB DDR2
Flash: 16MB SPI-NOR
2 Gigabit ethernet ports
2×2 2.4GHz on-board radio
miniPCIe slot that supports 5GHz radio
PoE 48V IEEE 802.3af/at - 24V passive optional
USB 2.0 header

Installation:

To install, either start tftp in bin/targets/ath79/generic/ and use
the u-boot prompt over UART:

tftpboot 0x80500000 openwrt-ath79-generic-compex_wpj344-16m-squashfs-sysupgrade.bin
erase 0x9f030000 +$filesize
erase 0x9f680000 +1
cp.b $fileaddr 0x9f030000 $filesize
boot

The cpximg file can be used with sysupgrade in the stock firmware (add
SSH key in luci for root access) or with the built-in cpximg loader.
The cpximg loader can be started either by holding the reset button
during power up or by entering the u-boot prompt and entering 'cpximg'.
Once it's running, a TFTP-server under 192.168.1.1 will accept the image
appropriate for the board revision that is etched on the board.

For example, if the board is labelled '6A08':

tftp -v -m binary 192.168.1.1 -c put openwrt-ath79-generic-compex_wpj344-16m-squashfs-cpximg-6a08.bin

MAC addresses:

<&uboot 0x2e010>  *:99  (label)
<&uboot 0x2e018>  *:9a
<&uboot 0x2e020>  *:9b
<&uboot 0x2e028>  *:9c

Only the first two are used (for ethernet), the WiFi modules have
separate (valid) addresses. The latter two addresses are not used.

Signed-off-by: Leon M. George <leon@georgemail.eu>
[minor commit message adjustments, drop gpio in DTS, DTS style fixes,
sorting, drop unused cpximg recipe]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-03 17:37:02 +02:00
Leon M. George
9f261e36de ath79: build Compex WPJ531 cpximg files
Generate additional images that are compatible to the cpximg loader.
The cpximg loader can be started either by holding the reset button during
power up or by entering the u-boot prompt and entering 'cpximg'.
Once it's running, a TFTP-server under 192.168.1.1 will accept the image
appropriate for the board revision that is etched on the board.

For example, if the board is labelled '7A04':

tftp -v -m binary 192.168.1.1 -c put openwrt-ath79-generic-compex_wpj531-16m-squashfs-cpximg-7A04.bin

These files can also be used with the sysupgrade utility in stock images (add
SSH key in luci for root access).

Signed-off-by: Leon M. George <leon@georgemail.eu>
[fix sorting of definitions]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-28 00:26:39 +02:00
Leon M. George
e10dd48360 ath79: add support for Compex WPJ531 (16M)
Specifications:

SoC: QCA9531
DRAM: 128MB DDR2
Flash: 16MB SPI-NOR
2 100MBit ethernet ports
2×2 2.4GHz on-board radio
miniPCIe slot that supports 5GHz radio
PoE 24V - 48V IEEE 802.3af optional
USB 2.0 header

Installation:

To install, start a tftp server in bin/targets/ath79/generic/ and use the
u-boot prompt over UART:

tftpboot 0x80500000 openwrt-ath79-generic-compex_wpj531-16m-squashfs-sysupgrade.bin
erase 0x9f030000 +$filesize
erase 0x9f680000 +1
cp.b $fileaddr 0x9f030000 $filesize
boot

The cpximg file can be used with sysupgrade in the stock firmware (add SSH key
in luci for root access).

Another way is to hold the reset button during power up or running 'cpximg' in
the u-boot prompt.
Once the last LED starts flashing regularly, a TFTP-server under 192.168.1.1
will accept the image appropriate for the board revision that is etched on the
board.

For example, if the board is labelled '7A04':

tftp -v -m binary 192.168.1.1 -c put openwrt-ath79-generic-compex_wpj531-16m-squashfs-cpximg-7A04.bin

MAC addresses:

<&uboot 0x2e010>  *:cb  (label)
<&uboot 0x2e018>  *:cc
<&uboot 0x2e020>  *:cd
<&uboot 0x2e028>  *:ce

Only the first two are used (for ethernet), the WiFi modules have
separate (valid) addresses. The latter two addresses are not used.

Signed-off-by: Leon M. George <leon@georgemail.eu>
[commit title/message facelift, fix rssileds, add led aliases]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-28 00:26:39 +02:00
Natalie Kagelmacher
8ff631feff ath79: add support for AVM FRITZ!WLAN Repeater DVB-C
This commit adds support for the AVM FRITZ!WLAN Repeater DVB-C

SOC:   Qualcomm Atheros QCA9556
RAM:   64 MiB
FLASH: 16 MB SPI-NOR
WLAN:  QCA9556 3T3R 2.4 GHZ b/g/n and
       QCA9880 3T3R 5 GHz n/ac
ETH:   Atheros AR8033 1000 Base-T
DVB-C: EM28174 with MaxLinear MXL251 tuner
BTN:   WPS Button
LED:   Power, WLAN, TV, RSSI0-4

Tested and working:
 - Ethernet (correct MAC, gigabit, iperf3 about 200 Mbit/s)
 - 2.4 GHz Wi-Fi (correct MAC)
 - 5 GHz Wi-Fi (correct MAC)
 - WPS Button (tested using wifitoggle)
 - LEDs
 - Installation via EVA bootloader (FTP recovery)
 - OpenWrt sysupgrade (both CLI and LuCI)
 - Download of "urlader" (mtd0)

Not working:
 - Internal USB
 - DVB-C em28174+MxL251 (depends on internal USB)

Installation via EVA bootloader (FTP recovery):
Set NIC to 192.168.178.3/24 gateway 192.168.178.1 and power on the device,
connect to 192.168.178.1 through FTP and sign in with adam2/adam2:

ftp> quote USER adam2
ftp> quote PASS adam2
ftp> binary
ftp> debug
ftp> passive
ftp> quote MEDIA FLSH
ftp> put openwrt-sysupgrade.bin mtd1

Wait for "Transfer complete" together with the transfer details.
Wait two minutes to make sure flash is complete (just to be safe).

Then restart the device (power off and on) to boot into OpenWrt.
Revert your NIC settings to reach OpenWrt at 192.168.1.1

Signed-off-by: Natalie Kagelmacher <nataliek@pm.me>
[fixed sorting - removed change to other board -
prettified commit message]
Signed-off-by: David Bauer <mail@david-bauer.net>
2020-06-25 02:35:35 +02:00
Stijn Tintel
cd09f26660 ath79: add support for D-Link DAP-2695-A1
Hardware:
* SoC: Qualcomm Atheros QCA9558
* RAM: 256MB
* Flash: 16MB SPI NOR
* Ethernet: 2x 10/100/1000 (1x 802.3at PoE-PD)
* WiFi 2.4GHz: Qualcomm Atheros QCA9558
* WiFi 5GHz: Qualcomm Ahteros QCA9880-2R4E
* LEDS: 1x 5GHz, 1x 2.4GHz, 1x LAN1(POE), 1x LAN2, 1x POWER
* Buttons: 1x RESET
* UART: 1x RJ45 RS-232 Console port

Installation via stock firmware:
* Install the factory image via the stock firmware web interface

Installation via bootloader Emergency Web Server:
* Connect your PC to the LAN1(PoE) port
* Configure your PC with IP address 192.168.0.90
* Open a serial console to the Console port (115200,8n1)
* Press "q" within 2s when "press 'q' to stop autoboot" appears
* Open http://192.168.0.50 in a browser
* Upload either the factory or the sysupgrade image
* Once you see "write image into flash...OK,dest addr=0x9f070000" you
  can power-cycle the device. Ignore "checksum bad" messages.

Setting the MAC addresses for the ethernet interfaces via
/etc/board.d/02_network adds the following snippets to
/etc/config/network:

config device 'lan_eth0_1_dev'
        option name 'eth0.1'
        option macaddr 'xx:xx:xx:xx:xx:xx'

config device 'wan_eth1_2_dev'
        option name 'eth1.2'
        option macaddr 'xx:xx:xx:xx:xx:xx'

This would result in the proper MAC addresses being set for the VLAN
subinterfaces, but the parent interfaces would still have a random MAC
address. Using untagged VLANs could solve this, but would still leave
those extra snippets in /etc/config/network, and then the device VLAN
setup would differ from the one used in ar71xx. Therefore, the MAC
addresses of the ethernet interfaces are being set via preinit instead.

The bdcfg partition contains 4 MAC address labels:
 - lanmac
 - wanmac
 - wlanmac
 - wlanmac_a

The first 3 all contain the same MAC address, which is also the one on
the label.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Reviewed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-11 19:44:45 +03:00
Renaud Lepage
108df3eabb ath79: add support for the Netgear WNDRMAC v1
The Netgear WNDRMAC v1 is a hardware variant of the Netgear WNDR3700 v2

Specifications
==============
* SoC: Atheros AR7161
* RAM: 64mb
* Flash on board: 16mb
* WiFi: Atheros AR9220 (a/n), Atheros AR9223 (b/g/n)
* Ethernet: RealTek RTL8366SR (1xWAN, 4xLAN, Gigabit)
* Power: 12 VDC, 2.5 A
* Full specs on [openwrt.org](https://openwrt.org/toh/hwdata/netgear/netgear_wndrmac_v1)

Flash Instructions
==================
It is possible to use the OEM Upgrade page to install the `factory`
variant of the firmware.

After the initial upgrade, you will need to telnet into the router
(default IP 192.168.1.1) to install anything. You may install LuCI
this way. At this point, you will have a web interface to configure
OpenWRT on the WNDRMAC v1.

Please use the `sysupgrade` variant for subsequent flashes.

Recovery Instructions
=====================
A TFTP-based recovery flash is possible if the need arises. Please refer
to the WNDR3700 page on openwrt.org for details.

https://openwrt.org/toh/netgear/wndr3700#troubleshooting_and_recovery

Signed-off-by: Renaud Lepage <root@cybikbase.com>
[update DTSI include name]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-11 01:44:13 +02:00
Renaud Lepage
7f297e740b ath79: add support for the Netgear WNDRMAC v2
The Netgear WNDRMAC v2 is a hardware variant of the Netgear WNDR3800

Specifications
==============
* SoC: Atheros AR7161
* RAM: 128mb
* Flash on board: 16mb
* WiFi: Atheros AR9220 (a/n), Atheros AR9223 (b/g/n)
* Ethernet: RealTek RTL8366SR (1xWAN, 4xLAN, Gigabit)
* Serial console: Yes, 115200 / 8N1 (JTAG)
* USB: 1x2.0
* Power: 12 VDC, 2.5 A
* Full specs on [openwrt.org](https://openwrt.org/toh/hwdata/netgear/netgear_wndrmac_v2)

Flash Instructions
==================
It is possible to use the OEM Upgrade page to install the `factory`
variant of the firmware.

After the initial upgrade, you will need to telnet into the router
(default IP 192.168.1.1) to install anything. You may install LuCI
this way. At this point, you will have a web interface to configure
OpenWRT on the WNDRMAC v2.

Please use the `sysupgrade` variant for subsequent flashes.

Recovery Instructions
=====================
A TFTP-based recovery flash is possible if the need arises. Please refer
to the WNDR3800 page on openwrt.org for details.

https://openwrt.org/toh/netgear/wndr3800#recovery_flash_in_failsafe_mode

Signed-off-by: Renaud Lepage <root@cybikbase.com>
[do not add device to uboot-envtools, update DTSI name]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-11 01:44:13 +02:00
Pavel Balan
ad84c09502 ath79: add support for COMFAST CF-E130N v2
This patch adds support for the COMFAST CF-E130N v2, an outdoor wireless
CPE with a single Ethernet port and a 802.11bgn radio.

Specifications:

 - QCA9531 SoC
 - 1x 10/100 Mbps Ethernet with PoE-in support
 - 64 MB of RAM (DDR2)
 - 16 MB of FLASH
 - 5 dBi built-in antenna
 - POWER/LAN/WLAN green LEDs
 - 4x RSSI LEDs (2x red, 2x green)
 - UART (115200 8N1) and GPIO (J9) headers on PCB

Flashing instructions:

 The original firmware is based on OpenWrt so a sysupgrade image can be
 installed via the stock web GUI.

 The U-boot bootloader also contains a backup TFTP client to upload the
 firmware from. Upon boot, it checks its ethernet network for the IP
 192.168.1.10. Host a TFTP server and provide the image to be flashed as
 file firmware_auto.bin.

MAC address setup:

The art partition contains four consecutive MAC addresses:

0x0    aa:bb:cc:xx:xx:c4
0x6    aa:bb:cc:xx:xx:c6
0x1002 aa:bb:cc:xx:xx:c5
0x5006 aa:bb:cc:xx:xx:c7

However, the manufacturer in its infinite wisdom decided that one address
is enough and both eth0 and WiFi get the MAC address from 0x0 (yes, that's
overwriting the existing and valid address in 0x1002). This is obviously
also the address on the device's label.

Signed-off-by: Pavel Balan <admin@kryma.net>
[fix configs partition, fix IMAGE_SIZE, add MAC address comment, rename
ATH_SOC to SOC]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-28 01:47:54 +02:00
David Bauer
ebddc5f984 ath79: add support for Enterasys WS-AP3705i
Hardware
--------
SoC:    Atheros AR9344
RAM:    128M DDR2
FLASH:  2x Macronix MX25L12845EM
        2x 16MiB SPI-NOR
WLAN2:  Atheros AR9344 2x2 2T2R
WLAN5:  Atheros AR9580 2x2 2T2R
SERIAL: Cisco-RJ45 on the back (115200 8n1)

Installation
------------

The U-Boot CLI is password protected (using the same credentials as the
OS). Default is admin/new2day.

1. Download the OpenWrt initramfs-image. Place it into a TFTP server
   root directory and rename it to 1401A8C0.img. Configure the TFTP
   server to listen at 192.168.1.66/24.

2. Connect the TFTP server to the access point.

3. Connect to the serial console of the access point. Attach power and
   interrupt the boot procedure when prompted (bootdelay is 1 second).

4. Configure the U-Boot environment for booting OpenWrt from Ram and
   flash:

   $ setenv boot_openwrt 'setenv bootargs; bootm 0xbf230000'
   $ setenv ramboot_openwrt 'setenv serverip 192.168.1.66;
     tftpboot 0x85000000; bootm'
   $ setenv bootcmd 'run boot_openwrt'
   $ saveenv

5. Load OpenWrt into memory:

   $ run ramboot_openwrt

   Wait for the image to boot.

6. Transfer the OpenWrt sysupgrade image to the device. Write the image
   to flash using sysupgrade:

   $ sysupgrade -n /path/to/openwrt-sysuograde.bin

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-05-22 21:54:30 +02:00
Daniel Golle
aa4a33ac62 ath79: add support for Teltonika RUT955 H7V3C0
This board was previously supported in ar71xx as 'RUT9XX'. The
difference between that and the other RUT955 board already supported in
ath79 is that instead of the SPI shift registers driving the LEDs and
digital outputs that model got an I2C GPIO expander instead.

To support LEDs during early boot and interrupt-driven digital inputs,
I2C support as well as support for PCA953x has to be built-in and
cannot be kernel modules, hence select those symbols for ath79/generic.

Specification:

- 550/400/200 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 4x 10/100 Mbps Ethernet, with passive PoE support on LAN1
- 2T2R 2,4 GHz (AR9344)
- built-in 4G/3G module (example: Quectel EC-25EU)
- internal microSD slot (spi-mmc, buggy and disabled for now)
- RS232 on D-Sub9 port (Cypress ACM via USB, /dev/ttyACM0)
- RS422/RS485 (AR934x high speed UART, /dev/ttyATH1)
- analog 0-24V input (MCP3221)
- various digital inputs and outputs incl. a relay
- 11x LED (4 are driven by AR9344, 7 by PCA9539)
- 2x miniSIM slot (can be swapped via GPIO)
- 2x RP-SMA/F (Wi-Fi), 3x SMA/F (2x WWAN, GPS)
- 1x button (reset)
- DC jack for main power input (9-30 V)
- debugging UART available on PCB edge connector

Serial console (/dev/ttyS0) pinout:

- RX: pin1 (square) on top side of the main PCB (AR9344 is on top)
- TX: pin1 (square) on bottom side

Flash instruction:

Vendor firmware is based on OpenWrt CC release. Use the "factory" image
directly in GUI (make sure to uncheck "keep settings") or in U-Boot web
based recovery. To avoid any problems, make sure to first update vendor
firmware to latest version - "factory" image was successfully tested on
device running "RUT9XX_R_00.06.051" firmware and U-Boot "3.0.1".

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2020-04-29 21:32:35 +01:00
Álvaro Fernández Rojas
2e5e9b459e ath10k-ct-firmware: rename ct-htt packages
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-04-28 09:33:09 +02:00
David Bauer
8d9c1087e4 ath79: add support for AVM FRITZ!WLAN Repeater 450E
SOC:    Qualcomm QCA9556 (Scorpion) 560MHz MIPS74Kc
RAM:    64MB Zentel A3R12E40CBF DDR2
FLASH:  16MiB Winbond W25Q128 SPI NOR
WLAN1:  QCA9556 2.4 GHz 802.11b/g/n 3x3
INPUT:  WPS button
LED:    Power, WiFi, LAN, RSSI indicator
Serial: Header Next to Black metal shield
        Pinout is 3.3V - RX - TX - GND (Square Pad is 3.3V)
        The Serial setting is 115200-8-N-1.

Installation via EVA:
In the first seconds after Power is connected, the bootloader will
listen for FTP connections on 192.168.178.1. Firmware can be uploaded
like following:

  ftp> quote USER adam2
  ftp> quote PASS adam2
  ftp> binary
  ftp> debug
  ftp> passive
  ftp> quote MEDIA FLSH
  ftp> put openwrt-sysupgrade.bin mtd1

Note that this procedure might take up to two minutes.
You need to powercycle the device afterwards to boot OpenWRT.

Tested-by: Andreas Ziegler <dev@andreas-ziegler.de>
Signed-off-by: David Bauer <mail@david-bauer.net>
2020-04-19 16:45:40 +02:00
David Bauer
edf812e25c ath79: remove stray pipe
Fixes: 8918c038f3 ("ath79: add support for AVM FRITZ!WLAN Repeater 1750E")

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-04-17 14:15:09 +02:00
David Bauer
8918c038f3 ath79: add support for AVM FRITZ!WLAN Repeater 1750E
This commit adds support for the AVM Fritz!WLAN Repeater 1750E

SOC:	Qualcomm QCA9556 (Scorpion) 720MHz MIPS74Kc
RAM:    64MB Zentel A3R12E40CBF DDR2
FLASH:  16MiB Winbond W25Q128 SPI NOR
WLAN1:  QCA9556 2.4 GHz 802.11b/g/n 3x3
WLAN2:  QCA9880 5 GHz 802.11 n/ac 3x3
INPUT:  WPS button
LED:    Power, WiFi, LAN, RSSI indicator
Serial: Header Next to Black metal shield
        Pinout is 3.3V - RX - TX - GND (Square Pad is 3.3V)
        The Serial setting is 115200-8-N-1.

Tested and working:
 - Ethernet
 - 2.4 GHz WiFi (correct MAC)
 - 5 GHz WiFi (correct MAC)
 - Installation via EVA bootloader
 - OpenWRT sysupgrade
 - Buttons
 - LEDs

Installation via EVA:
In the first seconds after Power is connected, the bootloader will
listen for FTP connections on 192.168.178.1. Firmware can be uploaded
like following:

  ftp> quote USER adam2
  ftp> quote PASS adam2
  ftp> binary
  ftp> debug
  ftp> passive
  ftp> quote MEDIA FLSH
  ftp> put openwrt-sysupgrade.bin mtd1

Note that this procedure might take up to two minutes.
You need to powercycle the Device afterwards to boot OpenWRT.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-04-17 13:27:40 +02:00
Roman Hampel
cd510e775b ath79: add support for Comfast CF-WR752AC v1
Specifications:

- Qualcomm QCA9531 + QCA9886
- dual band, antenna 2*3dBi
- Output power 50mW (17dBm)
- 1x 10/100 Mbps LAN RJ45
- 128 MB RAM / 16 MB FLASH (w25q128)
- 3 LEDs (red/green/blue)
  incorporated in
  "color wheel reset switch"
- UART 115200 8N1

Flashing instructions:

 The U-boot bootloader contains a recovery HTTP server
 to upload the  firmware. Push the reset button while powering the
 device on and keep it pressed for ~10 seconds. The device's LEDs will
 blink several times and the recovery page will be at
 http://192.168.1.1; use it to upload the sysupgrade image.

 Alternatively, the original firmware is based on OpenWrt so a
 sysupgrade image can be installed via the stock web GUI. Settings from
 the original firmware will be saved and restored on the new one, so a
 factory reset will be needed. To do so, once the new firmware is flashed,
 enter into failsafe mode by pressing the reset button several times during
 the boot process, until it starts flashing. Once in failsafe mode, perform
 a factory reset as usual.

LED-Info:

 The LEDs on the Comfast stock fw have a very proprietary behaviour,
 corresponding to the user selected working mode (AP, ROUTER or REPEATER).
 In the first two cases, only blue is used for status and LAN signaling. When
 using the latter, blue is always off (except for sysupgrade), either red
 signals bad rssi on master-link, or green good. Since the default working
 mode of OpenWrt resembles that of a router/AP, the default behavior is
 implemented accordingly.

MAC addresses (art partition):

location  address (example)    use in vendor firmware
0x0       xx:xx:xx:xx:xc:f8 -> eth0
0x6       xx:xx:xx:xx:xc:fa -> wlan5g (+2)
0x1002    xx:xx:xx:xx:xc:f9 -> not used
0x5006    xx:xx:xx:xx:xc:fb -> not used
---       xx:xx:xx:xx:xd:02 -> wlan2g (+10)

The same strange situation has already been observed and documented
for COMFAST CF-E560AC.

Signed-off-by: Roman Hampel <rhamp@arcor.de>
Co-developed-by: Joao Albuquerque <joaohccalbu@gmail.com>
Signed-off-by: Joao Albuquerque <joaohccalbu@gmail.com>
[adjust and extend commit message, rebase, minor DTS adjustments,
add correct MAC address for wmac, change RSSI LED names and behavior]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-09 01:06:37 +02:00
Chris Morgan
7daab62861 ath79: add support for Comfast CF-EW72
Specifications:
Qualcomm/Atheros QCA9531 + QCA9886
2x 10/100 Mbps Ethernet, with 48v PoE
2T2R 2.4 GHz, 802.11b/g/n
2T2R 5 GHz, 802.11a/n/ac
128MB RAM
16MB SPI Flash
4x LED (Always On Power, LAN, WAN, WLAN)

Flashing Instructions:
Original firmware is based on OpenWRT, so flashing the sysupgrade image on
the factory firmware is sufficient.

Tested: Reset button, WAN LED, LAN LED, Power LED (always on, not much
to test), WLAN LED (one LED only for 2 interfaces, by default it gets
assigned to the first interface), MAC addresses (match factory firmware).
My LAN factory MAC address ends in F2.

use	stock_mac	art_loc
lan	:f2		0x0
wan	:f3		0x1002
5g	:f4		0x6
2g	:f5		0x5006

Since MAC address flash locations do not really match their use in vendor
firmware (e.g. address from 5 GHz calibration data is assigned to 2.4 GHz
WiFi), just calculate the MAC addresses with an offset based on 0x0 address.

Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
[add MAC address comment]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-07 01:00:10 +02:00
Sungbo Eo
3f14f034fb treewide: omit IMAGE_SIZE argument from check-size
Now that check-size uses IMAGE_SIZE by default, we can skip the argument from
image recipes to reduce redundancy.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[do not touch ar71xx]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-03-21 20:02:55 +01:00
Roger Pueyo Centelles
a66eee6336 ath79: add mikrotik subtarget
This commit creates the ath79/mikrotik subtarget in order to support
MikroTik devices based on Qualcomm Atheros MIPS SoCs.

MikroTik devices need a couple of specific features: the split MiNOR
firmware MTD format, which is not used by other devices, and the 4k
sector erase size on SPI NOR storage, which can not be added to the
ath79/generic and ath79/nand subtargets now.

Additionally, the commit moves the two MikroTik devices already in
the generic and nand subtargets to this new one.

Tested on the RB922 board and the wAP AC router.

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2020-03-17 11:50:47 +01:00
Sungbo Eo
4caaa778f7 kernel: make kmod-i2c-core selected by dependent modules
Currently kmod-i2c-* will not get into images unless kmod-i2c-core is added to
DEVICE_PACKAGES as well. By changing the dependencies from "depends on" to
"select", we do not have the issue anymore.

Furthermore, we can remove most occurrences of the package from DEVICE_PACKAGES
and similar variables, as it is now pulled by dependent modules such as:
- kmod-hwmon-lm75
- kmod-i2c-gpio
- kmod-i2c-gpio-custom
- kmod-i2c-mux
- kmod-i2c-ralink

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[do not touch ar71xx]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-03-13 15:40:43 +01:00
Davide Fioravanti
dfb7a4ce5d ath79: add support for Sitecom WLR-8100
Sitecom WLR-8100 v1 002 (marketed as X8 AC1750) is a dual band wireless
router.

Specification:

- Qualcomm Atheros SoC QCA9558
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (Macronix MX25L12845EMI-10G - SPI NOR)
- 5x 10/100/1000 Mbps Ethernet
- 3T3R 2.4 GHz (QCA9558 WMAC)
- 3T3R 5.8 Ghz (QCA9880-BR4A)
- 1x USB 3.0 (Etron EJ168A)
- 1x USB 2.0
- 9x LEDs
- 2x GPIO buttons

Everything working.
Installation and restore procedure tested

Installation
1. Connect to one of LAN (yellow) ethernet ports,
2. Open router configuration interface,
3. Go to Toolbox > Firmware,
4. Browse for OpenWrt factory image with dlf extension and hit Apply,
5. Wait few minutes, after the Power LED will stop blinking, the router
	is ready for configuration.

Restore OEM FW (Linux only)
1. Download OEM FW from website (tested with WLR-8100v1002-firmware-v27.dlf)
2. Compile the FW for this router and locate the "mksenaofw" tool
	in build_dir/host/firmware-utils/bin/ inside the OpenWrt buildroot
3. Execute "mksenaofw -d WLR-8100v1002-firmware-v27.dlf -o WLR-8100v1002-firmware-v27.dlf.out" where:
	WLR-8100v1002-firmware-v27.dlf is the path to the input file
		(use the downloaded file)
	WLR-8100v1002-firmware-v27.dlf.out is the path to the output file
		(you can use the filename you want)
4. Flash the new WLR-8100v1002-firmware-v27.dlf.out file. WARNING: Do not keep settings.

Additional notes.
The original firmware has the following button configuration:
- Press for 2s the 2.4GHz button: WPS for 2.4GHz
- Press for 2s the 5GHz button: WPS for 5GHz
- Press for 15s both 2.4GHz and 5GHz buttons: Reset
I am not able to replicate this behaviour, so I used the following configuration:
- Press the 2.4GHz button: RFKILL (disable/enable every wireless interfaces)
- Press the 5GHz button: Reset

Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
2020-03-07 11:02:13 +08:00
Manuel Giganto
b2130b9ce8 ath79: add support for Devolo Magic 2 WIFI
This patch support Devolo Magic 2 WIFI, board devolo_dlan2-2400-ac.
This device is a plc wifi AC2400 router/extender with 2 Ethernet
ports, has a G.hn PLC and uses LCMP protocol from Home Grid Forum.

Hardware:
   SoC:         AR9344
   CPU:         560 MHz
   Flash:       16 MiB (W25Q128JVSIQ)
   RAM:         128 MiB DDR2
   Ethernet:    2xLAN 10/100/1000
   PLC:         88LX5152 (MaxLinear G.hn)
   PLC Flash:   W25Q32JVSSIQ
   PLC Uplink:  1Gbps MIMO
   PLC Link:    RGMII 1Gbps (WAN)
   WiFi:        Atheros AR9340 2.4GHz 802.11bgn
                Atheros AR9882-BR4A 5GHz 802.11ac
   Switch:      QCA8337, Port0:CPU, Port2:PLC, Port3:LAN1, Port4:LAN2
   Button:      3x Buttons (Reset, wifi and plc)
   LED:         3x Leds (wifi, plc white, plc red)
   GPIO Switch: 11-PLC Pairing (Active Low)
                13-PLC Enable
                21-WLAN power

MACs Details verified with the stock firmware:
   Radio1: 2.4 GHz &wmac     *:4c Art location: 0x1002
   Radio0: 5.0 GHz &pcie     *:4d Art location: 0x5006
   Ethernet        &ethernet *:4e = 2.4 GHz + 2
   PLC uplink      ---       *:4f = 2.4 GHz + 3
Label MAC address is from PLC uplink

OEM SSID: echo devolo-$(grep SerialNumber /dev/mtd1 | grep -o ...$)
OEM WiFi password: grep DlanSecurityID /dev/mtd1|tr -d -|cut -d'=' -f 2

Recommendations: Configure and link your PLC with OEM firmware
BEFORE you flash the device. PLC configuration/link should
remain in different memory and should work straight forward
after flashing.

Restrictions: PLC link detection to trigger plc red led is not
available. PLC G.hn chip is not compatible with open-plc-tools,
it uses LCMP protocol with AES-128 and requires different
software.

Notes: Pairing should be possible with gpio switch. Default
configuration will trigger wifi led with 2.4Ghz wifi traffic
and plc white led with wan traffic.

Flash instruction (TFTP):
 1. Set PC to fixed ip address 192.168.0.100
 2. Download the sysupgrade image and rename it to uploadfile
 3. Start a tftp server with the image file in its root directory
 4. Turn off the router
 5. Press and hold Reset button
 6. Turn on router with the reset button pressed and wait ~15 seconds
 7. Release the reset button and after a short time
    the firmware should be transferred from the tftp server
 8. Allow 1-2 minutes for the first boot.

Signed-off-by: Manuel Giganto <mgigantoregistros@gmail.com>
2020-03-07 11:02:13 +08:00
Daniel Golle
d1130ad265 ath79: add support for Teltonika RUT955
Specification:

- 550/400/200 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 4x 10/100 Mbps Ethernet, with passive PoE support on LAN1
- 2T2R 2,4 GHz (AR9344)
- built-in 4G/3G module (example: Quectel EC-25EU)
- internal microSD slot (spi-mmc, buggy and disabled for now)
- RS232 on D-Sub9 port (Cypress ACM via USB, /dev/ttyACM0)
- RS422/RS485 (AR934x high speed UART, /dev/ttyATH1)
- analog 0-24V input (MCP3221)
- various digital inputs and outputs incl. a relay
- 11x LED (4 are driven by AR9344, 7 by 74HC595)
- 2x miniSIM slot (can be swapped via GPIO)
- 2x RP-SMA/F (Wi-Fi), 3x SMA/F (2x WWAN, GPS)
- 1x button (reset)
- DC jack for main power input (9-30 V)
- debugging UART available on PCB edge connector

Serial console (/dev/ttyS0) pinout:

- RX: pin1 (square) on top side of the main PCB (AR9344 is on top)
- TX: pin1 (square) on bottom side

Flash instruction:

Vendor firmware is based on OpenWrt CC release. Use the "factory" image
directly in GUI (make sure to uncheck "keep settings") or in U-Boot web
based recovery. To avoid any problems, make sure to first update vendor
firmware to latest version - "factory" image was successfully tested on
device running "RUT9XX_R_00.06.051" firmware and U-Boot "3.0.2".

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2020-02-21 22:35:12 +01:00
David Bauer
0709943182 ath79: correct Siemens WS-AP3610 blocksize
With the wrong blocksize, the rootfs was not positioned on the boundary
of a block, thus breaking the mtdsplit driver.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-02-20 10:41:12 +01:00
David Bauer
d2b8ccb1c0 ath79: add support for Siemens WS-AP3610
Hardware
--------
SoC:  Atheros AR7161
RAM:  Samsung K4H511638D-UCCC
      2x 64M DDR1
SPI:  Micron M25P128 (16M)
WiFi: Atheros AR9160 bgn
      Atheros AR9160 an
ETH:  Broadcom BCM5481
LED:  Power (Green/Red)
      ETH (Green / Blue / Yellow)
          (PHY-controlled)
      WiFi 5 (Green / Blue)
      WiFi 2 (Green / Blue)
BTN:  Reset

Serial: Cisco-Style RJ45 - 115200 8N1

Installation
------------

1. Download the OpenWrt initramfs-image. Place it into a TFTP server
   root directory and rename it to 1401A8C0.img. Configure the TFTP
   server to listen at 192.168.1.66/24.

2. Connect the TFTP server to the access point.

3. Connect to the serial console of the access point. Attach power and
   interrupt the boot procedure when prompted (bootdelay is 1 second).

4. Configure the U-Boot environment for booting OpenWrt from Ram and
   flash:

   $ setenv boot_openwrt 'setenv bootargs; bootm 0xbf080000'
   $ setenv ramboot_openwrt 'setenv serverip 192.168.1.66;
     tftpboot; bootm'
   $ saveenv

5. Load OpenWrt into memory:

   $ run ramboot_openwrt

   Wait for the image to boot.

6. Transfer the OpenWrt sysupgrade image to the device. Write the image
   to flash using sysupgrade:

   $ sysupgrade -n /path/to/openwrt-sysuograde.bin

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-02-16 15:36:29 +01:00
Adrian Schmutzler
49ff00db34 ath79: enable forceless sysupgrade from ar71xx on fritz300e
This adds the ar71xx board name to the SUPPORTED_DEVICES on ath79,
so forceless sysupgrade on this device becomes possible.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-02-13 17:33:20 +01:00
August Huber
ae61d21ca3 ath79: add support for COMFAST CF-E560AC
This commit adds support for the COMFAST CF-E560AC, an ap143 based
in-wall access point.

Specifications:
 - SoC: Qualcomm Atheros QCA9531
 - RAM: 128 MB DDR2 (Winbond W971GG6SB-25)
 - Storage: 16 MB NOR (Winbond 25Q128JVSO)
 - WAN: 1x 10/100 PoE ethernet (48v)
 - LAN: 4x 10/100 ethernet
 - WLAN1: QCA9531 - 802.11b/g/n - 2x SKY85303-21 FEM
 - WLAN2: QCA9886 - 802.11ac/n/a - 2x SKY85735-11 FEM
 - USB: one external USB2.0 port
 - UART: 3.3v, 2.54mm headers already populated on board
 - LED: 7x external
 - Button: 1x external
 - Boot: U-Boot 1.1.4 (pepe2k/u-boot_mod)

MAC addressing:

- stock
  LAN    *:40 (label)
  WAN    *:41
  5G     *:42
  2.4G   *:4a

- flash (art partition)
  0x0    *:40 (label)
  0x6    *:42
  0x1002 *:41
  0x5006 *:43

This device contains valid MAC addresses in art 0x0, 0x6, 0x1002 and
0x5006, however the vendor firmware only reads from art:0x0 for the LAN
interface and then increments in 02_network. They also jump 8 addresses
for the second wifi interface (2.4 GHz). This behavior has been duplicated
in the DTS and ath10k hotplug to align addresses with the vendor firmware
v2.6.0.

Recovery instructions:

This device contains built-in u-boot tftp recovery.

1. Configure PC with static IP 192.168.1.10/24 and tftp server.
2. Place desired image at /firmware_auto.bin at tftp root.
3. Connect device to PC, and power on.
4. Device will fetch flash from tftp, flash and reboot into new image.

Signed-off-by: August Huber <auh@google.com>
[move jtag_disable_pins, remove unnecessary statuses in DTS, remove
duplicate entry in 11-ath10k-caldata, remove hub_port0 label in DTS]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-02-03 16:18:08 +01:00
Michal Cieslakiewicz
3b99d67639 ath79: WNDR3700 v2: add dash before version in device name
Adapt Netgear WNDR3700v2 device identification string to ath79 naming
scheme by changing from 'wndr3700v2' to 'wndr3700-v2' (affects config,
makefile, init scripts and device tree definition).

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
2020-02-03 11:28:05 +01:00
Adrian Schmutzler
b4d3110ac1 ath79: add support for GL.iNet 6408/6416 (GL.iNet V1)
This ports the GL.iNet 6408/6416 from ar71xx.

The GL-Connect GL.iNet v1 routers are basically a TP-Link TL-WR710N with
more DRAM/Flash and console/GPIO header in the same small form-factor.

Specifications:
 - SoC: Atheros AR9331
 - CPU: 400 MHz
 - Flash: 8/16 MiB
 - RAM: 64 MiB
 - WiFi: 2.4 GHz b/g/n (SoC)
 - Ethernet: 2x 100M ports (LAN/WAN)
 - USB: 1x 2.0

The difference between 6408 and 6416 is just the flash size. It looks like
only the 16 MiB version has been advertised, while the 6408 is a modified
version. There are also 1-port versions sold by third parties.

Installation:
Install the sysupgrade image via stock firmware GUI or upload it via uboot
(web-based). The device will be available at 192.168.1.1.

Attention: In ar71xx, the same board name is used for both flash versions.
So, please make sure you flash the correct ath79 image when upgrading.

This has been device-tested on a GL.iNet 6416.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-01-29 18:56:04 +01:00
Adrian Schmutzler
07ce940b77 ath79: fix SUPPORTED_DEVICES not matching ar71xx board names
Based on a script for comparison, this fixes (hopefully) all errors
in SUPPORTED_DEVICES for ar71xx->ath79 upgrade.

Devices where old string is removed as the device does not exist
in ar71xx:
- dlink_dir-859-a1
- tplink_archer-a7-v5
- tplink_cpe510-v3

Devices where string is changed because it did not match the board
name in ar71xx:
- tplink_tl-mr3220-v1
- tplink_tl-mr3420-v1
- tplink_tl-wr2543-v1
- tplink_tl-wr741nd-v4
- tplink_tl-wr841-v7
- ubnt_unifiac-mesh
- ubnt_unifiac-mesh-pro
- ubnt_unifiac-pro

For this device, the correct string could not be found, but we could
not determine the correct one. Thus, the string is removed for now:
- tplink_tl-wr740n-v4

The script for checking this is quite simple (note that newer
entries, i.e. ath79->ath79 upgrade, are displayed as missing):

  newpath=target/linux/ath79/image/
  oldpath=target/linux/ar71xx/base-files/lib/ar71xx.sh

  for s in $(grep -roh "SUPPORTED_DEVICES.*" $newpath | sed 's/SUPPORTED_DEVICES *.= *//'); do
    found="Missing"
    grep -q -r "\"$s\"" $oldpath && found="Found"
    echo "$s: $found."
  done

The errors might be filtered by appending 'grep "Missing"' to the script.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-01-23 16:09:58 +01:00
Roger Pueyo Centelles
6aaa5ce2c5 ath79: add support for MikroTik RouterBOARD wAP G-5HacT2HnD
This commit adds support for the MikroTik RouterBOARD wAP G-5HacT2HnD
(wAP AC), a small weatherproof dual band, dual-radio 802.11ac
wireless AP with integrated omnidirectional anntennae and one
10/100/1000 Mbps Ethernet port.

See https://mikrotik.com/product/RBwAPG-5HacT2HnD for more info.

Specifications:
 - SoC: Qualcomm Atheros QCA9556
 - RAM: 64 MB
 - Storage: 16 MB NOR
 - Wireless:
   · Atheros AR9550 (SoC) 802.11b/g/n 2x2:2, 2 dBi antennae
   · Qualcomm QCA9880 802.11a/n/ac 3x3:3, 2 dBi antennae
 - Ethernet: Atheros AG71xx (SoC, AR8033), 1x 1000/100/10 port,
   passive PoE in

Working:
 - Board/system detection
 - Sysupgrade
 - Serial console
 - Ethernet
 - 2.4 GHz radio
 - 5 GHz radio and LED
 - Reset button

Not working/Unsupported:
 - 2.4 GHz LED
 - AP/CAP LED
 - ZT2046Q SPI temperature and voltage sensor

This adds the basic features for supporting MikroTik devices:
 - a common recipe for mikrotik images in common-mikrotik.mk
 - support for minor (MikroTik NOR) split firmware (only for
   generic subtarget so far)

Acknowledgments: Robert Marko <robimarko@gmail.com>
                 Andrew Cameron <apcameron@softhome.net>
                 Koen Vandeputte <koen.vandeputte@ncentric.com>
                 Chuanhong Guo <gch981213@gmail.com>

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Co-developed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2020-01-23 15:28:03 +01:00
David Bauer
c9ac7b1729 ath79: add support for D-Link DIR-505
This commit adds support for the D-Link DIR-505, previously supported in
ar71xx.

Hardware
--------
SoC:   Atheros AR9330
FLASH: 8M SPI-NOR
RAM:   64M
WIFI:  1T1R 1SS Atheros AR9330
LED:   Power green, Status red
BTN:   WPS, Reset

Installation
------------
Currently, installation is only possible by sysupgrading from an earlier
OpenWrt version, U-Boot TFTP or a modded U-Boot. I do not have the
original bootloader from D-Link on my device anymore, so i cannot test
the factory image.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-01-15 20:38:46 +01:00
Tomasz Maciej Nowak
2248df303d ath79: wlr-7100: use ath10k-ct smallbuffers package variant
The memory hacks got removed from ath10k with 1e27bef ("mac80211: remove
ath10k_pci memory hacks"). As this device has low amount of RAM, switch
to ath-10k-ct small buffers variant, to avoid the OOM Reaper.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2020-01-15 19:53:49 +01:00
Paul Fertser
db992e7b53 ath79: use ath10k-ct-smallbuffers for 64 MiB devices
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
2019-12-24 00:57:56 +01:00
Adrian Schmutzler
95030ac0b6 ath79: rename ATH_SOC to SOC
This replaces ATH_SOC by the newly introduced common SOC device
variable.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-20 01:12:42 +01:00
Adrian Schmutzler
0757f7fedc ath79: harmonize line breaks in image Makefiles
This harmonizes the line wrapping in image Makefile device
definitions, as those are frequently copy-pasted and are a common
subject of review comments. Having the treatment unifying should
reduce the cases where adjustment is necessary afterwards.

Harmonization is achieved by consistently (read "strictly")
applying certain rules:
- Never put more than 80 characters into one line
- Fill lines up (do not break after 40 chars because of ...)
- Use one tab for indent after wrapping by "\"
- Only break after pipe "|" for IMAGE variables

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-20 00:29:05 +01:00
Piotr Dymacz
e5d4c09667 ath79: add support for YunCore XD4200 and A782
YunCore XD4200 ('XD4200_W6.0' marking on PCB) is Qualcomm/Atheros based
(QCA9563, QCA9886, QCA8334) dual-band, Wave-2 AC1200 ceiling AP with PoE
(802.3at) support. A782 model ('T750_V5.1' marking on PCB) is a smaller
version of the XD4200, with similar specification but lower TX power.

Specification:

- QCA9563 (775 MHz)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 2x 10/100/1000 Mbps Ethernet (QCA8334), with 802.3at PoE support (WAN)
- Wi-Fi 2.4 GHz:
  - XD4200: 2T2R (QCA9563), with ext. PA (SKY65174-21) and LNA
  - A782: 2T2R (QCA9563), with ext. FEM (SKY85329-11)
- Wi-Fi 5 GHz:
  - XD4200: 2T2R (QCA9886), with ext. FEM (SKY85728-11)
  - A782: 2T2R (QCA9886), with ext. FEM (SKY85735-11)
- LEDs:
  - XD4200: 5x (2x driven by SOC, 1x driven by AC radio, 2x Ethernet)
  - A782: 3x (1x RGB, driven by SOC and radio, 2x Ethernet)
- 1x button (reset)
- 1x UART (4-pin, 2.54 mm pitch) header on PCB
- 1x DC jack (12 V)

Flash instructions:

If your device comes with generic QSDK based firmware, you can login
over telnet (login: root, empty password, default IP: 192.168.188.253),
issue first (important!) 'fw_setenv' command and then perform regular
upgrade, using 'sysupgrade -n -F ...' (you can use 'wget' to download
image to the device, SSH server is not available):

  fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000"
  sysupgrade -n -F openwrt-...-yuncore_...-squashfs-sysupgrade.bin

In case your device runs firmware with YunCore custom GUI, you can use
U-Boot recovery mode:

1. Set a static IP 192.168.0.141/24 on PC and start TFTP server with
   'tftp' image renamed to 'upgrade.bin'
2. Power the device with reset button pressed and release it after 5-7
   seconds, recovery mode should start downloading image from server
   (unfortunately, there is no visible indication that recovery got
   enabled - in case of problems check TFTP server logs)

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2019-11-25 17:32:46 +01:00
Vincent Wiemann
8016f64864 ath79: add support for YunCore TFTP image generation
YunCore QCA9k based devices released in 2019 require a custom TFTP image
for U-Boot built-in recovery mode (triggered with reset button). Image
has to be prepended with 'YUNCORE' keyword followed by U-Boot CLI
commands which will be executed later. Images without the custom header
will be ignored by U-Boot.

To be able to support both the vendor firmware (QSDK) and OpenWrt flash
layouts, used here commands change the 'bootcmd' before flashing image.

This commit adds generic helper script for YunCore devices with 16 MB of
flash and enables TFTP image generation for A770 model.

Signed-off-by: Vincent Wiemann <vincent.wiemann@ironai.com>
[pepe2k@gmail.com: commit description reworded, recipe renamed]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2019-11-25 17:32:46 +01:00
Adrian Schmutzler
fc44a8481c ath79: fix sysupgrade from ar71xx for WNDR3700 V2 and WNDR3800(CH)
ar71xx has just one board name "wndr3700" for WNDR3700 V1/V2,
WNDR3800 and WNDR3800CH, whereas ath79 provides separate images for
the boards. So, update SUPPORTED_DEVICES to store the correct
ar71xx board names.

Fixes: FS#2510

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-14 23:14:35 +01:00
Jeff Kletsky
b496a2294c ath79: GL-AR750S: provide NAND support; increase kernel to 4 MB
The GL.iNet GL-AR750S has been supported by the ar71xx and ath79
platforms with access to its 16 MB NOR flash, but not its 128 MB
SPI NAND flash.

This commit provides support for the NAND through the upstream
SPI-NAND framework.

At this time, the OEM U-Boot appears to only support loading the
kernel from NOR. This configuration is preserved as this time,
with the glinet,gl-ar750s-nand name reserved for a potential,
future, NAND-only boot.

The family of GL-AR750S devices on the ath79 platform now includes:

  * glinet,gl-ar750m-nor-nand   "nand" target
  * glinet,gl-ar750m-nor        "nand" target (NAND-aware)

NB: This commit increases the kernel size from 2 MB to 4 MB

"Force-less" sysupgrade is presently supported from the current
versions of following NOR-based firmwre images to the version of
glinet,gl-ar750s-nor firmware produced by this commit:

  * glinet,gl-ar750s     -- OpenWrt 19.07 ar71xx
  * glinet,gl-ar750s     -- OpenWrt 19.07 ath79

Users who have sucessfully upgraded to glinet,gl-ar750m-nor may then
flash glinet,gl-ar750m-nor-nand with sysupgrade to transtion to the
NAND-based variant.

Other upgrades to these images, including directly to the NAND-based
glinet,gl-ar750s-nor-nand firmware, can be accomplished through U-Boot.

NB: See "ath79: restrict GL-AR750S kernel build-size to 2 MB" which
enables flashing of NAND factory.img with the current GL-iNet U-Boot,
"U-Boot 1.1.4-gcf378d80-dirty (Aug 16 2018 - 07:51:15)"

The GL-AR750S OEM U-Boot allows upload and flashing of either NOR
firmware (sysupgrade.bin) or NAND firmware (factory.img) through its
HTTP-based GUI. Serial connectivity is not required.

The glinet,gl-ar750s-nor and glinet,gl-ar750s-nor-nand images
generated after this commit flash each other directly.

This commit changes the control of the USB VBUS to gpio-hog from
regulator-fixed introduced by commit 0f6b944c92. This reduces the
compressed kernel size by ~14 kB, with no apparent loss of
functionality. No other ath79-nand boards are using regulator-fixed
at this time.

Note: mtd_get_mac_binary art 0x5006 does not return the proper MAC
and the GL.iNet source indicates that only the 0x0 offset is valid

The ar71xx targets are unmodified.

Cc: Alexander Wördekemper <alexwoerde@web.de>

Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
2019-11-14 14:38:58 +08:00
Jeff Kletsky
b591cabd39 ath79: add GL.iNet GL-AR300M16 as NOR-only board
The GL.iNet GL-AR300M series of devices includes variants without NAND
and only the 16 MB NOR flash. These include the GL-AR300M16 and the
GL-AR300M-Lite (already with its own board name).

This board-name addition provides disambiguation from the NAND-bearing
GL-AR300M devices, both for OpenWrt code and for end users.

Kernel and firmware support for NAND and UBI will add ~320 kB to the
overall firmware size at this time. This NOR-only option continues to
provide more compact firmware for both the GL-AR300M16 as well as
those who wish to use it as an alternate or primary, NOR-resident
firmware on the GL-AR300M.

The ar71xx targets are unmodified.

Installation
------------

Install through OEM U-Boot (HTTP-based) or `sysupgrade --force` when
booted from NOR and running OEM or OpenWrt, NOR-based firmware.

As one of the intentions is disambiguation from NAND-bearing units,
users who have flashed this firmware onto a device with NAND would
need to use U-Boot or `sysupgrade --force` to flash firmware that
again supports NAND.

There are no additional SUPPORTED_DEVICES as it is not possible to
determine if a device does or does not have NAND based on
either the OEM's or OpenWrt's board names prior to this patch.

Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
2019-11-14 14:38:58 +08:00
Jeff Kletsky
55e6c903ae ath79: GL-AR300M: provide NAND support; increase to 4 MB kernel
The GL.iNet GL-AR300M has been supported by the ar71xx and ath79
platforms with access to its 16 MB NOR flash, but not its 128 MB
SPI NAND flash.

This commit provides support for the NAND through the upstream
SPI-NAND framework. Devices with both NOR and NAND flash can support
independent firmware on each, with U-Boot able to boot from either.
The OEM U-Boot will fall back to the NOR firmware after three
"unsuccessful" boots.

The family of GL-AR300M devices on the ath79 platform now includes:

  * glinet,gl-ar300m-lite       "generic" target, NOR-only board
  * glinet,gl-ar300m-nand       "nand" target
  * glinet,gl-ar300m-nor        "nand" target (NAND-aware)

NB: This commit increases the kernel size from 2 MB to 4 MB

"Force-less" sysupgrade is presently supported from the current
versions of following NOR-based firmwre images to the version of
glinet,gl-ar300m-nor firmware produced by this commit:

  * gl-ar300m            -- OEM v3 NOR    ar71xx (openwrt-ar300m16-*.bin)
  * gl-ar300m            -- OpenWrt 18.06 ar71xx
  * gl-ar300m            -- OpenWrt 19.07 ar71xx

Other upgrades to these images should be performed through U-Boot.

The GL-AR300M OEM U-Boot allows upload and flashing of either NOR
firmware (sysupgrade.bin) or NAND firmware (factory.img) through its
HTTP-based GUI. Serial connectivity is not required.

The glinet,gl-ar300m-nand and glinet,gl-ar300m-nor images generated
after this commit should safely flash each other using sysupgrade.

The boot counter is implemented by the OEM using u-boot-env. At this
time, it does not appear that the switch on the side of the unit can
be used to select NOR vs. NAND boot and the fail-over is only from
NAND to NOR. To save flash wear, it is only reset when running the
glinet,gl-ar300m-nand firmware.

NAND-specific base-files are used to remove impact on existing
generic and tiny targets.

As there is now no "generic" build appropriate for the GL-AR300M16,
(or for users of the GL-AR300M that do not need access to NAND)
it will be introduced in a subsequent commit.

Note: `mtd_get_mac_binary art 0x6` does not return the proper MAC
and the GL.iNet source indicates that only the 0x0 offset is valid

The ar71xx targets are unmodified.

Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
2019-11-14 14:38:58 +08:00
Michal Cieslakiewicz
f85d56bb03 ath79: add support for Netgear WNR2200
This patch adds ath79 support for Netgear WNR2200.
Router was previously supported by ar71xx target only (8 MiB variant).
Netgear WNR2200 has two flash versions - 8MiB sold in EU, US etc. and
16 MiB for Russia and China markets. Apart from flash size both variants
share the same hardware specification.

Specification
=============
  * Description: Netgear WNR2200
  * Loader: U-boot
  * SOC: Atheros AR7241 (360 MHz)
  * RAM: 64 MiB
  * Flash: 8 MiB or 16 MiB (SPI NOR)
	- U-boot binary: 256 KiB
	- U-boot environment: 64 KiB
	- Firmware: 7808 KiB or 16000 KiB
	- ART: 64 KiB
  * Ethernet: 4 x 10/100 LAN + 1 x 10/100 WAN
  * Wireless: 2.4 GHz b/g/n (Atheros AR9287)
  * USB: yes, 1 x USB 2.0
  * Buttons:
	- Reset
	- WiFi (rfkill)
	- WPS
  * LEDs:
	- Power (amber/green)
	- WAN (amber/green)
	- WLAN (blue)
	- 4 x LAN (amber/green)
	- WPS (green)
  * UART: 4-pin connector JP1, 3.3V (Vcc, TX, RX, GND), 115200 8N1
  * Power supply: DC 12V 1.5A
  * MAC addresses: LAN on case label, WAN +1, WLAN +2

Installation
============
  * TFTP recovery
  * TFTP via U-boot prompt
  * sysupgrade
  * Web interface

Test build configuration
========================
CONFIG_TARGET_ath79=y
CONFIG_TARGET_ath79_generic=y
CONFIG_TARGET_ath79_generic_DEVICE_netgear_wnr2200-8m=y
CONFIG_ALL_KMODS=y
CONFIG_DEVEL=y
CONFIG_CCACHE=y
CONFIG_COLLECT_KERNEL_DEBUG=y
CONFIG_IMAGEOPT=y
CONFIG_KERNEL_DEBUG_INFO=y
CONFIG_KERNEL_DEBUG_KERNEL=y

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
2019-11-01 21:14:55 +01:00
Adrian Schmutzler
2d2fa2fd2d ath79: fix remaining IMAGE_SIZE issues
This fixes the remaining IMAGE_SIZE issues in ath79 target.
All devices in target have been checked, so together with
previous patches this target should be "clean" afterwards.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-10-27 14:03:03 +01:00
Jeff Kletsky
18848312c5 ath79: Refactor GL.iNet GL-AR300M-series generic.mk
Rework DEVICE_VENDOR, DEVICE_MODEL, and DEVICE_VARIANT
for the GL-AR300M series on the ath79-generic target.

Changes GL-AR300M-Lite to the current form with
DEVICE_VARIANT := Lite (board name is unchanged)

Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
2019-10-24 23:06:26 +02:00
Tomasz Maciej Nowak
1bc921f419 ath79: add support for Sitecom WLR-7100
Sitecom WLR-7100 v1 002 (marketed as X7 AC1200) is a dual band wireless
router.

Specification
SoC: Atheros AR1022
RAM: 64 MB DDR2
Flash: 8 MB SPI NOR
WIFI: 2.4 GHz 2T2R integrated
      5 GHz 2T2R QCA9882 integrated (connected to PCIe lane)
Ethernet: 5x 10/100/1000 Mbps QCA8337N
USB: 1x 2.0
LEDS: 4x GPIO controlled, 5x switch
Buttons: 2x GPIO controlled
UART: row of 4 unpopulated holes near USB port, starting count from
      white triangle on PCB
      1. VCC 3.3V, 2. GND, 3. TX, 4. RX
      baud: 115200, parity: none, flow control: none

Installation
1. Connect to one of LAN (yellow) ethernet ports,
2. Open router configuration interface,
3. Go to Toolbox > Firmware,
4. Browse for OpenWrt factory image with dlf extension and hit Apply,
5. Wait few minutes, after the Power LED will stop blinking, the router
   is ready for configuration.

Known issues
5GHz LED doesn't work

Additional information
When TX line on UART is connected, and board is switched on from power
off state, the DDR memory training may fail.
If connected to UART, when prompted for number on boot, one can enter
number 4 to open bootloader (U-Boot) command line.
OEM firmware shell password is: SitecomSenao
useful for creating backup of original firmware.
There is also another revision of this device (v1 001), which may or may
not work with introduced images.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-10-21 13:01:10 +02:00
Roger Pueyo Centelles
bba6646b5c ath79: add support for COMFAST CF-E313AC
This patch adds support for the COMFAST CF-E313AC, an  outdoor wireless
CPE with two Ethernet ports and a 802.11ac radio.

Specifications:

 - QCA9531 SoC
 - 650/400/216 MHz (CPU/DDR/AHB)
 - 1x 10/100 Mbps WAN Ethernet, 48V PoE-in
 - 1x 10/100 Mbps LAN Ethernet, pass-through 48V PoE-out
 - 1x manual pass-through PoE switch
 - 64 MB RAM (DDR2)
 - 16 MB FLASH
 - QCA9886 2T2R 5 GHz 802.11ac, 23 dBm
 - 12 dBi built-in antenna
 - POWER/LAN/WAN/WLAN green LEDs
 - 4x RSSI LEDs (2x red, 2x green)
 - UART (115200 8N1)

Flashing instructions:

 The original firmware is based on OpenWrt so a sysupgrade image can be
 installed via the stock web GUI. Settings from the original firmware
 will be saved and restored on the new one, so a factory reset will be
 needed. To do so, once the new firmware is flashed, enter into failsafe
 mode by pressing the reset button several times during the boot
 process, while the WAN LED flashes, until it starts flashing faster.
 Once in failsafe mode, perform a factory reset as usual.

 Alternatively, the U-boot bootloader contains a recovery HTTP server
 to upload the  firmware. Push the reset button while powering the
 device on and keep it pressed for >10 seconds. The device's LEDs will
 blink several times and the recovery page will be at
 http://192.168.1.1; use it to upload the sysupgrade image.

Note:

 Four MAC addresses are stored in the "art" partition (read-only):
  - 0x0000: 40:A5:EF:AA:AA:A0
  - 0x0006: 40:A5:EF:AA:AA:A2
  - 0x1002: 40:A5:EF:AA:AA:A1
  - 0x5006: 40:A5:EF:AA.AA:A3 (inside the 5 GHz calibration data)

 The stock firmware assigns MAC addresses to physical and virtual
 interfaces in a very particular way:
  - eth0 corresponds to the physical Ethernet port labeled as WAN
  - eth1 corresponds to the physical Ethernet port labeled as LAN

  - eth0 belongs to the bridge interface br-wan
  - eth1 belongs to the bridge interface br-lan

  - eth0 is assigned the MAC from 0x0 (*:A0)
  - eth1 is assigned the MAC from 0x1002 (*:A1)

  - br-wan is forced to use the MAC from 0x1002 (*:A1)
  - br-lan is forced to use the MAC from 0x0 (*:A0)

  - radio0 uses the calibration data from 0x5000 (which contains
    a valid MAC address, *:A3). However, it is overwritten by the
    one at 0x6 (*:A2)

 This commit preserves the LAN/WAN roles of the physical Ethernet
 ports (as labeled on the router) and the MAC addresses they expose
 by default (i.e., *:A0 on LAN, *:A1 on WAN), but swaps the position
 of the eth0/eth1 compared to the stock firmware:
  - eth0 corresponds to the physical Ethernet port labeled as LAN
  - eth1 corresponds to the physical Ethernet port labeled as WAN

  - eth0 belongs to the bridge interface br-lan
  - eth1 is the interface at @wan

  - eth0 is assigned the MAC from 0x0 (*:A0)
  - eth1 is assigned the MAC from 0x1002 (*:A1)

  - br-lan inherits the MAC from eth0 (*:A0)
  - @wan inherits the MAC from eth1 (*:A1)

  - radio0's MAC is overwritten to the one at 0x6

This way, eth0/eth1's positions differ from the stock firmware, but
the weird MAC ressignations in br-lan/br-wan are avoided while the
external behaviour of the router is maintained. Additionally, WAN
port is connected to the PHY gmac, allowing to monitor the link
status (e.g., to restart DHCP negotiation when plugging a cable).

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2019-10-13 20:34:57 +08:00
Adrian Schmutzler
794d4b6652 treewide: remove kmod-usb-core from DEVICE_PACKAGES
This removes _all_ occurrences of kmod-usb-core from
DEVICE_PACKAGES and similar variables.

This package is pulled as dependency by one of the following
packages in any case:
- kmod-usb-chipidea
- kmod-usb-dwc2
- kmod-usb-ledtrig-usbport
- kmod-usb-ohci
- kmod-usb2
- kmod-usb2-pci
- kmod-usb3

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[remove kmod-usb-core from EnGenius ESR600]
Signed-off-by: David Bauer <mail@david-bauer.net>
2019-10-06 21:28:49 +02:00
Dmitry Tunin
00ed75f47f ath79: add support of Netgear WNDR3800CH
Add support for the ar71xx supported Netgear WNDR3800CH to ath79.
The device is identical to WNDR3800 except NETGEAR_BOARD_ID.

Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
Reviewed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-09-21 23:41:31 +02:00
Tomasz Maciej Nowak
66b7c82bb1 ath79: image: pad kernel for Adtran/Bluesocket devices
It has been reported that using the sysupgrade-tar image will trigger
"lzma_decode failed error". The RedBoot bootloader always loads data
from flash till block size boundary, so if there's no padding it'll also
load the beginning of rootfs, and it seems that lzma_decoder can't handle
that garbage data. Previously the script creating combined-image
silently padded the kernel and rootfs, but since sysupgrade-tar doesn't,
pad the default kernel image.

Fixes: 900330f ("ath79: image: retire combined-image for Adtran/Bluesocket
devices")
Cc: Brian Gonyer <bgonyer@gmail.com>
Cc: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-09-21 22:17:39 +02:00
Adrian Schmutzler
d1e3f32dcf ath79: sort device definitions in image/*
This applies alphabetic sorting to devices in image/* files.

For certain cases, this patch deviates from strict sorting, e.g.
to ensure that v10 comes after v9.

While at it, fix an indent and remove some useless empty lines.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-09-21 22:17:39 +02:00